Commit Graph

592 Commits

Author SHA1 Message Date
Bartlomiej Zolnierkiewicz
15a4f943e7 ide: fix pre-EIDE SWDMA support
If the word 62 is not defined use the word 52 to get SWDMA mask
in ide_get_mode_mask().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Andi Drebes
ecea57309e drivers/ide/legacy/hd.c: Array size calculation using sizeof replaced with ARRAY_SIZE
This patch replaces an array size calculation in drivers/ide/legacy/hd.c
that was done using sizeof with the ARRAY_SIZE macro.

Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.

Signed-off-by: Andi Drebes <lists-receive@programmierforen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Robert P. J. Day
f50f9d8867 ide: remove content related to dead CONFIG_BLK_DEV_MAC_MEDIABAY config variable
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Robert P. J. Day
e71bc140c0 ide: remove references to the non-existent CONFIG_SCSI_EATA_DMA
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Robert P. J. Day
74c8f97a6c ide-cd: replace C code with call to ARRAY_SIZE() macro
Delete the unnecessary macro ARY_LEN and use ARRAY_SIZE directly.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Junio C Hamano
f3577db0c2 ide_in_drive_list(): "ALL" is not a wildcard anymore
This removes the support to treat "ALL" as a wildcard for
firmware revision.  This is made a separate patch, as it will
break out-of-tree ide drivers that feed its own table that uses
"ALL" as the wildcard to ide_in_drive_list().

Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:57 +02:00
Junio C Hamano
c2d3ce8c39 ide_in_drive_list(): accept NULL as the wildcard for firmware revision
Earlier, the matching of (model,rev) in ide-dma black/white list
handling was to consider "ALL" in the table to match any
revision.  This makes NULL to be also an accepted wildcard, and
changes the entries of tables in ide-dma.c to use NULL.

The code still accepts "ALL" as the wildcard, in order to keep
any out-of-tree ide driver that feeds its own table that uses
"ALL" as the wildcard to ide_in_drive_list() function from
breaking.

Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
6d78013bfc aec62xx: kill speedproc() method wrapper (take 2)
There's no reason to have the speedproc() method wrapper for the two quite
different chip families, so just get rid of it.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Matthias Kaehlcke
f9383c4269 ide: use mutex instead of ide_setting_sem semaphore in IDE driver
The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.

Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

--
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
1b9da32a28 aec62xx: remove init_dma() method (take 2)
Get rid of the init_dma() method (which had no particular reason to exist) by
folding it into the init_hwif() method. While at it, also perform some cleanup
in the latter method:

- get rid of the useless clearing of hwif->autodma;

- fold the serialization code into one 'if' statement;

- fold setting the drives' 'autotune' and 'autodma' fields into the single
  statements...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
b1d19db4e7 aec62xx: rework init_setup_aec6x80()
Rework init_setup_aec6x80() so that it won't rewrite the constant name strings
anymore -- in order to do this:

- in aec62xx_init_one(), pass a local copy of 'struct pci_device_id' down the
  call chain;

- change the names for in aec62xx_chipsets[] to default to AEC-6280[R];

- override the 'name' field in init_setup_aec6x80() only if bit 4 of the DMA
  status register is set.

While at it, also change the 'udma_mask' field for AEC-6x80R chips in this
function and remove the code doing the same from the init_hwif() method...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
83a6d4ab3b cmd64x: init. code cleanup
Fix two minor issues with PCI0646 chip reporting in the init_chipset() method:
"IRQ workaround enabled" message printed out not only for revision 0x01 and
"CMD646: chipset revision" printed twice (by IDE core and the driver itself).
Also, remove empty/pointless switch cases for the chips other than PCI0646,
duplicate write to the MRDMODE register when enabling interrupts and MEMORY
READ LINE cycles, and needless/misplaced initialization of the timing registers
in this method.
Switch to reading only the PCI revision ID register itself, not the whole 32
bits at its address in init_chipset() and init_hwif() methods; in addition,
get rid of the useless clearing of hwif->autodma and perform some cosmetic
style changes in the latter method.
Refactor ata66_cmd64x() by moving all the code into the 'switch' statement,
renaming/adding variables, and fixing the coding style.
While at it, finally get rid of the meaningless aliasing register #define's...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:55 +02:00
Sergei Shtylyov
2648e5d9a8 hpt366: simplify UltraDMA filtering (take 4)
Simplify UltraDMA mode filtering in the driver:

- make use of the newly introduced 'udma_mask' field of 'ide_pci_device_t' to
  set the correct hwif->ultra_mask, modifying init_setup_hpt366() to select
  the correct mask based on the chip revision;

- replace 'max_mode' field of the 'struct hpt_info' with 'max_ultra' specifying
  the maximum UltraDMA mode allowed;

- rewrite hpt3xx_udma_filter() to differ the filters based on the 'chip_type'
  field, and only use it for HPT366 and HPT370[A] where it's really necessary.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:55 +02:00
Matthias Kaehlcke
ef29888ea8 ide: use mutex instead of ide_cfg_sem semaphore in IDE driver
The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.

Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:55 +02:00
Sergei Shtylyov
c283f5dbe3 ide: make void and rename ide_dma_timeout() method
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:

- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;

- in au1xxx-ide.c, get rid of commented out printk();

- in sl82c105.c, get rid of unnecessary variables.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:54 +02:00
Sergei Shtylyov
841d2a9bf1 ide: make void and rename ide_dma_lostirq() method
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:

- in aec62xx.c, rename the method in accordance with other drivers, and get rid
  of unnecessary variables there;

- in pdc202xx_old.c, define/use 'hwif' variable;

- in sgiioc4.c, rearrange the code to call the resetproc() method directly.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:54 +02:00
Bartlomiej Zolnierkiewicz
b740d8846e serverworks: always tune CSB6
Switch the driver to always program DMA/PIO timings and set device transfer
mode instead of trusting BIOS on CSB6 controllers (libata pata_serverworks.c
driver is also doing things this way and there were no problems reported so
far).  While doing conversion I noticed that the old code had many issues:

* the code was assuming that hwif->dma_status is always valid
  (which obviously isn't true if hwif->dma_base == NULL)

* value of "(ultra_timing >> (4*unit)) & ~(0xF0)" expression wasn't checked
  to fit into udma_modes[5]

* code validating DMA timings didn't validate corresponding PIO timings

* extra CSB5 PIO register wasn't validated et all

* hwif->ide_dma_off_quietly() is always called before ide_set_dma() (which in
  turn calls hwif->speedproc() method - svwks_tune_chipset() in this case)
  so the code depending on DMA capable bit of DMA status to be set was never
  executed (=> the code was never validating DMA timings despite actually
  enabling DMA if the PIO timings were OK!)

* on resume driver dependend entirely on BIOS to restore timings and set
  transfer mode on the device

While at it:

There is no need to read PIO/MWDMA timings now so don't do it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
2007-07-09 23:17:53 +02:00
Bartlomiej Zolnierkiewicz
4660897e6c qd65xx: fix PIO mode selection
PIO4 is a maximum PIO mode supported by a driver.  Using "255" as a max_mode
argument to ide_get_best_pio_mode() could result in wrong timings being used
by a driver (for "pio" equal to 5) or OOPS (for "pio" values > 5 && < 255).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reviewed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
2007-07-08 15:21:58 +02:00
Uwe Koziolek
4c6c914e4c sis5513: adding PCI-ID
The SiS966 has one additional PCI-ID 1180.

If the chipset is using this PCI-ID, the primary channel is connected to the
first PATA-port. The secondary channel is connected to SATA-ports in IDE
emulation mode.  The legacy IO-ports are used.

The including of the PCI-ID into pata_sis is not sufficient, because the legacy
driver in drivers/ide is initialized before pata_sis.

Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-08 15:21:58 +02:00
Andrew Morton
d61bcce9c1 ide: ide_scan_pcibus(): check __pci_register_driver return value
drivers/ide/setup-pci.c: In function 'ide_scan_pcibus':
drivers/ide/setup-pci.c:879: warning: ignoring return value of '__pci_register_driver', declared with attribute warn_unused_result

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:36 +02:00
Albert Lee
8006bf56e3 ide: pdc202xx_new PLL input clock fix
Recently the PLL input clock of Promise 2027x is sometimes detected
higher than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().

This patch calls gettimeofday() to measure the time elapsed and
calculate the PLL input clock accordingly.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bahadir Balban <bahadir.balban@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:36 +02:00
Bartlomiej Zolnierkiewicz
52374f890c it821x: fix incorrect SWDMA mask
SWDMA modes are unsupported by it821x.  Attempts to tune SWDMA modes always
fail (due to sanity check in ->speedproc) and result in PIO being tuned.

* Fix incorrect SWDMA mask so core code won't try these modes and will just
  tune PIO if no other DMA modes are available.

* Bump driver version.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-03 22:28:35 +02:00
Bartlomiej Zolnierkiewicz
603a0e2c0a amd74xx: resume fix
* Driver can't skip programming transfer mode on the device in amd_set_drive()
  (similar fix has been applied to via82cxxx driver ages ago).

* While at it remove redundant warning (ide_config_drive_speed() already
  produces more valuable one).

