This patch adds support for the realtek 8211c phy. The driver must
perform a hardware reset of the phy due to an errata where the phy could
not detect the link.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless statistics produced by the RTL8187B driver are not particularly
informative about the strength of the received signal. From the data sheet
provided by Realtek, I discovered that certain parts of the RX header
should have the information necessary to calculate signal quality and
strength. With testing, it became clear that most of these quantities were
very jittery - only the AGC correlated with the signals expected from nearby
AP's. As a result, the quality and strength are derived from the agc value.
The scaling has been determined so that the numbers are close to those
obtained by b43 under the same conditions. The results are qualitatively
correct.
Statistics derived for the RTL8187 have not been changed.
The RX header variables have been renamed to match the quantites described
in the Realtek data sheet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix TX sequence numbers" broke rtl8187. This
patch makes the same kind of fix that was done for rt2x00. Note that
this code will have to be reworked for proper sequence numbers on beacons.
In addition, the sequence number has been placed in the hardware state,
not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/mac80211_hwsim.c:503:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)
We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.
However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.
To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.
This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.
In rt2x00 the value was
( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us
This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: Olivier Cornu <o.cornu@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is a nice thing, but we cannot enable it without changing the
interrupt handler. If we do it, we break MSI capable hardware,
specifically AR5006 chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_beacon_update takes sc->lock upon entry. However, it is only
called from within ath5k_config_interface, which already holds the lock.
Remove the unnecessary locking from ath5k_beacon_update.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-scan.o
drivers/net/wireless/iwlwifi/iwl-scan.c: In function 'iwl_rx_scan_complete_notif':
drivers/net/wireless/iwlwifi/iwl-scan.c:274: warning: unused variable 'scan_notif'
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-led.c: In function 'iwl_led_brightness_set':
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: 'led_type_str' undeclared (first use in this function)
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: (Each undeclared identifier is reported only once
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: for each function it appears in.)
The problem is that led_type_str is defined under CONFIG_IWLWIFI_DEBUG
while IWL_DEBUG is a static inline function in this case. Replace it
with macro.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some persistent settings were using hex and others decimal. In some cases,
values were set in hex but reported in decimal. Confusing.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building the wireless-next-2.6 tree with CONFIG_IWL3945 (for building
iwl-3945 driver) and where CONFIG_IWL3945_LEDS is not set,
we get this warning:
drivers/net/wireless/iwlwifi/iwl-3945.c: In function
'iwl3945_pass_packet_to_mac80211':
drivers/net/wireless/iwlwifi/iwl-3945.c:633: warning: unused variable 'hdr'
This patch adds #ifdef to iwl3945_pass_packet_to_mac80211() to avoid this
warning. (The variable 'hdr' is used only if CONFIG_IWL3945_LEDS is set)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helge Deller reports that HP laptops (NC4010 and NC6000) use active-
high signals to turn on the LEDs. Previous code used active-low for
all devices.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- free and re-request irq since it might have changed during suspend
- disable and enable msi
- don't set D0 state of the device, it's already done by the PCI layer
- do restore_state before enable_device, it's safer
- check ath5k_init return value
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't sync
- coherent mapping (descriptors)
- before unmap, it's useless
- (wrongly anyway -- for_cpu) beacon skb, it's just mapped,
so by the device yet
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that the irq is not in progress after stop. This means
two things:
- ensure the intr setting register is set by flushing posted values
- call synchronize_irq() after that
Also flush stop tx write, inform callers of the tx stop about still
pending transfers (unsuccessful stop) and finally don't wait another
3ms in ath5k_rx_stop, since ath5k_hw_stop_rx_dma ensures transfer to
be finished.
Make sure all writes will be ordered in respect to locks by mmiowb().
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to kill tasklets on stop to not panic if they
fire after freeing some structures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When signal is noisy, hardware can use all RX buffers and since the last
entry in the list is self-linked, it overwrites the entry until we link
new buffers.
Ensure that we don't free this last one until we are 100% sure that it
is not used by the hardware anymore to not cause memory curruption as
can be seen below.
This is done by checking next buffer in the list. Even after that we
know that the hardware refetched the new link and proceeded further
(the next buffer is ready) we can finally free the overwritten buffer.
We discard it since the status in its descriptor is overwritten (OR-ed
by new status) too.
