The natsemi driver has a define NATSEMI_TIMER_FREQ which looks like it
controls the normal frequency of the chip poll timer but in fact only
takes effect for the first run of the timer. Adjust the value of the
define to match that used by the timer and use the define consistently.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix warnings from sparse related to shadowed variables and routines
that should be declared static.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems detected by sparse:
1. whole chunk of MAC code was for defined and never used
2. hook for running ext intr in workqueue wasn't being used
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
eHEA recovery and DLPAR functions are called seldomly. The eHEA workqueues
are replaced by the kernel event queue.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some of the easy warnings in network device drivers.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix warnings from sparse checker about shadowed definition and improperly
formatted ethtool_strings.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a cable unplug the forced flow control settings were lost
accidentally and the flow control settings fell back to the default
EEPROM determined values. This breaks for people who want to
run without fc enabled - after a cable reset the driver would
refuse to run with fc disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After an e1000 patch from Krishna Kumar <krkumar2@in.ibm.com>.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the get-nickname wireless extension actually work. Before
this patch, I could do "iwconfig eth1 nick BLAH" but "iwconfig
eth1" would have still showed "MRVL-USB8388" to me. Hey, and that
was wrong anyway, I'm on a CF card, not on USB :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes scripts/checkincludes.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* make scan debug output cleaner
* change some LBS_DEB_ASSOC messages to LBS_DEB_SCAN, which is more correct
* move helper functions together
* print function return value in the tracing code at one central location
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes three "warning: Using plain integer as NULL pointer"
sparse warnings.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some versions of gcc replace strstr() calls with a single-character `needle'
parameter by strchr() behind our back. This causes a link error if strchr() is
defined as an inline function in <asm/string.h> (e.g. on m68k):
| drivers/built-in.o: In function `libertas_parse_chan':
| linux/drivers/net/wireless/libertas/debugfs.c:209: undefined reference to `strchr'
| drivers/built-in.o: In function `libertas_parse_ssid':
| linux/drivers/net/wireless/libertas/debugfs.c:260: undefined reference to `strchr'
Avoid this by explicitly calling strchr() instead.
Also include <linux/string.h>, because this file calls lots of str*() routines.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-By: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write constants that are (per documentation and struct) u8
as 0x0001, use 0x01 instead. Also remove an useless cast.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 88w8385 chip, using SDIO interface and firmware release 5.0.11p0,
has problems when both unicast and multicast WPA keys are set in one
command. This patch ensures the keys are set independently.
The original author of this patch is Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When skb_push() is used we should memset the memory before
usage. This will prevent bugs which could occur when the
data is treated as TX descriptor.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By defining rt73usb_get_tsf to NULL we only
have 1 location that needs to be edited
when rt73usb_get_tsf can be enabled again.
This also reduces the number of #ifdefs in
the code which is also a "good thing"
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorganize configuration handling by creating a extra
structure which contains precalculated values based
on the mac80211 values which are usefull for all
individual drivers.
This also fixes the preamble configuration problem,
up untill now preamble was never configured since
by default the rate->val value was used when changing
the mode.
Now rate->val will only be used to set the basic rate mask.
The preamble configuration will now be done correctly
through the erp_ie_changed callback function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some small optimizations by removing
some simple if-statements.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Directly pass a value from the enum dev_state with rt2x00lib_toggle_rx,
this will save us a ? : statement, and it is clearer then passing a 1 0
argument.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX datalen must always be converted to a value rt73 and rt2500usb
understand. Both require to use a different size then skb->len.
First off this is required because the descriptor must be added,
but the second is because the value must be a multiple of either 2 or 4,
and it should not be a multiple of the USB packetmax
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci contained 1 line of 88 characters width,
this needs to be cut down.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_duration expects all speeds to be passed in 100kbs,
this means that passing 2 is incorrect and should be raised to 20
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All drivers use the same values for TSF sync,
this will move the value determination into rt2x00config.c,
and the definition for the values to rt2x00reg.h
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Modestas Vainius, enabling rkfill in 1 driver and
disabling it in a second could cause a NULL pointer exception when
the rfkill-disabled driver still sets the CONFIG_SUPPORT_HW_BUTTON flag.
