Pass the POSIX lock owner ID to the flush operation.
This is useful for filesystems which don't want to store any locking state
in inode->i_flock but want to handle locking/unlocking POSIX locks
internally. FUSE is one such filesystem but I think it possible that some
network filesystems would need this also.
Also add a flag to indicate that a POSIX locking request was generated by
close(), so filesystems using the above feature won't send an extra locking
request in this case.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wd33c93 needs a small delay before a new command can be started.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first 25% of libata-core.c converted to the new debugging scheme.
Signed-off-by: <petkov@math.uni-muenster.de>
(with addition of ATA_MSG_WARN to standard msg_enable by me)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out parts of ata_scsi_find_dev to be reused in
future SAS/SATA patches.
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prepare for changes required to support SATA devices
attached to SAS HBAs. For these devices we don't want to
use host_set at all, since libata will not be the owner
of struct scsi_host.
Signed-off-by: Brian King <brking@us.ibm.com>
(with slight merge modifications made by...)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, the only per-dev EH action is REVALIDATE. EH used to
exploit ehi->dev to do selective revalidation on a ATA bus. However,
this is a bit hacky and makes it impossible to request selective
revalidation from outside of EH or add another per-dev EH action.
This patch adds per-dev EH action mask eh_info->dev_action[] and
update EH to use this field for REVALIDATE. Note that per-dev actions
can still be specified at port-level and it has the same effect of
specifying the action for all devices on the port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the DMA blacklisting of the CDB-intr devices
from ata_check_atapi_dma() to ata_dma_blacklisted(), where it makes more sense.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
vt8251 chokes on NCQ commands. Two different disks from different
vendors are showing the same symptom and it seems that the windows
driver from via doesn't support NCQ either. Disable NCQ support on
this controller for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Aalderd Bouwman <boac@wanadoo.nl>
Cc: Bastiaan Jacques <b.jacques@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers
used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA
hardreset instead of SRST. This patch makes all the converted drivers
use the standard bmdma error handler which uses both SRST and SATA
hardreset.
All the controllers should be able to perform SRST but still needs
verification. If some of the controllers can't do SRST, it will be
very easy to spot as it will show up during boot probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert sata_via to new EH. vt6420 used ATA_FLAG_SRST while vt6421
used ATA_FLAG_SATA_RESET. This difference seems to be an accident
rather than intended. This patch makes both flavors use
ata_bmdma_error_handler() which makes use of both SRST and SATA
hardreset. This behavior change is intended and if it breaks
anything, it should be very easy to spot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We don't need to use the heavier spin lock in the irq handler.
It's quite possible we can do this in nv_generic_interrupt() as well,
but I didn't take the time to pursue that train of thought.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
nf2/3 and ck804 have irq status register. Implement better irq
handler for those flavors of nv. This patch makes different flavors
of nv controllers use different irq handlers by using separate
port_info for each flavor.
This change also makes following EH and hotplug updates easier to
integrate.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify interrupt constants and make NFORCE3 equal to NFORCE2.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
nv_host_desc and nv_host are used to discern different generations of
nv controllers. Kill those. New EH/hotplug implementation will use
standard port_info/ata_port_operations for that.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_nv contained hotplug code which is mainly for demonstrating how
hotplug event is handled. This patch kills the demo code in
prepration for real hotplug implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing a full ata_busy_sleep() seems to get suspend and resume working
fine on the Apple Mac Mini, at least.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one's quite tricky. The 53c700 uses the now deprecated fields of
the command structure for saving the prior command when it does
autosense. To fix this, we have to add extra fields to the LUN to
accommodate a copy of the real command.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updates:
- don't bypass SYNCHRONIZE_CACHE command
- return SCSI_MLQUEUE_HOST_BUSY when no free request slots
- move scsi_remove_host() to the begin of hpt_remove(), or it will
not work after resources being released.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Spelling correction, orphaned comment removal & update branch name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Some of the cards product names changed.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
clear_user return is 0 for success, the code fragment is written to
assume that it is the count of the number of bytes zero'd.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a hold over from the end device/expander conversion. Apparently
the rphy list pointer is never initialised, so list_del() on the
uninitialised pointer can panic the system
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For a legacy ATA controller, libata registers two separate host sets.
