Fix the problem that the following error message is sometimes displayed
at irq migration when vector domain is enabled.
"Unexpected interrupt vector %d on CPU %d is not mapped to any IRQ!"
The cause of this problem is an interrupt is sent to the previous
target CPU after cleaning up vector to irq mapping table. To clean up
vector to irq map on the previous target CPU safty, change the irq
migration in multiple vector domain as follows. The original idea is
from x86 interrupt management code.
- Delay vector to irq table cleanup until the interrupts are sent
to new target CPUs. By this, it is ensured that target CPU is
completely changed on the interrupt controller side.
- Even after the interrupts are sent to new target CPUs, there can
be pended interrupts remaining on the previous target CPU. So we
need to delay clearning up vector to irq table until the pended
interrupt is handled. For this, send IPI to the previous target
CPU with lower priority vector and clean up vector to irq table
in its handler.
This patch affects only to irq migration code with multiple vector
domain is enabled.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The similar check has been added to x86_32(i386) in commit
id 83bd01024b.
So we add this check to ia64 and improve it a liitle bit in that
we need to check for stack overflow only when the signal is on stack.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch implements VIRT_CPU_ACCOUNTING for ia64,
which enable us to use more accurate cpu time accounting.
The VIRT_CPU_ACCOUNTING is an item of kernel config, which s390
and powerpc arch have. By turning this config on, these archs
change the mechanism of cpu time accounting from tick-sampling
based one to state-transition based one.
The state-transition based accounting is done by checking time
(cycle counter in processor) at every state-transition point,
such as entrance/exit of kernel, interrupt, softirq etc.
The difference between point to point is the actual time consumed
during in the state. There is no doubt about that this value is
more accurate than that of tick-sampling based accounting.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix large MCA bootmem allocation
[IA64] Simplify cpu_idle_wait
[IA64] Synchronize RBS on PTRACE_ATTACH
[IA64] Synchronize kernel RSE to user-space and back
[IA64] Rename TIF_PERFMON_WORK back to TIF_NOTIFY_RESUME
[IA64] Wire up timerfd_{create,settime,gettime} syscalls
The MCA code allocates bootmem memory for NR_CPUS, regardless
of how many cpus the system actually has. This change allocates
memory only for cpus that actually exist.
On my test system with NR_CPUS = 1024, reserved memory was reduced by 130944k.
Before: Memory: 27886976k/28111168k available (8282k code, 242304k reserved, 5928k data, 1792k init)
After: Memory: 28017920k/28111168k available (8282k code, 111360k reserved, 5928k data, 1792k init)
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is just Venki's patch[*] for x86 ported to ia64.
* http://marc.info/?l=linux-kernel&m=120249201318159&w=2
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When attaching to a stopped process, the RSE must be explicitly
synced to user-space, so the debugger can read the correct values.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
CC: Roland McGrath <roland@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is base kernel patch for ptrace RSE bug. It's basically a backport
from the utrace RSE patch I sent out several weeks ago. please review.
when a thread is stopped (ptraced), debugger might change thread's user
stack (change memory directly), and we must avoid the RSE stored in
kernel to override user stack (user space's RSE is newer than kernel's
in the case). To workaround the issue, we copy kernel RSE to user RSE
before the task is stopped, so user RSE has updated data. we then copy
user RSE to kernel after the task is resummed from traced stop and
kernel will use the newer RSE to return to user.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
CC: Roland McGrath <roland@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since the RSE synchronization will need a TIF_ flag, but all
work-to-be-done bits are already used, so we have to multiplex
TIF_NOTIFY_RESUME again.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix typo in comments.
BTW: I have to fix coding style in arch/ia64/kernel/time.c also, otherwise
checkpatch.pl will be complaining.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the configuration dependencies in the vmcoreinfo data.
i386's "node_data" is defined in arch/x86/mm/discontig_32.c,
and x86_64's one is defined in arch/x86/mm/numa_64.c.
They depend on CONFIG_NUMA:
arch/x86/mm/Makefile_32:7
obj-$(CONFIG_NUMA) += discontig_32.o
arch/x86/mm/Makefile_64:7
obj-$(CONFIG_NUMA) += numa_64.o
ia64's "pgdat_list" is defined in arch/ia64/mm/discontig.c,
and it depends on CONFIG_DISCONTIGMEM and CONFIG_SPARSEMEM:
arch/ia64/mm/Makefile:9-10
obj-$(CONFIG_DISCONTIGMEM) += discontig.o
obj-$(CONFIG_SPARSEMEM) += discontig.o
ia64's "node_memblk" is defined in arch/ia64/mm/numa.c,
and it depends on CONFIG_NUMA:
arch/ia64/mm/Makefile:8
obj-$(CONFIG_NUMA) += numa.o
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset is for the vmcoreinfo data.
The vmcoreinfo data has the minimum debugging information only for dump
filtering. makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.
This patch:
VMCOREINFO_SIZE() should be renamed VMCOREINFO_STRUCT_SIZE() since it's always
returning the size of the struct with a given name. This change would allow
VMCOREINFO_TYPEDEF_SIZE() to simply become VMCOREINFO_SIZE() since it need not
be used exclusively for typedefs.
This discussion is the following:
http://www.ussg.iu.edu/hypermail/linux/kernel/0709.3/0582.html
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
calibrate_delay() must be __cpuinit, not __{dev,}init.