Furthermore, rfkill expects the timeout as a value in milliseconds
instead of jiffies. Also increase the timeout to a second,
since this 250ms would be overkill.
Also the flag DEVICE_ENABLED_RADIO_HW is causing problems
for devices which do not support the hardware button
while rfkill is enabled in the driver.
To remidy this we should inverse the flag and its meaning,
rename the flag to DEVICE_DISABLED_RADIO_HW this means that
by default the radio is enabled by the hardware button (if present)
and can only be disabled explicitely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't use changed_flags when configuring the packet filter,
we work directly with the total_flags which is safe enough since
we already check if something has changed after we applied our
packet filtering flag rules.
Also make sure that when the packet filter is scheduled, the
rt2x00dev->interface.filter is cleared to make sure the drivers
will update the packet filter instead of failing at the check:
*total_flags == rt2x00dev->interface.filter
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By putting the flags into a enumeration we can
make it easier maintable since we don't have to
assign numbers for each flag. This makes it easier
to insert and remove flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store the started state into a new flag DEVICE_STARTED_SUSPEND
and set this when suspending while the device was started.
We can't check for is_interface_present() since only mac80211
knows if there are monitor interfaces present.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't check if the radio is enabled in rt2x00lib_toggle_rx,
this is required since the link tuner should be disabled
when shutting down the device. The remaining calls inside the
rt2x00lib_toggle_rx handler should deliver no problems when
called while the radio is done.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various drivers contained duplicate code to handle the
MAC and BSSID initialization correctly. This moves the
address copy to little endian variables to rt2x00config.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the device ID for the HP wireless print kit usb dongle.
Thanks to Thierry Merle for the patch to the original rtl8187 driver.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 makes extensive use of background scanning when unassociated or
down. Unfortunately, the firmware sends scan completed events many
times per second, which the driver pushes directly up to userspace.
This needlessly wakes up processes listening for wireless events many
times per second. Batch together scan completed events for
non-user-requested scans and send them up to userspace every 4 seconds.
Scan completed events resulting from an SIOCSIWSCAN call are pushed up
without delay.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Su-Jong You
zd1211b chip 0471:1237 v4810 high 00-12-bf AL2230_RF pa0 g--N
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the net namespaces many code leaved the __init section,
thus making the kernel occupy more memory than it did before.
Since we have a config option that prohibits the namespace
creation, the functions that initialize/finalize some netns
stuff are simply not needed and can be freed after the boot.
Currently, this is almost not noticeable, since few calls
are no longer in __init, but when the namespaces will be
merged it will be possible to free more code. I propose to
use the __net_init, __net_exit and __net_initdata "attributes"
for functions/variables that are not used if the CONFIG_NET_NS
is not set to save more space in memory.
The exiting functions cannot just reside in the __exit section,
as noticed by David, since the init section will have
references on it and the compilation will fail due to modpost
checks. These references can exist, since the init namespace
never dies and the exit callbacks are never called. So I
introduce the __exit_refok attribute just like it is already
done with the __init_refok.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I recently noticed that when calling:
# ethtool -s eth0 autoneg on
on a 5722 (though I'm sure it's not specific to that card) that
subsequent checks of the cards status looked like this:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: No <---- This seems odd?!?
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
I noticed that the following commit:
commit 3600d918d8
Author: Michael Chan <mchan@broadcom.com>
Date: Thu Dec 7 00:21:48 2006 -0800
[TG3]: Allow partial speed advertisement.
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
changed things around so that ethtool speed settings were strictly
followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to). I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.
Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot. This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a kernel oops triggered by the ksdazzle SIR driver.
We need more space for input frames, and 2048 should be plenty of it.
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer products change the way the ASIC revision is obtained. This patch
implements how the driver will extract the revision number.
This patch also adds preliminary CPMU support. CPMU stands for Central
Power Management Unit. The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A merge/cleanup code accidentally dropped 8254x code in and removed
8257x code here. Undo this mistake and use the pci-e relevant register
test similar as to what is in e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A small bug crawled in the -DDEBUG enabled code. Fix this to
properly call the backreference device name.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debugging statements are added for inbound packets with unknown
header id. Those packets are discarded and no longer processed as
osn-packets.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the lcs irq routine detects channel failures it drives device recovery.