There was no connection between the two hosts making it impossible to
traverse all ports related to the controller. This patch adds
host_set->next which points to the second host_set and makes
ata_pci_remove_one() remove all associated host_sets.
* On device removal, all ports hanging off the device are properly
detached. Prior to this patch, ports on the first host_set weren't
detached casuing oops on driver unloading.
* On device removal, both host_sets are properly freed
This will also be used by new power management code to suspend and
resume all ports of a controller. host_set/port representation will
be improved to handle legacy controllers better and this host_set
linking will go away with it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on timing, ata_scsi_dev_rescan() might encounter a device
which is enabled but not yet attached to sdev. On such cases, the
original code caused oops. This patch makes ata_scsi_dev_rescan()
rescan only device which are attached to sdevs.
While at it, properly indent leading comment and add description about
how it's synchronized with sdev attach/detach.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SIEN on some 3112 controllers doesn't mask SATA IRQ properly. IRQ
stays asserted even after SIEN is masked and IRQ is acked. Also, even
while frozen, any SATA PHY event including hardreset raises SATA IRQ.
Clearing SError seems to be the only way to deassert SATA IRQ.
This patch makes sil_host_intr() clear SError on SATA IRQs and ignore
SATA IRQs reported while frozen so that hardreset doesn't trigger
hotplug event (which ends up hardresetting again).
In such cases, the port still gets re-frozen to minimize the danger of
screaming interrupts. This results in one nil EH repeat on
controllers with broken SIEN but other than that does no harm.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EH_REVALIDATE should be cleared after all devices on the target
port have been revalidated. Fix ata_eh_revalidate_and_attach()
accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Short-circuit interrupt handling if BMDMA2 is reported as 0xffffffff
indicating device removal.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Setup nbytes in ata_sg_init_one to the total transfer length
of the command. This is needed by some HBAs that need to know
the total transfer length of each command.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock,
which can lead to all sorts of interesting scenarios.
This whole error-handling portion of sata_mv is nasty (and will get fixed for
the new EH stuff), but for now this patch will help keep it on life-support.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pdc_adma use libata-core PIO path but were left out
during ->data_xfer conversion. Initialize with proper callbacks.
This patch is against the current libata-dev#ALL. Controllers which
implement their own PIO HSM (ahci and sil24) don't need ->data_xfer, so the
above two are the only drivers which were left out during conversion.
From: "Barry K. Nathan" <barryn@pobox.com>
Signed-off-by: Barry K. Nathan <barryn@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The RQ_SCSI_* flags are a vestiage of a long past history. The EH code
still sets them but we never make use of that information. The other
users is pluto.c which never had a chance to work but needs to be kept
compiling to keep Davem happy, so copy over the definition there.
We could probably get rid of RQ_ACTIVE/RQ_INACTIVE aswell with some
work, there's only two more or less bogus looking uses in ubd and scsi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is really just a belt and braces test. The standards require
disks to respond DT not capable on a non-LVD bus ... however, not all
disks follow the standards ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Read the transciever register and display in the host transport
properties. I'm still not entirely sure what this does for multiple
transciever adapters (like some 160 ones) however, I suspect it
displays the transciever state of the switchable bus segment.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial pass at converting the gdth driver away from the scsi_request
interface so that the request interface can be removed post 2.6.18
without breaking gdth. Based on changes from Christoph Hellwig
<hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes all the leading whitespace kconfig now warns about.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions. Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH. Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch( originally submitted by Christoph Hellwig) removes
instance_lock and changes fw_outstanding variable data type to
atomic_t.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We can race and misset the suspend bit if iscsi_write_space is
called then iscsi_send returns with a failure indicating
there is no space.
To handle this this patch returns a error upwards allowing xmitworker
to decide if we need to try and transmit again. For the no
write space case xmitworker will not retry, and instead
let iscsi_write_space queue it back up if needed (this relies
on the work queue code to properly requeue us if needed).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from davidw@netapp.com:
remove task type should return a task on success.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from davidw@netapp.com:
We must grab the session lock when modifying the running lists.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.
STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_lib.c: properly count the number of pages in scsi_req_map_sg()
[SCSI] scsi_transport_sas: make write attrs writeable
[SCSI] scsi_transport_sas; fix user_scan
[SCSI] ppa: fix for machines with highmem
[SCSI] mptspi: reset handler shouldn't be called for other bus protocols
[SCSI] Blacklist entry for HP dat changer
The calculation of nr_pages in scsi_req_map_sg() doesn't account for
the fact that the first page could have an offset that pushes the end
of the buffer onto a new page.
Signed-off-by: Bryan Holty <lgeek@frontiernet.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ops->probe_init() gone, no user is left in libata-core.c. Move
ata_do_reset() to libata-eh.c and make it static.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all drivers implementing new EH are converted to new probing
mechanism, ops->probe_reset doesn't have any user. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert to new probing mechanism and add hotplug support by enabling
PORT_IRQ_PHYRDY_CHG, marking ehi for hotplug and scheduling EH on
PORT_IRQ_PHYRDY_CHG or PORT_IRQ_DEV_XCHG.
Sil3124/32 family of controllers don't have any mechanism to wait for
the first D2H FIS after hotplug, so ATA_FLAG_SKIP_D2H_BSY is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert to new probing mechanism and add hotplug support by enabling
PORT_IRQ_PHYRDY, marking ehi for hotplug and scheduling EH on
CONNECT/PHYRDY interrupts.
Unfortunately, ahci cannot reliably wait for the first D2H FIS after
hotplug. It sometimes succeeds but times out more often than not, so
ATA_FLAG_SKIP_D2H_BSY is used.
This patch also fixes ahci_hardreset() such that D2H Register FIS RX
area is cleared before issuing COMRESET. Without this,
ata_busy_sleep() after COMRESET might prematually finish if the
previous TF contains DRDY && !BSY.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert to new probing mechanism and add hotplug support by enabling
SATA IRQ for SError.N, marking ehi for hotplug and scheduling EH on
SATA IRQs.
Sil3112/3512/3114 family of controllers use COMRESET as TF clearing
point and can reliably wait for D2H FIS after COMRESET whether the FIS
is the first D2H FIS after POR or in response to the COMRESET. Thus,
setting ATA_FLAG_HRST_TO_RESUME is enough for device detection after
hotplug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert ata_piix to new probing mechanism. Automatic hotplug is not
supported due to hardware limitation (no PHY event interrupt), but
warm plugging works.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update unload unplug - driver unloading / PCI removal. This is done
by ata_port_detach() which short-circuits EH, disables all devices and
freezes the port. With this patch, EH and unloading/unplugging are
properly synchronized.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement bootplug - boot probing via hotplug path. While loading,
ata_host_add() simply schedules probing and invokes EH. After EH
completes, ata_host_add() scans and assicates them with SCSI devices.
EH path is slightly modified to handle this (e.g. no autopsy during
bootplug). The SCSI part is left in ata_host_add() because it's
shared with legacy path and to keep probing order as before (ATA scan
all ports in host_set then attach all).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement warmplug. User-initiated unplug can be detected by
hostt->slave_destroy() and plug by transportt->user_scan(). This
patch only implements the two callbacks. The next function will hook
them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement SCSI part of hotplug.
This must be done in a separate context as SCSI makes use of EH during
probing. SCSI scan fails silently if EH is in progress. In such
cases, libata pauses briefly and retries until every device is
attached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement ATA part of hotplug. To avoid probing broken devices over
and over again, disabled devices are not automatically detached. They
are detached only if probing is requested for the device or the
associated port is offline. Also, to avoid infinite probing loop,
Each device is probed only once per EH run.
As SATA PHY status is fragile, devices are detached only after it has
used up its recovery chances unless explicitly requested by LLDD or
user (LLDD may request direct detach if, for example, it supports cold
presence detection).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement ata_eh_detach_dev(). This function is responsible for
detaching an ATA device and offlining the associated SCSI device
atomically so that the detached device is not accessed after ATA
detach is complete.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Use phy debouncing instead of unconditional wait after DEV_RST and
make sil24_hardreset() to request followup SRST as that's the only way
to wait for !BSY. Note that the original implementation never worked
- if the cached status was !BSY, ata_busy_sleep() finished
immediately; otherwise, it timed out regardless of the actual device
status.
