PCI code was outside of CONFIG_PCI, add __initdata at cyrix_55x0 (since
accessed within __init function only).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The i386 page fault handler does not allow enough slack when checking for
userspace access below the current stack pointer. This prevents use of the
enter instruction by user code. Fix this by allowing enough slack for
"enter $65535,$31" to execute.
Problem reported by Tomasz Malesinski <tmal@mimuw.edu.pl>
Tested using this program, based on the original from Tomasz:
.file "ovflow.S"
.version "01.01"
gcc2_compiled.:
.section .rodata
.LC0:
.string "asdf\n"
.text
.align 4
.globl main
.type main,@function
main:
nest_level=0
.rept 30
enter $0,$nest_level
nest_level=nest_level+1
.endr
enter $65535,$30
enter $65535,$31
addl $-12,%esp
pushl $.LC0
call printf
addl $16,%esp
.L2:
.rept 32
leave
.endr
ret
.Lfe1:
.size main,.Lfe1-main
.ident "GCC: (GNU) 2.95.4 20011002 (Debian prerelease)"
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On i386, kernel irq balance doesn't work.
1) In function do_irq_balance, after kernel finds the min_loaded cpu but
before calling set_pending_irq to really pin the selected_irq to the
target cpu, kernel does a cpus_and with irq_affinity[selected_irq].
Later on, when the irq is acked, kernel would calls
move_native_irq=>desc->handler->set_affinity to change the irq affinity.
However, every function pointed by
hw_interrupt_type->set_affinity(unsigned int irq, cpumask_t cpumask)
always changes irq_affinity[irq] to cpumask. Next time when recalling
do_irq_balance, it has to do cpu_ands again with
irq_affinity[selected_irq], but irq_affinity[selected_irq] already
becomes one cpu selected by the first irq balance.
2) Function balance_irq in file arch/i386/kernel/io_apic.c has the same
issue.
[akpm@osdl.org: cleanups]
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If CONFIG_FRAME_POINTERS is enabled, and one does a dump_stack() during
early SMP init, an infinite stackdump and a bootup hang happens:
[<c0104e7f>] show_trace+0xd/0xf
[<c0104e96>] dump_stack+0x15/0x17
[<c01440df>] save_trace+0xc3/0xce
[<c014527d>] mark_lock+0x8c/0x4fe
[<c0145df5>] __lockdep_acquire+0x44e/0xaa5
[<c0146798>] lockdep_acquire+0x68/0x84
[<c1048699>] _spin_lock+0x21/0x2f
[<c010d918>] prepare_set+0xd/0x5d
[<c010daa8>] generic_set_all+0x1d/0x201
[<c010ca9a>] mtrr_ap_init+0x23/0x3b
[<c010ada8>] identify_cpu+0x2a7/0x2af
[<c01192a7>] smp_store_cpu_info+0x2f/0xb4
[<c01197d0>] start_secondary+0xb5/0x3ec
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[<c104ec11>] end_of_stack_stop_unwind_function+0x1/0x4
[...]
Due to "end_of_stack_stop_unwind_function" recursing back to itself in the
EBP stackframe-walker. So avoid this type of recursion when walking the
stack .
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple updates matching a given CPU are found in the update file, the
action taken by the microcode update driver was inappropriate:
- when lower revision microcode was found before matching or higher revision
one, the driver would needlessly complain that it would not downgrade the
CPU
- when microcode matching the currently installed revision was found before
newer revision code, no update would actually take place
To change this behavior, the driver now concludes about possibly updates and
issues messages only when the entire input was parsed.
Additionally, this adds back (in different places, and conditionalized upon
a new module option) some messages removed by a previous patch.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Tigran Aivazian <tigran_aivazian@symantec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only drm, framebuffer, mtrr parts + misc files here and there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- avoid expensive modulo (integer division) which happened
since APM_MAX_EVENTS is 20 (non-power-of-2)
- kill compiler warnings by initializing two variables
- add __read_mostly to some important static variables that are read often
(by idle loop etc.)
- constify several structures
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the x86 cache-bypassing copy instructions for copy_from_user().