After this event the device is no longer usable for shutdown requests,
because the lcs_irq routine may get wrong channel status information.
In such a case the lcs_irq routine marks the channel in 'error' state.
The channel state comes back to 'running' after restarting the channels.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
if qeth_set_multicast_list() is performed on 2 CPUs in parallel,
card->ip_list may end corrupted.
Solution: In function __qeth_delete_all_mc()
remove card->ip_list entry before invoking
qeth_deregister_addr_entry(). Thus a 2nd invocation of
qeth_set_multicast_list() cannot try to remove the
same entry twice.
Signed-off-by Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix filling the qdio buffers in EDDP mode.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HiperSockets infrastructure (layer-3 mode) supports only IPv4 or
IPv6 packets. Sending other packet types disturbs TCP/IP on z/VM,
which issues messages about invalid packets.
Qeth send routine will detect packet type on sending over a
HiperSockets interface (in layer-3 mode) and drop non IP packets.
The error and drop count of the interface is incremented.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With cleanup suggestions and bugs spotted by Stephen Hemminger,
Ingo Oeser, Matheos Worku, and Oliver Hartkopp.
Signed-off-by: David S. Miller <davem@davemloft.net>
pasemi_mac: enable iommu support
Enable IOMMU support for pasemi_mac, but avoid using it on non-partitioned
systems for performance reasons.
The user can override this by selecting the PPC_PASEMI_IOMMU_DMA_FORCE
configuration option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I've tried to compile 2.6.23-rc8-mm2, but it fails on ipg.c with the
error : ERROR: "__udivdi3" [drivers/net/ipg.ko] undefined!
I've instigated a bit, and I've found this code in ipg.c :
static void ipg_nic_txfree(struct net_device *dev)
{
struct ipg_nic_private *sp = netdev_priv(dev);
void __iomem *ioaddr = sp->ioaddr;
const unsigned int curr = ipg_r32(TFD_LIST_PTR_0) -
(sp->txd_map / sizeof(struct ipg_tx)) - 1;
unsigned int released, pending;
sp->txd_map is an u64
because :
dma_addr_t txd_map;
And in asm-i386/types.h, I see :
#ifdef CONFIG_HIGHMEM64G
typedef u64 dma_addr_t;
#else
typedef u32 dma_addr_t;
#endif
I my config, I use CONFIG_HIGHMEM64G
sizeof(struct ipg_tx) is an u32
So the div failed on i386 because of u64 / u32.
[akpm@linux-foundation.org: cleanups]
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: use buffer index pointer in clean_rx()
Use the new features in B0 for buffer ring index on the receive side. This
means we no longer have to search in the ring for where the buffer
came from.
Also cleanup the RX cleaning side a little, while I was at it.
Note: Pre-B0 hardware is no longer supported, and needs a pile of other
workarounds that are not being submitted for mainline inclusion. So the
fact that this breaks old hardware is not a problem at this time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: clear out old errors on interface open
Clear out any pending errors when an interface is brought up. Since the bits
are sticky, they might be from interface shutdown time after firmware has
used it, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: update todo list
Remove some stale todo items that have been taken care of. Add a couple
of upcoming ones.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: further performance tweaks
Misc driver tweaks for pasemi_mac:
* Increase ring size (really needed mostly on 10G)
* Take out an unneeded barrier
* Move around a few prefetches and reorder a few calls
* Don't try to clean on full tx buffer, just let things
take their course and stop the queue directly
* Avoid filling on the same line as the interface is
working on to reduce cache line bouncing
* Avoid unneeded clearing of software state (and make the
interface shutdown code handle it)
* Fix up some of the tx ring wrap logic.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: add local skb alignment
Add local SKB alignment to pasemi_mac, since ppc64 in general has it at 0
because of design flaws in some of the IBM server bridge chips. However,
for PWRficient doing the unaligned copies is more expensive than doing
unaligned DMA so make sure the data is aligned instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: workaround for erratum 5971
Implement workarounds for erratum 5971, where L2 hints aren't considered
properly unless the way hint is enabled on the interface. Since L2 isn't
setup to dedicate a way to headers, we need to reset the packet count
by hand so it won't run out of credits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: implement sg support
Implement SG support for pasemi_mac
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: rework ring management
Rework ring management, switching to an opaque ring format instead of
the struct-based descriptor+pointer setup, since it will be needed for
SG support.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: fix bug in receive buffer dma mapping
skb->len isn't actually set to the size of the allocated skb, so don't
try to use it when figuring out how much to map.