I've verified that this is correct for all users.
While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>
This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:
WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] make pfm_get_task work with virtual pids
[IA64] honor notify_die() returning NOTIFY_STOP
[IA64] remove dead code: __cpu_{down,die} from !HOTPLUG_CPU
[IA64] Appoint kvm/ia64 Maintainers
[IA64] ia64_set_psr should use srlz.i
[IA64] Export three symbols for module use
[IA64] mca style cleanup
[IA64] sn_hwperf semaphore to mutex
[IA64] generalize attribute of fsyscall_gtod_data
[IA64] efi.c Add /* never reached */ annotation
[IA64] efi.c Spelling/punctuation fixes
[IA64] Make efi.c mostly fit in 80 columns
[IA64] aliasing-test: fix gcc warnings on non-ia64
[IA64] Slim-down __clear_bit_unlock
[IA64] Fix the order of atomic operations in restore_previous_kprobes on ia64
[IA64] constify function pointer tables
[IA64] fix userspace compile error in gcc_intrin.h
This is the new timerfd API as it is implemented by the following patch:
int timerfd_create(int clockid, int flags);
int timerfd_settime(int ufd, int flags,
const struct itimerspec *utmr,
struct itimerspec *otmr);
int timerfd_gettime(int ufd, struct itimerspec *otmr);
The timerfd_create() API creates an un-programmed timerfd fd. The "clockid"
parameter can be either CLOCK_MONOTONIC or CLOCK_REALTIME.
The timerfd_settime() API give new settings by the timerfd fd, by optionally
retrieving the previous expiration time (in case the "otmr" parameter is not
NULL).
The time value specified in "utmr" is absolute, if the TFD_TIMER_ABSTIME bit
is set in the "flags" parameter. Otherwise it's a relative time.
The timerfd_gettime() API returns the next expiration time of the timer, or
{0, 0} if the timerfd has not been set yet.
Like the previous timerfd API implementation, read(2) and poll(2) are
supported (with the same interface). Here's a simple test program I used to
exercise the new timerfd APIs:
http://www.xmailserver.org/timerfd-test2.c
[akpm@linux-foundation.org: coding-style cleanups]
[akpm@linux-foundation.org: fix ia64 build]
[akpm@linux-foundation.org: fix m68k build]
[akpm@linux-foundation.org: fix mips build]
[akpm@linux-foundation.org: fix alpha, arm, blackfin, cris, m68k, s390, sparc and sparc64 builds]
[heiko.carstens@de.ibm.com: fix s390]
[akpm@linux-foundation.org: fix powerpc build]
[akpm@linux-foundation.org: fix sparc64 more]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This pid comes from user space, so treat it accordingly.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This requires making die() and die_if_kernel() return a value, and their
callers to honor this (and be prepared that it returns).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Neither __cpu_down() nor __cpu_die() are being referenced without
CONFIG_HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The only in kernel use of ia64_set_psr() needs to follow
it with a srlz.i (since it is changing state for PSR.ic).
So it is pointless to issue srlz.d inside this function.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since kvm/module needs to use some unexported functions in kernel,
so export them with this patch.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In an ordinary way,
> } __attribute__ ((aligned (L1_CACHE_BYTES)));
should be
> } ____cacheline_aligned;
to save some bytes on an uni-processor.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As written, this loop could be for (;;) instead of do while (md). The tests
inside the loop always result in a return so the loop never terminates normally.
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Incorporates the suggestions from Peter Chubb the last time I submitted
this. This called for using the same verb tense in the couple of preceding
comments as well.
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is purely whitespace changes to make the code fit in 80
columns, plus fix some inconsistent indentation. The efi_guidcmp()
tests remain wider than 80-columns since that seems to be the most
clear.
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the order of atomic operations to prevent overwriting prev_kprobe[0].
To pop values from stack, we must decrement stack index right AFTER
reading values.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ACPI_PDC_SMP_T_SWCOORD bit is set by and OS that is capable of
native ACPI throttling software coordination for mutli-processors
using the _TSD information.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'task_killable' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc: (22 commits)
Remove commented-out code copied from NFS
NFS: Switch from intr mount option to TASK_KILLABLE
Add wait_for_completion_killable
Add wait_event_killable
Add schedule_timeout_killable
Use mutex_lock_killable in vfs_readdir
Add mutex_lock_killable
Use lock_page_killable
Add lock_page_killable
Add fatal_signal_pending
Add TASK_WAKEKILL
exit: Use task_is_*
signal: Use task_is_*
sched: Use task_contributes_to_load, TASK_ALL and TASK_NORMAL
ptrace: Use task_is_*
power: Use task_is_*
wait: Use TASK_NORMAL
proc/base.c: Use task_is_*
proc/array.c: Use TASK_REPORT
perfmon: Use task_is_*
...
Fixed up conflicts in NFS/sunrpc manually..
percpu_modcopy() is defined multiple times in arch files. However, the only
user is module.c. Put a static definition into module.c and remove
the definitions from the arch files.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- add support for PER_CPU_ATTRIBUTES
- fix generic smp percpu_modcopy to use per_cpu_offset() macro.
Add the ability to use generic/percpu even if the arch needs to override
several aspects of its operations. This will enable the use of generic
percpu.h for all arches.
