* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due the a fall-through in the switch statement, the IBSS mode got a
report for AP_RPOBE_RESPONSE change on reconfig. Change this to an AP
only notification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station. HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.
MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.
This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are currently linking the skbs by using skb->next
directly. This works, but the preferred way is to use
a struct sk_buff_head instead. That also prepares for
passing that to drivers directly.
While at it I noticed we calculate the duration for
fragments twice -- remove one of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should be instructed to enter PS AFTER
reconfiguring ASSOCIATED (in STA case) using ieee80211_bss_info_change_notify
same as it's being done in ieee80211_set_associated()
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vif might be busy while reconfiguring
(e.g. associated), so indicate BSS_CHANGED_IDLE as well.
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_probereq_get() can return NULL in
which case we should clean up & return NULL
in ieee80211_build_probe_req() as well.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some refactoring for IBSS HT.
Move HT info and capability IEs building code into separate functions.
Add function to get the channel type from an HT info IE.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers might assume sta.drv_priv is clear while
the sta is added, so clear it on reconfinguration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When suspending with all netdevs down, the device
is stopped but we still call a number of driver
callbacks that the driver might not expect. The
same happens during resume, we might call a few
callbacks without starting the driver. Fix this
by checking open_count around more things and
exiting quickly if it is 0.
Also, while at this I noticed that the coverage
class isn't reprogrammed after resume, so add
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.
The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 maintains a running average of the RSSI when a STA
is associated to an AP. Report threshold events to any driver
that has registered callbacks for getting RSSI measurements.
Implement callbacks in mac80211 so that driver can set thresholds.
Add callbacks in mac80211 which is invoked when an RSSI threshold
event occurs.
mac80211: add tracing to rssi_reports api and remove extraneous fn argument
mac80211: scale up rssi thresholds from driver by 16 before storing
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not send DS Channel parameter for directed probe requests
in order to maximize the chance that we get a response. Some
badly-behaved APs don't respond when this parameter is included.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function ieee80211_reconfig in net/mac80211/util.c contains label wake_up
which is defined unconditionally, but only used with CONFIG_PM. Gcc
warns about this when CONFIG_PM is not defined.
This patch makes the label's definition dependent on CONFIG_PM too,
eliminating the warning.
The issue was apparently introduced in git commit
eecc48000a.
Signed-off-by: Vincent Zweije <vincent@zweije.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently run this timer exactly once when
a new mac80211 device is registered, but that
is completely pointless since it will have no
work to do at all. Therefore, remove that and
also simplify some code using the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code to handle powersaving stations has a race:
when the powersave flag is lifted from a station,
we could transmit a packet that is being processed
for TX at the same time right away, even if there
are other frames queued for it. This would cause
frame reordering. To fix this, lift the flag only
under the appropriate lock that blocks TX.
Additionally, the code to allow drivers to block a
station while frames for it are on the HW queue is
never re-enabled the station, so traffic would get
stuck indefinitely. Fix this by clearing the flag
for this appropriately.
Finally, as an optimisation, don't do anything if
the driver unblocks an already unblocked station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE Std 802.11k-2008 added DS Parameter Set information element into
Probe Request frames as an optional information on 2.4 GHz band (and
mandatory, if radio measurements are enabled). This allows APs to
filter out Probe Request frames that may be received from neighboring
overlapping channels and by doing so, reduce the number of unnecessary
frames in the air. Make mac80211 add this IE into Probe Request frames
whenever the channel is known (i.e., whenever hwscan is not used).
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the TX rate set has been masked, the removed rates can also be
removed from the Supported Rates and Extended Supported Rates IEs in
Probe Request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Somebody noticed this problem, and I outlined
to them how to fix it, but haven't heard back
from them. So while I was adding the state
field I figured I could use it to fix it.
The problem, as I understand it, is that when
we go offchannel while the driver has a queue
stopped, the driver will likely start draining
the queue and then enable it while offchannel.
This in turn will enable the interface queue,
and that leads to transmitting data frames on
the wrong channel.
Fix this by keeping track of offchannel status
per interface, and not enabling the interface
queues on interfaces that are offchannel when
the driver enables a queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of ieee80211_sdata_running(),
some new code was introduced that uses netif_running()
instead. Switch all these instances over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are subqueue helpers so that we don't
need to get the TX queue and then wake/stop
it, use those helpers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, there is no need to notify the driver about QoS
changes for the monitor interface that is created. The warning
in ieee80211_bss_info_change_notify() would be hit otherwise.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.
Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is a need to restart/reconfig hw, tear down all the
aggregation queues and let the mac80211 and driver get in-sync to have
the opportunity to re-establish the aggregation queues again.
Need to wait until driver re-establish all the station information before tear
down the aggregation queues, driver(at least iwlwifi driver) will reject the
stop aggregation queue request if station is not ready. But also need to make
sure the aggregation queues are tear down before waking up the queues, so
mac80211 will not sending frames with aggregation bit set.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes memory leak in ieee80211_send_probe_req, which
is introduced in 7c12ce8b854df346388ea56d684784e3484012cf:
mac80211: use Probe Request template when sending a direct scan
The patch is against the latest wireless-test tree.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Unscheduled Automatic Power-Save Delivery (U-APSD) client support. The
idea is that the data frames from the client trigger AP to send the buffered
frames with ACs which have U-APSD enabled. This decreases latency and makes it
possible to save even more power.
Driver needs to use IEEE80211_HW_UAPSD to enable the feature. The current
implementation assumes that firmware takes care of the wakeup and
hardware needing IEEE80211_HW_PS_NULLFUNC_STACK is not yet supported.
Tested with wl1251 on a Nokia N900 and Cisco Aironet 1231G AP and running
various test traffic with ping.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit "mwl8k: handle station database update for AP's sta entry
via ->sta_notify()", mwl8k every now and then gets a command timeout
when ifconfig'ing a STA interface down. This turns out to be due to
mwl8k_stop() being called while the work queue item that was scheduled
by mwl8k_sta_notify() to remove the STA entry for the associated AP is
still queued, and the former disables interrupts so that when the
latter eventually runs, a command completion interrupt is never seen.
Fix this by changing ieee80211_stop_device() so that the workqueue is
flushed before drv_stop() is called, instead of doing it the other way
around as is done now. (As ->stop() is allowed to sleep, there isn't
any reason for drivers to queue work from within it.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mac80211 now has a separate function for creating Probe Request templates,
better to use it when sending direct Probe Requests to an AP. Only the
bssid needs to be updated in the template before sending it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the forgotten linux/wireless.h inclusion from mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we insert all user-specified IEs before the HT
IE for association, and after the HT IE for probe requests.
For association, that's correct only if the user-specified
IEs are RSN only, incorrect in all other cases including
WPA. Change this to split apart the user-specified IEs in
two places for association: before the HT IE (e.g. RSN),
after the HT IE (generally empty right now I think?) and
after WMM (all other vendor-specific IEs). For probes,
split the IEs in different places to be correct according
to the spec.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 does not propagate failed hardware reconfiguration
requests. For suspend and resume this is important due to all
the possible issues that can come out of the suspend <-> resume
cycle. Not propagating the error means cfg80211 will assume
the resume for the device went through fine and mac80211 will
continue on trying to poke at the hardware, enable timers,
queue work, and so on for a device which is completley
unfunctional.
The least we can do is to propagate device start issues and
warn when this occurs upon resume. A side effect of this patch
is we also now propagate the start errors upon harware
reconfigurations (non-suspend), but this should also be desirable
anyway, there is not point in continuing to reconfigure a
device if mac80211 was unable to start the device.
For further details refer to the thread:
http://marc.info/?t=126151038700001&r=1&w=2
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it is required that a system be
configured with no support for 40 MHz channels in
the 2.4 GHz band. Rather than imposing any such
restrictions on everybody, allow configuration a
system like that with a module parameter. It is
writable at runtime but only takes effect at the
time of the next association.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not all that useful to have the vif/sdata pointer,
we'd rather refer to the interfaces by their name.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a 32-bit machine, BIT() macro does not give the required
bit value if the bit is mroe than 31. In ieee802_11_parse_elems_crc(),
BIT() is suppossed to get the bit value more than 31 (42 (id of ERP_INFO_IE),
37 (CHANNEL_SWITCH_IE), (42), 32 (POWER_CONSTRAINT_IE), 45 (HT_CAP_IE),
61 (HT_INFO_IE)). As we do not get the required bit value for the above
IEs, crc over these IEs are never calculated, so any dynamic change in these
IEs after the association is not really handled on 32-bit platforms.
