* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: correct segfault in generation of 32-bit reloc kernel
All EP93xx based systems can support Ethernet. This patch moves
the platform_device setup from the various board support files
into the core support file. The Ethernet driver data still remains
in the individual platform setup files to allow specific platform
configuration.
This also adds Ethernet support to the edb9302, edb9312, and
edb9315 platforms.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: segfault on build of a 32-bit relocatable kernel
When converting arch/x86/boot/compressed/relocs.c to support unlimited
sections, the computation of sym_strtab in walk_relocs() was done
incorrectly. This causes a segfault for some people when building the
relocatable 32-bit kernel.
Pointed out by Anonymous <pageexec@freemail.hu>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes a regression that came with 934b2857cc
("[S390] nohz/sclp: disable timer on synchronous waits.").
If udelay() gets called from a disabled context it sets the clock comparator
to a value where it expects the next interrupt. When the interrupt happens
the clock comparator gets not reset and therefore the interrupt condition
doesn't get cleared. The result is an endless timer interrupt loop.
In addition this patch fixes also the following:
rcutorture reveals that our __udelay implementation is still buggy,
since it might schedule tasklets, but prevents their execution:
NOHZ: local_softirq_pending 42
NOHZ: local_softirq_pending 02
NOHZ: local_softirq_pending 142
NOHZ: local_softirq_pending 02
To fix this we make sure that only the clock comparator interrupt
is enabled when the enabled wait psw is loaded.
Also no code gets called anymore which might schedule tasklets.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop. The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Though from a hardware perspective it would be sensible to use only a
32-bit unsigned int type Linux defines interrupt flags to be stored in
an unsigned long and nothing else.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These instructions were placed in the code directly as opcodes because
early compilers didn't support them. Toolchains supporting ARMv7
understand these instructions and the patch puts the mnemonics back.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently on the EP93xx platform early kernel messages go to UART1.
Since this UART is the only one that has modem control signals it
might be used for another purpose and it is undesirable for those
messages to appear. This patch allows one of the other UARTs to be
selected in the kernel configuration. It is assumed that the
bootloader has configured and initialized the UART since this was the
previous assumption.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EXPORT sharpsl_param which is necessary to support modular build of some depending drivers.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[patch] x86: Trivial printk fix in efi.c
The following line is lacking a space between "memdesc" and "doesn't".
"Kernel-defined memdescdoesn't match the one from EFI!"
Fixed the printk by adding a space.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds basic support for the Mobilepro
900/c mini-laptop. At present it won't do much
more than build and boot.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds generic battery driver for wm97xx chips.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point converting memory bank addresses from physical to
virtual just to convert them back to physical addresses. Furthermore
this isn't "right" for highmem even if in this case the end result is
the correct one.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 00c5372d37 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- use MFP-API for GPIO
- support TRIZEPS4WL module
- cleanups
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes formatting issues in mach-sa1100/
machine files. More specificly badge4.c,generic.c and
pleb.c.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the jornada default
config (which was made for 2.6.12). Plenty
of development has happend since then, most
importantly the SSP driver and kbd/touchscr.
This config has been tested to compile
and bootup properly.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable Sparsemem support for LH7A40x SoCs, while still allowing the
existing discontig support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... including some comments about the ordering required to bring
sparsemem up. You have to repeatedly guess, test, reguess, try
again and again to work out what the right ordering is. Many
hours later...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for detecting non-executable stack binaries, and adjust
permissions to prevent execution from data and stack areas. Also,
ensure that READ_IMPLIES_EXEC is enabled for older CPUs where that
is true, and for any executable-stack binary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The newly introduced sanity_check_meminfo() function should be
used to collect all validation of the meminfo array, which we
have in bootmem_init(). Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make sure that coprocessor instructions for range ops are contiguous
and not reordered.
- s/invalidate_and_disable_dcache/flush_and_disable_dcache/
- Don't re-enable I/D caches if they were not enabled initially.
- Change some masks to shifts for better generated code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
The PTRS_PER_PMD != 1 condition can be evaluated with C code and
optimized at compile time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix failure to shutdown with CPU hotplug
powerpc: Fix PCI in Holly device tree
The current -march=armv7a is not supported by mainline gcc.