(This hasn't surfaced as a real bug because we effectively disable
translation for the interface, but it still needs fixing for the future)
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: basic error checking
Add some rudimentary error checking to pasemi_mac.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement much easier and more lightweight locking for
the periodic work.
This also removes the last big busywait loop and replaces it
by a sleeping loop.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full support for the RFKILL button and
the RFKILL LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drive the LEDs through the generic LED triggers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel now provides a generic hexdump implementation should we need
it again, so we can remove it from zd1211rw. After removing that, only
one single-user function is left in zd_util. Move that to zd_mac and
remove zd_util.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As detailed at https://bugs.gentoo.org/159646 hostap with hostapd confuses
udev by presenting 2 interfaces with the same MAC address. Also, at the time
of detection, the 'type' attribute is 1, identical to other hostap interfaces.
The AP interface is supposed to have type ARPHRD_IEEE80211 (801), but this is
not set until after registration.
Setting it before register_netdev() is called allows us to avoid this
confusion. We can do this by propogating the HOSTAP_INTERFACE type through
to hostap_setup_dev().
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow up to the patches from Denys Vlasenkos
<vda.linux@googlemail.com> to further optimize firmware loading.
1. In bnx2_init_cpus(), we allocate memory for decompression once
and use it repeatedly instead of doing this for every firmware image.
2. We eliminate the BSS and SBSS firmware sections in bnx2_fw*.h since
these are always zeros.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
this are the changes to the smc911x driver, which were necessary
to get it running on the Magic Panel R2 (smsc9115).
It is a SH3-DSP based board. The other patches are available on
the linuxsh-dev mailinglist.
http://marc.info/?l=linuxsh-dev&r=1&b=200708&w=2
It was necessary to set the irq sense to low level.
Therefor the SMC_IRQ_SENSE define was added.
How are the chances for inclusion in 2.6.24?
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Due to stability issues in high load situations the HW queue handling
has to be changed. The HW queues are now stopped and restarted again instead
of destroying and allocating new HW queues.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, bitbanged MDIO was only supported in individual
hardware-specific drivers. This code factors out the higher level
protocol implementation, reducing the hardware-specific portion to
functions setting direction, data, and clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The existing OF glue code was crufty and broken. Rather than fix it, it
will be removed, and the ethernet driver now talks to the device tree
directly.
The old, non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM
platforms are dropped from arch/ppc (which will hopefully be soon), and
existing arch/powerpc boards that I wasn't able to test on for this
patchset get converted (which should be even sooner).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At least some hardware driven by this driver needs receive buffers
to be aligned on a 16-byte boundary. This usually happens by chance,
but it breaks if slab debugging is enabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These macros accomplish nothing other than defeating type checking.
This patch also fixes one instance of the wrong register size being
used that was revealed by enabling type checking.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies gzip unpacking code in bnx2 driver so that
it does not depend on bnx2 internals. I will move this code
out of the driver and into zlib in follow-on patch.
It can be useful in other drivers which need to store firmwares
or any other relatively big binary blobs - fonts, cursor bitmaps,
whatever.
Patch is run tested by Michael Chan (driver author).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the 93cx6 eeprom code to the ax88796 driver and modify the ax88796
driver to read out the mac address from the eeprom. We need this for the
ax88796 on certain SuperH boards. The pin configuration used to connect
the eeprom to the ax88796 on these boards is the same as pointed out by the
ax88796 datasheet, so we can probably reuse this code for multiple
platforms in the future.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the PHY_HALTED state is not entered with the IRQ asserted as it
could lead to an interrupt loop.