This patch fixes this issue.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 resumes, it currently first sets suspended
to false so the driver can start doing things and we can
receive frames.
However, if we actually receive frames then it can end
up starting some work which adds timers and then later
runs into a BUG_ON in the timer code because it tries
add_timer() on a pending timer.
Fix this by keeping track of the resuming process by
introducing a new variable 'resuming' which gets set to
true early on instead of setting 'suspended' to false,
and allow queueing work but not receiving frames while
resuming.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process the RANN (Root Annoucement) Frame and try to find the HWMP
root station by sending a PREQ.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's currently a very odd bug in mac80211 -- a
hardware scan that is done while the hardware is
really operating on 2.4 GHz will include CCK rates
in the probe request frame, even on 5 GHz (if the
driver uses the mac80211 IEs). Vice versa, if the
hardware is operating on 5 GHz the 2.4 GHz probe
requests will not include CCK rates even though
they should.
Fix this by splitting up cfg80211 scan requests by
band -- recalculating the IEs every time -- and
requesting only per-band scans from the driver.
Apparently this bug hasn't been a problem yet, but
it is imaginable that some older access points get
confused if confronted with such behaviour.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree_skb() should be used to free struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.
Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we do not disconnect when a channel switch is requested,
we end up eventually detection beacon loss from the AP and
then disconnecting, without ever really telling the AP, so
we might just as well disconnect right away.
Additionally, this fixes a problem with iwlwifi where the
driver will clear some internal state on channel changes
like this and then get confused when we actually go clear
that state from mac80211.
It may look like this patch drops the no-IBSS check, but
that is already handled by cfg80211 in the wext handler it
provides for IBSS (cfg80211_ibss_wext_siwfreq).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I accidentally transposed these in the patch that "fixed" the defaults,
leading to extremely low throughput because of the huge min CW.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to cancel all timers in mac80211 when suspending.
In particular we forgot to deal with some things that can
cause hardware reconfiguration -- while it is down.
While at it we go ahead and add a warning in ieee80211_sta_work()
if its run while the suspend->resume cycle is in effect. This
should not happen and if it does it would indicate there is
a bug lurking in either mac80211 or mac80211 drivers.
With this now wpa_supplicant doesn't blink when I go to suspend
and resume where as before there where issues with some timers
running during the suspend->resume cycle. This caused a lot of
incorrect assumptions and would at times bring back the device
in an incoherent, but mostly recoverable, state.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've never really cared about the default QoS (WMM) values, but
we really should if the AP doesn't send any. This patch makes
mac80211 use the default values according to 802.11-2007, and
additionally syncs the default values when we disassociate so
whatever the last AP said gets "unconfigured".
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it and use the proper type. To ease that adjust
struct ieee80211_tim_ie to have a virtual bitmap of size
at least 1.
Also check that the TIM IE is actually present before trying
to parse it!
Because other people may need the function, make it a static
inline in ieee80211.h.
(The original "mac80211: validate TIM IE length" was a minimal fix for
2.6.30. This purports to be the full, correct fix. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regardless of whether the hardware implements beacon filtering,
there's no need to process all beacons in software all the time
throughout the stack (mac80211 does a lot, then cfg80211, then
in the future possibly userspace).
This patch implements the "best possible" beacon filtering in
mac80211. "Best possible" means that it can look for changes in
all requested information elements, and distinguish vendor IEs
by their OUI.
In the future, we will add nl80211 API for userspace to request
information elements and vendor IE OUIs to watch -- drivers can
then implement the best they can do while software implements
it fully.
It is unclear whether or not this actually saves CPU time, but
the data is all in the cache already so it should be fairly
cheap. The additional _testing_, however, has great benefit;
Without this, and on hardware that doesn't implement beacon
filtering, wrong assumptions about, for example, scan result
updates could quickly creep into code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware defects may require the hardware to be re-initialised
completely from scratch. Drivers would need much information (for
instance the current MAC address, crypto keys, beaconing information,
etc.) stored duplicated from mac80211 to be able to do this, so let
mac80211 help them.