=============================================================================
BUG kmalloc-4096: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff810067419060-0xffff810067419667. First byte 0x8 instead of 0x6b
INFO: Allocated in dev_alloc_skb+0x18/0x30 age=1118 cpu=1 pid=0
INFO: Freed in skb_release_data+0x85/0xd0 age=1105 cpu=1 pid=3718
INFO: Slab 0xffffe200019d0600 objects=7 used=0 fp=0xffff810067419048 flags=0x40000000000020c3
INFO: Object 0xffff810067419048 @offset=4168 fp=0xffff81006741c120
Bytes b4 0xffff810067419038: 4f 0b 02 00 01 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a O.......ZZZZZZZZ
Object 0xffff810067419048: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object 0xffff810067419058: 6b 6b 6b 6b 6b 6b 6b 6b 08 42 30 00 00 0b 6b 80 kkkkkkkk.B0...k.
Object 0xffff810067419068: f0 5d 00 4f 62 08 a3 64 00 0c 42 16 52 e4 f0 5a 360].Ob.243d..B.R344360Z
Object 0xffff810067419078: 68 81 00 00 7b a5 b4 be 7d 3b 8f 53 cd d5 de 12 h...{245264276};.S315325336.
Object 0xffff810067419088: 96 10 0b 89 48 54 23 41 0f 4e 2d b9 37 c3 cb 29 ....HT#A.N-2717303313)
Object 0xffff810067419098: d1 e0 de 14 8a 57 2a cc 3b 44 0d 78 7a 19 12 15 321340336..W*314;D.xz...
Object 0xffff8100674190a8: a9 ec d4 35 a8 10 ec 8c 40 a7 06 0a 51 a7 48 bb 2513543245250.354.@247..Q247H273
Object 0xffff8100674190b8: 3e cf a1 c7 38 60 63 3f 51 15 c7 20 eb ba 65 30 >ϡ3078`c?Q.307.353272e0
Redzone 0xffff81006741a048: bb bb bb bb bb bb bb bb 273273273273273273273273
Padding 0xffff81006741a088: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
Pid: 3297, comm: ath5k_pci Not tainted 2.6.26-rc8-mm1_64 #427
Call Trace:
[<ffffffff802a7306>] print_trailer+0xf6/0x150
[<ffffffff802a7485>] check_bytes_and_report+0x125/0x180
[<ffffffff802a75dc>] check_object+0xac/0x260
[<ffffffff802a9308>] __slab_alloc+0x368/0x6d0
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff804b1bd4>] ? __alloc_skb+0x44/0x150
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff802aa853>] __kmalloc_track_caller+0xc3/0xf0
[<ffffffff804b1bfe>] __alloc_skb+0x6e/0x150
[... stack snipped]
FIX kmalloc-4096: Restoring 0xffff810067419060-0xffff810067419667=0x6b
FIX kmalloc-4096: Marking all objects used
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addition of an argument to dma_mapping_error() in commit
8d8bb39b9e "dma-mapping: add the device
argument to dma_mapping_error()" left a bit of fallout:
drivers/net/ibmveth.c:263: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:264: error: expected ')' before 'goto'
drivers/net/ibmveth.c:284: error: expected expression before '}' token
drivers/net/ibmveth.c:297: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:298: error: expected ')' before 'dma_unmap_single'
drivers/net/ibmveth.c:306: error: expected expression before '}' token
drivers/net/ibmveth.c:491: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: expected ')' before '{' token
drivers/net/ibmveth.c:974: error: expected expression before '}' token
drivers/net/ibmveth.c:914: error: label 'out' used but not defined m
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4: Update/add Mellanox Technologies copyright lines to mlx4 driver files
mlx4_core: Add VLAN tag field to WQE control segment struct
RDMA/nes: CM connection setup/teardown rework
IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG
IPoIB/cm: Connected mode is no longer EXPERIMENTAL
RDMA/ucm: BKL is not needed for ib_ucm_open()
RDMA/ucma: BKL is not needed for ucma_open()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (39 commits)
[PATCH] fix RLIM_NOFILE handling
[PATCH] get rid of corner case in dup3() entirely
[PATCH] remove remaining namei_{32,64}.h crap
[PATCH] get rid of indirect users of namei.h
[PATCH] get rid of __user_path_lookup_open
[PATCH] f_count may wrap around
[PATCH] dup3 fix
[PATCH] don't pass nameidata to __ncp_lookup_validate()
[PATCH] don't pass nameidata to gfs2_lookupi()
[PATCH] new (local) helper: user_path_parent()
[PATCH] sanitize __user_walk_fd() et.al.