Signed-off-by: Tejun Heo <htejun@gmail.com>
PORT_PRB is a misnomer as the area also contains other stuff. Rename
it to PORT_LRAM and add PORT_LRAM_SLOT_SZ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
The DMA complete bit of these controllers reflects ATA IRQ status
while no DMA command is in progress. So, we can tell whether the
controller is raising an interrupt or not in deterministic manner.
This patch gives sata_sil its own interrupt handler which behaves much
better than the original one in terms of error detection and handling.
This change is also necessary for later hotplug support.
Further improvements are possible, in both 2 and 4 ports versions, we
can get all status with only one readl and using custom bmdma
operations can further cut down register accesses.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_hsm_move() will be used by LLDDs which depend on standard PIO HSM
but implement their own interrupt handlers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
In some cases, hardreset must be followed by SRST.
* some controllers can't classify with hardreset
* some controllers can't wait for !BSY after hardreset (LLDD should
explicitly request followup softreset by returning -EAGAIN)
* (later) PM needs SRST w/ PMP==15 to operate after hardreset
To handle above cases, this patch implements follow-up softreset.
After a hardreset, ata_eh_reset() checks whether any of above
conditions are met and do a follow-up softreset if necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With hotplug, every reset might be a probing reset and thus something
similar to probe_init() is needed. prereset() method is called before
a series of resets to a port and is the counterpart of postreset().
prereset() can tell EH to use different type of reset or skip reset by
modifying ehc->i.action.
This patch also implements ata_std_prereset(). Most controllers
should be able to use this function directly or with some wrapping.
After hotplug, different controllers need different actions to resume
the PHY and detect the newly attached device. Controllers can be
categorized as follows.
* Controllers which can wait for the first D2H FIS after hotplug.
Note that if the waiting is implemented by polling TF status, there
needs to be a way to set BSY on PHY status change. It can be
implemented by hardware or with the help of the driver.
* Controllers which can wait for the first D2H FIS after sending
COMRESET. These controllers need to issue COMRESET to wait for the
first FIS. Note that the received D2H FIS could be the first D2H
FIS after POR (power-on-reset) or D2H FIS in response to the
COMRESET. Some controllers use COMRESET as TF status
synchronization point and clear TF automatically (sata_sil).
* Controllers which cannot wait for the first D2H FIS reliably.
Blindly issuing SRST to spinning-up device often results in command
issue failure or timeout, causing extended delay. For these
controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT
(currently 8s) to give newly attached device time to spin up, then
issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT
is not critical. libata will retry. So, the timeout needs to be
long enough to spin up most devices.
LLDDs can tell ata_std_prereset() which of above action is needed with
ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags
are PHY-specific property and will be moved to ata_link later.
While at it, this patch unifies function typedef's such that they all
have named arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With hotplug, PHY always needs to be debounced before a reset as any
reset might find new devices. Extract PHY waiting code from
sata_phy_resume() and extend it to include SStatus debouncing. Note
that sata_phy_debounce() is superset of what used to be done inside
sata_phy_resume().
Three default debounce timing parameters are defined to be used by
hot/boot plug. As resume failure during probing will be properly
handled as errors, timeout doesn't have to be long as before.
probeinit() uses the same timeout to retain the original behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
It's best to run ATA hotplug from EH but attaching SCSI devices needs
working EH. ata_aux_wq is used to give SCSI hotplug operations a
separate context.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add device persistent field dev->sdev and store the attached SCSI
device. With hotplug, libata needs to know the attached SCSI device
to offline and detach it, but scsi_device_lookup() cannot be used
because libata will reuse SCSI ID numbers - dead but not gone devices
(due to zombie opens, etc...) interfere with the lookup.
dev->sdev doesn't hold reference to the SCSI device. It's cleared
when the SCSI device goes away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add ap->hw_sata_spd_limit and initialize it once during the boot
initialization (or driver load initialization). ap->sata_spd_limit is
reset to ap->hw_sata_spd_limit on hotplug. This prevents spd limits
introduced by earlier devices from affecting new devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out ata_find_dev() and __ata_scsi_find_dev() from
ata_scsi_find_dev(). These will be used by later hotplug
implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Lifetimes of some fields span over device plugging/unplugging. This
patch moves such persistent fields to the top of ata_device and
separate them with ATA_DEVICE_CLEAR_OFFSET. Fields above the offset
are initialized once during host initializatino while all other fields
are cleared before hotplugging. Currently ->ap, devno and part of
flags are persistent.