Some performance data are
Total of GLOBAL_POWER_EVENTS (CPU cycle samples)
2.6.12.4.orig 1921587
2.6.12.4.nt 1599424
1599424/1921587=83.23% (16.77% reduction)
BSQ_CACHE_REFERENCE (L3 cache miss)
2.6.12.4.orig 57427
2.6.12.4.nt 20858
20858/57427=36.32% (63.7% reduction)
L3 cache miss reduction of __copy_from_user_ll
samples %
37408 65.1412 vmlinux __copy_from_user_ll
23 0.1103 vmlinux __copy_user_zeroing_intel_nocache
23/37408=0.061% (99.94% reduction)
Top 5 of 2.6.12.4.nt
Counted GLOBAL_POWER_EVENTS events (time during which processor is not stopped) with a unit mask of 0x01 (mandatory) count 100000
samples % app name symbol name
128392 8.0274 vmlinux __copy_user_zeroing_intel_nocache
64206 4.0143 vmlinux journal_add_journal_head
59746 3.7355 vmlinux do_get_write_access
47674 2.9807 vmlinux journal_put_journal_head
46021 2.8774 vmlinux journal_dirty_metadata
pattern9-0-cpu4-0-09011728/summary.out
Counted BSQ_CACHE_REFERENCE events (cache references seen by the bus unit) with a unit mask of 0x3f (multiple flags) count 3000
samples % app name symbol name
69755 4.2861 vmlinux __copy_user_zeroing_intel_nocache
55685 3.4215 vmlinux journal_add_journal_head
52371 3.2179 vmlinux __find_get_block
45504 2.7960 vmlinux journal_put_journal_head
36005 2.2123 vmlinux journal_stop
pattern9-0-cpu4-0-09011744/summary.out
Counted BSQ_CACHE_REFERENCE events (cache references seen by the bus unit) with a unit mask of 0x200 (read 3rd level cache miss) count 3000
samples % app name symbol name
1147 5.4994 vmlinux journal_add_journal_head
881 4.2240 vmlinux journal_dirty_data
872 4.1809 vmlinux blk_rq_map_sg
734 3.5192 vmlinux journal_commit_transaction
617 2.9582 vmlinux radix_tree_delete
pattern9-0-cpu4-0-09011731/summary.out
iozone results are
original 2.6.12.4 CPU time = 207.768 sec
cache aware CPU time = 184.783 sec
(three times run)
184.783/207.768=88.94% (11.06% reduction)
original:
pattern9-0-cpu4-0-08191720/iozone.out: CPU Utilization: Wall time 45.997 CPU time 64.527 CPU utilization 140.28 %
pattern9-0-cpu4-0-08191741/iozone.out: CPU Utilization: Wall time 46.878 CPU time 71.933 CPU utilization 153.45 %
pattern9-0-cpu4-0-08191743/iozone.out: CPU Utilization: Wall time 45.152 CPU time 71.308 CPU utilization 157.93 %
cache awre:
pattern9-0-cpu4-0-09011728/iozone.out: CPU Utilization: Wall time 44.842 CPU time 62.465 CPU utilization 139.30 %
pattern9-0-cpu4-0-09011731/iozone.out: CPU Utilization: Wall time 44.718 CPU time 59.273 CPU utilization 132.55 %
pattern9-0-cpu4-0-09011744/iozone.out: CPU Utilization: Wall time 44.367 CPU time 63.045 CPU utilization 142.10 %
Signed-off-by: Hiro Yoshioka <hyoshiok@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_move_pages() support for 32bit (i386 plus x86_64 compat layer)
Add support for move_pages() on i386 and also add the compat functions
necessary to run 32 bit binaries on x86_64.
Add compat_sys_move_pages to the x86_64 32bit binary layer. Note that it is
not up to date so I added the missing pieces. Not sure if this is done the
right way.
[akpm@osdl.org: compile fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate the various arch-specific implementations of pxm_to_node() and
node_to_pxm() into a single generic version.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix ondemand vs suspend deadlock
[CPUFREQ] Fix powernow-k8 SMP kernel on UP hardware bug.
[PATCH] redirect speedstep-centrino maintainer mail to cpufreq list
[CPUFREQ] correct powernow-k8 fid/vid masks for extended parts
[CPUFREQ] Clarify powernow-k8 cpu_family statements
I haven't really maintained this driver for a while, and I'm not
keeping up with the latest in Intel power management. I get a steady
stream of mail which I don't really do anything useful with; the
cpufreq list seems like a better destination, unless someone wants to
get the mail directly.
Also clean up a couple of ancient comments which don't really apply
anymore (as far as I know, nobody has ever damaged a CPU with this
driver).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On 15 Jun 2006 03:45:10 +0200, Andi Kleen wrote:
> Anyways I would say that if the BIOS can't get MCFG right then
> it's likely not been validated on that board and shouldn't be used.
According to Petr Vandrovec:
... "What is important (and checked) is address of MMCONFIG reported by MCFG
table... Unfortunately code does not bother with printing that address :-(
"Another problem is that code has hardcoded that MMCONFIG area is 256MB large.
Unfortunately for the code PCI specification allows any power of two between 2MB
and 256MB if vendor knows that such amount of busses (from 2 to 128) will be
sufficient for system. With notebook it is quite possible that not full 8 bits
are implemented for MMCONFIG bus number."
So here is a patch. Unfortunately my system still fails the test because
it doesn't reserve any part of the MMCONFIG area, but this may fix others.
Booted on x86_64, only compiled on i386. x86_64 still remaps the max area
(256MB) even though only 2MB is checked... but 2.6.16 had no check at all
so it is still better.
PCI: reduce size of x86 MMCONFIG reserved area check
1. Print the address of the MMCONFIG area when the test for that area
being reserved fails.