[PATCH] preparation to __user_walk_fd cleanup
[PATCH] kill nameidata passing to permission(), rename to inode_permission()
[PATCH] take noexec checks to very few callers that care
Re: [PATCH 3/6] vfs: open_exec cleanup
[patch 4/4] vfs: immutable inode checking cleanup
[patch 3/4] fat: dont call notify_change
[patch 2/4] vfs: utimes cleanup
[patch 1/4] vfs: utimes: move owner check into inode_change_ok()
[PATCH] vfs: use kstrdup() and check failing allocation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
make it atomic_long_t; while we are at it, get rid of useless checks in affs,
hfs and hpfs - ->open() always has it equal to 1, ->release() - to 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If we can be sure that elevating the page_count on a pagecache page will
pin it, we can speculatively run this operation, and subsequently check to
see if we hit the right page rather than relying on holding a lock or
otherwise pinning a reference to the page.
This can be done if get_page/put_page behaves consistently throughout the
whole tree (ie. if we "get" the page after it has been used for something
else, we must be able to free it with a put_page).
Actually, there is a period where the count behaves differently: when the
page is free or if it is a constituent page of a compound page. We need
an atomic_inc_not_zero operation to ensure we don't try to grab the page
in either case.
This patch introduces the core locking protocol to the pagecache (ie.
adds page_cache_get_speculative, and tweaks some update-side code to make
it work).
Thanks to Hugh for pointing out an improvement to the algorithm setting
page_count to zero when we have control of all references, in order to
hold off speculative getters.
[kamezawa.hiroyu@jp.fujitsu.com: fix migration_entry_wait()]
[hugh@veritas.com: fix add_to_page_cache]
[akpm@linux-foundation.org: repair a comment]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable ibmveth for Cooperative Memory Overcommitment (CMO). For this driver
it means calculating a desired amount of IO memory based on the current MTU
and updating this value with the bus when MTU changes occur. Because DMA
mappings can fail, we have added a bounce buffer for temporary cases where
the driver can not map IO memory for the buffer pool.
The following changes are made to enable the driver for CMO:
* DMA mapping errors will not result in error messages if entitlement has
been exceeded and resources were not available.
* DMA mapping errors are handled gracefully, ibmveth_replenish_buffer_pool()
is corrected to check the return from dma_map_single and fail gracefully.
* The driver will have a get_desired_dma function defined to function
in a CMO environment.
* When the MTU is changed, the driver will update the device IO entitlement
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Activates larger rx buffer pools when the MTU is changed to a larger
value. This patch de-activates the large rx buffer pools when the MTU
changes to a smaller value.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we hack the virtio_net driver to always allocate full-sized (64k+)
skbuffs, the driver slows down (lguest numbers):
Time to receive 1GB (small buffers): 10.85 seconds
Time to receive 1GB (64k+ buffers): 24.75 seconds
Of course, large buffers use up more space in the ring, so we increase
that from 128 to 2048:
Time to receive 1GB (64k+ buffers, 2k ring): 16.61 seconds
If we recycle pages rather than using alloc_page/free_page:
Time to receive 1GB (64k+ buffers, 2k ring, recycle pages): 10.81 seconds
This demonstrates that with efficient allocation, we don't need to
have a separate "small buffer" queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Finally this patch lets virtio_net receive GSO packets in addition
to sending them. This can definitely be optimised for the non-GSO
case. For comparison the Xen approach stores one page in each skb
and uses subsequent skb's pages to construct an SG skb instead of
preallocating the maximum amount of pages per skb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (added feature bits)
This patch adds some basic ethtool operations to virtio_net so
I could test SG without GSO (which was really useful because TSO
turned out to be buggy :)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (remove MTU setting)
On Mon, 2008-05-26 at 17:42 +1000, Rusty Russell wrote:
> If we fail to transmit a packet, we assume the queue is full and put
> the skb into last_xmit_skb. However, if more space frees up before we
> xmit it, we loop, and the result can be transmitting the same skb twice.
>
> Fix is simple: set skb to NULL if we've used it in some way, and check
> before sending.
...
