This is based on user feedback from Doug Ledford at RedHat:
Events that occur on an rdma_cm_id are reported to userspace through an
event channel. Connection request events are reported on the event
channel associated with the listen. When the connection is accepted, a
new rdma_cm_id is created and automatically uses the listen event
channel. This is suboptimal where the user only wants listen events on
that channel.
Additionally, it may be desirable to have events related to connection
establishment use a different event channel than those related to
already established connections.
Allow the user to migrate an rdma_cm_id between event channels. All
pending events associated with the rdma_cm_id are moved to the new event
channel.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable conn_id remove on the passive side after connection
establishment. This corrects an issue where the IB driver can't be
unloaded after running applications over RDS. The 'dev_remove' counter
does not reach 0 for established connections on the passive side.
This problem is limited to device removal, and only occurs on the
passive side if there are established connections.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In cancel_mads(), MADs are moved from the wait_list and local_list
to a cancel_list for processing. However, the structures on these two
lists are not the same. The wait_list references struct
ib_mad_send_wr_private, but local_list references struct
ib_mad_local_private. Cancel_mads() treats all items moved to the
cancel_list as struct ib_mad_send_wr_private. This leads to a system
crash when requests are moved from the local_list to the cancel_list.
Fix this by leaving local_list alone. All requests on the local_list
have completed are just awaiting processing by a queued worker thread.
Bug (crash) reported by Dotan Barak <dotanb@dev.mellanox.co.il>.
Problem with local_list access reported by Robert Reynolds
<rreynolds@opengridcomputing.com>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add performance/debug counters to track sent/received messages, retries,
and duplicates. Counters are tracked per CM message type, per port.
The counters are always enabled, so intrusive state tracking is not done.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To allow ULPs to tune timeout values and capture retry statistics,
report the number of times that a mad send operation was retried.
For RMPP mads, report the total number of times that the any portion
(send window) of the send operation was retried.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
P_key changes can invalidate multicast groups. Report errors on all
multicast groups affected by a pkey change.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
log_max_eqs is a 4-bit field, not a 3-bit field in the response to the
QUERY_DEV_CAP FW command, so we should mask with 0xf instead of 0x7
when reading it.
Found by Yossi Leybovitch of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the work completion error code to the QP error debug output.
This makes it easier to determine the cause of the error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An internal code review found the comment here lacking -- update it with
more specifics of how and why the rmb() is there.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a code review, someone noticed the comments didn't match the code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The gen2_basic tests check for the errno value when a CQ is resized
smaller than the number of outstanding completions queue on the CQ.
This patch changes ib_ipath to return EINVAL which is what ib_mthca
returns and what gen2_basic expects.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code review pointed out that the locking around uses of ipath_sendctrl
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one point in time there was code to allow a user process to
wait for a send buffer if none were available. This feature was
never used and most of the code was removed. This removes
some missed unused code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 5.0 firmware now supports translating sgls in recv work requests,
so remove the host driver logic currently doing the translation.
Note: this change requires 5.0 firmware.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the call into cxgb3 to get the driver info is not serialized.
The iw_cxgb3 module needs to hold the rtnl_lock around the ethtool ops
call like dev_ioctl() does.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Tested-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The local loopback of an outgoing DR SMP response is limited to those
that originate at the driver specific SMA implementation during the
driver specific process_mad() function. This patch enables a
returning DR SMP originating in userspace (or elsewhere) to be
delivered to the local managment stack. In this specific case the
driver process_mad() function does not consume or process the MAD, so
a reponse mad has not be created and the original MAD must manually be
copied to the MAD buffer that is to be handed off to the local agent.
Signed-off-by: Steve Welch <swelch@systemfabricworks.com>
Acked-by: Hal Rosenstock <hal@xsigo.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is in response to reviewing a patch to the core MAD
processing which fixes loopback of directed route packets to/from user
level MAD agents. This change enables the core code to work for
ib_ipath by fixing the return code from the ipath process_mad method.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ib_mad_recv_done_handler(), the response pointer is checked for
NULL after allocating it. It is then checked again in the local
process_mad() path but there is no possibility of it changing in
between.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Hal Rosenstock <hal@xsigo.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the initiator depth and responder resources to the device max
values for new connect request events in the iWARP connection manager.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve interrupt handler cache footprint by noinline'ing error
functions that are rarely called.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some IB adapters (notably IBM's eHCA) do not implement SRQs (shared
receive queues). The current IPoIB connected mode support only works
on devices that support SRQs.