Note that flags is partially cleared while holding host_set lock.
This is to synchronize with later warm plug implementation which will
record hotplug request in dev->flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move initialization of struct ata_device into ata_dev_init() in
preparation for hotplug. This patch calls ata_dev_init() from
ata_host_init() and thus makes no functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement ata_eh_wait(). On return from this function, it's
guaranteed that the EH which was pending or in progress when the
function was called is complete - including the tailing part of SCSI
EH. This will be used by hotplug and others to synchronize with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Set ata_device->pio_mode to XFER_PIO_0 after a successful reset. This
is to keep EH resets consistent with probe resets as updated by the
commit b6079ca409. Note that, with
soon-to-follow hotplug update, EH resets will include probe resets.
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch sets the prerequisites for the new debugging scheme that more or
less resembles Donald Becker's net driver example. This one liner doesn't
change any functionality beside setting the appropriate debug level for the
msg_enable control in the ata_port struct, which will be later used by the
ata_msg_* macros to control the amount of debug information sent to printk.
Signed-off-by: <petkov@uni-muenster.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Okay, just to sum things up.
This forces libata to wait for up to 2 seconds for BUSY|DRQ to clear
on resume before continuing.
[jgarzik adds...] During testing we never saw DRQ asserted, but
nonetheless (a) this works and (b) testing for DRQ won't hurt.
Signed-off-by: Mark Lord <liml@rtr.ca>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
max_id now means the maximum number of ids on the bus, which means it
is one greater than the largest possible id number.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi_scan_host_selected() should return -EINVAL when the id is equal
to the max_id. Currently it uses ">" when comparing with max_id, and
hence leaves the border case when "id==max_id".
The channel and lun have values valid from 0 up to,
and including, max_channel or max_lun. But, the valid values for id
range from 0 to max_id-1. This patch fixes the problem.
Signed-off-by: Amit Arora <aarora@in.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We need to pass the device in order to do per device checks such as
32bit I/O enables. With the changes to include dev->ap we now don't have
to add parameters however just clean them up. Also add data_xfer methods
to the existing drivers except ata_piix (which is in the other block of
patches). If you reject the piix one just add a data_xfer to it...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The upstream tree has the ATA_DFLAG_PIO bug fixed but does not have the
pass throuugh bug fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the pio_mode is always setup. Don't do any setup on the controller b
just ensure the mode reporting is valid to avoid tons of special cases
in PATA driver code when mode switching on the fly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Backport the "pio flush" from the libata major update to 2.6.17 for via atapi.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Relax the lowmem bounce buffer requirement for imm so that any
low memory page will do -- they don't need to be below the
ISA 16 MB limit, just need to be mapped in low memory.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Semantic changes in ISP24xx firmware behaviour inadvertently
caused the driver to believe an F-port topology was present in an
N_port-to-N_port configuration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify and centralise buffer allocation/deallocation, as
there's no point in having two memory request methods.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expandind on the previous commit:
commit 79f89a4296
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800
[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.
and given:
- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.
it's time now to remove the state-machine logic from mainline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In qla2x00_reset_chip the driver first takes the hardware lock,
and then later on takes the mbx lock.
In the mailbox_command code.. it goes the other way around.
Discovered with the lock validator.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If firmware image is unavailable via request_firwmare(), then
attempt to load the image (likely out-of-date) stored in flash
memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ISP24XX and ISP54XX parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do not flush queues then block session. This will cause commands
to needlessly swing around on us and remove goofy
recovery_failed field and replace with state value.
And do not start recovery from within the host reset function.