> diff -r 564237b31993 drivers/net/virtio_net.c
> --- a/drivers/net/virtio_net.c Mon May 19 12:22:00 2008 +1000
> +++ b/drivers/net/virtio_net.c Mon May 19 12:24:58 2008 +1000
> @@ -287,21 +287,25 @@ again:
> free_old_xmit_skbs(vi);
>
> /* If we has a buffer left over from last time, send it now. */
> - if (vi->last_xmit_skb) {
> + if (unlikely(vi->last_xmit_skb)) {
> if (xmit_skb(vi, vi->last_xmit_skb) != 0) {
> /* Drop this skb: we only queue one. */
> vi->dev->stats.tx_dropped++;
> kfree_skb(skb);
> + skb = NULL;
> goto stop_queue;
> }
> vi->last_xmit_skb = NULL;
With this, may drop an skb and then later in the function discover that
we could have sent it after all. Poor wee skb :)
How about the incremental patch below?
Cheers,
Mark.
Subject: [PATCH] virtio_net: Delay dropping tx skbs
Currently we drop the skb in start_xmit() if we have a
queued buffer and fail to transmit it.
However, if we delay dropping it until we've stopped the
queue and enabled the tx notification callback, then there
is a chance space might become available for it.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
MAINTAINERS: Remove Glenn Streiff from NetEffect entry
mlx4_core: Improve error message when not enough UAR pages are available
IB/mlx4: Add support for memory management extensions and local DMA L_Key
IB/mthca: Keep free count for MTT buddy allocator
mlx4_core: Keep free count for MTT buddy allocator
mlx4_code: Add missing FW status return code
IB/mlx4: Rename struct mlx4_lso_seg to mlx4_wqe_lso_seg
mlx4_core: Add module parameter to enable QoS support
RDMA/iwcm: Remove IB_ACCESS_LOCAL_WRITE from remote QP attributes
IPoIB: Include err code in trace message for ib_sa_path_rec_get() failures
IB/sa_query: Check if sm_ah is NULL in ib_sa_remove_one()
IB/ehca: Release mutex in error path of alloc_small_queue_page()
IB/ehca: Use default value for Local CA ACK Delay if FW returns 0
IB/ehca: Filter PATH_MIG events if QP was never armed
IB/iser: Add support for RDMA_CM_EVENT_ADDR_CHANGE event
RDMA/cma: Add RDMA_CM_EVENT_TIMEWAIT_EXIT event
RDMA/cma: Add RDMA_CM_EVENT_ADDR_CHANGE event
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: put ColdFire head code into .text.head section
m68knommu: remove last use of CONFIG_FADS and CONFIG_RPXCLASSIC
m68knommu: remove RPXCLASSIC from the m68k tree
m68knommu: fec: remove FADS
m68knommu: MCF5307 PIT GENERIC_CLOCKEVENTS support
m68knommu: add read_barrier_depends() and irqs_disabled_flags()
m68knommu: add byteswap assembly opcode for ISA A+
m68knommu: add ffs and __ffs plattform which support ISA A+ or ISA C
m68knommu: add sched_clock() for the DMA timer
m68knommu: complete generic time
m68knommu: move code within time.c
m68knommu: m68knommu: add old stack trace method
m68knommu: Add Coldfire DMA Timer support
m68knommu: defconfig for M5407C3 board
m68knommu: defconfig for M5307C3 board
m68knommu: defconfig for M5275EVB board
m68knommu: defconfig for M5249EVB board
m68knommu: change to a configs directory for board configurations
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pkt_sched: sch_sfq: dump a real number of flows
atm: [fore200e] use MODULE_FIRMWARE() and other suggested cleanups
netfilter: make security table depend on NETFILTER_ADVANCED
tcp: Clear probes_out more aggressively in tcp_ack().
e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() call
net: Update entry in af_family_clock_key_strings
netdev: Remove warning from __netif_schedule().
sky2: don't stop queue on shutdown
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although mv643xx_eth has no hardware support for inserting a vlan
tag by twiddling some bits in the TX descriptor, it does support
hardware TX checksumming on packets where the IP header starts {a
limited set of values other than 14} bytes into the packet.
This patch sets mv643xx_eth's ->vlan_features to NETIF_F_SG |
NETIF_F_IP_CSUM, which prevents the stack from checksumming vlan'ed
packets in software, and if vlan tags are present on a transmitted
packet, notifies the hardware of this fact by toggling the right
bits in the TX descriptor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When there is a link status change (link or phy status interrupt),
print a message notifying the user of the new link status.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth hardware has a provision for polling the PHY's
MII management registers to obtain the (R)(G)MII interface speed
(10/100/1000) and duplex (half/full) and pause (off/symmetric)
settings to use to talk to the PHY.