There is a small window in phy_stop(), where the state of the PHY machine
indicates it has been halted, but its interrupt output might still be
unmasked. If an interrupt goes active right at this moment it will loop as
the phy_interrupt() handler exits immediately with IRQ_NONE if the halted
state is seen. It is unsafe to extend the phydev spinlock to cover
phy_interrupt(). It is safe to swap the order of the actions though as all
the competing places to unmask the interrupt output of the PHY, which are
phy_change() and phy_timer() are already covered with the lock as is the
sequence in question.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.
Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved. As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt. Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.
I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state. This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().
While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary. OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.
Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Log "no link during initialization" at KERN_INFO as it's not an error, and
occurs every time the interface comes up (when the forcedeth-phy-power-down
patch is applied).
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use spin_lock_bh()/spin_unlock_bh() for the phydev lock throughout as it
is used in phy_timer() that is called as a softirq and all the other
operations may happen in the user context.
There has been a change recently that did such a conversion for some of the
operations on the lock, but some have been left intact. Many of them,
perhaps all, may be called in the user context and I was able to trigger
recursive spinlock acquisition indeed, so I think for the sake of long-term
maintenance it is best to convert them all, even if unnecessarily for one
or two -- better safe than sorry.
Perhaps one in phy_timer() could actually be skipped as only called as a
softirq -- I can send an update if that sounds like a good idea.
Checked with checkpatch.pl and at the runtime.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes an apparent potential null dereference bug where we
dereference dev before a null check. This patch simply remvoes the
can't-happen test for a null pointer.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In xl_freemem(), if dev_if is NULL, the line
struct xl_private *xl_priv =(struct xl_private *)dev->priv;
will cause a NULL pointer dereference.
(akpm: don't try to fix it: just delete the pointless test-for-null)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes dead code ("tx_xcnt" can never be != 0 at this place)
spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface. Reading and setting those valuse doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
device_bind_driver() error code returning has been fixed. release()
function has been written, so that to free resources in correct way; the
release path is now clean.
Before the rework, it used to cause
Device 'fixed@100:1' does not have a release() function, it is broken
and must be fixed.
BUG: at drivers/base/core.c:104 device_release()
Call Trace:
[<ffffffff802ec380>] kobject_cleanup+0x53/0x7e
[<ffffffff802ec3ab>] kobject_release+0x0/0x9
[<ffffffff802ecf3f>] kref_put+0x74/0x81
[<ffffffff8035493b>] fixed_mdio_register_device+0x230/0x265
[<ffffffff80564d31>] fixed_init+0x1f/0x35
[<ffffffff802071a4>] init+0x147/0x2fb
[<ffffffff80223b6e>] schedule_tail+0x36/0x92
[<ffffffff8020a678>] child_rip+0xa/0x12
[<ffffffff80311714>] acpi_ds_init_one_object+0x0/0x83
[<ffffffff8020705d>] init+0x0/0x2fb
[<ffffffff8020a66e>] child_rip+0x0/0x12
Also changed the notation of the fixed phy definition on
mdio bus to the form of <speed>+<duplex> to make it able to be used by
gianfar and ucc_geth that define phy_id strictly as "%d:%d" and cleaned up
the whitespace issues.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Document the fact that atl1 uses a single shared register for the high 32
bits of 64-bit DMA addresses, making 64-bit DMA more trouble than it's worth.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Per Al's suggestion, get rid of the stupid stuff:
Remove cam_type switch,
And deinline things that aren't important for speed.
And make big macro and inline.
And remove some dead/unused code.
And use const char * for chip name.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The via-velocity is using a non-standard VLAN interface configured
via module parameters (yuck).
Replace with the standard acceleration interface.
It solves a number of problems with being able to handle multiple
vlans, and dynamically reconfigure.
This is compile tested only, don't have this board.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver model and phylib update. It includes the following changes:
1. Removal of unused module options.
2. Phylib support and the resulting removal of generic bits for handling
the PHY.
3. Proper reserving of device resources and using ioremap()ped handles
to access MAC registers rather than platform-specific macros.
4. Handling of the device using the driver model.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove typedefs, volatiles and convert kmalloc()/memset() pairs to
kcalloc(). Also reformat the surrounding clutter.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Returning BUSY will make qdisc_restart enqueue the skb which was already
freed. The bad skb was correctly freed and we should return NETDEV_TX_OK.