An arch may define:
__per_cpu_offset Do not use the generic pointer array. Arch must
define per_cpu_offset(cpu) (used by x86_64, s390).
__my_cpu_offset Can be defined to provide an optimized way to determine
the offset for variables of the currently executing
processor. Used by ia64, x86_64, x86_32, sparc64, s/390.
SHIFT_PTR(ptr, offset) If an arch defines it then special handling
of pointer arithmentic may be implemented. Used
by s/390.
(Some of these special percpu arch implementations may be later consolidated
so that there are less cases to deal with.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The compiler team did the hard work for this distilling a problem in
large fortran application which showed up when applied to a 290MB input
data set down to this instruction:
ldfd f34=[r17],-8
Which they noticed incremented r17 by 0x10 rather than decrementing it
by 8 when the value in r17 caused an unaligned data fault. I tracked
it down to some bad instruction decoding in unaligned.c. The code
assumes that the 'x' bit can determine whether the instruction is
an "ldf" or "ldfp" ... which it is for opcode=6 (see table 4-29 on
page 3:302 of the SDM). But for opcode=7 the 'x' bit is irrelevent,
all variants are "ldf" instructions (see table 4-36 on page 3:306).
Note also that interpreting the instruction as "ldfp" means that the
"paired" floating point register (f35 in the example here) will also
be corrupted.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently CMCI mask of hot-added CPU is always disabled after CPU hotplug.
We should adjust this mask depending on CMC polling state.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an unused variable warning in mm/vmalloc.c.
Tony: also fix resulting fallout in uncached.c with a
typo in args to flush_tlb_kernel_range().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following assembler warning messages.
AS arch/ia64/kernel/head.o
arch/ia64/kernel/head.S: Assembler messages:
arch/ia64/kernel/head.S:1179: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1179: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
arch/ia64/kernel/head.S:1180: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1180: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
:
arch/ia64/kernel/head.S:1213: Warning: Use of 'ldf.fill.nta' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1213: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following compiler warning messages.
CC arch/ia64/kernel/irq_ia64.o
arch/ia64/kernel/irq_ia64.c: In function 'create_irq':
arch/ia64/kernel/irq_ia64.c:343: warning: 'domain.bits[0u]' may be used uninitialized in this function
arch/ia64/kernel/irq_ia64.c: In function 'assign_irq_vector':
arch/ia64/kernel/irq_ia64.c:203: warning: 'domain.bits[0u]' may be used uninitialized in this function
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I tried to upgrade an IA32 chroot on my IA64 to a new glibc with TLS.
It kept dying because set_thread_area was returning -ESRCH
(bugs.debian.org/451939).
I instrumented arch/ia64/ia32/sys_ia32.c:get_free_idx() and ended up
seeing output like
[pid] idx desc->a desc->b
-----------------------------
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> 0 0
[2710] 2 -> 0 0
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> c6b0ffff 40dff31b
[2710] 2 -> 0 0
[2711] 0 -> c6b0ffff 40dff31b
[2711] 1 -> c6b0ffff 40dff31b
[2711] 2 -> 48c0ffff 40dff317
which suggested to me that TLS pointers were surviving exec() calls,
leading to GDT pointers filling up and the eventual failure of
get_free_idx().
I think the solution is flushing the tls array on exec.
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64 oops message doesn't include the kernel version, which
makes it hard to automatically categorize oops messages scraped
from mailing lists and bug databases.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some redundant code in the function setup_sigcontext().
The registers ar.ccv,b7,r14,ar.csd,ar.ssd,r2-r3 and r16-r31 are not
restored in restore_sigcontext() when (flags & IA64_SC_FLAG_IN_SYSCALL) is
true. So we don't need to zero those variables in setup_sigcontext().
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ACPI tables follow a tree structure in memory.
The root of the tree is the RSDP (Root System Description Pointer).
To find the RSDP, the OS searches for the signature "RSD PTR "
in well known physical memory locations. Then the OS computes
a table checksum to verify that the signature is really part
of a valid table header.
Some systems have a proper signature but an invalid checksum;
followed elsewhere by a proper signature with valid checksum.
http://bugzilla.kernel.org/show_bug.cgi?id=9444
The Linux RSDP scanning code bailed out on those systems
and as a result they booted with ACPI disabled.
Fix this by deleting the Linux RSDP scanning code and
plugging in the ACPICA RSDP scanning code.
Signed-off-by: Len Brown <len.brown@intel.com>
.. as it it used only during early boot.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
arch/ia64/kernel/acpi.c | 2 +-
arch/x86/kernel/acpi/boot.c | 4 ++--
drivers/acpi/osl.c | 3 ++-
3 files changed, 5 insertions(+), 4 deletions(-)
Signed-off-by: Len Brown <len.brown@intel.com>
If "CPEI Processor Override" bit is not set in "Platform Interrupt
Source Flags" in "Platform Interrupt Sources Structure" in ACPI MADT,
the target processor of CPEI is restricted to a specific CPU. Because
of this, the delivery mode for CPEI should be IOSAPIC_FIXED.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Restore regs->ccr_iip before kreturn probe handler runs. In this way, if
probe handler does unwind, unwind can correctly get the stack trace.