This causeis too many problems becuase open-iscsi was desinged to
call out to userspace then have userpscae decide if we should
go into recovery or kill the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from david.somayajulu@qlogic.com and cleaned up by Tomo.
qla4xxx is going to have a different daemon so this patch
just routes the events to the right daemon.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Discovered by steven@hayter.me.uk and patch by michaelc@cs.wisc.edu
The dtask mempool is reserving 261120 items per session! Since we are now
sending headers with sendmsg there is no reason for the mempool and that
was causing us to us carzy amounts of mem. We can preallicate a header in
the r2t and task struct and reuse them
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We only use the mtask data buffer for login tasks so we do not
need to preallocate a buffer for every mtask. This saves
8 * 31 KB.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Zhen and ported by Mike:
Don't use sendpage for the headers. sendpage for the pdu headers
does not seem to have a performance impact, makes life harder
for mutiple data pdus to be in flight and still trips up some
network cards when it is from slab mem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
The queue tracking is just not being used, not even for debugging. Information
about outstanding commands can be acquired from the scsi structures.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
A race condition existed that could result in a lost completion of a
command to the ppc based cards.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Add the ability to adjust for unusual corner case failures. Both of
these additional module parameters deal with embedded, non-intel or
complicated system scenarios.
Aif_timeout can be increased past the default 2 minute timeout to drop
application registrations when a system has an unusually high event load
resulting from continuing management requests, or simultaneous builds,
or sluggish user space as a result of system load.
Startup_timeout can be increased past the default 3 minute timeout to
drop an adapter initialization for systems that have a very large number
of targets, or slow to spin-up targets, or a complicated set of array
configurations that extend the time for the firmware to declare that it
is operational. This timeout would only have an affect on non-intel
based systems, as the (more patient) BIOS would generally be where the
startup delay would be dealt with.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Slight space and speed efficiency improvement.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Since new commands to the card are quiesced, respect the changes in
the SCSI error path which dropped locking around the hba reset handler
and similarly drop the lock requirement in the driver's path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A couple write attributes in sas transport layer have a small
bug that prevents them from being written to. Those
attributes are the link_reset and write_reset. This is due
the store field being set to NULL.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the user_scan() callback currently has the potential to identify the
wrong device in the presence of expanders. This is because it finds
the first device with a matching target_id, which might be an
expander. Fix this by making it look specifically for end devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libata implemented a feature to schedule EH without an associated EH
by manipulating shost->host_eh_scheduled in ata_scsi_schedule_eh()
directly. Move this function to scsi_error.c and rename it to
scsi_schedule_eh(). It is now an exported API for SCSI transports and
exported via new header file drivers/scsi/scsi_transport_api.h
This patch also de-export scsi_eh_wakeup() which was exported
specifically for ata_scsi_schedule_eh().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LLDDs rely on libata that certain EH actions are automatically taken
on some errors. If the port is frozen or one or more qc's have failed
with HSM violation or timeout, softreset is enforced (LLDD can ask for
storonger EH action at will). If any other error condition exists,
libata EH always revalidates.
This behavior existed in earlier revisions of new EH but lost during
development process. This patch restores it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the HSM error_mask mapping.
Changes:
- Better mapping in ac_err_mask()
- In HSM_ST_FIRST ans HSM_ST state, check ATA_ERR|ATA_DF and map it to AC_ERR_DEV instead of AC_ERR_HSM.
- In HSM_ST_FIRST and HSM_ST state, map DRQ=1 ERR=1 to AC_ERR_HSM.
- For PIO data in and DRQ=1 ERR=1, add check after the junk data block is read.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ppa cannot handle highmem pages, and like imm, which already has
this patch, the device is slow, so performance is not a big issue,
so just force pages to be in low memory (hence mapped).
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
after upgrading our SUN E250 from 2.4 to 2.6 I'm seeing following error
when the HP DDS4 DAT changer gets probed:
scsi: host 1 channel 0 id 5 lun16777216 has a LUN larger than allowed by
the host adapter
The device is connected to a symbios 875 host. I've talked to Willy
about the problem, and he asked me to try to blacklist the device
for reportlun. I did that with the patch below and it solved the
problem. It now gets properly detected:
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
Vendor: HP Model: C5713A Rev: H307
Type: Sequential-Access ANSI SCSI revision: 03
target1:0:5: Beginning Domain Validation
target1:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16)
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
target1:0:5: Domain Validation skipping write tests
target1:0:5: Ending Domain Validation
Vendor: HP Model: C5713A Rev: H307
Type: Medium Changer ANSI SCSI revision: 03
Signed-off-by: tsbogend@alpha.franken.de
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement NCQ support. Sil24 has 31 command slots and all of them are
used for NCQ command queueing. libata guarantees that no other
command is in progress when it issues an internal command, so always
use tag 0 for internal commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With NCQ, there are multiple sg tables, so pp->cmd_tbl_sg doesn't cut
it. Directly calculate sg table address from pp->cmd_tbl.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* Rename CMD_TBL_HDR to CMD_TBL_HDR_SZ as it's size not offset.
