This patch adds CanoScan N1240U/LiDE30 (Scanner) to the list of quirky USB
devices.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add kernel-doc entries in <linux/usb.h> for:
Warning(linux-2.6.22-git12//include/linux/usb.h:162): No description found for parameter 'intf_assoc'
Warning(linux-2.6.22-git12//include/linux/usb.h:268): No description found for parameter 'intf_assoc[USB_MAXIADS]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
our list of devices which cannot be suspended keeps growing.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackberry Pearl can run in two modes; a usb-storage only mode
and a mode that allows access via mass storage and to its database.
The berry_charge module will set the device to dual mode and thus we
should ignore its native mode if that module is built
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial patch to build the IOWARRIOR when it is selected in Kconfig.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some system hardware, we are seeing moderately common cases of the
chip errormask register being overwritten due to a chip bug in iba6120
that is triggered by a vendor-specific PCIe broadcast message. This
patch merely checks periodically, and corrects it if needed (the
overwrite can cause us to not get error and hardware error
interrupts). Also, make dd->ipath_errormask the one, true canonical
source for kr_errormask, and remove references to ipath_ignorederrs as
it is currently unused.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There was confused use of INFINIPATH_S_PIOBUFAVAILUPD (value) and
IPATH_S_PIOBUFAVAILUPD (bit position). Also, some callers of
ipath_cancel_sends() need kr_sendctrl restored, and some want to do it
later.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one time the ipath_minrev field was initialized prior to the
ipath_init_iba6120_funcs call, but that is no longer the case, so the
slower put_tid routine was always being used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fastrcvint code's purpose was to avoid reading the interrupt
status if kernel packets were in the receive queue (to reduce
overhead). Because intstatus was not read, we could miss the error
interrupt bit indicating freeze mode, since it only delivers a single
interrupt, even if still pending after intclear is written.
This patch removes that unsafe optimization.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a potential null dereference bug where we dereference
DEV before a null check. This patch simply moves the dereferencing after
the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
protect smc_start_xmit, smc_interrupt and media_check by spin_lock.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Fix to increment the received packet count correctly.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed the call to pci_set_power_state to reset the adapter as it was resulting
in system crash on some platforms.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Mask single and double bit ETQ ecc errors to inhibit spurious interrupts.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Checking for the return value of pci map function
- Implemented Francois Romieu's comments on eliminating code duplication
using goto
- Implemented Francois Romieu's comments on using a temporary variable for
accessing statistics structure
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed 3 buffer mode support from driver - unused feature
- Incorporated Jeff Garzik's comments on elimination of inline typecasting
- Code cleanup : Removed a few extra spaces
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some leftover code that makes use of adapter->lock in tx_timeout function,
which resets the interface under this lock. In close() when the workqueue
is flushed, prints the warning about sleeping with interrupts disabled
(when spinlock debug is enabled). The lock was required with private netxen
IOCTLs, which were removed a while ago.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes masking of interrupts on multiport adapters. Also disables
interrupts upon ifdown interface. The wrong mask could result in interrupt
flood after interface is down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for firmware bug with 2nd port of multiport adapter,
where MAC address is reset. Driver just needs to overwrite it with the
value read from PROM.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove Val Henson as tulip maintainer and let her roam free, FREE!
Signed-off-by: Val Henson <val@nmt.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In older chipsets, the mac address was stored in reversed order.
However, in newer chipsets, the mac address is in correct order. This
patch takes those newer chipsets into account and does not rely on a
special bit setup by BIOS'.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the following modpost warning:
WARNING: vmlinux.o(.init.text+0x1aa6c): Section mismatch: reference to .exit.text:gfar_mdio_exit (between 'gfar_init' and 'gfar_mdio_init')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Additional explanation of problems with locking by Alan Cox.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a potential null dereference bug where we dereference
pegasus before a null check. This patch simply moves the dereferencing
after the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The fcv1236d support patch was created before the "dvb: remove static
dependencies on dvb-pll" patch was applied, but the fcv1236d patch didn't
get merged until after the fact.
struct dvb_pll_fcv1236d can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch:
- adds a missing error check and
- removes an error check that could never be true
Both spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the useless tuner field and avoids a double free of
the tuner (either mt2060 or qt1010).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.
This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
linux/dvb/video.h uses types __u32, __s32, etc., but does not include
any header defining those when __KERNEL__ is not defined.
Fix this by including asm/types.h when __KERNEL__ is not defined.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While I was busy compile-testing my patch, ENOSYS sneaked into pm.h
leading to some compile-breakages mostly on ia64 and some mips configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We ClearSlabDebug() before the last SlabDebug() check. Clear it later.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Ingo noticed that the SLUB code does include the lock debugging free
check.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
Commit 296699de6b broke building APM
support if CONFIG_PM_SLEEP is not set.
Reported by Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Simplified a bit as suggested by Rafael. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the m32r build after the commit "Remove fs.h from mm.h"
was merged (commit 4e950f6f01).
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