Fixes: http://sourceware.org/bugzilla/show_bug.cgi?id=5051
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
'!' has a higher priority than '&', so as was
this won't test the first bit, but rather evaluates to false for any non-zero
lsapic->lapic_flags.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Macro efi_md_size is defined in efi.c, and here we apply it throughout
efi.c.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rename _bss to __bss_start as on other architectures. That makes it
possible to use the <linux/sections.h> instead of own declarations. Also
add __bss_stop because that symbol exists on other architectures.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make some IOSAPIC functions static and remove one that is unused.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not all the return value of __copy_from_user and
__put_user is checked.This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the unionfs patch applied I get
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
the other architectures (some, at least) export copy_page() so I guess ia64
should also do so.
To do this we need to move the copy_page() functions out of lib.a and into
built-in.o and add the EXPORT_SYMBOL().
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/ia64-unknown-linux-gnu/lib/gcc/ia64-unknown-linux-gnu/3.4.5/../../../../ia64-unknown-linux-gnu/bin/ld: section .data.patch [a000000000000500 -> a000000000000507] overlaps section .dynamic [a0000000000003c8 -> a000000000000507]
This only appears to be a problem with strangely configured
cross-compilation ... native compilers don't have this issue.
But in the interests of helping others at least compile for
ia64, this can go in. -Tony
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
i386 and x86-64 registers System RAM as IORESOURCE_MEM | IORESOURCE_BUSY.
But ia64 registers it as IORESOURCE_MEM only.
In addition, memory hotplug code registers new memory as IORESOURCE_MEM too.
This difference causes a failure of memory unplug of x86-64. This patch
fixes it.
This patch adds IORESOURCE_BUSY to avoid potential overlap mapping by PCI
device.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Luck, Tony" <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Altix (sn2) machines the "Error parsing MADT" message is
misleading because the lack of IOSAPIC entries is expected.
Since I am sure someone will ask, I have been told that
the chance of this changing anytime soon is close to nil.
Signed-off-by: George Beshers <gbeshers@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Newer Itanium versions have added additional processor feature set
bits. This patch prints all the implemented feature set bits. Some
bit descriptions have not been made public. For those bits, a generic
"Feature set X bit Y" message is printed. Bits that are not implemented
will no longer be printed.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that redirect hit bit in I/O SAPIC RTE is set even
when it must be disabled (e.g. nointroute boot option is set, CPU
hotplug is enabled or percpu vector is enabled).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clean up /proc/interrupts output on the system that has 10 or more
CPUs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the CPE handler encounters too many CPEs (such as a solid single
bit memory error), it sets up a polling timer and disables the CPE
interrupt (to avoid excessive overhead logging the stream of single
bit errors). disable_irq_nosync() calls chip->disable() to provide
a chipset specifiec interface for disabling the interrupt. This patch
adds the Altix specific support to disable and re-enable the CPE interrupt.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
No need to print "McKinley Errata 9 workaround not needed; disabling it"
on every non-McKinley Itanium, which at this point is almost all of them.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
If you build the kernel `in-place' then do a git update, git
complains about arch/ia64/kernel/gate.lds being modified and
untracked.
Add that (generated) file to a .gitignore file.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not sizeof(ptr) ... we meant to say sizeof(*ptr).
Also moved the memset to the error path (the normal path overwrites
every field in the structure anyway) -Tony
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
New sanity checks in sysctl_check_table() complain about a couple
of mode 0755 that should be 0555 in the perfmon code:
sysctl table check failed: /kernel .1 Writable sysctl directory
sysctl table check failed: /kernel/perfmon Writable sysctl directory
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that pci_enable_msi() fails on ia64 platform. The cause of
this problem is incorrect return value of ia64_setup_msi_irq(). It must
return 0 on success, instead of irq number.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clean up the process for presenting the "physical id" field in
/proc/cpuinfo.
- remove global smp_num_cpucores, as it is mostly useless
- remove check_for_logical_procs(), since we do the same
functionality in identify_siblings()
- reflow logic in identify_siblings(). If an older CPU
does not implement PAL_LOGICAL_TO_PHYSICAL, we may still
be able to get useful information from SAL_PHYSICAL_ID_INFO
- in identify_siblings(), threads/cores are a property of
the CPU, not the platform
- remove useless printk's about multi-core / thread
capability in identify_siblings(), as that information
is readily available in /proc/cpuinfo, and printing for
the BSP only adds little value
- smp_num_siblings is now meaningful if any CPU in the
system supports threads, not just the BSP
- expose "physical id" field, even on CPUs that are not
multi-core / multi-threaded (as long as we have a valid
value). Now we know what sockets Madisons live in too.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When gcc uses --build-id by default, the gate.lds.S linker script runs afoul
of the new note section and produces a bad DSO image. This fixes it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
vmcore_find_descriptor_size() is only called by
reserve_elfcorehdr(), which is in __init, so it seems to me that
vmcore_find_descriptor_size() should be there too.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add the BSS to the resource tree just as kernel text and kernel data are in
the resource tree. The main reason behind this is to avoid crashkernel
reservation in that area.
While it's not strictly necessary to have the BSS in the resource tree (the
actual collision detection is done in the reserve_bootmem() function before),
the usage of the BSS resource should be presented to the user in /proc/iomem
just as Kernel data and Kernel code.
Note: The patch currently is only implemented for x86 and ia64 (because
efi_initialize_iomem_resources() has the same signature on i386 and ia64).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adapts IA64 to use the generic parse_crashkernel() function instead
of its own parsing for the crashkernel command line.