First spotted by Jeff Garzik on 08/13/07.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up redundant PHY write line for ULi526x Ethernet
Driver.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.
In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market. We would like to request that this not be
> included.
Since the product never reached market, clearly nobody is using this orphaned
driver.
Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: pass in count of buffers to replenish rx ring with
Refactor replenish_rx_ring to take an argument for how many entries to
fill. Since it's normally available from where it's called anyway, this
is just simpler. It also removes the awkward logic to try to figure out
if we're filling for the first time or not.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: don't enable rx before there are buffers on the ring
Reorder initialization of the DMA channels and the interface. Before there
was a time window when the interface was enabled before DMA was enabled.
Also, now there will always be RX buffers available at the time the
MAC interface is enabled, to avoid temporary out-of-buffer errors for the
very first packets (on busy networks).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: flags as passed to spin_*_irqsave() should be unsigned long.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: set interface speed correctly on XAUI ports
Set interface speed for XAUI to 10G per default, not 1G.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the stats member of struct netdevice in IPoIB, so we can save
memory by deleting the stats member of struct ipoib_dev_priv, and save
code by deleting ipoib_get_stats().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A hint as to why it is safe to use per cpu variables,
and note that we actually can have multiple instances
of the loopback device now.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rates scale statistics to debugfs:
$ cat /sys/kernel/debug/ieee80211/phy<X>/stations/<mac>/rate_stats_table
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds fixed rate setting through debugfs
$ echo <rate_n_flags> > \
/sys/kernel/debug/ieee80211/phy<X>/stations/<mac>/rate_scale_table
Currently there is no way to turn to rate scaling working again.
Will be fixed in later.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up rs_rate_scale_perform function. It removes dead
code, shortens variable names and removes useless return i.e. function
now returns void.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds supp_rate bit mask to rate scale sta private data structre
and thus removes sta from the argument list in helper functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch change printouts on TX path to the net_ratelimit version.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds read rate scale table debugfs function for 4965
rate scaling module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds debugfs handler to rate scale algorithms.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes redundant memset in rate scale. In rs_alloc_sta,
kzalloc is used so the memset can be avoided. In rs_rate_init, it is
a bug fix since it overrides everything set in other handlers namely
add_debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few Firmware errors reported the most reproducible
http://bughost.org/bugzilla/show_bug.cgi?id=1471
The root cause is rate_n_flags isn't set anymore. This patch fixes
the problem.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes tiny typo in 4965 rate sacling algorithm
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clears stations table for every rxon command.
It removes iwl_rxon_add_station function in 3945.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes out sending beacon from conditional in
config_ap function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch repaces IPW with IWL in error messages.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interface up/down detection was incorrectly changed during the filter API
update.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_status_irqsafe can handle the freeing of all TXed frames.
Also, set excessive_retries for failed frames.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to load the revision ourselves anymore.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to pollute dmesg with copyright info.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac address write is broken for big endian and the bssid write can be
simplified. This patch does both.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looping in the interrupt handler is unnecessary.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_hw.config indicates that the radio
is enabled and is configuring options that require
the link tuner to be restarted the link tuner will
cause a kernel panic when rfkill has indicated the
radio was in fact disabled.
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Modestas Vainius the link tuner
could continue working while the radio is already
down. This because at the start of disable_radio
the ENABLED_RADIO flag is cleared and causes the
toggle_rx to skip the stop_link_tuner() call.
This will add a check to the start of the link tuner
which will automatically stop the link tuner when the
radio is disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling cancel_delayed_work_sync() unconditionally won't hurt
and it will avoid race conditions when another CPU is already
executing link_tuner work.
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loosely based on the patch by Matthijs Kooijman,
this will add the dev_flags entry into debugfs which
will display rt2x00dev->flags.
This will allow easier debugging of flag handling.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00dev->flags has become a chaos over time,
this will reorganize the flags by renaming, deleting, adding
and properly implement the flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently rt2561s actually has PCI ID 0x0301
and rt2561 actually has PCI ID 0x0302.
