S5PC100 and S5PC110 clock registers differs in many places, rename all
previously defined registers to be S5PC100 specific. Remove all power
management registers. They will be added later to a separate file.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S5PC110 and S5PC100 register maps differs in many places, rename all
defined registers to be S5PC100 specific. PA_SYS register known from
S3C64XX series has been renamed to more adequate PA_CLK. Also system map
has been also updated to cover more integrated peripherals.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We inted to re-organise the plat-s3c/plat-s3c24xx/plat-s3c64xx into a
more generic plat-samsung with less code in the other plat- directories
to make it easier to port new devices and try and clear up some of the
naming issues with newer devices.
Start by creating a small arch/arm/plat-samsung with no actuall code in
so we can move items in as we process them.
Add this to arch/arm to allow it to build things once support is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates defconfig to enable options needed to properly
boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs,
TWL4030 GPIO and sound drivers.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some drivers have dependencies on this, and therefore should be
enabled.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original TWL4030 keypad driver from linux-omap used KEY()
macro defined as (col, row), but while it was merged upstream
it was changed to use matrix keypad infrastructure, which uses
(row, col) format. Update the keymap in board file to match
layout of mainline driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch provides the following fixes:
- keep kernel small enough to boot with standard tools,
- ensure compatibility with both new and legacy distros,
- turn on support for recently added or fixed hardware features.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzysz@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially
starting correctly, breaks with the following error messages:
omapfb omapfb: resetting (status 0xffffff96,reset count 1)
...
omapfb omapfb: resetting (status 0xffffff96,reset count 100)
omapfb omapfb: too many reset attempts, giving up.
Looking closer at this I have found that it had been broken almost 2 years ago
with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1.
The definite reason for broken omapfb/lcdc behavoiur in PM mode
appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD
DMA possibly running. The bit were set based on return value of the
omap_dma_running() function that did not check for dedicated LCD DMA
channel status. The patch below fixes this.
Note that the hardcoded register value will be fixed during the next merge
cycle to use OMAP_LCDC_ defines. Currently the OMAP_LCDC_ defines are local
to drivers/video/omap/lcdc.c, so let's not start moving those right now.
Created against linux-2.6.32-rc6
Tested on Amstrad Delta
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors
and actually fixes one in mailbox.c.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bug could cause irq enable bit of one DMA channel is
cleared/set unexpectedly when 2 (or more) drivers are calling
omap_request_dma()/omap_free_dma() simultaneously
Signed-off-by: Fei Yang <AFY095@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use a definition for the cmpxchg SWI instead of hard-coding the number.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
We need to free the buff and lli nodes if the buffer queue is
not CIRCULAR.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
buffdone callback should be called per buffer request with pointer
to the latest serviced request.
'next' should point to the one next to currently active.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some devices don't seem to work if the source and desitnation transfer
widths are not same. For example, SPI dma xfers, with 8bits/word,
don't work without this patch.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Replace s3c64xx_dma_tcirq and s3c64xx_dma_errirq with the common
s3c64xx_dma_buffdone.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ensure the DMA buffer points are not updated from
another source during the process of enquing a buffer.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
[ben-linux@fluff.org: Updated patch comment]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The recent changes to arch/arm/mach-s3c6400/include/mach/dma.h have
left an out of date comment in there as well as accidentally changing
the type of the function.
Fix the commit 54489cd46a
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch removes the duplicated s3c_dma_has_circular() definition and so fixes
compilation for S3C64xx.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WM835x has some GPIOs on it, allocate some space so we can use
them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When used with the WM1190-EV1 board we can use the internal pull up
resistor of the CPU to provide the required pull for the IRQ line.
Without this interrupts from the WM835x don't work in the default
WM1190-EV1 hardwaer configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
That code was refactored a long time ago, but one particular label
didn't get adjusted properly which broke the listing of supported
machines.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of allocating PCI devices I/O port bus addresses from the
000xxxxx I/O port range as intended, due to a bus versus physical
address mixup, the Kirkwood PCIe handling code inadvertently
allocated I/O port bus addresses from the f20xxxxx address range
(which is the physical address range of the PCIe I/O mapping window),
but then direct all I/O port accesses to bus addresses 000xxxxx,
which would then not be decoded at all.
Fix this by setting the base address of the PCIe I/O space struct
resource to KIRKWOOD_PCIE_IO_BUS_BASE instead of the incorrect
KIRKWOOD_PCIE_IO_PHYS_BASE, and fix up __io() to expect addresses
offsetted by the former instead of the latter.
