The commit 3c6fd1f07e ("ALSA: hda: Add driver blacklist") added a
new blacklist for the devices that are known to have empty codecs, and
one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f).
However, it turned out that the very same PCI SSID is used for the
previous model that does have the valid HD-audio codecs and the change
broke the sound on it.
This patch reverts the corresponding entry as a temporary solution.
Although Zenith II and co will see get the empty HD-audio bus again,
it'd be merely resource wastes and won't affect the functionality,
so it's no end of the world. We'll need to address this later,
e.g. by either switching to DMI string matching or using PCI ID &
SSID pairs.
Fixes: 3c6fd1f07e ("ALSA: hda: Add driver blacklist")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200419071926.22683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 1c76aa5fb4 ("ALSA: hda/realtek - Allow skipping
spec->init_amp detection") changed the way to assign spec->init_amp
field that specifies the way to initialize the amp. Along with the
change, the commit also replaced a few fixups that set spec->init_amp
in HDA_FIXUP_ACT_PROBE with HDA_FIXUP_ACT_PRE_PROBE. This was rather
aligning to the other fixups, and not supposed to change the actual
behavior.
However, this change turned out to cause a regression on FSC S7020,
which hit exactly the above. The reason was that there is still one
place that overrides spec->init_amp after HDA_FIXUP_ACT_PRE_PROBE
call, namely in alc_ssid_check().
This patch fixes the regression by adding the proper spec->init_amp
override check, i.e. verifying whether it's still ALC_INIT_UNDEFINED.
Fixes: 1c76aa5fb4 ("ALSA: hda/realtek - Allow skipping spec->init_amp detection")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207329
Link: https://lore.kernel.org/r/20200418190639.10082-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Before the pci_driver->probe() is called, the pci subsystem calls
runtime_forbid() and runtime_get_sync() on this pci dev, so only call
runtime_put_autosuspend() is not enough to enable the runtime_pm on
this device.
For controllers with vgaswitcheroo feature, the pci/quirks.c will call
runtime_allow() for this dev, then the controllers could enter
rt_idle/suspend/resume, but for non-vgaswitcheroo controllers like
Intel hda controllers, the runtime_pm is not enabled because the
runtime_allow() is not called.
Since it is no harm calling runtime_allow() twice, here let hda
driver call runtime_allow() for all controllers. Then the runtime_pm
is enabled on all controllers after the put_autosuspend() is called.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200414142725.6020-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio controller does system-suspend and resume operations by
directly calling its helpers __azx_runtime_suspend() and
__azx_runtime_resume(). However, in general, we don't have to resume
always the device fully at the system resume; typically, if a device
has been runtime-suspended, we can leave it to runtime resume.
Usually for achieving this, the driver would call
pm_runtime_force_suspend() and pm_runtime_force_resume() pairs in the
system suspend and resume ops. Unfortunately, this doesn't work for
the resume path in our case. For handling the jack detection at the
system resume, a child codec device may need the (literally) forcibly
resume even if it's been runtime-suspended, and for that, the
controller device must be also resumed even if it's been suspended.
This patch is an attempt to improve the situation. It replaces the
direct __azx_runtime_suspend()/_resume() calls with with
pm_runtime_force_suspend() and pm_runtime_force_resume() with a slight
trick as we've done for the codec side. More exactly:
- azx_has_pm_runtime() check is dropped from azx_runtime_suspend() and
azx_runtime_resume(), so that it can be properly executed from the
system-suspend/resume path
- The WAKEEN handling depends on the card's power state now; it's set
and cleared only for the runtime-suspend
- azx_resume() checks whether any codec may need the forcible resume
beforehand. If the forcible resume is required, it does temporary
PM refcount up/down for actually triggering the runtime resume.
- A new helper function, hda_codec_need_resume(), is introduced for
checking whether the codec needs a forcible runtime-resume, and the
existing code is rewritten with that.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Link: https://lore.kernel.org/r/20200413082034.25166-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, when the HD-audio controller driver doesn't detect any
codecs, it tries to abort the probe. But this abort happens at the
delayed probe, i.e. the primary probe call already returned success,
hence the driver is never unbound until user does so explicitly.
As a result, it may leave the HD-audio device in the running state
without the runtime PM. More badly, if the device is a HD-audio bus
that is tied with a GPU, GPU cannot reach to the full power down and
consumes unnecessarily much power.
