Do not explicity set the default input mode. Use the hardware default
of mode 0 ('Control vinyl'), which is now available.
This reverts commit e3ca4c9.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After removing code, only one case remains. So use an 'if' instead.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This feature was undocumented on early A4DJ units. It is indicated
by lighting both the 'line' and 'phono' lamps at the same time.
Newer units document this and the newer Windows drivers enable this
for all units, so restore the functionality.
This patch simplifies the code and changes the mode mapping to match
the A8DJ, favouring simpler code and consistency over keeping the
existing mapping.
Both 'Control vinyl' and 'Phono' input modes enable the hardware
preamp. The difference is the input impedance.
This reverts commit 9a9527e.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/551949
Symptom: On the reporter's Shuttle device, using PulseAudio in Ubuntu
10.04 LTS results in "popping clicking" audio with the PA crashing
shortly thereafter.
Test case: Using Ubuntu 10.04 LTS (Linux 2.6.32.12), Linux 2.6.33, or
Linux 2.6.34, adjust the HDA device's volume with PulseAudio.
Resolution: add SSID for this machine to the position_fix quirk table,
explicitly specifying the LPIB method.
Reported-and-Tested-By: Christian Mehlis <mehlis@inf.fu-berlin.de>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If an mds request is aborted (timeout, SIGKILL), it is left registered to
keep our state in sync with the mds. If we get a forward notification,
though, we know the request didn't succeed and we can unregister it
safely. We were trying to resend it, but then bailing out (and not
unregistering) in __do_request.
Signed-off-by: Sage Weil <sage@newdream.net>
The auth module (part of the mon_client) is needed to free any
ceph_authorizer(s) used by the mds and osd connections. Flush the msgr
workqueue before stopping monc to ensure that the destroy_authorizer
auth op is available when those connections are closed out.
Signed-off-by: Sage Weil <sage@newdream.net>
The lease code includes a mask in the CEPH_LOCK_* namespace, but that
namespace is changing, and only one mask (formerly _DN == 1) is used, so
hard code for that value for now.
If we ever extend this code to handle leases over different data types we
can extend it accordingly.
Signed-off-by: Sage Weil <sage@newdream.net>
Use ERR_CAST(x) rather than ERR_PTR(PTR_ERR(x)). The former makes more
clear what is the purpose of the operation, which otherwise looks like a
no-op.
In the case of fs/ceph/inode.c, ERR_CAST is not needed, because the type of
the returned value is the same as the type of the enclosing function.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T x;
identifier f;
@@
T f (...) { <+...
- ERR_PTR(PTR_ERR(x))
+ x
...+> }
@@
expression x;
@@
- ERR_PTR(PTR_ERR(x))
+ ERR_CAST(x)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Sage Weil <sage@newdream.net>
We were only requesting renewal after our tickets expire; do so before
that. Most of the low-level logic for this was already there; just use
it.
Signed-off-by: Sage Weil <sage@newdream.net>
We only want to send pending mon requests when we successfully
authenticate. If we are already authenticated, like when we renew our
ticket, there is no need to resend pending requests.
Signed-off-by: Sage Weil <sage@newdream.net>
fs/ceph/auth.c: linux/slab.h is included more than once.
fs/ceph/super.h: linux/slab.h is included more than once.
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Sage Weil <sage@newdream.net>
ac->ops may be null; use protocol id in error message instead.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The underlying problem is that many mds requests can't be restarted. For
example, a restarted create() would return -EEXIST if the original request
succeeds. However, we do not want a hung MDS to hang the client too. So,
use the _killable wait_for_completion variants to abort on SIGKILL but
nothing else.
Signed-off-by: Sage Weil <sage@newdream.net>
Add missing _killable_timeout variant for wait_for_completion that will
return when a timeout expires or the task is killed.
CC: Ingo Molnar <mingo@elte.hu>
CC: Andreas Herrmann <andreas.herrmann3@amd.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: native hardware cpuidle driver for latest Intel processors
ACPI: acpi_idle: touch TS_POLLING only in the non-MWAIT case
acpi_pad: uses MONITOR/MWAIT, so it doesn't need to clear TS_POLLING
sched: clarify commment for TS_POLLING
ACPI: allow a native cpuidle driver to displace ACPI
cpuidle: make cpuidle_curr_driver static
cpuidle: add cpuidle_unregister_driver() error check
cpuidle: fail to register if !CONFIG_CPU_IDLE
airlied -> brown paper bag.
I blame Hi-5 or the Wiggles for lowering my IQ, move the fix inside some
brackets instead of breaking everything in site.
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
acpi pad driver kind of aggressively marks TSC as unstable at init
time, on mwait capable and non X86_FEATURE_NONSTOP_TSC systems. This is
irrespective of whether pad driver is ever going to be used on the
system or deep C-states are supported/used. This will affect every user
who just happens to compile in (or get a kernel version which
compiles in) acpi pad driver.
Move mark_tsc_unstable() out of init to the actual idle invocation path
of the pad driver.
There is also another bug/missing_feature in the code that it does not
support 'always running apic timer' and switches to broadcast mode
unconditionally. Shaohua, can you take a look at that please.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sleep.h:3: WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_enter_[simple,bm] does
idle timing in ns, convert it to timeval, then to us, then to
pmtimer_ticks and then back to ns.
This patch changes things to
idle timing in ns, convert it to us, and then to pmtimer_ticks.
Just saves an imul along this path, but makes the code cleaner.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This EXPERIMENTAL driver supersedes acpi_idle on
Intel Atom Processors, Intel Core i3/i5/i7 Processors
and associated Intel Xeon processors.
It does not support the Intel Core2 processor or earlier.