Fix this by adding support for using the receive queue of each
connected mode receive QP. The disadvantage of this compared to using
an SRQ is that it means a full queue of receives must be posted for
each remote connected mode peer, which means that total memory usage
is potentially much higher than when using SRQs. To manage this, add
a new module parameter "max_nonsrq_conn_qp" that limits the number of
connections allowed per interface.
The rest of the changes are fairly straightforward: we use a table of
struct ipoib_cm_rx to hold all the active connections, and put the
table index of the connection in the high bits of receive WR IDs.
This is needed because we cannot rely on the struct ib_wc.qp field for
non-SRQ receive completions. Most of the rest of the changes just
test whether or not an SRQ is available, and post receives or find
received packets in the right place depending on the answer.
Cleaning up dead connections actually becomes simpler, because we do
not have to do the "last WQE reached" dance that is required to
destroy QPs attached to an SRQ. We just move the QP to the error
state and wait for all pending receives to be flushed.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
[ Completely rewritten and split up, based on Pradeep's work. Several
bugs fixed and no doubt several bugs introduced. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code for going through the rx_reap list of struct
ipoib_cm_rx and freeing each one. This consolidates the code
duplicated between ipoib_cm_dev_stop() and ipoib_cm_rx_reap() and
reduces the risk of error when adding additional accounting.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to create an SRQ and allocate the receive ring in
ipoib_cm_dev_init() into a new function ipoib_cm_create_srq(). This
will make the code neater when support for devices that don't implement
SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to unmap/free skbs and free the receive ring in
ipoib_cm_dev_cleanup() into a new function ipoib_cm_free_rx_ring().
This function will be called from a couple of other places when
support for devices that don't implement SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 23b9c1ab ("Infiniband: make ipath driver use default driver
groups.") introduced a bug in the ipath driver where
ipath_device_create_group() fell through into the error path, even on
success, which meant that the sysfs groups it created would always get
removed right away. This made ipath_device_remove_group() hit the
BUG_ON() in sysfs_remove_group() when it tried to remove those groups a
second time.
Correct the return path so that the groups stick around until they are
supposed to be cleaned up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (509 commits)
V4L/DVB (7078): radio: fix sf16fmi section mismatch
V4L/DVB (7077): bt878: remove handcrafted PCI subsystem ID check
V4L/DVB (7075): Make a local function static
V4L/DVB (7074): DiB7000P: correct tuning problem for 7MHz channel
V4L/DVB (7073): DiB7070: Reception quality improved
V4L/DVB (7072): sets the MT2060 IF1 frequency according to EEPROM
V4L/DVB (7071): DiB0700: Start streaming the right way
V4L/DVB (7070): Fix some tuning problems
V4L/DVB (7069): Support for myTV.t
V4L/DVB (7068): Add support for WinTV Nova-T-CE driver
V4L/DVB (7067): fix autoserach in the Hauppauge NOVA-T 500
V4L/DVB (7066): ASUS My Cinema U3000 Mini DVBT Tuner
V4L/DVB (7065): Artec T14BR patches
V4L/DVB (7063): xc5000: Fix OOPS caused by missing firmware
V4L/DVB (7062): radio-si570x: Some fixes and new USB ID addition
V4L/DVB (7061): radio-si470x: Some cleanups
V4L/DVB (7060): em28xx: remove has_tuner
V4L/DVB (7059): cx88: Ensure the tuner is reset correctly
V4L/DVB (7058): IR corrections for the Pinnacle 800i
V4L/DVB (7056): tuner: suppress obsolete tuner i2c address warning for XC5000 tuners
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (67 commits)
ide: remove redundant DMA blacklist check from __ide_dma_on()
ide: cleanup ide_set_dma()
ide: remove redundant ->ide_dma_on call from set_using_dma()
sc1200: move DMA timings to timing tables
ide: add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag
sis5513: factor out UDMA programming code
pdc202xx_new: move PIO programming code to pdcnew_set_pio_mode()
ide: make 'extra' field in struct ide_port_info u8
ide: kill duplicate code in ide_dump_{ata,atapi}_status()
ide-disk: use ide_get_lba_addr()
ide: printk fix
ide: add ide_tf_read() helper
ide: fix registers loading order in ide_dump_ata_status()
ide-disk: use do_rw_taskfile() (take 2)
ide-disk: add ide_tf_set_cmd() helper
ide-disk: extend timeout for PIO-in commands
ide: remove 'handler' field from ide_task_t (take 2)
ide: use ->data_phase to set ->handler in do_rw_taskfile()
ide: convert do_rw_taskfile() to use ->data_phase
ide: merge flagged_taskfile() into do_rw_taskfile()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: (96 commits)
sched: keep total / count stats in addition to the max for
sched, futex: detach sched.h and futex.h
sched: fix: don't take a mutex from interrupt context
sched: print backtrace of running tasks too
printk: use ktime_get()
softlockup: fix signedness
sched: latencytop support
sched: fix goto retry in pick_next_task_rt()
timers: don't #error on higher HZ values
sched: monitor clock underflows in /proc/sched_debug
sched: fix rq->clock warps on frequency changes
sched: fix, always create kernel threads with normal priority
debug: clean up kernel/profile.c
sched: remove the !PREEMPT_BKL code
sched: make PREEMPT_BKL the default
debug: track and print last unloaded module in the oops trace
debug: show being-loaded/being-unloaded indicator for modules
sched: rt-watchdog: fix .rlim_max = RLIM_INFINITY
sched: rt-group: reduce rescheduling
hrtimer: unlock hrtimer_wakeup
...