The driver currently does not make use of this feature. Instead,
whenever there is a link status change event, it reads the current
link parameters from the PHY, and programs those parameters into
the mv643xx_eth MAC by hand.
This patch switches the mv643xx_eth driver to letting the MAC
auto-determine the (R)(G)MII link parameters by PHY polling, if there
is a PHY present. For PHYless ports (when e.g. the (R)(G)MII
interface is connected to a hardware switch), we keep hardcoding the
MII interface parameters.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Instead of hardcoding MII register addresses and values, use the
symbolic constants defined in linux/mii.h.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth driver is limiting DMA bursts to 32 bytes, while
using the largest burst size (128 bytes) gives a couple percentage
points performance improvement in throughput tests, and the docs
say that the 128 byte default should not need to be changed, so
use 128 byte bursts instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The recommended sequence for waiting for the transmit path to clear
after disabling all of the transmit queues is to wait for the
TX_FIFO_EMPTY bit in the Port Status register to become set as well
as the TX_IN_PROGRESS bit to clear.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The maximum receive packet size field in the Port Serial Control
register controls at what size received packets are flagged
overlength in the receive descriptor, but it doesn't prevent
overlength packets from being DMAd to memory and signaled to the
host like other received packets.
mv643xx_eth does not support receiving jumbo frames in 10/100 mode,
but setting the packet threshold to larger than 1522 bytes in 10/100
mode won't cause breakage by itself.
If we really want to enforce maximum packet size on the receiving
end instead of on the sending end where it should be done, we can
always just add a length check to the software receive handler
instead of relying on the hardware to do the comparison for us.
What's more, changing the maximum packet size field requires
temporarily disabling the RX/TX paths. So once the link comes
up in 10/100 Mb/s mode or 1000 Mb/s mode, we'd have to disable it
again just to set the right maximum packet size field (1522 in
10/100 Mb/s mode or 9700 in 1000 Mb/s mode), just so that we can
offload one comparison operation to hardware that we might as well
do in software, assuming that we'd want to do it at all.
Contrary to what the documentation suggests, there is no harm in
just setting a 9700 byte maximum packet size in 10/100 mode, so use
the maximum maximum packet size for all modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth driver allows doing transmit reclaim from within the
napi poll routine, but after doing reclaim, it would forget to check
the free transmit descriptor count and wake up the transmit queue if
the reclaim caused enough descriptors for a new packet to become
available. This would cause the netdev watchdog to occasionally kick
in during certain workloads with combined receive and transmit traffic.
Fix this by adding a wakeup check identical to the one in the
interrupt handler to the napi poll routine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When the ethernet link goes down while mv643xx_eth is transmitting
data, transmit DMA can stop before all queued transmit descriptors
have been processed. But even the descriptors that _have_ been
processed might not be properly marked as done before the transmit
DMA unit shuts down.
Then when the link comes up again, the hardware transmit pointer
might have advanced while not all previous packet descriptors have
been marked as transmitted, causing software transmit reclaim to
hang waiting for the hardware to finish transmitting a descriptor
that it has already skipped.
This patch forcibly reclaims all packets on the transmit ring on a
link down interrupt, and then resyncs the hardware transmit pointer to
what the software's idea of the first free descriptor is. Also, we
need to prevent re-waking the transmit queue if we get a 'transmit
done' interrupt at the same time as a 'link down' interrupt, which
this patch does as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The previously merged TX hang erratum workaround ("mv643xx_eth:
work around TX hang hardware issue") assumes that TX_END interrupts
are delivered simultaneously with or after their corresponding TX
interrupts, but this is not always true in practise.
In particular, it appears that TX_END interrupts are issued as soon
as descriptor fetch returns an invalid descriptor, which may happen
before earlier descriptors have been fully transmitted and written
back to memory as being done.
This hardware behavior can lead to a situation where the current
driver code mistakenly assumes that the MAC has given up transmitting
before noticing the packets that it is in fact still currently working
on, causing the driver to re-kick the transmit queue, which will only
cause the MAC to re-fetch the invalid head descriptor, and generate
another TX_END interrupt, et cetera, until the packets in the pipe
finally finish transmitting and have their descriptors written back
to memory, which will then finally break the loop.