Because the total amount of System RAM must be known when calling this
function, efi_memmap_init() is modified to return its accumulated total_memory
variable.
Also, the crashkernel handling is moved in an own function in
arch/ia64/kernel/setup.c to make the code more readable.
[kamalesh@linux.vnet.ibm.com: build fix]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the largest patch in the set. Make all (I hope) the places where
the pid is shown to or get from user operate on the virtual pids.
The idea is:
- all in-kernel data structures must store either struct pid itself
or the pid's global nr, obtained with pid_nr() call;
- when seeking the task from kernel code with the stored id one
should use find_task_by_pid() call that works with global pids;
- when showing pid's numerical value to the user the virtual one
should be used, but however when one shows task's pid outside this
task's namespace the global one is to be used;
- when getting the pid from userspace one need to consider this as
the virtual one and use appropriate task/pid-searching functions.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: yet nuther build fix]
[akpm@linux-foundation.org: remove unneeded casts]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Paul Menage <menage@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On platforms that copy sys_tz into the vdso (currently only x86_64, soon to
include powerpc), it is possible for the vdso to get out of sync if a user
calls (admittedly unusual) settimeofday(NULL, ptr).
This patch adds a hook for architectures that set
CONFIG_GENERIC_TIME_VSYSCALL to ensure when sys_tz is updated they can also
updatee their copy in the vdso.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/ia64/kernel/machine_kexec.c: In function `arch_crash_save_vmcoreinfo':
arch/ia64/kernel/machine_kexec.c:131: error: `pgdat_list' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:131: error: (Each undeclared identifier is reported only once
arch/ia64/kernel/machine_kexec.c:131: error: for each function it appears in.)
arch/ia64/kernel/machine_kexec.c:134: error: `node_memblk' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:135: error: `NR_NODE_MEMBLKS' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:136: error: invalid application of `sizeof' to incomplete type `node_memblk_s'
arch/ia64/kernel/machine_kexec.c:137: error: dereferencing pointer to incomplete type
arch/ia64/kernel/machine_kexec.c:138: error: dereferencing pointer to incomplete type
make[1]: *** [arch/ia64/kernel/machine_kexec.o] Error 1
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a prefix "VMCOREINFO_" to the vmcoreinfo macros. Old vmcoreinfo macros
were defined as generic names SYMBOL/SIZE/OFFSET /LENGTH/CONFIG, and it is
impossible to grep for them. So these names should be changed. This
discussion is the following:
http://www.ussg.iu.edu/hypermail/linux/kernel/0709.1/0415.html
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch set frees the restriction that makedumpfile users should install a
vmlinux file (including the debugging information) into each system.
makedumpfile command is the dump filtering feature for kdump. It creates a
small dumpfile by filtering unnecessary pages for the analysis. To
distinguish unnecessary pages, it needs a vmlinux file including the debugging
information. These days, the debugging package becomes a huge file, and it is
hard to install it into each system.
To solve the problem, kdump developers discussed it at lkml and kexec-ml. As
the result, we reached the conclusion that necessary information for dump
filtering (called "vmcoreinfo") should be embedded into the first kernel file
and it should be accessed through /proc/vmcore during the second kernel.
(http://www.uwsg.iu.edu/hypermail/linux/kernel/0707.0/1806.html)
Dan Aloni created the patch set for the above implementation.
(http://www.uwsg.iu.edu/hypermail/linux/kernel/0707.1/1053.html)
And I updated it for multi architectures and memory models.
(http://lists.infradead.org/pipermail/kexec/2007-August/000479.html)
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
d5a7430ddc missed a spot where we
use cpu_sibling_map and cpu_core_map. These don't exist on a
uni-processor build. Wrap #ifdef CONFIG_SMP ... #endif around it.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce architecture dependent kretprobe blacklists to prohibit users
from inserting return probes on the function in which kprobes can be
inserted but kretprobes can not.
This patch also removes "__kprobes" mark from "__switch_to" on x86_64 and
registers "__switch_to" to the blacklist on x86-64, because that mark is to
prohibit user from inserting only kretprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The checks for node_online in the uncached allocator are made to make sure
that memory is available on these nodes. Thus switch all the checks to use
N_HIGH_MEMORY and to N_ONLINE.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Bob Picco <bob.picco@hp.com>
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@skynet.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert cpu_sibling_map from a static array sized by NR_CPUS to a per_cpu
variable. This saves sizeof(cpumask_t) * NR unused cpus. Access is mostly
from startup and CPU HOTPLUG functions.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the problem that kdump on INIT hung up if kdump kernel image is
not configured.
The kdump_init_notifier() on monarch CPU stops its operation at
DIE_INIT_MONARCH_LEAVE time if the kdump kernel image is not
configured. On the other hand, kdump_init_notifier() on non-monarch
CPUs get into spin because they don't know the fact the monarch stops
its operation. This is the cause of this problem. To fix this problem,
we need to check the kdump kernel image at the top of the
kdump_init_notifier() function.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that kdump on INIT causes a kernel panic if kdump
kernel image is not configured. The cause of this problem is
machine_kexec_on_init() is using printk in INIT context. It should
use ia64_mca_printk() instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The use of vector in ia64_machine_kexec() seems spurious,
and removing it simplifies the code slightly.
