At the moment, if there is no CPU specified for a given
event, we use cpu_online_mask and try to build path for
each of the CPUs in the mask. This could prevent any CPU
that is turned online later to be used for the tracing.
This patch changes to use the cpu_present_mask and tries
to build path for as much CPUs as possible ignoring the
failures in building path for some of the CPUs. If ever
we try to trace on those CPUs, we fail the operation.
Based on a patch from Mathieu Poirier.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We create a coresight trace path for each online CPU when
we start the event. We rely on the number of online CPUs
and then go on to allocate an array matching the "number of
online CPUs" for holding the path and then uses normal
CPU id as the index to the array. This is problematic as
we could have some offline CPUs causing us to access beyond
the actual array size (e.g, on a dual SMP system, if CPU0 is
offline, CPU1 could be really accessing beyond the array).
The solution is to switch to per-cpu array for holding the path.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETB is already enabled in sysfs mode, the ETB reports
success even if a perf mode is requested. Fix this by checking
the requested mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight components could be operated either in sysfs mode or in perf
mode. For some of the components, the mode of operation doesn't matter as
they simply relay the data to the next component in the trace path. But for
sinks, they need to be able to provide the trace data back to the user.
Thus we need to make sure that "mode" is handled appropriately. e.g,
the sysfs mode could have multiple sources driving the trace data, while
perf mode doesn't allow sharing the sink.
The coresight_enable_sink() however doesn't really allow this check to
trigger as it skips the "enable_sink" callback if the component is
already enabled, irrespective of the mode. This could cause mixing
of data from different modes or even same mode (in perf), if the
sources are different. Also, if we fail to enable the sink while
enabling a path (where sink is the first component enabled),
we could end up in disabling the components in the "entire"
path which were not enabled in this trial, causing disruptions
in the existing trace paths.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ERR_CAT inlined function to replace the ERR_PTR(PTR_ERR). It
make the code more concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight drivers relied on default bindings for graph
in DT, while reusing the "reg" field of the "ports" to indicate
the actual hardware port number for the connections. This can
cause duplicate ports with same addresses, but different
direction. However, with the rules getting stricter for the
address mismatch with the label, it is no longer possible to use
the port address field for the hardware port number.
This patch introduces new DT binding rules for coresight
components, based on the same generic DT graph bindings, but
avoiding the address duplication.
- All output ports must be specified under a child node with
name "out-ports".
- All input ports must be specified under a childe node with
name "in-ports".
- Port address should match the hardware port number.
The support for legacy bindings is retained, with a warning.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform code parses the component connections and populates
a platform-description of the output connections in arrays of fields
(which is never freed). This is later copied in the coresight_register
to a newly allocated area, represented by coresight_connection(s).
This patch cleans up the code dealing with connections by making
use of the "coresight_connection" structure right at the platform
code and lets the generic driver simply re-use information provided
by the platform.
Thus making it reader friendly as well as avoiding the wastage of
unused memory.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to check if the given endpoint is input.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When parsing the remote endpoint of an output port, we do :
rport = of_graph_get_remote_port(ep);
rparent = of_graph_get_remote_port_parent(ep);
and then parse the "remote_port" as if it was the remote endpoint,
which is wrong. The code worked fine because we used endpoint number
as the port number. Let us fix it and optimise a bit as:
remote_ep = of_graph_get_remote_endpoint(ep);
if (remote_ep)
remote_parent = of_graph_get_port_parent(remote_ep);
and then, parse the remote_ep for the port/endpoint details.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't drop the reference on the remote device while parsing the
connection, held by bus_find_device(). Fix this by duplicating the
device name and dropping the reference.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight driver doesn't drop the references on the
remote endpoint/port nodes. Add the missing of_node_put()
calls.
Reported-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the of graph endpoint parsing code, to make the error
handling easier.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6403587a930c ("coresight: use put_device() instead of kfree()")
fixes the double freeing of resources and ensures that the device
refcount is dropped properly. Add a comment to explain this to
help the readers and prevent people trying to "unfix" it again.
While at it, rename the labels for better readability.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
See 1c8f422059 ("mm: change return type to vm_fault_t") for reference.
Link: http://lkml.kernel.org/r/20180702155801.GA4010@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probing the TPIU driver under UBSan triggers an out-of-bounds shift
warning in coresight_timeout():
...
[ 5.677530] UBSAN: Undefined behaviour in drivers/hwtracing/coresight/coresight.c:929:16
[ 5.685542] shift exponent 64 is too large for 64-bit type 'long unsigned int'
...