Fix this by having the erratum workaround not check the 'number of
unfinished descriptor', but instead, to compare the software's idea
of what the head descriptor pointer should be to the hardware's head
descriptor pointer (which is updated on the same conditions as the
TX_END interupt is generated on, i.e. possibly before all previous
descriptors have been transmitted and written back).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
Evgeniy Polyakov noticed that drivers/net/e1000e/netdev.c:e1000_netpoll()
was calling e1000_clean_tx_irq() without taking the TX lock.
David Miller suggested to remove the call altogether: since in this
callpah there's periodic calls to ->poll() anyway which will do
e1000_clean_tx_irq() and will garbage-collect any finished TX ring
descriptors.
This fix solved the e1000e+netconsole crashes i've been seeing:
=============================================================================
BUG skbuff_head_cache: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xf658ae9c-0xf658ae9c. First byte 0x6a instead of 0x6b
INFO: Allocated in __alloc_skb+0x2c/0x110 age=0 cpu=0 pid=5098
INFO: Freed in __kfree_skb+0x31/0x80 age=0 cpu=1 pid=4440
INFO: Slab 0xc16cc140 objects=16 used=1 fp=0xf658ae00 flags=0x400000c3
INFO: Object 0xf658ae00 @offset=3584 fp=0xf658af00
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an mlx4 device with default FW (which gives a UAR BAR size of 8 MB)
is used in a system with 64 KB pages, then there are only 8192/64==128
UAR pages available. However, the first 128 UAR pages are reserved
for use with event queue doorbells, so no UAR pages are available to
do anything else with, which means that the driver cannot work.
The current driver fails with a fairly cryptic "Failed to allocate
driver access region, aborting" message in this situation. Fix the
driver to detect the problem earlier and print out a clearer
description of the problem and a suggestion of how to fix it (use a
new firmware image).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
They have never been used in this port of the driver. It is has only
ever been used on the ColdFire SoC ethernet core.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This ifdefs are leftovers from the time as the driver was running
on a ppc.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
I found config FADS only in ppc/Kconfig. Bye bye relic.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is unnecessary, to stop queue and turn off carrier in shutdown
routine. With new netdev_queue this causes warnings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
netif_carrier_{on,off}() handles starting and stopping packet
flow into the driver. So there is no reason to invoke netif_stop_queue()
and netif_wake_queue() in response to link status events.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the error handling in r6040_init_one
in order not to leak resources and correcly unmap and release
PCI regions of the MAC. Also prefix printk's with the driver name
for clarity.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch bumps the release of the r6040 driver. There has been
quite some versions of it out there, but this one is the one
people should report bugs against.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows the MAC to handle the RX FIFO full
and no descriptor available interrupts. While we are at it
replace the TX interrupt with its corresponding definition.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the default waiting time of a packet, which
along with our previous r6040_rx path, was causing huge delays
with another host (160 to 230 ms).
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Define all the descriptor status the MAC can set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch completely reworks the RX path in order to be
more accurate about what is going on with the MAC.
We no longer read the error from the MLSR register instead read
the descriptor status register which reflects, the error per descriptor.
We now allocate skbs on the fly in r6040_rx, and we handle allocation
failure instead of simply dropping the packet. Remove the
rx_free_desc counter of r6040_private structure since we
allocate skbs in the RX path.
r6040_rx_buf_alloc is now removed and becomes unuseless.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We did not call napi_disabled when putting down the interface
which should be done. Finally initialize lp->dev when everything
is set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Joseph Fannin <jfannin@gmail.com> and Takashi Iwai <tiwai@suse.de>
noticed that commit 073a345c04
("mv643xx_eth: clarify irq masking and unmasking") broke the
mv643xx_eth build when NETPOLL is enabled, due to it not renaming
one instance of INT_CAUSE_EXT in mv643xx_eth_netpoll(). This patch
takes care of that instance as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework the RX buffers allocation function so that we do not
leak memory in the case we could not allocate skbs for the
RX path. Propagate the errors to the r6040_up function
where we call the RX buffers allocation function.
Also rename the r6040_alloc_txbufs function to
r6040_init_txbufs, to reflect what it really does.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a helper function which only modifies R6040 MAC registers
use it when we timeout, and on adapter initialization. Fix
the scheduling while atomic but in the timeout routine due
to the reallocation of rx/tx buffers.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a null pointer access in r6040_rx due
to lp->dev not being initialized.