As suggested by Alex Williamson <alex.williamson@hp.com>
Cc: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Additional testing uncovered a situation where the MCA recovery code could
hang due to a race condition.
According to the SAL spec, SAL sends a rendezvous interrupt to all but the first
CPU that goes into MCA. This includes other CPUs that go into MCA at the same
time. Those other CPUs will go into the linux MCA handler (rather than the
slave loop) with the rendezvous interrupt pending. When all the CPUs have
completed MCA processing and the last monarch completes, freeing all the CPUs,
the CPUs with the pended rendezvous interrupt then go into the
ia64_mca_rendez_int_handler(). In ia64_mca_rendez_int_handler() the CPUs
get marked as rendezvoused, but then leave the handler (due to no MCA).
That leaves the CPUs marked as rendezvoused _before_ the next MCA event.
When the next MCA hits, the monarch will mistakenly believe that all the CPUs
are rendezvoused when they are not, opening up a window where a CPU can get
stuck in the slave loop.
This patch avoids leaving CPUs marked as rendezvoused when they are not.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While testing the MCA recovery code, noticed that some machines would have a
five second delay rendezvousing cpus. What was happening is that
ia64_wait_for_slaves() would check to see if all the slave CPUs had
rendezvoused. If any had not, it would wait 1 millisecond then check again.
If any CPUs had still not rendezvoused, it would wait 5 seconds before
checking again.
On some configs the rendezvous takes more than 1 millisecond, causing the code
to wait the full 5 seconds, even though the last CPU rendezvoused after only
a few milliseconds.
The fix is to check every 1 millisecond to see if all the cpus have
rendezvoused. After 5 seconds the code concludes the CPUs will never
rendezvous (same as before).
The MCA code is, by definition, not performance critical, but a needless
delay of 5 seconds is senseless. The 5 seconds also adds up quickly
when running the error injection code in a loop.
This patch both simplifies the code and removes the needless delay.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because it is dead code and not referenced by anybody else (that file cannot
be built modular).
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* palinfo.c:
palinfo_cpu_notifier is a CPU hotplug notifier_block, and can be
marked __cpuinitdata, and the callback function palinfo_cpu_callback()
itself can be marked __cpuinit. create_palinfo_proc_entries() is only
called from __cpuinit callback or general __init code, therefore a
candidate for __cpuinit itself. remove_palinfo_proc_entries() is only
called from __cpuinit callback or general __exit code, therefore a
candidate for __cpuexit.
* salinfo.c:
The CPU hotplug notifier_block can be __cpuinitdata. The callback
salinfo_cpu_callback() is incorrectly marked __devinit -- it must
be __cpuinit instead.
* topology.c:
cache_sysfs_init() is only called at device_initcall() time so marking
it as __cpuinit is wrong and wasteful. It should be unconditionally
__init. Also cleanup reference to hotplug notifier callback function
from this function and replace with cache_add_dev(), which could also
enable us to use other tricks to replace __cpuinit{data} annotations,
as recently discussed on this list.
cache_shared_cpu_map_setup() is only ever called from __cpuinit-marked
functions hence both its definitions (SMP or !SMP) are candidates for
__cpuinit itself. Also all_cpu_cache_info can be __cpuinitdata because
only referenced from __cpuinit code.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
When PTRACE_SYSCALL was used and then PTRACE_DETACH is used, the
TIF_SYSCALL_TRACE flag is left set on the formerly-traced task. This
means that when a new tracer comes along and does PTRACE_ATTACH, it's
possible he gets a syscall tracing stop even though he's never used
PTRACE_SYSCALL. This happens if the task was in the middle of a system
call when the second PTRACE_ATTACH was done. The symptom is an
unexpected SIGTRAP when the tracer thinks that only SIGSTOP should have
been provoked by his ptrace calls so far.
A few machines already fixed this in ptrace_disable (i386, ia64, m68k).
But all other machines do not, and still have this bug. On x86_64, this
constitutes a regression in IA32 compatibility support.
Since all machines now use TIF_SYSCALL_TRACE for this, I put the
clearing of TIF_SYSCALL_TRACE in the generic ptrace_detach code rather
than adding it to every other machine's ptrace_disable.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up the `enable early console for SKI' patch
(471e7a4484), and
1. potentially allows the gensparse_defconfig to work again.
(there are other problems running a generic kernel on Ski)
2. fixes the `console registered twice' problem.
3. Cleans up the code by moving the `extern hpsim_cons' declaration to
a new asm/hpsim.h file.
Thanks to Jes for comments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add additional support for CPU disable on SN platforms.
Correctly setup the smp_affinity mask for I/O error IRQs.
Restrict the use of the feature to Altix 4000 and 450 systems
running with a CPU disable capable PROM, and do not allow disabling
of CPU 0.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The pending interrupts can be remaining at boot up time on some
platform. This will cause spurious interrupts when interrupt is
enabled for the first time. This patch clears IVR at the CPU
initialization to eliminate such spurious interrupts.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix handling for spurious interrupts not being mapped to any IRQs.
Currently, spurious interrupts that are not mapped to any IRQs are
handled as IRQ 15 (== IA64_SPURIOUS_VECTOR). But it is not proper
because vector != irq. We need special handlings for such spurious
interrupts not being mapped to any IRQs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When using Ski to debug early startup, it's a bit of a pain not to
have printk.
This patch enables the simulated console very early.