Cc: Paul Brook <paul@codesourcery.com>
Cc: Wei Zhong <weizhong@broadcom.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the dma_unmap_* calls, we don't touch the cache when a DMA
buffer transitions from device to CPU ownership. Presently, no
problems have been identified with speculative cache prefetching
which in itself is a new feature in later architectures. We may
have to revisit the DMA API later for these architectures anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The number of BIOSes that have an option to enable the IOMMU, or fix
anything about its configuration, is vanishingly small. There's no good
reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Export set_memory_ro() and set_memory_rw() calls for use by drivers that need
to have more debug information about who might be writing to memory space.
this was initially developed for use while debugging a memory corruption
problem with e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I tracked down the shutdown regression to CPUs not dying
when being shut down during power-off. This turns out to
be due to the system_state being SYSTEM_POWER_OFF, which
this code doesn't take as a valid state for shutting off
CPUs in.
This has never made sense to me, but when I added hotplug
code to implement hibernate I only "made it work" and did
not question the need to check the system_state. Thomas
Gleixner helped me dig, but the only thing we found is
that it was added with the original commit that added CPU
hotplug support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Delay exit to make sure we can actually get the optimal result in as
many cases as possible.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Initial fix for making sure that we can access percpu variables
in all C code (commit: 10617bbe84)
inadvertantly allocated the memory in the "percpu" section of
the vmlinux ELF executable. This confused kexec/dump.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,tty: Fix tty polling search to use name correctly
kgdb, x86_64: fix PS CS SS registers in gdb serial
kgdb, x86_64: gdb serial has BX and DX reversed
kgdb, x86, arm, mips, powerpc: ignore user space single stepping
kgdb: could not write to the last of valid memory with kgdb
The name of the platform device 'at91_pwm_leds' conflicts with the
function at91_pwm_leds().
So rename the device 'at91_pwm_leds_device' to be more specific.
Similarly rename 'at91_gpio_leds_device' for consistency.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the LEDs on the Conitec ARM&EVA board.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Validate the direction argument like x86 does. In addition,
validate the dma_unmap_* parameters against those passed to
dma_map_* when using the DMA bounce code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dmabounce dma_sync_xxx() implementation have been broken for
quite some time; they all copy data between the DMA buffer and
the CPU visible buffer no irrespective of the change of ownership.
(IOW, a DMA_FROM_DEVICE mapping copies data from the DMA buffer
to the CPU buffer during a call to dma_sync_single_for_device().)
Fix it by getting rid of sync_single(), moving the contents into
the recently created dmabounce_sync_for_xxx() functions and adjusting
appropriately.
This also makes it possible to properly support the DMA range sync
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
v2: should check with half of range0 size instead of chunk_size
So don't have silly big hole.
in hpa's case we could auto detect instead of adding mtrr_chunk_size in
command line.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add mtrr_cleanup_debug to print out more info about layout
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
change back chunksize max to 2g
otherwise will get strange layout in 2G ram system like
0 - 4g WB, 2040M - 2048M UC, 2048M - 4G NC
instead of
0 - 2g WB, 2040M - 2048M UC
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch defines pcibios_map_irq() and pcibios_plat_dev_init() for
the BCM47xx platform.
It fixes the regression introduced by commit
aab547ce0d.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_map_irq is no way of returning an error but on IP27 an interrupt
is possibly not routable when running out of resources. So do the
interrupt routing at pcibios_enable_device time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Brownell <david-b@pacbell.net> wrote:
> The problem is that "value" is zero-or-nonzero.
> This code wrongly assumes it's zero-or-one.
> Possible fix: "((!!value) << gpio)".
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As far as I know no M32R hardware actually has ISA slots.
And ISA drivers don't compile on M32R.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Remove the unused NOHIGHMEM option.
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TOUCH_PANEL_IRQ is never referenced, and set_irq_type() shouldn't
be called in this way, remove it, as well as the idp_init_irq(),
and use pxa25x_init_irq() instead.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Cliff Brake <cliff.brake@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.
Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains very basic support of Palm Zire 72.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Delete ARM's own cnt32_to_63.h as the copy in include/linux/ should now be
used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 the gdb serial register structure defines the PS (also known
as eflags), CS and SS registers as 4 bytes entities.
This patch splits the x86_64 regnames enum into a 32 and 64 version to
account for the 32 bit entities in the gdb serial packets.
Also the program counter is properly filled in for the sleeping
threads.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On the x86 arch, user space single step exceptions should be ignored
if they occur in the kernel space, such as ptrace stepping through a
system call.
First check if it is kgdb that is executing a single step, then ensure
it is not an accidental traversal into the user space, while in kgdb,
any other time the TIF_SINGLESTEP is set, kgdb should ignore the
exception.
On x86, arm, mips and powerpc, the kgdb_contthread usage was
inconsistent with the way single stepping is implemented in the kgdb
core. The arch specific stub should always set the
kgdb_cpu_doing_single_step correctly if it is single stepping. This
allows kgdb to correctly process an instruction steps if ptrace
happens to be requesting an instruction step over a system call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This patch adds specific power-off method for Buffalo Linkstation Mini
board. The board has a hardware switch which should be monitored from
userspace. When the switch is in OFF position the board should be rebooted
and U-Boot will start in an idle mode and wait for the user to move the
power switch back to ON position.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
We can translate a struct page directly to a DMA address using
page_to_dma(). No need to use page_address() followed by
virt_to_dma().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Buffalo Linkstation Mini board.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Feroceon L2 cache can work in eighther write through or write back mode
on Kirkwood. Add the option to configure this mode according to Kconfig.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch provides standard GPIO LED control
for the ED Mini V2, with software blinking only
(CPLD hardware blinking capability is not used).
This patch also provides status of the power
button as a standard GPIO input event.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Remove uart1 init calls for boards that use the physical pins onto
which the UART1 signals are multiplexed for different purposes.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Add support to the Kirkwood port for newer device models and silicon
revisions. Instead of looking at the DEVICE_ID register, the device
version is now determined by looking at the PCI-Express device ID and
revision registers, as it is done for orion5x, and this information
is used to determine the TCLK frequency, again, as it is done for
orion5x.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, kirkwood uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family.
This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
The RD88F6183AP-GE is an access point reference design for the
88F6183 SoC, with a 88E6161 six-port gigabit ethernet switch with
five PHYs (providing 1 WAN and 4 LAN ports and an interface to the
CPU), and a mini-PCIe slot for a wireless card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the Buffalo Terastation Pro II/Live.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the LaCie Ethernet Disk mini V2.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, orion5x uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family (and can vary based on strap pin settings).
This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This replaces the original cache type decoding printks. We now
indicate how we're treating the cache which we found, rather
than what we found.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than trying to (inaccurately) decode the cache type from the
registers each time we need to decide what type of cache we have,
use a bitmask initialized early during boot.
Since the setup is a one-off initialization, we can be a little more
clever and take account of the CPU architecture as well.
Note that we continue to achieve the compactness on optimised kernels
by forcing tests to always-false or always-true as appropriate, thereby
allowing the compiler to do build-time code elimination.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cache type register found in ARMv5 and later CPUs changes format
and meaning depending on the CPU architecture version. Currently,
this code:
a) doesn't work for everything - Xscale's are identified as
'unknown 5'.
b) is not able to tell whether the caches are VIVT or VIPT from the
cache type.
c) prints rubbish on some ARMv6 and ARMv7+ CPUs.
The two solutions to this are:
1. Add yet more code to decode and print the various different register
formats.
2. Remove the code altogther.
The code only exists to decode and print the cache parameters.
Increasing the complexity of it just for the sake of a few prinks
isn't worth it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point to have such initialization in struct dma_mapping_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, GART alloc_coherent tries to allocate pages with GFP_DMA32
for a device having dma_masks > 24bit < 32bits. If GART gets an
address that a device can't access to, GART try to map the address to
a virtual I/O address that the device can access to.
But Andi pointed out, "The GART is somewhere in the 4GB range so you
cannot use it to map anything < 4GB. Also GART is pretty small."
http://lkml.org/lkml/2008/9/12/43
That is, it's possible that GART doesn't have virtual I/O address
space that a device can access to. The above behavior doesn't work for
a device having dma_masks > 24bit < 32bits.