Fix the TX timeouts, TX irq was not re-enabled on RX irq
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prefix all functions inside the r6040 driver with r6040 to
avoid namespace clashing.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows Windows Mobile 6 devices to be used for
tethering -- that is, used as modems. It was requested by
AdamW in kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=11119
and Mandriva kernel-discuss list. It is tested and confirmed
to work by Peterl:
http://forum.eeeuser.com/viewtopic.php?pid=323543#p323543
This patch is based on the patch in the above kernel bugzilla,
which is from the usb-rndis-lite tree.
[ dbrownell@users.sourceforge.net: misc fixes ]
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using multiple cores in the same package to handle received traffic
does not appear to provide a performance benefit. Therefore use CPU
topology information to count CPU packages and use that as the default
number of RX queues and interrupts. We rely on interrupt balancing to
spread the interrupts across packages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This avoids deadlock in case a reset is triggered during self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As recommended by Jean Delvare:
- Increase timeout to 50 ms
- Leave adapter class clear so that unwanted drivers do not probe our bus
- Use strlcpy() for name initialisation
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes e1000 driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed. This is based on the
ioport-free patch of e1000 driver from Auke Kok and Tomohiro Kusumi.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher<jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The email linux-nics@intel.com is no longer available, remove all
references.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Redefine DPRINTK macro using do while(0)
__FUNCTION__ to __func__
structs {} on separate lines
Surround negative constants with ()
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use struct e1000_hw *hw = adapter->hw; where necessary
Change macros E1000_READ_REG and E1000_WRITE_REG to er32 and ew32
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
An | in an if statement to check a bit? I think this needs to be a &.
As a result of this typo meth will always operate in promiscuous mode.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drivers were touching net queue before it has been started, so
without this patch, the drivers will potentially WARN at
net/core/dev.c:1328.
I don't have the hardware for the drivers below, so this patch is
untested, and thus should be carefully peer reviewed.
tc35815.c
au1000_eth.c
bfin_mac.c
macb.c
^ The four drivers are using phylib, they're calling netif_start_queue()
in open() callback. So trivially remove netif_tx_schedule_all().
Phylib will handle netif_carrier_*().
cpmac.c
fec_mpc52xx.c
fs_enet/fs_enet-main.c
sh_eth.c
^ The same as above, but these were also needlessly calling
netif_carrier_*() functions. So removed queue calls and also remove
carrier calls, since phylib will handle it. fs_enet-main.c also didn't
call netif_start_queue() at open(), this is fixed now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The OQO model 2 has an RTL8139 from Atheros that doesn't like MMIO.
It fails on modprobe, with a 'PCI Bus error' message.
Force it to always use polled IO.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/igb/igb_main.c:388:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove magic numbers for items that we already have
defined in the register header file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change driver version to 4.0.0. Netxen firmwares as old as
v3.4.216 are supported.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.
This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It had only couple of functions which are moved to main.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add macros for new chip revision and board configurations.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
various drivers were using the wrong APIs:
drivers/built-in.o: In function `hp_probe1':
hp.c:(.init.text+0xa280): undefined reference to `NS8390_init'
fixed via:
cd drivers/net/; sed -i 's/NS8390_/NS8390p_/g' \
$(grep -l NS8390_ $(grep 8390p.o Makefile | cut -d' ' -f3 | \
sed 's/.o$/.c/g'))
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MTT entries are allocated with a buddy allocator, which just keeps
bitmaps for each level of the buddy table. However, all free space
starts out at the highest order, and small allocations start scanning
from the lowest order. When the lowest order tables have no free
space, this can lead to scanning potentially millions of bits before
finding a free entry at a higher order.
We can avoid this by just keeping a count of how many free entries
each order has, and skipping the bitmap scan when an order is
completely empty. This provides a nice performance boost for a
negligible increase in memory usage.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ICM_ERROR firmware status code. In mapping to errnos, -ENFILE
seems closest.