Where rt2561s supports Turbo.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By increasing the timeout for rt2x00usb_vendor_request,
we should limit the number of loops required to send
a signal to the device succefully.
500ms timeout is specified by the Ralink legacy drivers
for rt2500usb. For rt73usb 1000ms is specified, but that
includes the timeout for the firmware which is already
specified in a different define.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make rt61pci_beacon_update and rt73usb_beacon_update static,
they are only used inside their own source file and then only
for setting it as callback funtion for mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to rt2x00lib_precalculate_link_signal resets link.rx_success
which is needed when calculating the average rssi for the link
tuner. Change the call order so the link tuner runs first as it
doesn't need the result of the precalculate.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The typedef is not required, we can just use "enum ieee80211_key_alg"
instead of "ieee80211_key_alg"
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loopback device is special. It should be initialized at the very
beginning. Initialization order has been changed by
Eric W. Biederman <ebiederm@xmission.com> and this change is non-obvious
and important enough to add proper comment.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids user confusion when they see that their device is not detected.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pasemi_mac.c: At top level:
drivers/net/pasemi_mac.c:89: warning: 'read_iob_reg' defined but not used
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/spider_net_ethtool.c: In function 'spider_net_get_ethtool_stats':
drivers/net/spider_net_ethtool.c:160: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:161: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:162: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:163: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:164: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:165: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:166: error: structure has no member named 'netdev_stats'
make[2]: *** [drivers/net/spider_net_ethtool.o] Error 1
Also do another ARRAY_SIZE() cleanup while at it.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for dynamically allocating the statistics counters
for the loopback device and adds appropriate device methods for allocating
and freeing the loopback device.
This completes support for creating multiple instances of the loopback
device, in preparation for creating per network namespace instances.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing memory alignment problems on the blackfin architecture (maybe on the
ARM also)
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve two bytes to align pointer to the IP header.
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes the tx transmit timeout problem, which is
caused by the interrupts being incorrectly check and masked. The patch
moves the interrupt masking code so that interrupts are enabled only
when the driver is registered and only disabled when the driver is
unregistered.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects a minor bug with priv->dnld_sent being set incorrectly in
if_cs_host_to_card.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up the radio-related messages in several ways.
(1) The state of the rfkill switch is assumed to be on, rather than
tested. Now, any user without such a switch will not see any
messages. For devices with such a switch, a message will be
logged only if the initial state is off, or if the switch is toggled.
(2) The routine for testing the switch state is no longer inline.
(3) The LED handling routine is simplified.
(4) The "Radio turned off" message that has confused some users has been
changed to "Radio initialized".
This patch is patterned after a similar change to b43 by Michael Buesch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
This patch is based on a similar patch of b43 by Michael Buesch.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message is useless. Only report state changes.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cleanup the code a bit and remove the inline.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes all Sparse warnings in SSB.
No semantics change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a PCI bus use ioreadX() and iowriteX().
We map the I/O space with pci_iomap(), so we must use the correct
accessor functions, too.
readX() and writeX() are not guaranteed to accept the cookie returned
from pci_iomap() (though, it currently works on most architectures).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not required and the txpower adjustment must not be in atomic.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinhard Speyerer reported at 2007-08-10 a new device.
Here are the information strings.