This patch restores old GART alloc_coherent behavior (before the
alloc_coherent rewrite).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts:
commit bee44f294e
Author: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Date: Fri Sep 12 19:42:35 2008 +0900
x86: make GART to respect device's dma_mask about virtual mappings
I wrote the above commit to fix a GART alloc_coherent regression, that
can't handle a device having dma_masks > 24bit < 32bits, introduced by
the alloc_coherent rewrite:
http://lkml.org/lkml/2008/8/12/200
After the alloc_coherent rewrite, GART alloc_coherent tried to
allocate pages with GFP_DMA32. If GART got an address that a device
can't access to, GART mapped the address to a virtual I/O address. But
GART mapping mechanism didn't take account of dma mask, so GART could
use a virtual I/O address that the device can't access to again.
Alan pointed out:
" This is indeed a specific problem found with things like older
AACRAID where control blocks must be below 31bits and the GART
is above 0x80000000. "
The above commit modified GART mapping mechanism to take care of dma
mask. But Andi pointed out, "The GART is somewhere in the 4GB range so
you cannot use it to map anything < 4GB. Also GART is pretty small."
http://lkml.org/lkml/2008/9/12/43
That means it's possible that GART doesn't have virtual I/O address
space that a device can access to. The above commit (to modify GART
mapping mechanism to take care of dma mask) can't fix the regression
reliably so let's avoid making GART more complicated.
We need a solution that always works for dma_masks > 24bit <
32bits. That's how GART worked before the alloc_coherent rewrite.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PXA26x (PXA261/262) is actually a PXA250 with stacked Intel(R)
StartaFlash. And this can be decided by bit 3 (PKG_TYPE) of
BOOT_DEF register.
Due to this extra I/O register access, make cpu_is_pxa26x() a
public function instead of a macro.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. add a CPUID table in the comment
2. make cpu_is_pxa25x() true for PXA210/250/255/26x
3. PXA210 is treated as PXA25x, all related code modified to
reflect this
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: prevent stale state of c1e_mask across CPU offline/online, fix
Make sched_clock() report time since boot rather than time since last
timer interrupt.
Make sched_clock() expand and scale the 32-bit TSC value running at
IOCLK speed (~33MHz) to a 64-bit nanosecond counter, using cnt32_to_63()
acquired from the ARM arch and without using slow DIVU instructions
every call.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move asm-arm/cnt32_to_63.h to include/linux/ so that MN10300 can make
use of it too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boardrev is always treated as a u32 everywhere else, no reason to
byteswap the 0xc2 value. The only use is to print out if it is
a prerelease board, the test being:
(olpc_platform_info.boardrev & 0xf) < 8
Which is currently always true as be32_to_cpu(0xc2) & 0xf = 0
but I doubt that was the intention here. The consequences of the bug
are pretty minor though (incorrect boardrev displayed in dmesg when
ofw support not configured)
Also annotate the temporary used to read the boardrev in the ofw
case.
The confusion was noticed by Sparse:
arch/x86/kernel/olpc.c:206:32: warning: cast to restricted __be32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/ptrace.c:763:29: warning: Using plain integer as NULL pointer
arch/x86/kernel/ptrace.c:777:46: warning: Using plain integer as NULL pointer
arch/x86/kernel/ptrace.c:1115:45: warning: Using plain integer as NULL pointer
arch/x86/kernel/ds.c:482:26: warning: Using plain integer as NULL pointer
arch/x86/kernel/ds.c:487:25: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The OLPC doesn't support APM but also doesn't have DMI, so we can't detect
and disable it based on DMI data. So, just disable based on machine_is_olpc()
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix build error introduced by commit 4faac97d44 ("x86: prevent stale
state of c1e_mask across CPU offline/online").
process_32.c needs to include idle.h to get the prototype for
c1e_remove_cpu()
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When setting the direction of one GPIO pin we have to keep the state of the
other pins, hence use binary OR. Also gpio_direction_output() wants to set an
initial value, so add that too.
