My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect. It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.
This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect. This patch (as726)
fixes it.
From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: Matt Meno <mmeno@idealcorp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).
It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
did not go far enough
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed this while debugging something unrelated on
sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?
Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Compile fixes for au1200 ohci.
First part looks a bit hackish... but it works for me.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We all failed to notice that Franck's recent update to usb-storage allowed
an URB to complete after its context data was no longer valid. This patch
(as746) makes the driver wait for the URB to complete whenever there's a
timeout.
Although timeouts in usb-storage are relatively uncommon, they do occur.
Without this patch the code in 2.6.18-rc1 will fault within an interrupt
handler, which is not nice at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In usbfs's fs_remove_file() function, the aim is to remove a file or
directory from usbfs. This is done by first taking the i_mutex of the
parent directory of this file/dir via
mutex_lock(&parent->d_inode->i_mutex);
and then to call either usbfs_rmdir() for a directory or usbfs_unlink()
for a file. Both these functions then take the i_mutex for the
to-be-removed object themselves:
mutex_lock(&inode->i_mutex);
This is a classical parent->child locking order relationship that the VFS uses
all over the place; the VFS locking rule is "you need to take the parent
first". This patch annotates the usbfs code to make this explicit and thus
informs the lockdep code that those two locks indeed have this relationship.
The rules for unlink that we already use in the VFS for unlink are to use
I_MUTEX_PARENT for the parent directory, and a normal mutex for the file
itself; this patch follows that convention.
Has no effect on non-lockdep kernels.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
This patch updates the USB core to save and pass the sending task secid when
sending signals upon AIO completion so that proper security checking can be
applied by security modules.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes pxa2xx_udc.c to include asm/arch/udc.h again to fix current
build breakage.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
[ forwarded by David Brownell <david-b@pacbell.net> ]
[ fixed to apply properly by Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usually we don't care much about 'gcc -W' warnings, but some of us do build
kernels that way to look for problems, and then the fewer warnings we have
to wade through the better. Especially when they are very easy and
non-intrusive to clean up. Which is the case for the following warnings
spewed by drivers/usb/storage/usb.h :
drivers/usb/storage/usb.h:163: warning: `inline' is not at beginning of
+declaration
drivers/usb/storage/usb.h:166: warning: `inline' is not at beginning of
+declaration
There's also some precedence for cleaning up these warnings. I've had
a few patches merged in the past that remove exactly this class of
warnings.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a mispelling of the korean alphabet name in the input subsystem.
See http://en.wikipedia.org/wiki/Hangeul#Names for more details.
KEY_HANGUEL left to not break people
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 786dc1d3d7.
As Al so eloquently points out, the patch is crap. The old code was fine,
the new code was bogus.
It never dereferenced a user pointer, the "->" operator was to an array
member, which gives the _address_ of the member (in user space), not an
actual dereference at all.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.
Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for USB_ISP116X_HCD, USB_SL811_HCD and
USB_SL811_CS.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Yeah, it's a hack, but it is only temporary until Alan's patches
reworking this area make it in. We really should not care what devices
below us are doing, especially when we do not really know what type of
devices they are. This patch relies on the fact that the endpoint
devices do not have a driver assigned to us.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now /sys/class/usb is dynamically created when we have something to put
in it, and removed when all devices go away.
Just trying to cut down on the clutter in sysfs...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the usb class devices that control the usbfs nodes to show up
in the proper place in the larger device tree.
No userspace changes is needed, this is compatible due to the symlinks
generated by the driver core.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will allow for us to give endpoints a major/minor to create a
"usbfs2-like" way to access endpoints directly from userspace in an
easier manner than the current usbfs provides us.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