This patch changes the logic after no-codec situation; it continues
probing without the further codec initialization but keep the
controller driver running normally.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Tested-by: Roy Spliet <nouveau@spliet.org>
Link: https://lore.kernel.org/r/20200413082034.25166-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd-hda-intel driver handles the most of its probe task in the delayed
work (either via workqueue or via firmware loader). When an error
happens in the later delayed probe, we can't deregister the device
itself because the probe callback already returned success and the
device was bound. So, for now, we set hda->init_failed flag and make
the rest untouched until the device gets really unbound.
However, this leaves the device up running, keeping the resources
without any use that prevents other operations.
In this patch, we release the resources at first when a probe error
happens in the delayed probe stage, but keeps the top-level object, so
that the PM and other ops can still refer to the object itself.
Also for simplicity, snd_hda_intel object is allocated via devm, so
that we can get rid of the explicit kfree calls.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Link: https://lore.kernel.org/r/20200413082034.25166-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the error path of the firmware loading error, the driver tries to
release the card object and set NULL to drvdata. This may be referred
badly at the possible PM action, as the driver itself is still bound
and the PM callbacks read the card object.
Instead, we continue the probing as if it were no option set. This is
often a better choice than the forced abort, too.
Fixes: 5cb543dba9 ("ALSA: hda - Deferred probing with request_firmware_nowait()")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Link: https://lore.kernel.org/r/20200413082034.25166-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Asus FX505DT with Realtek ALC233, the headset mic is connected
to pin 0x19, with default 0x411111f0.
Enable headset mic by reconfiguring the pin to an external mic
associated with the headphone on 0x21. Mic jack detection was also
found to be working.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207131
Signed-off-by: Adam Barber <barberadam995@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410090032.2759-1-barberadam995@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent AMD platform exposes an HD-audio bus but without any actual
codecs, which is internally tied with a USB-audio device, supposedly.
It results in "no codecs" error of HD-audio bus driver, and it's
nothing but a waste of resources.
This patch introduces a static blacklist table for skipping such a
known bogus PCI SSID entry. As of writing this patch, the known SSIDs
are:
* 1043:874f - ASUS ROG Zenith II / Strix
* 1462:cb59 - MSI TRX40 Creator
* 1462:cb60 - MSI TRX40
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206543
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200408140449.22319-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The access to Analog Capture Source control value implemented in
prodigy_hifi.c is wrong, as caught by the recently introduced sanity
check; it should be accessing value.enumerated.item[] instead of
value.integer.value[]. This patch corrects the wrong access pattern.
Fixes: 6b8d6e5518 ("[ALSA] ICE1724: Added support for Audiotrak Prodigy 7.1 HiFi & HD2, Hercules Fortissimo IV")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207139
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200407084402.25589-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep control helper function blindly stores the values in two
stereo channels no matter whether the actual control is mono or
stereo. This is practically harmless, but it annoys the recently
introduced sanity check, resulting in an error when the checker is
enabled.
This patch corrects the behavior to store only on the defined array
member.
Fixes: 0401e8548e ("ALSA: hda - Move beep helper functions to hda_beep.c")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207139
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200407084402.25589-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP new platform has new mute led feature.
COEF index 0x34 bit 5 to control playback mute led.
COEF index 0x35 bit 2 and bit 3 to control Mic mute led.
[ corrected typos by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/6741211598ba499687362ff2aa30626b@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Note Book supported new mute Led.
Hardware PIN was not enough to meet old LED rule.
JD2 to control playback mute led.
GPO3 to control capture mute led.
(ALC285 didn't control GPO3 via verb command)
This two PIN just could control by COEF registers.
[ corrected typos by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/6741211598ba499687362ff2aa30626b@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audio setup on the Lenovo Carbon X1 8th gen is the same as that on
the Lenovo Carbon X1 7th gen, as such it needs the same
ALC285_FIXUP_THINKPAD_HEADSET_JACK quirk.
This fixes volume control of the speaker not working among other things.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1820196
Cc: stable@vger.kernel.org
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200402174311.238614-1-hdegoede@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
patch_realtek.c has historically failed to properly configure the PC
Beep Hidden Register for the ALC256 codec (among others). Depending on
your kernel version, symptoms of this misconfiguration can range from
chassis noise, picked up by a poorly-shielded PCBEEP trace, getting
amplified and played on your internal speaker and/or headphones to loud
feedback, which responds to the "Headphone Mic Boost" ALSA control,
getting played through your headphones. For details of the problem, see
the patch in this series titled "ALSA: hda/realtek - Set principled PC
Beep configuration for ALC256", which fixes the configuration.
