These macros have been defined for several years since v2.6.12-rc2（tracing by git）,
but never be used. So remove them.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ICMP_MIB_MAX is equal to the total number of icmp mib,
So no need to add 1. This wastes 4/8 bytes memory.
Change it to be same as ICMP6_MIB_MAX, TCP_MIB_MAX, UDP_MIB_MAX.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing AF-specific about remembering the timestamp
for a time-wait TCP socket is getting the peer.
Abstract that behind a new timewait_sock_ops vector.
Support for real IPV6 sockets is not filled in yet, but
curiously this makes timewait recycling start to work
for v4-mapped ipv6 sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Then we can make a completely generic tcp_remember_stamp()
that uses ->get_peer() as a helper, minimizing the AF specific
code and minimizing the eventual code duplication when we implement
the ipv6 side of TW recycling.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. SCTP_CMD_NUM_VERBS,SCTP_CMD_MAX
These two macros have never been used for several years since v2.6.12-rc2.
2.sctp_port_rover,sctp_port_alloc_lock
The commit 063930 abandoned global variables of port_rover and port_alloc_lock,
but still keep two macros to refer to them.
So, remove them now.
commit 0639300900
Author: Stephen Hemminger <shemminger@linux-foundation.org>
Date: Wed Oct 10 17:30:18 2007 -0700
[SCTP]: port randomization
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fl->fl_gre_key is network byte order contrary to fl->fl_icmp_*.
Make xfrm_flowi_{s|d}port return network byte order values for gre
key too.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros have been existed for several years since v2.6.12-rc2.
But they never be used. So remove them now.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)
scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_sk_mc_lock rwlock becomes a spinlock.
readers (inet6_mc_check()) now takes rcu_read_lock() instead of read
lock. Writers dont need to disable BH anymore.
struct ipv6_mc_socklist objects are reclaimed after one RCU grace
period.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit is same in nature as v2.6.37-rc1-755-g3654654; the network
namespace itself is not modified when calling net_generic, so the
parameter can be const.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
jiffies is defined as "volatile".
extern unsigned long volatile __jiffy_data jiffies;
ACCESS_ONCE() uses "volatile".
As a result, some compilers warn duplicate `volatile' for ACCESS_ONCE(jiffies).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each net_device contains address family specific data such as
per device settings and statistics. We already expose this data
via procfs/sysfs and partially netlink.
The netlink method requires the requester to send one RTM_GETLINK
request for each address family it wishes to receive data of
and then merge this data itself.
This patch implements a new API which combines all address family
specific link data in a new netlink attribute IFLA_AF_SPEC.
IFLA_AF_SPEC contains a sequence of nested attributes, one for each
address family which in turn defines the structure of its own
attribute. Example:
[IFLA_AF_SPEC] = {
[AF_INET] = {
[IFLA_INET_CONF] = ...,
},
[AF_INET6] = {
[IFLA_INET6_FLAGS] = ...,
[IFLA_INET6_CONF] = ...,
}
}
The API also allows for address families to implement a function
which parses the IFLA_AF_SPEC attribute sent by userspace to
implement address family specific link options.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now, fields in struct sock are not optimally ordered, because each
path (RX softirq, TX completion, RX user, TX user) has to touch fields
that are contained in many different cache lines.
The really critical thing is to shrink number of cache lines that are
used at RX softirq time : CPU handling softirqs for a device can receive
many frames per second for many sockets. If load is too big, we can drop
frames at NIC level. RPS or multiqueue cards can help, but better reduce
latency if possible.
This patch starts with UDP protocol, then additional patches will try to
reduce latencies of other ones as well.
At RX softirq time, fields of interest for UDP protocol are :
(not counting ones in inet struct for the lookup)
Read/Written:
sk_refcnt (atomic increment/decrement)
sk_rmem_alloc & sk_backlog.len (to check if there is room in queues)
sk_receive_queue
sk_backlog (if socket locked by user program)
sk_rxhash
sk_forward_alloc
sk_drops
Read only:
sk_rcvbuf (sk_rcvqueues_full())
sk_filter
sk_wq
sk_policy[0]
sk_flags
Additional notes :
- sk_backlog has one hole on 64bit arches. We can fill it to save 8
bytes.
- sk_backlog is used only if RX sofirq handler finds the socket while
locked by user.
- sk_rxhash is written only once per flow.
- sk_drops is written only if queues are full
Final layout :
[1] One section grouping all read/write fields, but placing rxhash and
sk_backlog at the end of this section.
[2] One section grouping all read fields in RX handler
(sk_filter, sk_rcv_buf, sk_wq)
[3] Section used by other paths
I'll post a patch on its own to put sk_refcnt at the end of struct
sock_common so that it shares same cache line than section [1]
New offsets on 64bit arch :
sizeof(struct sock)=0x268
offsetof(struct sock, sk_refcnt) =0x10
offsetof(struct sock, sk_lock) =0x48
offsetof(struct sock, sk_receive_queue)=0x68
offsetof(struct sock, sk_backlog)=0x80
offsetof(struct sock, sk_rmem_alloc)=0x80
offsetof(struct sock, sk_forward_alloc)=0x98
offsetof(struct sock, sk_rxhash)=0x9c
offsetof(struct sock, sk_rcvbuf)=0xa4
offsetof(struct sock, sk_drops) =0xa0
offsetof(struct sock, sk_filter)=0xa8
offsetof(struct sock, sk_wq)=0xb0
offsetof(struct sock, sk_policy)=0xd0
offsetof(struct sock, sk_flags) =0xe0
Instead of :
sizeof(struct sock)=0x270
offsetof(struct sock, sk_refcnt) =0x10
offsetof(struct sock, sk_lock) =0x50
offsetof(struct sock, sk_receive_queue)=0xc0
offsetof(struct sock, sk_backlog)=0x70
offsetof(struct sock, sk_rmem_alloc)=0xac
offsetof(struct sock, sk_forward_alloc)=0x10c
offsetof(struct sock, sk_rxhash)=0x128
offsetof(struct sock, sk_rcvbuf)=0x4c
offsetof(struct sock, sk_drops) =0x16c
offsetof(struct sock, sk_filter)=0x198
offsetof(struct sock, sk_wq)=0x88
offsetof(struct sock, sk_policy)=0x98
offsetof(struct sock, sk_flags) =0x130
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sockets refcount is usually 2, unless an incoming frame is going to
be queued in receive or backlog queue.
Using atomic_inc_not_zero_hint() permits to reduce latency, because
processor issues less memory transactions.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changed functions do not modify the NL messages and/or attributes
at all. They should use const (similar to strchr), so that callers
which have a const nlmsg/nlattr around can make use of them without
casting.
While at it, constify a data array.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change
to BIT(8).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43legacy is compiled on the arm platform, the following errors are seen:
CC [M] drivers/net/wireless/b43legacy/xmit.o
In file included from include/net/dst.h:11,
from drivers/net/wireless/b43legacy/xmit.c:31:
include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__'
before '____cacheline_aligned_in_smp'
include/net/dst_ops.h: In function 'dst_entries_get_fast':
include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_get_slow':
include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_add':
include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_init':
include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_destroy':
include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named
'pcpuc_entries'
make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1
make[3]: *** [drivers/net/wireless/b43legacy] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
The cause is a missing include of <linux/cache.h>, which is present for
i386 and x86_64 architectures, but not for arm.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE Key field is intended to be used for identifying an individual
traffic flow within a tunnel. It is useful to be able to have XFRM
policy selector matches to have different policies for different
GRE tunnels.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
