On my machine, a kexec with this driver loaded in the old kernel causes
a very long delay on boot in the kexec'ed kernel, most likely due to
unclean shutdown prior to that.
Unloading thunderbolt driver prior to kexec allows kexec to work as fast
as regular kernel boot, as well as adding this .shutdown pointer.
Shutting a device prior to the shutdown completely is always a good idea
IMHO to help with kexec, and this one-liner patch implements it.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tiger Lake integrated Thunderbolt/USB4 controller is quite close to
Intel Ice Lake. By default it is still using firmware based connection
manager so we can use most of the Ice Lake flows in Tiger Lake as well.
We check if the firmware connection manager is running and in that case
use it, otherwise use the software based connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.
In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.
While there remove obsolete TODO comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.
While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.
For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.
Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IOMMU is enabled and Thunderbolt driver is built into the kernel
image, it will be probed before IOMMUs are attached to the PCI bus.
Because of this DMA mappings the driver does will not go through IOMMU
and start failing right after IOMMUs are enabled.
For this reason move the Thunderbolt driver initialization happen at
rootfs level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:
- The controller firmware reports to support RTD3
- All the connected devices announce support for RTD3
- There is no active XDomain connection
Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).
The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI defaults to 32-bit DMA mask but this device is capable of full
64-bit addressing, so make sure we first try 64-bit DMA mask before
falling back to the default 32-bit.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware
message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge
somewhat because it is using route strings addressing devices. In
addition to that the DMA port of 4-channel (two port) controller is in
different port number than the previous controllers. There are some
other minor differences as well.
This patch add support for Intel Titan Ridge and the new ICM firmware
message format.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the Thunderbolt domain adding fails for some reason we currently
always return -EIO instead of the real error code. To make debugging
easier return the actual error code instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The driver misses implementation of PM hook that undoes what
->freeze_noirq() does after the hibernation image is created. This means
the control channel is not resumed properly and the Thunderbolt bus
becomes useless in later stages of hibernation (when the image is stored
or if the operation fails).
Fix this by pointing ->thaw_noirq to driver nhi_resume_noirq(). This
makes sure the control channel is resumed properly.
Fixes: 23dd5bb49d ("thunderbolt: Add suspend/hibernate support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
When ring enters polling mode we are expected to mask the ring interrupt
before the callback is called. However, the current code actually
unmasks it probably because of a copy-paste mistake.
Mask the interrupt properly from now on.
Fixes: 4ffe722eef ("thunderbolt: Add polling mode for rings")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0day kbuild robot reports following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: tb_property_find+0xe/0x41
*pde = 00000000
Oops: 0000 [#1]
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.0-rc1-00741-ge69b6c0 #412
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
task: 89c80000 task.stack: 89c7c000
EIP: tb_property_find+0xe/0x41
EFLAGS: 00210246 CPU: 0
EAX: 00000000 EBX: 7a368f47 ECX: 00000044 EDX: 7a368f47
ESI: 8851d340 EDI: 7a368f47 EBP: 89c7df0c ESP: 89c7defc
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 027a2000 CR4: 00000690
Call Trace:
tb_register_property_dir+0x49/0xb9
? cdc_mbim_driver_init+0x1b/0x1b
tbnet_init+0x77/0x9f
? cdc_mbim_driver_init+0x1b/0x1b
do_one_initcall+0x7e/0x145
? parse_args+0x10c/0x1b3
? kernel_init_freeable+0xbe/0x159
kernel_init_freeable+0xd1/0x159
? rest_init+0x110/0x110
kernel_init+0xd/0xd0
ret_from_fork+0x19/0x30
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.
These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).
The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.
The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.
The security levels are as follows:
none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.
The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.
In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.
In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.
Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On PCs the NHI host controller is only present when there is a device
connected. When the last device is disconnected the host controller will
dissappear shortly (within 10s). Now if that happens when we are
suspended we should not try to touch the hardware anymore, so add a flag
for this and check it before we re-enable rings.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host controller includes two sets of registers that are used to
communicate with the firmware. Add functions that can be used to access
these registers.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Intel Win Ridge (Thunderbolt 2) and Alpine Ridge (Thunderbolt 3)
controller PCI IDs to the list of supported devices.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt fabric consists of one or more switches. This fabric is
called domain and it is controlled by an entity called connection
manager. The connection manager can be either internal (driven by a
firmware running on the host controller) or external (software driver).
This driver currently implements support for the latter.
In order to manage switches and their properties more easily we model
this domain structure as a Linux bus. Each host controller adds a domain
device to this bus, and these devices are named as domainN where N
stands for index or id of the current domain.
We then abstract connection manager specific operations into a new
structure tb_cm_ops and convert the existing tb.c to fill those
accordingly. This makes it easier to add support for the internal
connection manager in subsequent patches.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Thunderbolt controllers support up to 16 MSI-X vectors. Using
MSI-X is preferred over MSI or legacy interrupt and may bring additional
performance because there is no need to check the status registers which
interrupt was triggered.
While there we convert comments in structs tb_ring and tb_nhi to follow
kernel-doc format more closely.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Xavier Gnata <xavier.gnata@gmail.com>
Add support to INTEL_FALCON_RIDGE_2C controller and corresponding quirk
to support suspend/resume.
Tested against 4.7 master on a MacBook Air 11" 2015.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
The pci device ids listed in the thunderbolt driver are to restrictive,
which prevents the driver from being loaded on recent Apple MacBooks
using a thunderbolt 2 controller. In particular this prevented any
hot-plugging functionality for thunderbolt based ethernet dongles
(i.e. Apples thunderbolt gigabit ethernet broadcom tg3 based dongle
Model A1433 EMC 2590).
Changing the subvendor and subdevice to PCI_ANY_ID the thunderbolt driver
loads and binds to the pci device 07:00.0 System peripheral:
Intel Corporation Device 156c which is the thunderbolt 2 controller on
the MacBookPro12,1.
Successfully tested on MacBookPro12,1. With the patch the thunderbolt
module gets now loaded on boot. And it provides hot-plugging support both
for a cold-plugged and a warm-plugged ethernet dongle.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Acked-by: Knuth Posern <knuth@posern.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advantage of kcalloc is, that will prevent integer overflows
which could result from the multiplication of number of elements
and size and it is also a bit nicer to read.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nhi->rx_rings does not have type as struct tb_ring *, as it is a
double pointer so the elements of the array should have pointer type,
not structure type.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Cc: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'nhi_ids' is local to this file.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'descriptors' is a pointer. Use NULL isntead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use _noirq since we have to restore the pci tunnels before the pci
core wakes the tunneled devices.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct tb which will contain our view of the thunderbolt bus. For
now it just contains a pointer to the control channel and a workqueue
for hotplug events.
Add thunderbolt_alloc_and_start() and thunderbolt_shutdown_and_free()
which are responsible for setup and teardown of struct tb.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple
decided to implement thunderbolt at the operating system level. The
firmare only initializes thunderbolt devices that are present at boot
time. This driver enables hotplug of thunderbolt of non-chained
thunderbolt devices on Apple systems with a cactus ridge controller.
This first patch adds the Kconfig file as well the parts of the driver
which talk directly to the hardware (that is pci device setup, interrupt
handling and RX/TX ring management).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
