When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Lucas Correia Villa Real
This patch defines S3C2400 memory map and adds a S3C24XX macro for
common resources between S3C2400, S3C2410 and S3C2440 cpus.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some folk want to use RGB555 rather tahn RGB565 with amba-clcd.
Allow amba-clcd to accept either pixel format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resetting the adapter causes the ServeRAID driver to exceed
the max time allowed by the softlock watchdog. Resetting the
hardware can easily require 30 or more seconds. To avoid the
"BUG: soft lockup detected on CPU#0!"
result, this patch replaces the mdelay() calls in the
initialization/reset routines with msleep().
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE
case. I put "fixes" in quotes because the real fix would be to completely
remove it, but that's beyond the scope of this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New versions of the Power5 firmware can send a "re-enable" message to
the virtual scsi adapter. This fix makes us handle the message
correctly. Without it, the driver goes catatonic and the system crashes
unpleasantly.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the documentation error for 'SERIAL_8250' in
drivers/serial/Kconfig
Signed-off-by: Timothy Charles McGrath <tmHikaru@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Same reasoning as commit 747c8a5594
but this time we're making uart_port flags a bitwise type - not
all of these flags correspond with the old ASYNC_ flags, so there
is the possibility for bugs if the wrong ASYNC_* constants are
used. Always use UPF_* constants for uart_port->flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The functionality UPF_BOOT_ONLYMCA provided has been replaced by
the 8250_mca module, which only registers MCA ports if MCA is
present.
UPF_AUTOPROBE has no functional effect - in fact, it's never
tested. Only ibmasm set the flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch resolves most of the problems with an SMP serial console race
with output via the tty path. At the end of the serial console print we
force enable the tx int in case we clobbered the tx interrupt status
racing between the console and tty output. That way the extra tx
interrupt causes the transmit path to restart not hang.
It also makes the serial console printk use the FIFO. This is neccessary
because some remote management devices fake serial console with FIFO and
are confused into sending one packet per character over ethernet when we
stall rather than filling the FIFO.
In order to preserve existing reliability semantics the function waits
for the serial queue to completely empty before returning.
Both of these problems were identified by a Red Hat partner.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to have request_irq followed by set_irq_type.
Just use request_irq with the appropriate SA_TRIGGER flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
some driver clean ups, and a re-posting of changes that are needed
to match the updated TPS.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix incorrect variable size used to hold register value. This bug might
wipe out a portion of the TCR value when setting the interface options.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eddie C. Dost <ecd@brainaid.de>
I have the following patch for serial console over the RSC
(remote system controller) on my E250 machine. It basically adds
support for input-device=rsc and output-device=rsc from OBP, and
allows 115200,8,n,1,- serial mode setting.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Andrew Victor
This patch fixes two small issues with 2.6.15-git12.
1) Corrected major/minor numbers for ttyAT devices in the KConfig help.
(Patch from Karl Olsen)
2) tty->flip.count has been removed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove page refcount manipulations from cassini driver by using
another field in struct page. Needed for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added e1000_mc_addr_list_update
Added e1000_read_reg_io
Added e1000_enable_pciex_master
These are not static functions, that is why we have them declared in the header.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These functions help restore the driver to active configuration when coming out of resume for power management.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Align the prefetches to a dword to help speed them up.
Recycle skb's and early replenish.
Force memory writes to complete before fetching more descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is a new device which is look like:
Serial controller: Decision Computer International Co. PCCOM2 (rev 02) (prog-if 02 [16550])
0700: 6666:0004 (rev 02) (prog-if 02)
Flags: medium devsel, IRQ 177
Memory at fe000000 (32-bit, non-prefetchable) [size=128]
I/O ports at e880 [size=128]
I/O ports at e400 [size=256]
It has two 16550A, and is not listed in kernel, although the
manufacturer clams that it is supported...
I've created the following patch, it only add the new PCI id and the
card to the repository, it seems to work.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7493a314cb changed the ordering
of the registration of the platform device driver vs the 8250 drivers
internal initialisation. This led to the probe function being called
before the driver had finished its internal initialisation, causing
mayhem. Revert the ordering change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Somewhat cleaner in the resync as someone cleaned up the pio xfer users
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sizeof() return is not an int, so use max_t to get the types right.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about transmit locking, this solves a possible race
between tx_complete and transmit, that would cause a tx timeout.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to inline quite so many routines, let the compiler
decide
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: Stephen Hemminger <shemminger@osdl.or>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to zero out the status ring entries after processing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about memory barriers. The only place we really
need them is before and after updating the chip's ring interface.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to call pci_set_consistent_dma_mask in the case of 64 bit
DMA.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to make sure that sky2 receive buffers are 64 bit
aligned. Also, don't need to start off with GFP_ATOMIC
on initial setup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: e100 whitespace fixes
These are whitespace only fixes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Handle the return values from pci_* functions
This is to resolve warnings during compile time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue)
Set the end of list bit to cause the hardware's transmit state machine to
work correctly and not prevent management (BMC) traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sbusfb_compat_ioctl() needs to return int, not long, as that
is what the fb_ops->fb_compat_ioctl method prototype wants.
Need to git rid of the "struct file *file" first argument to
fbiogetputcmap() and fbiogscursor() to match calls done in
sbusfb_compat_ioctl().
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cassini.c:1930: warning: long unsigned int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk level and remove unnecessary CONFIG_SMP|CONFIG_PREEMPT tests
as this is taken care through the spinlock macros anyway.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I misread the spec when doing the original. I've tested the corrected
version with pre UDMA drives and it now picks the right modes. This is a
specific bug fix rather than an update or new feature item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds the Intel ICH8 DID's to the ahci.c file for AHCI mode
SATA support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Improves small packet performance with large amounts of reassembly being done in the stack.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This was to fix compilation warnings. Also added log messages when pci_enable_* functions return with an error.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is two patches, the first is adding additional bus information for the 8257{1|2|3} controllers. The second patch was orginally a community patch to print bus type/speed/width, and enhanced by us.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The EEPROM image version is reported as a firmware version for these controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added 82571 fiber to WOL fix for dual port adapters.
Added support for 82546GB (Quad Copper).
Added PCIe typedef for x2, igp cable length 115, and extended TX CTRL registers.
Added parity error detection and PCIe CTRL registers.
Added EEPROM config registers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed an issue netpoll would error out during communication, generating the following error:
--netdump[14973]: Got toomany timeouts in handshaking, ...
Even after a kernel panic, netpoll requires two way communication to successfully transfer the crash log to the remote server.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Simplified the logic used to assign the frame_size.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed VLAN support by switching control over to the firmware.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed by moving code to correct location (for 82572 and 82571 controllers).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the collision distance for 82543 controllers and newer.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Removed duplicate code, TXDCTL and TXDCTL_COUNT_DESC are the same bit and there is no need to set it twice.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These were two separate community submitted patches.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the TX timeout logic to use "end of packet" rather than "next to clean". Updated message log.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains two fixes. The first fix is to the tx and rx descriptor rings clean up process. The second fix is to jumbo frames, which cleans up the code logic and removes most of the fifo related limitations on jumbo frames. This is because the driver code now supports splitting a packet across multiple descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
10/100 speeds seem to have some problems reporting false tx timeouts especially at half duplex. Fixed by using a timeout factor to attempt to mitigate the false timeouts.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed flow control water marks based on PBA size.
Store flow control state in original_fc in addition to fc.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed read_eeprom logic to test use_eerd instead of testing for 82573 controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the loopback logic to work for the PCI express adapters.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