* Bump driver version.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:35 +02:00
Sergei Shtylyov
96dcc08b0c hpt366: use correct enablebits for HPT36x
The HPT36x chips finally turned out to have the channel enable bits -- however,
badly implemented.  Make use of them despite it's probably only going to burden
the driver's code -- assuming both channels are always enabled by the HighPoint
BIOS anyway...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: michal.kepien@poczta.onet.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:35 +02:00
Sergei Shtylyov
783353b1d3 hpt366: blacklist MAXTOR STM3320620A for UltraDMA/66
Add the MAXTOR STM3320620A drive into the UltraDMA/66 mode blacklist
for the HPT36x chips.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:35 +02:00
Alan Cox
785955752f ide: Fix a theoretical Ooops case
Found by a static analyser. It is in theory possible we dereference
dev->id when it has become invalid. Re-order to avoid this.

Not needed for new-ide as we no longer support the crazy exabyte nest stuff

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:35 +02:00
Masatake YAMATO
b42fa13311 ide: never called printk statement in ide-taskfile.c::wait_drive_not_busy
Look at wait_drive_not_busy in drivers/ide/ide-taskfile.c:

    static u8 wait_drive_not_busy(ide_drive_t *drive)
    {
            ide_hwif_t *hwif = HWIF(drive);
            int retries = 100;
            u8 stat;

            /*
             * Last sector was transfered, wait until drive is ready.
             * This can take up to 10 usec, but we will wait max 1 ms
             * (drive_cmd_intr() waits that long).
             */
            while (((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) && retries--)
                    udelay(10);

            if (!retries)
                    printk(KERN_ERR "%s: drive still BUSY!\n", drive->name);

            return stat;
    }

`printk' is never called because `retries' never holds zero at the
outside of `while' loop: when `retries' holds zero at the while's loop
condition, `retries' will hold -1 at the if condition.

Signed-off-by: Masatake YAMATO <jet@gyve.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: joe@perches.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-03 22:28:34 +02:00
Rafael J. Wysocki
ce9b2b0abb Resume from RAM on HPC nx6325 broken
generic_ide_resume() should check if dev->driver is not NULL before applying
to_ide_driver() to it.  Fix that.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-16 02:24:43 +02:00
Peer Chen
c1183a3345 ide: Add the MCP73/77 support to PATA driver
Add the MCP73/MCP77 support to PATA driver.

bart: Added amd74xx_chipsets[] and amd_pci_tbl[] entries.
bart: Bumped driver version.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Cc: Alan Cox <alan@redhat.com>,
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:32 +02:00
Sergei Shtylyov
278978e953 hpt366: disallow Ultra133 for HPT374
Eliminate UltraATA/133 support for HPT374 -- the chip isn't capable of this mode
according to the manual, and doesn't even seem to tolerate 66 MHz DPLL clock...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Geller Sandor <wildy@petra.hos.u-szeged.hu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:32 +02:00
Jiri Slaby
ea30759643 ide: generic IDE PCI driver, add another device exception
generic IDE PCI driver, add another device exception

This device is char device and is grabbed by generic ide driver:
00:0b.0 Class ffff: National Semiconductor Corporation 87410 IDE (rev ff) (prog-if ff)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-

Disallow generic IDE PCI driver to grab it by adding next condition. Also
consolidate exceptions to one bigger 'switch (dev->vendor)'.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ingo Korb <ml@akana.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:31 +02:00
Lee Trager
0d2157f78d ide: HPA detect from resume
Currently when system which have HPA require HPA to be detected and
disabled upon resume from RAM or disk. The current IDE drivers do not do
this nor does libata (obviously it since it doesn't support HPA yet).

I have implemented this into the current IDE drivers and it has been
tested by many others since 7/15/2006 in bug number 6840:

	http://bugzilla.kernel.org/show_bug.cgi?id=6840

and it has been confirmed to work fine with no problems.

bart: added drv != NULL check to generic_ide_suspend()

From: Lee Trager <lt73@cs.drexel.edu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:30 +02:00
Bartlomiej Zolnierkiewicz
0380dad45e it821x: RAID mode fixes
The DMA support for RAID mode broke after:

	commit 71ef51cc17
	Author: Jens Axboe <axboe@suse.de>
	Date:   Fri Jul 28 09:02:17 2006 +0200

	    [PATCH] it821x: fix ide dma setup bug

	    Only enable dma for a valid speed setting.

	    Signed-off-by: Jens Axboe <axboe@suse.de>

	commit 0a8348d086
	Author: Jens Axboe <axboe@suse.de>
	Date:   Fri Jul 28 08:58:26 2006 +0200

	    [PATCH] ide: if the id fields looks screwy, disable DMA

	    It's the safer choice. Originally due to a bug in itx821x, but a
	    generally sound thing to do.