This fixes a problem with the USB power switch on mtx-1 boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix build error in !oneshot case
x86: c1e_idle: don't mark TSC unstable if CPU has invariant TSC
x86: prevent C-states hang on AMD C1E enabled machines
clockevents: prevent mode mismatch on cpu online
clockevents: check broadcast device not tick device
clockevents: prevent stale tick_next_period for onlining CPUs
x86: prevent stale state of c1e_mask across CPU offline/online
clockevents: prevent cpu online to interfere with nohz
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix 27-rc crash on vsmp due to paravirt during module load
x86, oprofile: BUG scheduling while atomic
AMD IOMMU: protect completion wait loop with iommu lock
AMD IOMMU: set iommu sunc flag after command queuing
Use generic pca953x which provides gpiolib interface instead of
akita-specific akita-ioexp with non-standard interface to pins.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz
Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi
Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now poodle/corgi/spitz have been been converted to use SPI-based
drivers, remove the now unused corgi_ssp.c and corgi_lcd.c. And
as well as the unused reference of {corgi,spitz}ssp_device.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
TODO: figure out the MFP configuration of the SSP2 which looks like
to be already configured by the boot loader, though.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Separated into this dedicated generic GPIO conversion patch for the
work of deprecating pxa_gpio_mode().
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MFP configuration table is reverse engineered from those
magic GAFRx_{L|U} values, and it looks much better now.
Also, the deprecated pxa_gpio_mode() invocations are removed.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct manipulation of GPIO registers are no longer encouraged, use
the new GPIO API instead. Since the GPIO has to be requested before
use, .startup and .shutdown are added to the IrDA device platform
data to request and free the GPIO.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kexec fails on systems with blocks of uncached memory
[IA64] Ski simulator doesn't need check_sal_cache_flush
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix missing devices due to PCI bridge test in of_create_pci_dev().
sparc64: Fix disappearing PCI devices on e3500.
Impact: Functional TSC is marked unstable on AMD family 0x10 and 0x11 CPUs.
This would be wrong because for those CPUs "invariant TSC" means:
"The TSC counts at the same rate in all P-states, all C states, S0,
or S1"
(See "Processor BIOS and Kernel Developer's Guides" for those CPUs.)
[ tglx: Changed C1E to AMD C1E in the printks to avoid confusion
with Intel C1E ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: System hang when AMD C1E machines switch into C2/C3
AMD C1E enabled systems do not work with normal ACPI C-states
even if the BIOS is advertising them. Limit the C-states to
C1 for the ACPI processor idle code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hang which happens across CPU offline/online on AMD C1E systems.
When a CPU goes offline then the corresponding bit in the broadcast
mask is cleared. For AMD C1E enabled CPUs we do not reenable the
broadcast when the CPU comes online again as we do not clear the
corresponding bit in the c1e_mask, which keeps track which CPUs
have been switched to broadcast already. So on those !$@#& machines
we never switch back to broadcasting after a CPU offline/online cycle.
Clear the bit when the CPU plays dead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
27-rc fails to boot up if configured to use modules.
Turns out vsmp_patch was marked __init, and vsmp_patch being the
pvops 'patch' routine for vsmp, a call to vsmp_patch just turns out
to execute a code page with series of 0xcc (POISON_FREE_INITMEM -- int3).
vsmp_patch has been marked with __init ever since pvops, however,
apply_paravirt can be called during module load causing calls to
freed memory location.
Since apply_paravirt can only be called during init/module load, make
vsmp_patch with "__init_or_module"
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just like in the arch/sparc64/kernel/of_device.c code fix commit
071d7f4c3b411beae08d27656e958070c43b78b4 ("sparc64: Fix SMP bootup
with CONFIG_STACK_DEBUG or ftrace.") we have to check the OF device
node name for "pci" instead of relying upon the 'device_type' property
being there on all PCI bridges.
Tested by Meelis Roos, and confirmed to make the PCI QFE devices
reappear on the E3500 system.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a memory segment in memory map with attribute of EFI_MEMORY_UC
is denoted as "System RAM" in /proc/iomem, while memory of attribute
(EFI_MEMORY_WB|EFI_MEMORY_UC) is also labeled the same.