* Define MAX_CMDS and CMD_SZ and use them in calculation of other
constants.
* Define CMD_TBL_AR_SZ as product of CMD_TBL_SZ and MAX_CMDS, and use
it when calculating PRIV_DMA_SZ.
* CMD_SLOT_SZ is also dependent on MAX_CMDS but hasn't been changed
because I didn't want to change the value used by the original code
(32 commands). Later NCQ change will bump MAX_CMDS to 32 anyway and
the hard coded 32 can be changed to MAX_CMDS then.
* Reorder HOST_CAP_* flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all NCQ related stuff are in place, implement NCQ device
configuration and bump ATA_MAX_QUEUE to 32 thus activating NCQ
support.
Original implementation is from Jens Axboe.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update EH to handle NCQ. ata_eh_autopsy() is updated to call
ata_eh_analyze_ncq_error() which reads log page 10h on NCQ device
error and updates eh_context accordingly. ata_eh_report() is updated
to report SActive.
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch implements NCQ command translation and exclusion. Note
that NCQ commands don't use ata_rwcmd_protocol() to choose ATA
command. This is because, unlike non-NCQ RW commands, NCQ commands
can only be used for NCQ protocol and FUA handling is done with a flag
rather than separate command.
NCQ enabled device will have queue depth larger than one but no two
non-NCQ commands can be issued simultaneously, neither can a non-NCQ
command and NCQ commands. This patch makes ata_scsi_translate()
return SCSI_MLQUEUE_DEVICE_BUSY if such exclusion is necessary. SCSI
midlayer will retry the command later.
As SCSI midlayer always retries once a command completes, this doesn't
incur unnecessary delays and as most commands will be NCQ ones for NCQ
device, so the overhead should be negligible.
Initial implementation is from Jens Axboe and using
SCSI_MLQUEUE_DEVICE_BUSY for exclusion is suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add ap->qc_active and ap->sactive, mask of all active qcs and libata's
view of the SActive register, respectively. Also, implement
ata_qc_complete_multiple() which takes new qc_active mask and complete
multiple qcs according to the mask.
These will be used to track NCQ commands and complete them. The
distinction between ap->qc_active and ap->sactive is also useful for
later PM implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rename ap->qactive to ap->qc_allocated. This is to accomodate
addition of ap->qc_active, mask of active qcs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_scsi_translate() will need to return SCSI_ML_QUEUE_DEVICE_BUSY to
achieve exlusion between NCQ and non-NCQ commands or among non-NCQ
commands. Pass its return value upward to SCSI midlayer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* kill ata_poll_qc_complete() and implement/use ata_hsm_qc_complete()
which completes qcs in new EH compliant manner from HSM
* don't print error message from ata_hsm_move(). it's responsibility
of EH.
* kill ATA_FLAG_NOINTR usage in bmdma EH
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert sata_sil24 to new EH.
* When port is frozen, IRQ for the port is masked.
* sil24_softreset() doesn't need to mangle with IRQ mask anymore.
libata ensures that the port is frozen during reset.
* Only turn on interrupts which are handled by interrupt handler and
EH. As we don't handle SDB notify yet, turn it off. DEV_XCHG and
UNK_FIS are handled by EH and thus turned on.
* sil24_softreset() usually fails to recover the port after DEV_XCHG.
ATA_PORT_HARDRESET is used as recovery action for DEV_XCHG.
* sil24 may be invoked without any active command. e.g. DEV_XCHG irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
During multiblock PIO, multiple PIOS interrupts are generated before
qc compltion. Current code prints unnecessary message for such cases.