->ide_dma_on method is called only after successful ide_dma_check() call
(ide_dma_check()->ide_tune_dma() checks DMA blacklist) or if drive->using_dma
has been previously enabled for a given device (->ide_dma_on is the only place
which sets drive->using_dma to '1').
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->dma_off_quietly is always called before ide_set_dma()
so the call can be moved inside ide_set_dma().
* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
call for 'rc == -1' case is redundant, remove it.
* '0' and '-1' are the only values returned by ide_dma_check()
so remove dead code for other cases.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_set_dma() calls ->ide_dma_on method itself and returns zero
only if ->ide_dma_on call succeeded.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on pata_sc1200.c.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out UDMA programming code from sis_set_dma_mode() to per
chipset family helpers: sis_{ata33,ata133}_program_udma_timings().
* Add sis_program_udma_timings() helper.
* Remove unneeded casts to 'unsigned long'.
* Minor cleanups.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move PIO programming code from pdcnew_set_mode() to pdcnew_set_pio_mode().
* Rename pdcnew_set_mode() to pdcnew_set_dma_mode().
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The maximum value used currently for 'extra' field in struct ide_port_info
is 240.
Make 'extra' u8 so it packs nicely together with enablebits[] and 'chipset'
fields (ide_pci_enablebit_t is 3 bytes and hwif_chipset_t is 1 byte).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move the common code from ide_dump_{ata,atapi}_status() to
ide_dump_status().
* ide_dump_{ata,atapi}_status() -> ide_dump_{ata,atapi}_error().
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Export ide_get_lba_addr().
* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().
* Remove incorrect comment from idedisk_read_native_max_address()
(noticed by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
power4:
drivers/ide/ide-lib.c: In function `ide_dump_sector':
drivers/ide/ide-lib.c:516: warning: long long unsigned int format, u64 arg (arg 2)
We don't know what type is used to implement u64 hence it must always be cast
when printed.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code reading taskfile registers from ide_end_drive_cmd()
to the new ide_tf_read() helper.
* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
particular IDE taskfile register in ide_tf_read().
* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.
* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.
* Factor out code getting sector address from ide_dump_ata_status()
to the new ide_dump_sector() function.
* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().
* Remove no longer needed ide_read_24().
The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix registers loading order in ide_dump_ata_status()/ide_read_24().
Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
to skip loading taskfile registers in do_rw_taskfile().
* Export do_rw_taskfile().
* Convert __ide_do_rw_disk() to use do_rw_taskfile().
* Unexport ide_tf_load().
* Unexport {pre_task_out,task_in}_intr() and make it static.
* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.
There should be no functionality changes caused by this patch.
v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_tf_set_cmd() helper for selecting/setting command and data phase
(note: DMA data phases are there for completness, they are not required ATM).
* Set IDE_TFLAG_WRITE taskfile flag for write requests in __ide_do_rw_disk().
* Convert __ide_do_rw_disk() to use the new ide_tf_set_cmd() helper.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
s/WAIT_CMD/WAIT_WORSTCASE/ to make the timeout the same as in do_rw_taskfile()
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
which require custom handlers. Check the flag in do_rw_taskfile() and set
handler accordingly.
* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
ide_tf_set_{specify,restore,setmult}_cmd().
* Make {set_geometry,recal,set_multmode}_intr() static.
* Remove no longer needed 'handler' field from ide_task_t.
v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