	    Signed-off-by: Jens Axboe <axboe@suse.de>

However it worked by pure luck before Jens' fixes: bogus ide_dma_enable()
usage in it821x driver combined with loosy check in ide_dma_verbose() allowed
the hardware to operate in DMA mode.  When these problems were fixed the DMA
support broke...

The source root for the regression turned out to be that the it821x.c code
was clearing too much of id->field_valid.  The IDE core code was using the
original value of id->field_valid to do the tuning but later DMA got disabled
in ide_dma_verbose() because of the incorrect id->field_valid fixup.  Fix it.

While at it:

* Do fixup() after probing the drives but before tuning them (which is also
  OK w.r.t. ide_undecoded_slave() fixup).  This change fixes device IDENTIFY
  data to be consistent before/after the tuning and allows us to remove extra
  re-tuning of drives from it821x_fixups().

* Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has
  DMA capable bit set (this is just to tell the IDE core that DMA is
  supported since it821x firmware takes care of DMA mode programming).

* Don't touch timing registers and don't program transfer modes on devices
  et all when in RAID mode - depend solely on firmware to do the tuning
  (as suggested by Alan Cox and done in libata pata_it821x driver).

Thanks for testing the patch goes out to Thomas Kuther.

Cc: Thomas Kuther <gimpel@sonnenkinder.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:29 +02:00
Bartlomiej Zolnierkiewicz
1abb8a8b84 serverworks: fix CSB6 tuning logic
Problem noticed by Joe Zbiciak, see

	http://kerneltrap.org/node/8252

for details.

On CSB6 the driver is using BIOS settings and not programming DMA/PIO timings
itself.  However the logic was completely broken and resulted in wrong timings
being silently allowed (instead of being corrected by the driver).

This bug would explain some data corruption/timeout issues with Serverworks
MegaIDE in RAID mode that Alan Cox has fixed recently with:

http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2074a106f52b6371885afbd714e929d60d0e3f64

For 2.6.23 we may be better off with completely switching the driver to always
programming timings (libata pata_serverworks.c driver is doing things this way
and there were no problems reported so far) but for 2.6.22 lets fix the bug
in the simplest and the least intrusive way.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:28 +02:00
Bartlomiej Zolnierkiewicz
ed84fad500 serverworks: remove crappy code
Remove crappy code noticed by Linus, see

	http://lkml.org/lkml/2007/5/23/476

for details.

While at it simplify logic a bit.

There should be no functionality changes caused by this patch.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-06-08 15:14:27 +02:00
Andrew Morton
585a2858b9 ide serverworks warning fixes
gcc-4.3:

drivers/ide/pci/serverworks.c: In function 'svwks_tune_chipset':
drivers/ide/pci/serverworks.c:176: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:190: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:211: warning: overflow in implicit constant conversion
drivers/ide/pci/serverworks.c:212: warning: overflow in implicit constant conversion

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:39 +02:00
Junio C Hamano
5a6248cac2 Match DMA blacklist entries between ide-dma.c and libata-core.c
There are a few entries in ata_device_blacklist[] in libata-core.c
marked with HORKAGE_NODMA but are missing from drive_blacklist[]
in ide-dma.c.  This patch makes the lists in sync.

Also remove a duplicated entry for "SanDisk SDP3B-64".

Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Mika Kukkonen
39c98c4212 Add two missing chipsets to drivers/ide/ide-proc.c
Compiling with '-Wswitch-enum' I noticed following:

  CC      drivers/ide/ide-proc.o
drivers/ide/ide-proc.c: In function ‘proc_ide_read_imodel’:
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_etrax100’ not handled in switch
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_acorn’ not handled in switch

How about the following patch?

Signed-off-by: Mika Kukkonen <mikukkon@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Alan Cox
2074a106f5 ide/pci/serverworks.c: Fix corruption/timeouts with MegaIDE
It turns out from customer reports to Red Hat and some PCI dumps that the
MegaIDE in RAID mode doesn't provide the drive tuning data that the
serverworks driver expects but sometimes does provide something that
fools the code.

For the RAID class case skip the oem setup and don't trust the BIOS data.
We then tune from scratch and this sorts it out. (This has been confirmed
on an afflicted IBM blade)

[libata serverworks.c never trusts the BIOS in the first place so is
accidentally immune]

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:38 +02:00
Henry Su
6c6a2a8d20 add the IDE device ID for ATI SB700
Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.