(The suggested fix of directing I/O port accesses from the host to
bus addresses f20xxxxx instead has the problem that assigning full
32bit I/O port bus addresses (f20xxxxx) doesn't work on all PCI
devices, as not all PCI devices implement full 32 bit BAR registers
for I/O ports. We should really try to allocate I/O port bus
addresses that fit in 16 bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
kirkwood_timer_init() and kirkwood_pcie_setup() lack of __init which
causes following warnings:
WARNING: vmlinux.o(.text+0x9568): Section mismatch in reference from
the function kirkwood_timer_init() to the function
.init.text:kirkwood_find_tclk()
The function kirkwood_timer_init() references
the function __init kirkwood_find_tclk().
This is often because kirkwood_timer_init lacks a __init
annotation or the annotation of kirkwood_find_tclk is wrong.
WARNING: vmlinux.o(.text+0x979c): Section mismatch in reference from
the function kirkwood_pcie_setup() to the function
.init.text:orion_pcie_setup()
The function kirkwood_pcie_setup() references
the function __init orion_pcie_setup().
This is often because kirkwood_pcie_setup lacks a __init
annotation or the annotation of orion_pcie_setup is wrong.
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
NOTE:
1. Macro style is so strange.
2. The value 0xc0 is not match with KS8695 manual. It should be 0x0c.
Signed-off-by: zeal <zealcook@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RealView PBX board has two 512MB blocks of memory - one at
0x70000000 (with 256MB mirror at 0) and another at 0x20000000. Only the
block at 0x70000000 (or the mirror at 0) may be used for DMA (e.g.
framebuffer). This patch adds the sparsemem definitions to allow the use
of all the memory split as follows:
256MB @ 0x00000000 (ZONE_DMA)
512MB @ 0x20000000 (ZONE_NORMAL)
256MB @ 0x80000000 (ZONE_NORMAL)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The platsmp.c file defines the REALVIEW_SYS_FLAGS* macros which are
already present in platform.h. Just use the latter.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a realview_fixup() function called during booting to set
up the memory banks. This way there is no need to pass a "mem=" argument
on the kernel command line.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If Linux is running in non-secure mode, this register may have been
already initialised and writing to the control register not allowed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If running in non-secure mode, enabling this register will fault.
Signed-off-by: Tony Thompson <Anthony.Thompson@arm.com>
Acked-by: Srinidhi Kasagar <srinidhikasagar@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux:
ARM: S3C2410: Fix sparse warnings in arch/arm/mach-s3c2410/gpio.c
ARM: S3C2440: mini2440: Fix spare warnings
ARM: S3C24XX: Fix warnings in arch/arm/plat-s3c24xx/gpio.c
ARM: S3C2440: mini2440: Fix missing CONFIG_S3C_DEV_USB_HOST
ARM: S3C24XX: arch/arm/plat-s3c24xx: Move dereference after NULL test
ARM: S3C: Fix adc function exports
ARM: S3C2410: Fix link if CONFIG_S3C2410_IOTIMING is not set
ARM: S3C24XX: Introduce S3C2442B CPU
ARM: S3C24XX: Define a macro to avoid compilation error
ARM: S3C: Add info for supporting circular DMA buffers
ARM: S3C64XX: Set rate of crystal mux
ARM: S3C64XX: Fix S3C64XX_CLKDIV0_ARM_MASK value
Since interrupt handler is changed to use interrupt priority, we also need
to save and restore these interrupt controller registers in suspend/resume
routine.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Palm Tungsten C keyboard structure has swapped
rows/cols gpio structures and does not work.
This patch fixes it.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Borzoi, Terrier and Akita use the same NAND Flash OOB layout, which
seems to be different from Spitz for some reason. Here is a fix.
When the code was ported to the platform data, the map was applied just
for Akita.
After this patch, Flash works again on Borzoi. Terrier still has a
problem with partition table different from Borzoi (unfixable without
reading of the system configuration in flash) and JFFS2 partitions can
be mounted (with some "Empty flash at ... ends at ..." in the syslog).
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: ensure initial page tables are setup for SMP systems
ARM: 5776/1: Check compiler version and EABI support when adding ARM unwind support.
ARM: 5774/1: Fix Realview ARM1176PB board reboot
ARM: Fix errata 411920 workarounds
ARM: Fix sparsemem with SPARSEMEM_EXTREME enabled
ARM: Use GFP_DMA only for masks _less_ than 32-bit
ARM: integrator: allow Integrator to be built with highmem
ARM: Fix signal restart issues with NX and OABI compat