The new ieee80211_restart_hw() function requires the same code as
resuming, so move that code into a new ieee80211_reconfig() function
in util.c and leave only the suspend code in pm.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include the HT capabilities in the probe request frame.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pending packets code is quite incomprehensible, uses memory barriers
nobody really understands, etc. This patch reworks it entirely, using
the queue spinlock, proper stop bits and the skb queues themselves to
indicate whether packets are pending or not (rather than a separate
variable like before).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmentation currently uses an allocated array to store the
fragment skbs, and then keeps track of which have been sent
and which are still pending etc. This is rather complicated;
make it simpler by just chaining the fragments into skb->next
and removing from that list when sent. Also simplifies all
code that needs to touch fragments, since it now only needs
to walk the skb->next list.
This is a prerequisite for fixing the stored packet code,
which I need to do for proper aggregation packet storing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using only the RTNL has a number of problems, most notably that
ieee80211_iterate_active_interfaces() and other interface list
traversals cannot be done from the internal workqueue because it
needs to be flushed under the RTNL.
This patch introduces a new mutex that protects the interface list
against modifications. A more detailed explanation is part of the
code change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver is given a wiphy and it wants to get to its private
mac80211 driver area it can use wiphy_to_ieee80211_hw() to get first
to its ieee80211_hw and then access the private structure via hw->priv. The
wiphy_priv() is already being used internally by mac80211 and drivers
should not use this. This can be helpful in a drivers reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is enabled, the AP does not allow a STA to associate if an
existing security association exists without first going through SA
Query process. When this happens, the association request is denied
with a new status code ("temporarily rejected") ans Association
Comeback IE is used to notify when the association may be tried again
(i.e., when the SA Query procedure has timed out).
Use the comeback time to update the mac80211 client MLME timer for
next association attempt to minimize waiting time if association is
temporarily rejected.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse warnings:
net/mac80211/util.c:355:6: warning: symbol
'ieee80211_wake_queue_by_reason' was not declared. Should it be static?
net/mac80211/util.c:385:6: warning: symbol
'ieee80211_stop_queue_by_reason' was not declared. Should it be static?
Thanks to Johannes Berg for reporting this.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.
The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up a number of things:
* the unusable definition of the HT capabilities/HT information
information elements
* variable names that are hard to understand
* mac80211: move ieee80211_handle_ht to ht.c and remove the unused
enable_ht parameter
* mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
* mac80211: fix bug with casting the result of ieee80211_bss_get_ie
to an information element _contents_ rather than the
whole element, add size checking (another out-of-bounds
access bug fixed!)
* mac80211: remove some unused return values in favour of BUG_ON
checking
* a few minor other things
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warn when ieee80211_hw_config returns an error, it shouldn't
happen; remove a number of printks that would happen in such
a case and one printk that is user-triggerable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no checking that the HT IEs are of the right length
which can be used by an attacker to cause an out-of-bounds
access by sending a too short HT information/capability IE.
Fix it by simply pretending those IEs didn't exist when too
short.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the scan functions are called ieee80211_sta_scan_*
or similar, make clean it up so they are all just called
ieee80211_scan_*.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It really doesn't belong into the wireless extensions code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta_tx function isn't MLME code any more,
it's getting used by a lot of code. Move it to utils and
rename it to ieee80211_tx_skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware is started it might be in a confused state with
respect to queue QoS parameters. This patch changes mac80211
to set sane defaults right after the hardware is brought up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IE parsing is required for the mlme and mesh code, it's
not a static function anyway, and it's much better to have it
in util rather than the overly large mlme.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All users have been moved over to the version taking a le16 frame control
rather than a cpu-endian value.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds ieee80211_queue_stopped that let drivers to query
queue status
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make mac80211 transmit correctly fragmented packet after
queue was stopped
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only behavior change is that we do not drop packets under any
circumstances. If that is absolutely needed, we could easily add it
back.
With cleanups and help from Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take a __le16 directly rather than a host-endian value.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses an alignment issue with compare_ether_addr().
The addresses passed to compare_ether_addr should be two bytes aligned.
It may function properly in x86 platform. However may not work properly
on IA-64 or ARM processor.
This also fixes a typo in mlme.c where the sk_buff struct name is incorect.