From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-24 02:42:37 +02:00
Jan Engelhardt
e0ff9cd12a Use menuconfig objects: IDE
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Alan Cox
640b31bf12 sl82c105: Switch to ref counting API
Not sure how this one got missed in the great purge some time ago but it did.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
122ab0887c ide: remove ide_use_dma()
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
3649c06e66 ide: add missing validity checks for identify words 62 and 63
Check validity of identify words 62 and 63 before using them in
ide_get_mode_mask().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
4728d546d7 ide: remove ide_dma_enable()
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Sergei Shtylyov
46cedc9b77 sl82c105: add speedproc() method and MWDMA0/1 support
Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
3c3f5d2c9f cs5530/sc1200: add ->speedproc support
* add {cs5530,sc1200}_tunepio() for programming PIO timings

* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
  transfer mode and convert {cs5530,sc1200}_config_dma() to use it

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
a01ba4011a cs5530/sc1200: DMA support cleanup
sc1200.c:

* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
  it is not needed because ->dma_off_quietly calls ->dma_host_off

* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
  open-coded variant, call it from the users of sc1200_config_dma2()

  [ there is no need to call ->dma_host_on in sc1200_config_dma() because
    core code takes care of calling ->ide_dma_on on successful execution
    of ->ide_dma_check ]

* add comment about ->tuneproc interface abuse

cs5530.c/sc1200.c:

* core code takes care of calling ->dma_off_quietly before calling
  ->ide_dma_check so there is no need to call it in ->ide_dma_check methods

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00
Bartlomiej Zolnierkiewicz
bd203b57c7 ide: use ide_tune_dma() part #2
Use ide_tune_dma() in ide-cris/it821x/pdc202xx_old/serverworks drivers.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
5fd216bbb2 cs5530/sc1200: add ->udma_filter methods
CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA.  Add {cs5530,sc1200}_udma_filter() to handle this.  This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers.  While at it bump
version numbers.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
793a97228d ide: always disable DMA before tuning it
ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted).  Fix it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
7f86723a60 pdc202xx_new: use ide_tune_dma()
* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
  as the comment states it has no real effect because these settings are
  overriden when the PIO mode is set (and for this driver ->autotune == 1
  so PIO mode is always programmed)

* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
  needed config_chipset_for_dma()

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
38ff8a74e8 alim15x3: use ide_tune_dma()
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma().  Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:43 +02:00
Bartlomiej Zolnierkiewicz
6b8cf7724b sis5513: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
  timings being programmed and possibly the data corruption (for < ATA100
  family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
  content of test1 variable was used, for ATA133 - MWDMA0 timings were used)

* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
  also cleanup this function a bit while at it

* add comment about PIO0 timings for < ATA100 family chipsets

* remove open-coded best PIO mode selection from config_art_rwp_pio(),
  it contained numerous bugs:

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

* use sis5513_tune_drive() instead of config_art_rwp_pio()
  in sis5513_config_xfer_rate() so the correct PIO mode is also set
  on drive even if the device is not IORDY/DMA capable

* config_art_rwp_pio() was always setting the best possible mode and not
  the wanted one - fix it and move ide_get_best_pio_mode() call to
  config_chipset_for_pio()

* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
  overriden by config_art_rwp_pio() for the host timings anyway + we need to
  set the same PIO mode on the device and the host

* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
  in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
  and not PIO4

* rename sis5513_tune_drive() to sis5513_tuneproc()
  and config_chipset_for_pio() to sis5513_tune_driver()

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:42 +02:00
Bartlomiej Zolnierkiewicz
9445de76c1 serverworks: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
  timings being programmed and possibly the data corruption (it seems that
  the minimum possible values were used but I lack the datasheets to be sure)

* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
  when doing PIO autotuning (pio == 255)

* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
  return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
  takes care of PIO tuning if no suitable DMA mode is found)

* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
  config_chipset_for_pio() contained numerous bugs when selecting PIO mode
  (luckily it was only used for devices limited to PIO by capabilities/BIOS):

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO0/1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

  - if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
    (XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
     was the same as if using XFER_PIO_5 => wrong PIO timings were set)

  - it was overriding drive->current_speed

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:42 +02:00
Bartlomiej Zolnierkiewicz
4fce3164b8 pdc202xx_old: rewrite mode programming code (v2)
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.

Rewrite mode programming code:

* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
  even if both devices on the channel are not DMA capable and after reset

* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
  as they need to be setup correctly also for PIO only devices, plus IORDY
  wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
  ATAPI devices

* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
  (driver sets ->autotune to 1 so PIO modes are always programmed => lower
   nibble of register A never equals 4 => "chipset_is_set" is always true)

* enable PIO mode programming for all ATAPI devices
  (it was limited to ->media == ide_cdrom devices)

* remove extra reads of registers A/B/C, don't read register D et all

* do clearing / programming of registers A/B/C in one go
  (gets rid of extra PCI config space read/write cycle)

* set initial values of drive_conf/AP/BP/CP variables to zero
  (paranoia for the case when PCI reads fail)

* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
  (ide_rate_filter() takes care of it)

* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)

* fix bitmasks for clearing bits of register B:

  - when programming DMA mode bit 0x10 of register B was cleared which
    resulted in overclocked PIO timing setting (iff PIO0 was used)

  - when programming PIO mode bits 0x18 weren't cleared so suboptimal
    timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
    and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)

* add FIXME comment about missing locking for 66MHz clock register

Also while at it:

* remove unused defines

* do a few cosmetic / CodingStyle fixes

* bump driver version

v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
  registers is used only by the debugging code so cover "drive_conf"
  PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
  (Noticed by Sergei Shtylyov)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:41 +02:00
Russell King
10bdaaa0fa [ARM] ecard: add ecardm_iomap() / ecardm_iounmap()
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards.  Convert all expansion card drivers to use them.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11 17:19:02 +01:00
Russell King
c7b87f3d50 [ARM] ecard: add helper function for setting ecard irq ops
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.

Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.

This fixes potential problems caused by drivers forgetting to
remove these hooks.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11 17:18:55 +01:00
Martin Schwidefsky
e25df1205f [S390] Kconfig: menus with depends on HAS_IOMEM.
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-05-10 15:46:07 +02:00
Linus Torvalds
3cb7396b7b Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix PIO setup on resume for ATAPI devices
  ide: legacy PCI bus order probing fixes
  ide: add ide_proc_register_port()
  ide: add "initializing" argument to ide_register_hw()
  ide: cable detection fixes (take 2)
  ide: move IDE settings handling to ide-proc.c
  ide: split off ioctl handling from IDE settings (v2)
  ide: make /proc/ide/ optional
  ide: add ide_tune_dma() helper
  ide: rework the code for selecting the best DMA transfer mode (v3)
  ide: fix UDMA/MWDMA/SWDMA masks (v3)
2007-05-09 15:41:31 -07:00
Bartlomiej Zolnierkiewicz
317a46a200 ide: fix PIO setup on resume for ATAPI devices
PIO should be restored also for ATAPI devices during resume, fix it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
6d208b39c4 ide: legacy PCI bus order probing fixes
IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.

Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question.  It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
5cbf79cdb3 ide: add ide_proc_register_port()
* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:11 +02:00
Bartlomiej Zolnierkiewicz
869c56ee9d ide: add "initializing" argument to ide_register_hw()
Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name.  Update all users of ide_register_hw()
accordingly.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
7f8f48af08 ide: cable detection fixes (take 2)
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...

* print user-friendly warning about limiting the maximum transfer speed
  to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
  also while at it cleanup eighty_ninty_three() a bit

* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
  - bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
    were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
    (please see FIXME comment in eighty_ninty_three() for more details)
  - CONFIG_IDEDMA_IVB=y/n cases were interchanged
  - check for SATA devices was missing

* remove private cable warnings from pdc_202xx{old,new} drivers now that core
  code provides this functionality (plus, in pdc202xx_new case the test could
  give false warnings for ATAPI devices because pdc202xx_new driver doesn't
  even support ATAPI DMA)

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
7662d046df ide: move IDE settings handling to ide-proc.c
* move
	__ide_add_setting()
	ide_add_setting()
	__ide_remove_setting()
	auto_remove_settings()
	ide_find_setting_by_name()
	ide_read_setting()
	ide_write_setting()
	set_xfer_rate()
	ide_add_generic_settings()
	ide_register_subdriver()
	ide_unregister_subdriver()

  from ide.c to ide-proc.c

* set_{io_32bit,pio_mode,using_dma}() cannot be marked static now, fix it

* rename ide_[un]register_subdriver() to ide_proc_[un]register_driver(),
  update device drivers to use new names

* add CONFIG_IDE_PROC_FS=n versions of ide_proc_[un]register_driver()
  and ide_add_generic_settings()

* make ide_find_setting_by_name(), ide_{read,write}_setting()
  and ide_{add,remove}_proc_entries() static

* cover IDE settings code in device drivers with CONFIG_IDE_PROC_FS #ifdef,
  also while at it cover with CONFIG_IDE_PROC_FS #ifdef ide_driver_t.proc

* remove bogus comment from ide.h

* cover with CONFIG_IDE_PROC_FS #ifdef .proc and .settings in ide_drive_t

Besides saner code this patch results in the IDE core smaller by ~2 kB
(on x86-32) and IDE disk driver by ~1 kB (ditto) when CONFIG_IDE_PROC_FS=n.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
1497943ee6 ide: split off ioctl handling from IDE settings (v2)
* do write permission and min/max checks in ide_procset_t functions

* ide-disk.c: drive->id is always available so cleanup "multcount" setting
  accordingly

* ide-disk.c: "address" setting was incorrectly defined as type TYPE_INTA,
  fix it by using type TYPE_BYTE and updating ide_drive_t->adressing field,
  the bug didn't trigger because this IDE setting uses custom ->set function