It may be worth conditionalising on the command line... but this is
enough for now.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The "ri" field in the processor status register only has defined
values of 0, 1, 2. Do not let ptrace set this to 3. As with
other reserved fields in registers we silently discard the value.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The core cpufreq code doesn't appear to understand returning -EAGAIN
for the get() function of the cpufreq_driver. If PAL_GET_PSTATE returns
-1, such as when running on Xen, scaling_cur_freq is happy to return
4294967285 kHz (ie. (unsigned)-11). The other drivers appear to return
0 for a failure, and doing so gives me the max frequency from
scaling_cur_frequency and "<unknown>" from cpuinfo_cur_frequency. I
believe that's the desired behavior.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Explicitly put the unwind section into its own program-header. This
used to be unnecessary (probably because binutils did it for us), but
with current binutils (e.g., v2.17.50.20070804) we won't get
the PT_IA_64_UNWIND header without this patch which will break
unwinding in a debugger and simulators such as Ski.
Signed-off-by: David Mosberger-Tang <dmosberger@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add NOTES to linker script such that the kernel can be built with
recent versions of binutils. Without this patch, final link fails
with this error:
ld: .tmp_vmlinux1: section `.text' can't be allocated in segment 0
ld: final link failed: Bad value
This error is due to the fact that the --build-id option is used
with newer linkers to include a .notes section on the kernel, but
without the NOTES macro, that section won't be included in the kernel
which then leads to the above error message.
Signed-off-by: David Mosberger-Tang <dmosberger@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use local_vector_to_irq() instead of looping through all NR_IRQS.
This avoids registering the CPE handler on multiple irqs. Only
register if the irq is valid. If no valid irq is found, print an
error message and set up polling.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add base support for implementing platform_irq_to_vector(), and
then use it on SN2.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While sending interrupts to a cpu to repeatedly wake a thread, on occasion
that thread will take a full timer tick cycle (4002 usec in my case)
to wakeup.
The problem concerns a race condition in the code around the safe_halt()
call in the default_idle() routine. Setting 'nohalt' on the kernel
command line causes the long wakeups to disappear.
void
default_idle (void)
{
local_irq_enable();
while (!need_resched()) {
--> if (can_do_pal_halt)
--> safe_halt();
else
A timer tick could arrive between the check for !need_resched and the
actual call to safe_halt() (which does a pal call to PAL_HALT_LIGHT).
By the time the timer tick completes, a thread that might now need to run
could get held up for as long as a timer tick waiting for the halted cpu.
I'm proposing that we disable irq's and check need_resched again before
calling safe_halt(). Does anyone see any problem with this approach?
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] ITC: Reduce rating for ITC clock if ITCs are drifty
[IA64] SN2: Fix up sn2_rtc clock
[IA64] Fix wrong access to irq_desc[] in iosapic_register_intr().
[IA64] Fix possible race in destroy_and_reserve_irq()
[IA64] Fix registered interrupt check
[IA64] Remove a few duplicate includes
[IA64] Allow smp_call_function_single() to current cpu
[IA64] fix a few section mismatch warnings
Make sure to reduce the rating of the ITC clock if ITCs are drifty. If they
are drifting then we have not synchronized the ITC values, nor are we doing
the jitter compensation (useless since drift may increase the differentials
arbitrarily).
Without this patch it is possible that the ITC clock becomes selected as
the system clock on systems with drifty ITCs which will result in
nanosleep hanging.
One can still select the itc clock manually on such systems via
clocksource=itc
(Produces nice hangs on SGI Altix.)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In error path we must unlock irq_desc[irq].lock before we change
'irq'.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, destroy_and_reserve_irq() sets irq_status[irq] UNUSED using
clear_irq_vector() and sets irq_status[irq] RSVD using reserve_irq().
But there is a race window because vector_lock is once released between
them. This patch fixes this race window.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that interrupts are not initialized correctly at PCI
hotplug or driver reloading time.
By vector domain change, the iosapic_rte_info structure was changed to
be on the iosapic_intr_info[irq].rtes list even after the interrupts
are unregistered. So iosapic_intr_info[irq].rtes list must not be
checked to see if there are registered interrupts (RTEs) on the
irq. We must check iosapic_intr_info[irq].count counter instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes a few duplicate includes from arch/ia64/
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the following section mismatch warnings:
WARNING: vmlinux.o(.text+0x41902): Section mismatch: reference to .init.text:__alloc_bootmem (between 'ia64_mca_cpu_init' and 'ia64_do_tlb_purge')
WARNING: vmlinux.o(.text+0x49222): Section mismatch: reference to .init.text:__alloc_bootmem (between 'register_intr' and 'iosapic_register_intr')
WARNING: vmlinux.o(.text+0x62beb2): Section mismatch: reference to .init.text:__alloc_bootmem_node (between 'hubdev_init_node' and 'cnodeid_get_geoid')
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix wrong return value in parse_vector_domain().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64's acpi_gsi_to_irq() function assumes irq == vector. But in
fact irq can be different from vector. This patch fix this wrong
assumption.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add some sanity checks into __bind_irq_vector().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
u32* volatile cyclone_timer means volatile auto pointer to u32,
which is clearly not what had been intended (we never even take
the address of that variable, let alone pass it to something that
could change it behind our back). u32 volatile * is what the
authors apparently wanted to say, but in reality we don't need that
qualifier there at all - it's (properly) only passed to iomem helpers
which takes care of that stuff just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Nail two more simple section mismatch errors
[IA64] fix section mismatch warnings
[IA64] rename partial_page
[IA64] Ensure that machvec is set up takes place before serial console
[IA64] vector-domain - fix vector_table
[IA64] vector-domain - handle assign_irq_vector(AUTO_ASSIGN)
pcibios_setup (between 'pci_setup' and 'quirk_mellanox_tavor')
setup_profiling_timer (between 'write_profile' and 'delayed_put_task_struct')
Signed-off-by: Tony Luck <tony.luck@intel.com>
In 741f98fe29 Sam added full
checking across the entire vmlinux image. This flushed out
a dozen new section mismatch warnings. Start the whack-a-mole
game again to stomp them out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jens has added a partial_page thing in splice whcih conflicts with the ia64
one. Rename ia64 out of the way. (ia64 chose poorly).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Parse the machvec command line option outside of the early_param()
so that ia64_mv is set before any console intialisation that
may result from early_param parsing.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This change fixes a panic when assign_irq_vector(irq) is called with
irq = AUTO_ASSIGN.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As it was a synonym for (CONFIG_ACPI && CONFIG_X86),
the ifdefs for it were more clutter than they were worth.