For kernels configured with ACPI, CONFIG_INTEL_IDLE=y
allows intel_idle to probe before the ACPI processor driver.
Booting with "intel_idle.max_cstate=0" disables intel_idle
and the system will fall back on ACPI's "acpi_idle".
Typical Linux distributions load ACPI processor module early,
making CONFIG_INTEL_IDLE=m not easily useful on ACPI platforms.
intel_idle probes all processors at module_init time.
Processors that are hot-added later will be limited
to using C1 in idle.
Signed-off-by: Len Brown <len.brown@intel.com>
commit d306ebc286
(ACPI: Be in TS_POLLING state during mwait based C-state entry)
fixed an important power & performance issue where ACPI c2 and c3 C-states
were clearing TS_POLLING even when using MWAIT (ACPI_STATE_FFH).
That bug had been causing us to receive redundant scheduling interrups
when we had already been woken up by MONITOR/MWAIT.
Following up on that...
In the MWAIT case, we don't have to subsequently
check need_resched(), as that c heck was there
for the TS_POLLING-clearing case.
Note that not only does the cpuidle calling function
already check need_resched() before calling us, the
low-level entry into monitor/mwait calls it twice --
guaranteeing that a write to the trigger address
can not go un-noticed.
Also, in this case, we don't have to set TS_POLLING
when we wake, because we never cleared it.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Commit 38516ab59f ("tracing: Let
tracepoints have data passed to tracepoint callbacks") requires this
fixup to the powerpc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
netlink: bug fix: wrong size was calculated for vfinfo list blob
netlink: bug fix: don't overrun skbs on vf_port dump
xt_tee: use skb_dst_drop()
netdev/fec: fix ifconfig eth0 down hang issue
cnic: Fix context memory init. on 5709.
drivers/net: Eliminate a NULL pointer dereference
drivers/net/hamradio: Eliminate a NULL pointer dereference
be2net: Patch removes redundant while statement in loop.
ipv6: Add GSO support on forwarding path
net: fix __neigh_event_send()
vhost: fix the memory leak which will happen when memory_access_ok fails
vhost-net: fix to check the return value of copy_to/from_user() correctly
vhost: fix to check the return value of copy_to/from_user() correctly
vhost: Fix host panic if ioctl called with wrong index
net: fix lock_sock_bh/unlock_sock_bh
net/iucv: Add missing spin_unlock
net: ll_temac: fix checksum offload logic
net: ll_temac: fix interrupt bug when interrupt 0 is used
sctp: dubious bitfields in sctp_transport
ipmr: off by one in __ipmr_fill_mroute()
...
ARCH_KMALLOC_MINALIGN was already defined in asm/mem-layout.h and so shouldn't
have been added to asm/cache.h as well, but rather altered in place.
The commit that added it to asm/cache.h was:
commit 69dcf3db03
Author: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Date: Mon May 24 14:32:54 2010 -0700
frv: set ARCH_KMALLOC_MINALIGN
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is
DMA-safe: the buffer doesn't share a cache with the others.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
remove detritus left by "mm: make read_cache_page synchronous"
fix fs/sysv s_dirt handling
fat: convert to use the new truncate convention.
ext2: convert to use the new truncate convention.
tmpfs: convert to use the new truncate convention
fs: convert simple fs to new truncate
kill spurious reference to vmtruncate
fs: introduce new truncate sequence
fs/super: fix kernel-doc warning
fs/minix: bugfix, number of indirect block ptrs per block depends on block size
rename the generic fsync implementations
drop unused dentry argument to ->fsync
fs: Add missing mutex_unlock
Fix racy use of anon_inode_getfd() in perf_event.c
get rid of the magic around f_count in aio
VFS: fix recent breakage of FS_REVAL_DOT
Revert "anon_inode: set S_IFREG on the anon_inode"
gets minix get_dir_page() in sync with its analogs; back in 2007
Nick has switched read_cache_page() and friends to sync behaviour
(i.e. they wait for the page to get unlocked, check if it's uptodate
and if it isn't return ERR_PTR(-EIO) instead) and removed the
duplicate logics from the callers. In case of fs/minix/dir.c he'd
removed only half of that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Finding the list of Makefiles in streamline-config should not report errors.
Also move the "chomp" to the @makefiles array instead of doing it in the
for loop. This is more efficient, and does not make it any less readable
by C programmers.
Signed-off-by: Toralf Foerster <toralf.foerster@gmx.de>
LKML-Reference: <201005262022.02928.toralf.foerster@gmx.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Proper perl requires that local variables should be declared with 'my',
otherwise this may produce errors.
Signed-off-by: Toralf Foerster <toralf.foerster@gmx.de>
LKML-Reference: <201005281025.00358.toralf.foerster@gmx.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The wrong size was being calculated for vfinfo. In one case, it was over-
calculating using nlmsg_total_size on attrs, in another case, it was
under-calculating by assuming ifla_vf_* structs are packed together, but
each struct is it's own attr w/ hdr (and padding).
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Patrick McHardy: was continuing to fill skb after a
nla_put_failure, ignoring the size calculated by upper layer. Now,
return -EMSGSIZE on any overruns, but also allow netdev to
fail ndo_get_vf_port with error other than -EMSGSIZE, thus unwinding
nest.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 7fee226a (net: add a noref bit on skb dst), its wrong to
use : dst_release(skb_dst(skb)), since we could decrement a refcount
while skb dst was not refcounted.
We should use skb_dst_drop(skb) instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/559065
In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.
Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the structure to avoid the following warning:
WARNING: drivers/serial/built-in.o(.data+0x534): Section mismatch in reference from the variable s5p_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s5p_serial_drv references
the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the framebuffer driver and some basic LCD configurations
that should be suitable for the SMDK boards.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