Though sizeof() works for any incorrect structure pointer name as its just
a pointer length that we want, lets just fix it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having drivers start queues is just confusing, their ->start()
callback can block and do whatever is necessary, so let mac80211
start queues and have drivers wake queues when necessary (to get
packets flowing again right away.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 55c308c1315bc7267dbb88011c208fd743cdce31
("mac80211: QoS related cleanups") introduced another bug,
the queue handling functions that operate on all queues now
only operated on the first queues, not the A-MPDU queues as
expected. This patch fixes this.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit e38bad4766
mac80211: make ieee80211_iterate_active_interfaces not need rtnl
rt2500usb and rt73usb broke down due to attempting register access
in atomic context (which is not possible for USB hardware).
This patch restores ieee80211_iterate_active_interfaces() to use RTNL lock,
and provides the non-RTNL version under a new name:
ieee80211_iterate_active_interfaces_atomic()
So far only rt2x00 uses ieee80211_iterate_active_interfaces(), and those
drivers require the RTNL version of ieee80211_iterate_active_interfaces().
Since they already call that function directly, this patch will automatically
fix the USB rt2x00 drivers.
v2: Rename ieee80211_iterate_active_interfaces_rtnl
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should have been updated at the same time we were transitioning from 3 byte
to 4 byte mesh sequence number. Pointed out by Johannes Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split it into ieee80211_tx_data and ieee80211_rx_data to clarify
usage/flag usage and remove the stupid union thing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Includes integration in struct sta_info of mesh peer link elements, previously
on their own mesh peer link table.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the ability to handle Block Ack Request
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch left only one user of the ieee80211_is_eapol()
function and that user can be eliminated easily by introducing
a new "frame is EAPOL" flag to handle the frame specially (we
already have this information) instead of doing the (expensive)
ieee80211_is_eapol() all the time.
Also, allow unencrypted frames to be sent when they are injected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes should_drop_frame function to pass in ps poll control
frames required for power save functioanlity. Interface types that do not
have interest for PS POLL frames now drop it in handler.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface iteration in mac80211 can be done without holding any
locks because I converted it to RCU. Initially, I thought this
wouldn't be needed for ieee80211_iterate_active_interfaces but
it's turning out that multi-BSS AP support can be much simpler
in a driver if ieee80211_iterate_active_interfaces can be called
without holding locks. This converts it to use RCU, it adds a
requirement that the callback it invokes cannot sleep.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the Rx handlers chain by incorporating previously
handlers ieee80211_rx_h_802_1x_pae and ieee80211_rx_h_drop_unencrypted
into ieee80211_rx_h_data, already in 802.3 form. this scheme follows more
precisely after the IEEE802.11 data plane archituecture, and will prevent
code duplication to IEEE8021.11n A-MSDU handler.
added function:
- ieee80211_data_to_8023: transfering 802.11 data frames to 802.3 frame
- ieee80211_deliver_skb: delivering the 802.3 frames to upper stack
eliminated handlers:
- ieee80211_rx_h_drop_unencrypted: now function ieee80211_drop_unencrypted
- ieee80211_rx_h_802_1x_pae: now function ieee80211_802_1x_pae
changed handlers:
- ieee80211_rx_h_data: now contains calls to four above function
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes drivers need to know which interfaces are associated with
their hardware. Rather than forcing those drivers to keep track of
the interfaces that were added, this adds an iteration function to
mac80211.
As it is intended to be used from the interface add/remove callbacks,
the iteration function may currently only be called under RTNL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a warning about NUM_IEEE80211_MODES missing
in a switch statement. Intentionally do not add a default
case so we get warnings at these places if we need to add
new modes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all mention of the atheros turbo modes that
can't possibly work properly anyway since in some places we don't
check for them when we should.
I have no idea what the iwlwifi drivers were doing with these but
it can't possibly have been correct.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to CTS protection, whether short preambles are used for 802.11b
transmissions should be a per-subif setting, not device global.
For STAs, this patch makes short preamble handling automatic based on the ERP
IE. For APs, hostapd still uses the prism ioctls, but the write ioctl has been
restricted to AP-only subifs.
ieee80211_txrx_data.short_preamble (an unused field) was removed.
Unfortunately, some API changes were required for the following functions:
- ieee80211_generic_frame_duration
- ieee80211_rts_duration
- ieee80211_ctstoself_duration
- ieee80211_rts_get
- ieee80211_ctstoself_get
Affected drivers were updated accordingly.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new file util.c and move a whole bunch of functions into it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