* ide.c: add set_ksettings() for handling HDIO_SET_KEEPSETTINGS ioctl

* ide.c: add set_unmaskirq() for handling HDIO_SET_UNMASKINTR ioctl

* handle ioctls directly in generic_ide_ioclt() and idedisk_ioctl()
  instead of using IDE settings to deal with them

* remove no longer needed ide_find_setting_by_ioctl() and {read,write}_ioctl
  fields from ide_settings_t, also remove now unused TYPE_INTA handling

v2:
* add missing EXPORT_SYMBOL_GPL(ide_setting_sem) needed now for ide-disk

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz
ecfd80e4a5 ide: make /proc/ide/ optional
All important information/features should be already available through
sysfs and ioctl interfaces.

Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).

While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:09 +02:00
Bartlomiej Zolnierkiewicz
29e744d088 ide: add ide_tune_dma() helper
After reworking the code responsible for selecting the best DMA
transfer mode it is now possible to add generic ide_tune_dma() helper.

Convert some IDE PCI host drivers to use it (the ones left need more work).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:09 +02:00
Bartlomiej Zolnierkiewicz
2d5eaa6dd7 ide: rework the code for selecting the best DMA transfer mode (v3)
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:08 +02:00
Bartlomiej Zolnierkiewicz
1813720723 ide: fix UDMA/MWDMA/SWDMA masks (v3)
* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
  ->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
  (alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
   filtering method - done in the next patch)

v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* piix: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:07 +02:00
Michael Opdenacker
59c51591a0 Fix occurrences of "the the "
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 08:57:56 +02:00
Paul Mackerras
02bbc0f09c Merge branch 'linux-2.6' 2007-05-08 13:37:51 +10:00
Stephen Rothwell
55b61fec22 [POWERPC] Rename device_is_compatible to of_device_is_compatible
for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-07 20:31:14 +10:00
Fabrice Aeschbacher
aa12b2842a ide-cs: recognize 2GB CompactFlash from Transcend
Without the following patch, the kernel does not automatically detect
2GB CompactFlash cards from Transcend.

Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Sergei Shtylyov
fdb0d72be4 hpt366: don't check enablebits for HPT36x
HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Bartlomiej Zolnierkiewicz
55e4dee329 ide-cris: fix ->speedproc and wrong ->swdma_mask
* fix ->speedproc to set the drive speed

* this driver doesn't support SWDMA so use the correct ->swdma_mask

* BUG() if an unsupported mode is passed to ->speedproc

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Bartlomiej Zolnierkiewicz
8e60d3762f siimage: fix wrong ->swdma_mask
This driver doesn't support SWDMA so use the correct ->swdma_mask.

While at it:

* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
  if DMA is not available config_chipset_for_pio() will be called
  by siimage_config_drive_for_dma() and if DMA is available
  config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()

* remove needless config_chipset_for_pio() wrapper

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:51 +02:00
Bartlomiej Zolnierkiewicz
0e9b4e535f it821x: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
  + incorrect base clock being set for controller in the passthrough mode

* move code limiting max PIO according to the pair device capabilities from
  config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
  applied for mode change requests coming through ->tuneproc and ->speedproc
  interfaces

* set device speed in it821x_tuneproc()

* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
  in the smart mode (so the check for pair device max PIO is done)

* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
  wrapper which does the max PIO mode check;  it worked by the pure luck
  previously, pio[4] and pio_want[4] arrays were used with index == 255
  so random PIO timings and base clock were set for the controller in the
  passthrough mode, thankfully PIO timings and base clock were corrected
  later by config_it821x_chipset_for_pio() call (but it was not called for
  PIO-only devices during resume and for user requested PIO autotuning)

* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
  as the driver sets ->autotune to 1 and ->tuneproc does the proper job now

* convert the last user of config_it821x_chipset_for_pio() to use
  it821x_tuneproc(drive, 255) and remove no longer needed function

While at it:

* fix few comments

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Bartlomiej Zolnierkiewicz
247b03f8dc pdc202xx_new: enable DMA for all ATAPI devices
There is no reason to limit DMA to ide_cdrom type devices.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Bartlomiej Zolnierkiewicz
072cdcbb7a alim15x3: PIO fallback fix
If DMA tuning fails always set the best PIO mode.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Sergei Shtylyov
826a1b6502 aec62xx: fix PIO/DMA setup issues
Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.