This is in preparation for providing more detailed log info using
mlx4_err() in low-level driver when a non-zero status is returned.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a module parameter "enable_qos" to mlx4_core. If this param is
set, enable support for QoS in the INIT_HCA command. By default, the
parameter is set to 0 (disabled).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (49 commits)
powerpc: Fix build bug with binutils < 2.18 and GCC < 4.2
powerpc/eeh: Don't panic when EEH_MAX_FAILS is exceeded
fbdev: Teaches offb about palette on radeon r5xx/r6xx
powerpc/cell/edac: Log a syndrome code in case of correctable error
powerpc/cell: Add DMA_ATTR_WEAK_ORDERING dma attribute and use in Cell IOMMU code
powerpc: Indicate which oprofile counters to use while in compat mode
powerpc/boot: Change spaces to tabs
powerpc: Remove duplicate 6xx option in Kconfig
powerpc: Use PPC_LONG and PPC_LONG_ALIGN in lib/string.S
powerpc: Use PPC_LONG_ALIGN in uaccess.h
powerpc: Add a #define for aligning to a long-sized boundary
powerpc: Fix OF parsing of 64 bits PCI addresses
powerpc: Use WARN_ON(1) instead of __WARN()
powerpc: Fix support for latencytop
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add a sub-match id to ps3_system_bus
powerpc: Add a 6xx defconfig
powerpc/dma: Use the struct dma_attrs in iommu code
powerpc/cell: Add support for power button of future IBM cell blades
powerpc/cell: Cleanup sysreset_hack for IBM cell blades
...
Switch to ioremap_wc(). We keep the MTRR code since ioremap_wc()
will use UC_MINUS when falling back to uncachable, and thus let
the MTRR WC take precedence.
Also rename the error path better.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the wcfifo since it never gave any performance improvement.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IFF_PROMISC flag shouldn't be set or cleared by drivers, because
whether device be promisc mode is decided by how many upper layer
callers being referenced to it.
And the promisc changing feature of de4x5 ioctl is developer debug
feature, we can remove it now.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This changes vortex_prob1() to handle pci_name() now returning a
constant string.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was looking at this out of interest, but I'm in no way familiar with
the code.
Looks to me that the error handling code in mac80211_hwsim is awkward.
Which leads to it calling ieee80211_unregister_hw even when
ieee80211_register_hw failed.
The function has a for loop where it generates all simulated radios.
when something fails, the error handling will call mac80211_hwsim_free
which frees all simulated radios who's pointer isn't zero. However the
information stored is insufficient to determine whether or not the call
to ieee80211_register_hw succeeded or not for a specific radio. The
included patch makes init_mac80211_hwsim clean up the current simulated
radio, and then calls into mac80211_hwsim_free to clean up all the
radios that did succeed.
This however doesn't explain why the rate control registration failed..
build tested this, but had some problems reproducing the original
problem.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netfilter: nf_conntrack_sctp: fix sparse warnings
netfilter: nf_nat_sip: c= is optional for session
netfilter: xt_TCPMSS: collapse tcpmss_reverse_mtu{4,6} into one function
netfilter: nfnetlink_log: send complete hardware header
netfilter: xt_time: fix time's time_mt()'s use of do_div()
netfilter: accounting rework: ct_extend + 64bit counters (v4)
netlink: add NLA_PUT_BE64 macro
netfilter: nf_nat_core: eliminate useless find_appropriate_src for IP_NAT_RANGE_PROTO_RANDOM
hdlcdrv: Fix CRC calculation.
Revert "pkt_sched: Make default qdisc nonshared-multiqueue safe."
net: In __netif_schedule() use WARN_ON instead of BUG_ON
net: Improve simple_tx_hash().
pkt_sched: Remove unused variable skb in dev_deactivate_queue function.
sunhme: Remove stop/wake TX queue calls in set-multicast-list handler.
ucc_geth: do not touch net queue in adjust_link phylib callback
gianfar: do not touch net queue in adjust_link phylib callback
atl1: Do not wake queue before queue has been started.
This is a trivial patch against the hdlcdrv module that fixes its CRC
calculation. The finished CRC was overwriting the first two bytes of
each packet rather than being appended to the end.
I've tested this with 2.6.8 and 2.6.10-rc1, but hdlcdrv hasn't changed
much recently so it should work with many other kernel versions.
Signed-off-by: Micah Dowty <micah@navi.cx>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Alexander Beregalov and commentary
from Ben Hutchings.
These are totally unnecessary, in particular because this
driver's ->hard_start_xmit() handler takes the same driver
spinlock that the set-multicast-list handler uses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Alexey Dobriyan, the patch is
also tested by him and confirmed to fix the problem.
Packet flow during link state events should not be done by
waking and stopping the TX queue anyways, that is handled
transparently by netif_carrier_{on,off}().
So, remove the netif_{wake,stop}_queue() calls in the link
check code, and add the necessary netif_start_queue() call
to atl1_up().
Signed-off-by: David S. Miller <davem@davemloft.net>