This is exposed when new EH slows down attached device into PIO mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert AHCI to new EH. Unfortunately, ICH7 AHCI reacts badly if IRQ
mask is diddled during operation. So, freezing is implemented by
unconditionally clearing interrupt conditions while frozen.
* Interrupts are categorized according to required action.
e.g. Connection status or unknown FIS error requires freezing the
port while TF or HBUS_DATA don't.
* Only CONNECT (reflects SErr.X) interrupt is taken into account not
PHYRDY (SErr.N), as CONNECT is better cue for starting EH.
* AHCI may be invoked without any active command. e.g. CONNECT irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert sata_sil to new EH. As these controllers have hardware
interrupt mask and are known to have screaming interrupts issues, use
hardware IRQ masking for freezing. sil_freeze() masks interrupts for
the port and sil_thaw() unmasks them. As ports are automatically
frozen before probing reset, there is no need to initialize interrupt
masks sil_init_onde(). Remove related code.
Other than freezing, sata_sil uses stock BMDMA EH routines.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement new EH. The exported interface is ata_do_eh() which is to
be called from ->error_handler and performs the following steps to
recover the failed port.
ata_eh_autopsy() : analyze SError/TF, determine the cause of failure
and required recovery actions and record it in
ap->eh_context
ata_eh_report() : report the failure to user
ata_eh_recover() : perform recovery actions described in ap->eh_context
ata_eh_finish() : finish failed qcs
LLDDs can customize error handling by modifying eh_context before
calling ata_do_eh() or, if necessary, doing so inbetween each major
steps by calling each step explicitly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
struct ata_eh_info serves as the communication channel between
execution path and EH. Execution path describes detected error
condition in ap->eh_info and EH recovers the port using it. To avoid
missing error conditions detected during EH, EH makes its own copy of
eh_info and clears it on entry allowing error info to accumulate
during EH.
Most EH states including EH's copy of eh_info are stored in
ap->eh_context (struct ata_eh_context) which is owned by EH and thus
doesn't require any synchronization to access and alter. This
standardized context makes it easy to integrate various parts of EH
and extend EH to handle multiple links (for PM).
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch implements ata_ering and uses it to define dev->ering.
ata_ering is a ring buffer which records libata errors - whether a
command was for normar IO request, err_mask and timestamp. Errors are
recorded per-device in dev->ering. This will be used by EH to
determine recovery actions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SCSI command completion path used to do some part of EH including
printing messages and obtaining sense data. With new EH, all these
are responsibilities of the EH, update SCSI command completion path to
reflect this.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update ata_exec_internal() such that it uses new EH framework.
->post_internal_cmd() is always invoked regardless of completion
status. Also, when ata_exec_internal() detects a timeout condition
and new EH is in place, it freezes the port as timeout for normal
commands would do.
Note that ata_port_flush_task() is called regardless of
wait_for_completion status. This is necessary as exceptions unrelated
to the qc can abort the qc, in which case PIO task could still be
running after the wait for completion returns.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update ata_scsi_error() for new EH. ata_scsi_error() is responsible
for claiming timed out qcs and invoking ->error_handler in safe and
synchronized manner. As the state of the controller is unknown if a
qc has timed out, the port is frozen in such cases.
Note that ata_scsi_timed_out() isn't used for new EH. This is because
a timed out qc cannot be claimed by EH without freezing the port and
freezing the port in ata_scsi_timed_out() results in unnecessary
abortion of other active qcs. ata_scsi_timed_out() can be removed
once all drivers are converted to new EH.
While at it, add 'TODO: kill' comments to old EH functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
PIO executes without holding host_set lock, so it cannot be
synchronized using the same mechanism as interrupt driven execution.
port_task framework makes sure that EH is not entered until PIO task
is flushed, so PIO task can be sure the qc in progress won't go away
underneath it. One thing it cannot be sure of is whether the qc has
already been scheduled for EH by another exception condition while
host_set lock was released.
This patch makes ata_poll_qc-complete() handle such conditions
properly and make it freeze the port if HSM violation is detected
during PIO execution.
Signed-off-by: Tejun Heo <htejun@gmail.com>