While at it, also:

- remove the driver's wrong claim about supporting SWDMA modes;

- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
  the task...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Sergei Shtylyov
66602c83dc cmd64x: use interrupt status from MRDMODE register (take 2)
Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Sergei Shtylyov
5826b318aa cmd64x: procfs code fixes/cleanups (take 2)
Fix several issues with the driver's procfs output:

- when testing if channel is enabled, the code looks at the "simplex" bits, not
  at the real enable bits -- add #define for the primary channel enable bit;

- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
  master drive's clock cycle resolution bit.

While at it, also perform the following cleanups:

- don't print extra newline before the first controller's dump;

- correct the chipset names (from CMDxxx to PCI-xxx)

- don't read from the registers which aren't used for dump;

- better align the table column sizes;

- rework UltraDMA mode dump code;

- remove PIO mode dump code that has never been finished;

- remove the duplicate interrupt status (the MRDMODE register bits mirror those
  those in the CFR and ARTTIM23 registers) and fold the dump into single line;

- correct the style of the ?: operators...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:50 +02:00
Sergei Shtylyov
7accbffdb8 cmd64x: add/fix enablebits (take 2)
The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
e51e2528d5 cmd64x: interrupt status fixes (take 2)
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
60e7a82f1a cmd64x: fix multiword and remove single-word DMA support
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
688a87d145 sl82c105: DMA support code cleanup (take 4)
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Sergei Shtylyov
e93df705af sl82c105: rework PIO support (take 2)
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly  simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05 22:03:49 +02:00
Stephen Rothwell
40cd3a4564 [POWERPC] Rename get_property to of_get_property: drivers
These are all the remaining instances of get_property.  Simple rename of
get_property to of_get_property.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-02 20:04:32 +10:00
Greg Kroah-Hartman
c401110186 IDE: remove rwsem use from ide-proc core
The subsystem rwsem is not used by the driver core at all, so the use of
it in the ide-proc code of it doesn't make any sense.  Perhaps a local
lock might be needed, but I do not really think so.

Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: linux ide <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 10:57:30 -07:00
Bartlomiej Zolnierkiewicz
8929fea39c ide/Kconfig: add missing range check for IDE_MAX_HWIFS
ide_hwif_to_major[] has only 10 entries as there are 10 major numbers
reserved for IDE (if somebody needs more it shouldn't be hard to fix).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-20 22:16:58 +02:00
Sergei Shtylyov
38b66f8444 hpt366: fix kernel oops with HPT302N
The driver crashes the kernel on HPT302N chips due to the missing initializer
for 'hpt302n.settings' having been unfortunately overlooked so far. :-<

Much thanks to Mike Mattie for pin-pointing the reason of crash.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-20 22:16:58 +02:00
Mark Lord
2571b16dde ide/pci/delkin_cb.c: add new PCI ID
Add PCI ID for a newer variant of cardbus CF/IDE adapter card.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-20 22:16:58 +02:00
Danny Kukawka
a7a832de9e ide: add "optical" to sysfs "media" attribute
Add "optical" to sysfs "media" attribute as already in /proc

Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-10 22:39:14 +02:00
Stuart Hayes
76ca1af10e ide: ugly messages trying to open CD drive with no media present
I get the following error messages when trying to open a CD device
(specifically, the Teac CD-ROM CD-224E) that has no media present:

hda: packet command error: status=3D0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=3D0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown

This happens when a "start stop unit" command (0x1b 0 0 0 3 0 0 0 0 0)
is sent to the drive to try to close the CD-ROM tray, but this drive
doesn't have that capability (it's a slim portable-type CD-ROM), so it
reports sense key 5 (illegal request) with asc/ascq 24/0.  This is
exactly how SFF8090i says it should respond.

But ide-cd.c (in cdrom_decode_status() ) just sees sense key 5 and spews
out an error.  It then goes on to request sense data, and
cdrom_log_sense() understands this error and doesn't log it.

The patch, for kernel 2.6.20.4, suppresses this error message.

Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-10 22:38:43 +02:00
Suleiman Souhlal
23450319e2 ide: correctly prevent IDE timer expiry function to run if request was already handled
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler). 

A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.

To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.

Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-04-10 22:38:37 +02:00
Suleiman Souhlal
513daadd15 ide: use correct IDE error recovery
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLE IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling).  The correct thing to do is issue a SRST
followed by a SET FEATURES command.  This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.

Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
  type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
  other commands (except IDENTIFY) so send SET FEATURES only if there are
  no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)

Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-03-26 23:03:20 +02:00
Albert Lee
362ebd83ad pdc202xx_new: Enable ATAPI DMA
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
  (thanks to Sergei Shtylyov for finding it) ]

These is the patch to turn on pdc202xx_new for ATAPI DMA.  When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid.  Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-03-26 23:03:19 +02:00
Patrick Ringl
b43c5f3dbe ide: cosmetic adaption of drivers/ide/Kconfig concerning SATA
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.

From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-03-26 23:03:19 +02:00