These symptoms have been most noticed on the Dell XPS 13 9350 and 9360,
popular laptops that use the ALC256. As a result, several model-specific
fixups have been introduced to try and fix the problem, the most
egregious of which locks the "Headphone Mic Boost" control as a hack to
minimize noise from a feedback loop that shouldn't have been there in
the first place.
Now that the underlying issue has been fixed, remove all these fixups.
Remaining fixups needed by the XPS 13 are all picked up by existing pin
quirks.
This change should, for the XPS 13 9350/9360
- Significantly increase volume and audio quality on headphones
- Eliminate headphone popping on suspend/resume
- Allow "Headphone Mic Boost" to be set again, making the headphone
jack fully usable as a microphone jack too.
Fixes: 8c69729b44 ("ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3")
Fixes: 423cd78561 ("ALSA: hda - Fix headphone noise on Dell XPS 13 9360")
Fixes: e4c9fd10eb ("ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant")
Fixes: 1099f48457 ("ALSA: hda/realtek: Reduce the Headphone static noise on XPS 9350/9360")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/b649a00edfde150cf6eebbb4390e15e0c2deb39a.1585584498.git.tommyhebb@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Realtek PC Beep Hidden Register[1] is currently set by
patch_realtek.c in two different places:
In alc_fill_eapd_coef(), it's set to the value 0x5757, corresponding to
non-beep input on 1Ah and no 1Ah loopback to either headphones or
speakers. (Although, curiously, the loopback amp is still enabled.) This
write was added fairly recently by commit e3743f431143 ("ALSA:
hda/realtek - Dell headphone has noise on unmute for ALC236") and is a
safe default. However, it happens in the wrong place:
alc_fill_eapd_coef() runs on module load and cold boot but not on S3
resume, meaning the register loses its value after suspend.
Conversely, in alc256_init(), the register is updated to unset bit 13
(disable speaker loopback) and set bit 5 (set non-beep input on 1Ah).
Although this write does run on S3 resume, it's not quite enough to fix
up the register's default value of 0x3717. What's missing is a set of
bit 14 to disable headphone loopback. Without that, we end up with a
feedback loop where the headphone jack is being driven by amplified
samples of itself[2].
This change eliminates the update in alc256_init() and replaces it with
the 0x5757 write from alc_fill_eapd_coef(). Kailang says that 0x5757 is
supposed to be the codec's default value, so using it will make
debugging easier for Realtek.
Affects the ALC255, ALC256, ALC257, ALC235, and ALC236 codecs.
[1] Newly documented in Documentation/sound/hd-audio/realtek-pc-beep.rst
[2] Setting the "Headphone Mic Boost" control from userspace changes
this feedback loop and has been a widely-shared workaround for headphone
noise on laptops like the Dell XPS 13 9350. This commit eliminates the
feedback loop and makes the workaround unnecessary.
Fixes: e1e8c1fdce ("ALSA: hda/realtek - Dell headphone has noise on unmute for ALC236")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/bf22b417d1f2474b12011c2a39ed6cf8b06d3bf5.1585584498.git.tommyhebb@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Lenovo X1C7 machines, after we plug the headset, the rt_resume()
and rt_suspend() of the codec driver will be called periodically, the
driver can't stay in the rt_suspend state even users doen't use the
sound card.
Through debugging, I found when running rt_suspend(), it will call
alc225_shutup(), in this function, it will change 3k pull down control
by alc_update_coef_idx(codec, 0x4a, 0, 3 << 10), this will trigger a
fake key event and that event will resume the codec, when codec
suspend agin, it will trigger the fake key event one more time, this
process will repeat.
If disable the key event before changing the pull down control, it
will not trigger fake key event. It also needs to restore the pull
down control and re-enable the key event, otherwise the system can't
get key event when codec is in rt_suspend state.
Also move some functions ahead of alc225_shutup(), this can save the
function declaration.
Fixes: 76f7dec08f (ALSA: hda/realtek - Add Headset Button supported for ThinkPad X1)
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200329082018.20486-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If SND_HDA_CODEC_CA0132 is enabled, the DSP support should be enabled as
well. Disabled DSP support leads to a hanging alsa system and no sound
output on the card otherwise. Tested on:
06:00.0 Audio device: Creative Labs Sound Core3D [Sound Blaster Recon3D / Z-Series] (rev 01)
Signed-off-by: Rouven Czerwinski <rouven@czerwinskis.de>
Link: https://lore.kernel.org/r/20200329053710.4276-1-r.czerwinski@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The system in question uses ALC285, and it uses GPIO 0x04 to control its
mute LED.