The kexec utility then includes uncached memory as part of vmcore. The
kdump kernel MCA'ed when it tries to save the vmcore to a disk. A normal
"cached" access may cause MCAs.
This patch would label memory with attribute of EFI_MEMORY_UC only as
"Uncached RAM" so that kexec would know not to include it in the vmcore.
I will submit a separate kexec-tools patch to the kexec list.
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Peter Chubb reported that commit 3463a93def
(Update check_sal_cache_flush to use platform_send_ipi()) broke
Ski because it does not implement IPIs.
Tony Luck suggested we just #ifndef out the call (since the simulator
does not have the SAL bug that this code is attempting to detect and
workaround)
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch against tip/x86/iommu virtually reverts
2842e5bf31. But just reverting the
commit breaks AMD IOMMU so this patch also includes some fixes.
The above commit adds new two options to x86 IOMMU generic kernel boot
options, fullflush and nofullflush. But such change that affects all
the IOMMUs needs more discussion (all IOMMU parties need the chance to
discuss it):
http://lkml.org/lkml/2008/9/19/106
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's a small window when NMI watchdog is being set up that if any NMIs
are triggered, the NMI code will make make use of not initalized wd_ops
elements:
void setup_apic_nmi_watchdog(void *unused)
{
if (__get_cpu_var(wd_enabled))
return;
/* cheap hack to support suspend/resume */
/* if cpu0 is not active neither should the other cpus */
if (smp_processor_id() != 0 && atomic_read(&nmi_active) <= 0)
return;
switch (nmi_watchdog) {
case NMI_LOCAL_APIC:
/* enable it before to avoid race with handler */
--> __get_cpu_var(wd_enabled) = 1;
--> if (lapic_watchdog_init(nmi_hz) < 0) {
(...)
asmlinkage notrace __kprobes void default_do_nmi(struct pt_regs *regs)
{
(...)
if (nmi_watchdog_tick(regs, reason))
return;
(...)
notrace __kprobes int
nmi_watchdog_tick(struct pt_regs *regs, unsigned reason)
{
(...)
if (!__get_cpu_var(wd_enabled))
return rc;
switch (nmi_watchdog) {
case NMI_LOCAL_APIC:
rc |= lapic_wd_event(nmi_hz);
(...)
int lapic_wd_event(unsigned nmi_hz)
{
struct nmi_watchdog_ctlblk *wd = &__get_cpu_var(nmi_watchdog_ctlblk);
u64 ctr;
--> rdmsrl(wd->perfctr_msr, ctr);
and wd->*_msr will be initialized on each processor type specific setup, after
enabling NMIs for PMIs. Since the counter was just set, the chances of an
performance counter generated NMI is minimal, but any other unknown NMI would
trigger the problem. This patch fixes the problem by setting everything up
before enabling performance counter generated NMIs and will set wd_enabled
using a callback function.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
P4s have a quirk that makes necessary to clear P4_CCCR_OVF bit on the CCCR
everytime the PMI is triggered. When booting the kernel with reset_devices
(more specific kdump case), the counters reach zero and the PMI will be
generated. This is not a problem on other processors but on P4s, it'll
continue to generate NMIs until that bit is cleared. Since there may be
other users of the performance counters, clear and disable all of them
when booting with reset_devices option.
We have a P4 box here that crashes because of this problem. Since the kdump
kernel usually boots with only one processor active, the second logical
unit won't be set up, therefore, MSR_P4_IQ_CCCR1 (and other performance
counter registers) won't be cleared and P4_CCCR_OVF may be still set because
the previous kernel was using this register. An NMI is triggered because of
the MSR_P4_IQ_CCCR1 right after the NMI delivery is enabled, triggering the
race fixed on my previous email.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86 has set_bit_string() that does the exact same thing that
set_bit_area() in lib/iommu-helper.c does.
This patch exports set_bit_area() in lib/iommu-helper.c as
iommu_area_reserve(), converts GART, Calgary, and AMD IOMMU to use it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could help catch attention about bug in bios about mtrr mask setting.
WARN_ONCE got into mainline already, lets use it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a check for ioremap() failure in copy_oldmem_page().
This patch also includes small coding style fixes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