Product: Telegent TG54USB WLAN Adapter
USB ID: 129b:1666
Chip ID: zd1211 chip 129b:1666 v4330 high 00-01-36 RF2959_RF pa0 -----
FCC ID: N89-UW620Z
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some distros ship bcm43xx with debugging printout disabled. For those
BCM43xx devices with radio on/off switches, this makes it impossible
to know if the radio is on or off. This patch changes a pair of debug
printk's into ordinary printk's. It also changes the message that
prints when the radio is initialized to the off state as the old message
seems to confuse users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to initialize to NULL when variable is never used before
it's assigned the return value of a kmalloc() call.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing this makes loopback.c a better example of how to do a
simple network device, and it removes the special case
single static allocation of a struct net_device, hopefully
making maintenance easier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: we still have several fishy areas - mcast filter
and vlan handling.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
amd8111e_calc_coalesce() ends up with insane values of tx_data_rate since
->tx_bytes increments missing conversion from little- to host-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Layout of opts2 is
: MSB(vlan_tag) : LSB(vlan_tag) : flags : 0 :
regardless of the host endianness. On little-endian
the current code ends up with the right values, but
on big-endian it blows. In r8169.c the same bug
had been fixed in commit d35da12a40426184b1d0844104b1d464753eba19
(r8169: endianness fixes).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SB1250 network interfaces are Gigabit Ethernet ones. Move the
Kconfig entry to the appropriate section and add some help text.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since we are adding requirement for the PHYLIB for this driver, there should be a select for that
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- add MDIO functions and register mdio bus
- add phy abstraction layer (PAL) functions and use PAL API
- test on STAMP537 board
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alex Landau writes in the forums:
Previously, changing the MAC address (e.g. via ifconfig) resulted
in a generic function to be called that only changed a variable in
memory. This patch also updated the Blackfin MAC address registers
to filter the correct new MAC.
Signed-off-by: Alex Landau <lirsb@yahoo.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Update transceiver information in ethtool function
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
- Converted the macro to a function and removed call to memset
- regarding function naming convention, for all callbacks and entry points
will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.
[ Move driver into it's own directory -DaveM ]
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
register instead of de asserting by clearing the source of interrupts with
multiple writes which causes loss of interrupts (race conditions). It is
entirely possible that before the driver has a chance to mask the asserted
alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
this case Herc will keep the INTA line asserted and the bridge will not
send a new Assert_INTA message upstream.
[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added check to return from the traffic handling function, if the card status
is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
Packets containing corrupted data will be dropped (not transmitted) or tagged
as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
(undesirable PCI behaviour)is tagged as a "serious error". In such cases
the adapter will give up its ability to be a bus master. In this situation
the host will still be able to read internal device registers in order to
generate an error report. A device reset is necessary to return to normal
operation.
- In the event of a pcix data parity error, the adapter will automatically
disable itself. Adapter_En will automatically transition from '1' to '0' and
the adapter will enter its clean-up routine. Once the device has achieved
quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.
[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
"unsigned long long *" but the function takes a "u64 *" which is
different on many 64-bit platforms. -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to unmask entire set of device errors and alarams.
Alarm interrupts are generated for a myriad of purposes, ranging from
illegal operations or requests to internal state machine errors and
uncorrectable data corruption errors. In several cases the adapter can
recover gracefully from unexpected events; however, in some cases, a device
reset may be necessary. This patch handles alarms generated by all the
blocks within the device.
The adapter generates the following types of alarms:
1. Link state transitions (local/remote fault) or other link-related
problems.
2. Problems with any device peripherals, including the EEPROM, FLASH,
etc.
3. Correctable ECC errors (single-bit errors) on internal data
structures or frame data.
4. Uncorrectable ECC errors (multi-bit errors) on internal data
structures or frame data.
5. State machine errors, which indicate that internal control
structures have become corrupted.
6. PCI related errors, including parity errors or illegal transactions.
7. Other unexpected events.
- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
duplicate codes.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
remove setup platform device from jazzsonic, which is done in arch code now
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sgiseeq driver is one of the few remaining users of the ancient
cache banging DMA API. Replaced with the modern days DMA API.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, the driver only tries up to 5 times (5us) to get the results
of a CQ context operation. Testing has shown the chip can take as much
as 50us to return the response on SG_CONTEXT_CMD operations. So we up
the retry count to 100 to cover high loads.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The cxgb3 driver is incorrectly configuring the HW CQ context for CQ's
that use overflow-avoidance. Namely the RDMA control CQ. This results
in a bad DMA from the device to bus address 0. The solution is to set
the CQ_ERR bit in the context for these types of CQs.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Qualify toggling of xgmac tx enable with not getting pause frames,
we might not make forward progress because the peer is sending
lots of pause frames.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear pciE PEX errors late at module load time.
Log details when PEX errors occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update firmware version.
Allow the driver to be up and running with older FW image
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since E100 timer is 2HZ, use rounding to make timer occur on the
correct boundary.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the workaround that was needed for PS3 firmware versions
prior to the first release.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