The mic mute LED can be controlled by GPIO 0x01, however the system uses
DMIC so we should use that to control mic mute LED.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200327044626.29582-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have a system which has an EVGA X99 Classified motherboard. The pin
assignments for the HD Audio controller are not correct under Linux.
Windows 10 works fine and informs me that it's using the Recon3Di
driver, and on Linux, `cat
/sys/class/sound/card0/device/subsystem_{vendor,device}` yields
0x3842
0x1038
This patch adds a corresponding entry to the quirk list.
Signed-off-by: Geoffrey Allott <geoffrey@allott.email>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/a6cd56b678c00ce2db3685e4278919f2584f8244.camel@allott.email
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A headset on the desktop like Acer N50-600 does not work, until quirk
ALC662_FIXUP_ACER_NITRO_HEADSET_MODE is applied.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200317082806.73194-3-jian-hong@endlessm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix gcc warnings when -Wextra is used by using an empty do-while
block instead of <nothing>. Fixes these build warnings:
../sound/pci/korg1212/korg1212.c:674:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:708:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:730:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:853:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1013:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1035:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1052:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1066:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1087:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1094:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:1208:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../sound/pci/korg1212/korg1212.c:2360:102: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/91fb1e97-a773-5790-3f65-8198403341e1@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A headset on the laptop like ASUS B9450FA does not work, until quirk
ALC294_FIXUP_ASUS_HPE is applied.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200225072920.109199-1-jian-hong@endlessm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell desktop platform supported headset Mic.
Add pin verb to enable headset Mic.
This platform only support fixed type headset for Iphone type.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b9da28d772ef43088791b0f3675929e7@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Need to chain the THINKPAD_ACPI, otherwise the mute led will not
work.
Fixes: d2cd795c4e ("ALSA: hda - fixup for the bass speaker on Lenovo Carbon X1 7th gen")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200219052306.24935-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some code in HD-audio driver calls snprintf() in a loop and still
expects that the return value were actually written size, while
snprintf() returns the expected would-be length instead. When the
given buffer limit were small, this leads to a buffer overflow.
Use scnprintf() for addressing those issues. It returns the actually
written size unlike snprintf().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200218091409.27162-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merging the UAC2 effect unit parser improvement. As it's based on the
previous usb-audio driver fix, it was deviated from for-next branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211200739.GA12948@embeddedor
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211194403.GA10318@embeddedor
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Variable capture_flag is only ever assigned values, it is never read
and hence it is redundant. Remove it.
Addresses-Coverity ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208223443.38047-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Variable timeout is being assigned with the value 200 that is never
read, it is assigned a new value in a following do-loop. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208222756.37707-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Variable err is being assigned with a value that is never read, it is
assigned a new value in the next statement. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208222006.37376-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal page tables are little endian, hence they should be
__le32 type. This fixes the relevant sparse warning:
sound/pci/emu10k1/emu10k1_main.c:2013:51: warning: incorrect type in assignment (different base types)
sound/pci/emu10k1/emu10k1_main.c:2013:51: expected unsigned int [usertype]
sound/pci/emu10k1/emu10k1_main.c:2013:51: got restricted __le32 [usertype]
No functional changes, just sparse warning fixes.
Link: https://lore.kernel.org/r/20200206163152.6073-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal page tables are in little endian, hence they should be
__le32 type. This fixes the relevant sparse warnings:
sound/pci/via82xx.c:454:60: warning: incorrect type in assignment (different base types)
sound/pci/via82xx.c:454:60: expected unsigned int [usertype]
sound/pci/via82xx.c:454:60: got restricted __le32 [usertype]
....
No functional changes, just sparse warning fixes.
Link: https://lore.kernel.org/r/20200206163152.6073-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a final step of the cleanup series: move the HDMI ELD parser
call into update_eld() function so that we can unify the calls.
The ELD validity check is unified in update_eld(), too.
Along with it, the repoll scheduling is moved to update_eld() as well,
where sync_eld_via_acomp() just passes 0 for skipping it.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Nikhil Mahale <nmahale@nvidia.com>
Link: https://lore.kernel.org/r/20200206162804.4734-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