For ia64, just add a few stubs in anticipation of future
S3 or S4 support.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Prevent people from directly including <asm/rwsem.h>.
[IA64] remove time interpolator
[IA64] Convert to generic timekeeping/clocksource
[IA64] refresh some config files for 64K pagesize
[IA64] Delete iosapic_free_rte()
[IA64] fallocate system call
[IA64] Enable percpu vector domain for IA64_DIG
[IA64] Enable percpu vector domain for IA64_GENERIC
[IA64] Support irq migration across domain
[IA64] Add support for vector domain
[IA64] Add mapping table between irq and vector
[IA64] Check if irq is sharable
[IA64] Fix invalid irq vector assumption for iosapic
[IA64] Use dynamic irq for iosapic interrupts
[IA64] Use per iosapic lock for indirect iosapic register access
[IA64] Cleanup lock order in iosapic_register_intr
[IA64] Remove duplicated members in iosapic_rte_info
[IA64] Remove block structure for locking in iosapic.c
This is a merge of Peter Keilty's initial patch (which was
revived by Bob Picco) for this with Hidetoshi Seto's fixes
and scaling improvements.
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
> arch/ia64/kernel/iosapic.c:597: warning: 'iosapic_free_rte' defined but not used
>
> This isn't spurious, the only call to iosapic_free_rte() has been removed, but there
> is still a call to iosapic_alloc_rte() ... which means we must have a memory leak.
I did it on purpose (and gave the warning a miss...) and I consider
iosapic_free_rte() is no longer needed.
I decided to remain iosapic_rte_info to keep gsi-to-irq binding
after device disable. Indeed it needs some extra memory, but it
is only "sizeof(iosapic_rte_info) * <the number of removed devices>"
bytes and has no memory leak becasue re-enabled devices use the
iosapic_rte_info which they used before disabling.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
sys_fallocate for ia64. This uses an empty slot #1303 erroneously
marked as reserved for move_pages (which had already been allocated
as syscall #1276)
Signed-Off-By: Dave Chinner <dgc@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since Ingo's recent scheduler rewrite which was merged as commit
0437e109e1 sched_cacheflush is unused.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently most of the per cpu data, which is accessed by different cpus,
has a ____cacheline_aligned_in_smp attribute. Move all this data to the
new per cpu shared data section: .data.percpu.shared_aligned.
This will seperate the percpu data which is referenced frequently by other
cpus from the local only percpu data.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per cpu data section contains two types of data. One set which is
exclusively accessed by the local cpu and the other set which is per cpu,
but also shared by remote cpus. In the current kernel, these two sets are
not clearely separated out. This can potentially cause the same data
cacheline shared between the two sets of data, which will result in
unnecessary bouncing of the cacheline between cpus.
One way to fix the problem is to cacheline align the remotely accessed per
cpu data, both at the beginning and at the end. Because of the padding at
both ends, this will likely cause some memory wastage and also the
interface to achieve this is not clean.
This patch:
Moves the remotely accessed per cpu data (which is currently marked
as ____cacheline_aligned_in_smp) into a different section, where all the data
elements are cacheline aligned. And as such, this differentiates the local
only data and remotely accessed data cleanly.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I realise jprobes are a razor-blades-included type of interface, but that
doesn't mean we can't try and make them safer to use. This guy I know once
wrote code like this:
struct jprobe jp = { .kp.symbol_name = "foo", .entry = "jprobe_foo" };
And then his kernel exploded. Oops.
This patch adds an arch hook, arch_deref_entry_point() (I don't like it
either) which takes the void * in a struct jprobe, and gives back the text
address that it represents.
We can then use that in register_jprobe() to check that the entry point we're
passed is actually in the kernel text, rather than just some random value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Clean away some code inside some non-existent CONFIG ifdefs
[IA64] ar.itc access must really be after xtime_lock.sequence has been read
[IA64] correctly count CPU objects in the ia64/sn hwperf interface
[IA64] arbitary speed tty ioctl support
[IA64] use machvec=dig on hpzx1 platforms