2. Only check if the first 2MB is reserved, as that is the minimum.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This a bit late (yours patch was posted about a year ago), but
a co-worker of spotted part of the code that looks like a memory
leak. Looking at the code it seems that pci_mmcfg_config should
be free-ed if MMCONFIG is above 4GB.
From: Konrad Rzeszutek <konradr@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a PCI device is disabled via pci_disable_device(), it's still
left decoding its BAR resource ranges even though its driver
will have likely released those regions (and may even have
unloaded). pci_enable_device() already explicitly enables
BAR resource decode for the device being enabled. This patch
disables resource decode for the PCI device being disabled,
making it symmetric with the enable call.
I saw this while doing something else, not because of a
problem report. Still, seems to be the correct thing to do.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The fid/vid masks for parts using the extended parts are slightly incorrect and can result in
incorrect fid/vid codes being applied. No instances of this problem have been reported in
the field but it could be a problem with future parts.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch clarifies the meaning of the cpu_family if
statements in the hw pstate driver patch for powernow-k8
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
From: "Andy Currid" <ACurrid@nvidia.com>
This patch fixes a kernel panic during boot that occurs on NVIDIA platforms
that have HPET enabled.
When HPET is enabled, the standard timer IRQ is routed to IOAPIC pin 2 and is
advertised as such in the ACPI APIC table - but an earlier workaround in the
kernel was ignoring this override. The fix is to honor timer IRQ overrides
from ACPI when HPET is detected on an NVIDIA platform.
Signed-off-by: Andy Currid <acurrid@nvidia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sets minimum PLL divider to 2.
No negative impact when tested with two nForce2 based boards.
Alexander Choporov reported (06/01/06) that xdiv = 1 does not work on his
Abit NF7S2. Although there shouldn't be much cases that lead to xdiv = 1.
(Updates also the (C) year)
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Even though powernow-k7 doesn't work in SMP environments,
it can work on an SMP configured kernel if there's only
one CPU present, however recalibrate_cpu_khz was returning
-EINVAL on such kernels, so we failed to init the cpufreq driver.
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some Centrino cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some NForce2 cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Forthcoming AMD products will use a different algorithm for transitioning
pstates than the current generation Opteron products do. The attached
patch allows the powernow-k8 driver to work with those products.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This prevents annoying messages being printed when it gets
loaded on a machine that doesn't have support scaling via ACPI.
Signed-off-by: Dave Jones <davej@redhat.com>
This reverts commit 5491d0f3e2.
As per Andi:
"After some discussion with people who have the affected system it
seems best to revert for 2.6.17. It broke a common BIOS workaround
and PCI-X still doesn't work. Alternative is for people to change
the BIOS which seems to be better right now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
When using apic= on the kernel command line, this had no effect for machines
matched by either the ACPI MADT or the MPS OEM table scan. However, when such
option is specified, it should also take effect for this set of systems.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This shouldn't have actually caused any problems
(as we return if we 'corrupt' 'i', but it's still not
very pretty. For the sake of adding another local variable,
this got cleaner.
Signed-off-by: Dave Jones <davej@redhat.com>
Writing cr0 to cr2 register can't be right. This fixes the typo. I wonder
how it could survive so long.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Kdump second kernel boot fails after a system crash if second kernel
is UP and acpi=off and if crash occurred on a non-boot cpu.
o Issue here is that MP tables report boot cpu lapic id as 0 but second
kernel is booting on a different processor and MP table data is stale
in this context. Hence apic_id_registered() check fails in setup_local_APIC()
when called from APIC_init_uniprocessor().
o Problem is not seen if ACPI is enabled as in that case
boot_cpu_physical_apicid is read from the LAPIC.
o Problem is not seen with SMP kernels as well because in this case also
boot_cpu_physical_apicid is read from LAPIC. (smp_boot_cpus()).
o The problem is fixed by reading boot_cpu_physical_apicid from LAPIC
if it is a UP kernel and CRASH_DUMP is enabled.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 stack dump has a "<0>" in the middle of the line and an extra space
between columns in multicolumn mode. Remove those and also remove an extra
blank line of source code.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed to see all devices.
The system has multiple PCI segments and we don't handle that properly
yet in PCI and ACPI. Short term before this is fixed blacklist it to
pci=noacpi.
Acked-by: len.brown@intel.com
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HOTPLUG_CPU entry says "Say Y..." then "Say N.". Slightly ugly, so I fixed
it up, and added remark about suspend on SMP as a bonus.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to oprofile for the Intel Core Solo and Core Duo processors.
See also the patch to add support to oprofile-0.9.1-8.1.1 at
http://www.kvack.org/~bcrl/patches/oprofile/oprofile-core-0.9.1.diff .
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 10dbe196a8.
The resource struct is still 32-bit, so trying to save a 64-bit memory
size there obviously won't work.
When we merge the 64-bit resource series, we can re-enable this.
Thanks to Sachin Sant and Maneesh Soni for debugging
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Sachin Sant <sachinp@in.ibm.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sharyathi Nagesh <sharyath@in.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Cc: len.brown@intel.com
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