On closer inspection things are exponentially out of whack because we're
passing a bitmask where a bit number should be. Amusingly, it seems that
both calls will find their expected values by sheer luck and appear to
succeed: 1 << FFCR_FON_MAN ends up at bit 64 which whilst undefined
evaluates as zero in practice, while 1 << FFSR_FT_STOPPED finds bit 2
(TCPresent) which apparently is usually tied high.
Following the examples of other drivers, define separate FOO and FOO_BIT
macros for masks vs. indices, and put things right.
CC: Robert Walker <robert.walker@arm.com>
CC: Mike Leach <mike.leach@linaro.org>
CC: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 11595db8e1 ("coresight: Fix disabling of CoreSight TPIU")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can use a CATU with a scatter gather table, add support
for the TMC ETR to make use of the connected CATU in translate mode.
This is done by adding CATU as new buffer mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support for setting up a SG table for use
by the CATU. We reuse the tmc_sg_table to represent the table/data
pages, even though the table format is different.
Similar to ETR SG table, CATU uses a 4KB page size for data buffers
as well as page tables. All table entries are 64bit wide and have
the following format:
63 12 1 0
x-----------------------------------x
| Address [63-12] | SBZ | V |
x-----------------------------------x
Where [V] -> 0 - Pointer is invalid
1 - Pointer is Valid
CATU uses only first half of the page for data page pointers.
i.e, single table page will only have 256 page pointers, addressing
upto 1MB of data. The second half of a table page contains only two
pointers at the end of the page (i.e, pointers at index 510 and 511),
which are used as links to the "Previous" and "Next" page tables
respectively.
The first table page has an "Invalid" previous pointer and the
next pointer entry points to the second page table if there is one.
Similarly the last table page has an "Invalid" next pointer to
indicate the end of the table chain.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the initial support for Coresight Address Translation Unit, which
augments the TMC in Coresight SoC-600 by providing an improved Scatter
Gather mechanism. CATU is always connected to a single TMC-ETR and
converts the AXI address with a translated address (from a given SG
table with specific format). The CATU should be programmed in pass
through mode and enabled even if the ETR doesn't use the translation
by CATU.
This patch provides mechanism to enable/disable the CATU always in the
pass through mode.
We reuse the existing ports mechanism to link the TMC-ETR to the
connected CATU.
i.e, TMC-ETR:output_port0 -> CATU:input_port0
Reference manual for CATU component is avilable in version r2p0 of :
"Arm Coresight System-on-Chip SoC-600 Technical Reference Manual".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new coresight device type, which do not belong to any
of the existing types, i.e, source, sink, link etc. A helper
device could be connected to a coresight device, which could
augment the functionality of the coresight device.
This is intended to cover Coresight Address Translation Unit (CATU)
devices, which provide improved Scatter Gather mechanism for TMC
ETR. The idea is that the helper device could be controlled by
the driver of the device it is attached to (in this case ETR),
transparent to the generic coresight driver (and paths).
The operations include enable(), disable(), both of which could
accept a device specific "data" which the driving device and
the helper device could share. Since they don't appear in the
coresight "path" tracked by software, we have to ensure that
they are powered up/down whenever the master device is turned
on.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to find the input / output port for a LINK component
while enabling a path, we should fail gracefully rather than
assuming port "0".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We request for "CORESIGHT_BARRIER_PKT_SIZE" length and we should
be happy when we get that size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly introduced code fails to build in some configurations
unless we include the right headers:
drivers/hwtracing/coresight/coresight-tmc-etr.c: In function 'tmc_free_table_pages':
drivers/hwtracing/coresight/coresight-tmc-etr.c:206:3: error: implicit declaration of function 'vunmap'; did you mean 'iounmap'? [-Werror=implicit-function-declaration]
Fixes: 79613ae8715a ("coresight: Add generic TMC sg table framework")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can dynamically switch between contiguous memory and
SG table depending on the trace buffer size, provide the support
for selecting an appropriate buffer size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support for Scatter-Gather mode to the etr-buf layer.
Since we now have two different modes, we choose the backend
based on a set of conditions, documented in the code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC-ETR can use the target trace buffer in two different modes.
Normal physically contiguous mode and a discontiguous list pages in
Scatter-Gather mode. Also we have dedicated Coresight component, CATU
(Coresight Address Translation Unit) to provide improved scatter-gather
mode in Coresight SoC-600. This complicates the management of the
buffer used for trace, depending on the mode in which ETR is configured.
So, this patch adds a transparent layer for managing the ETR buffer
which abstracts the basic operations on the buffer (alloc, free,
sync and retrieve the data) and uses the mode specific helpers to
do the actual operation. This also allows the ETR driver to choose
the best mode for a given use case and adds the flexibility to
fallback to a different mode, without duplicating the code.
The patch also adds the "normal" flat memory mode and switches
the sysfs driver to use the new layer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for setting up an SG table used by the
TMC ETR inbuilt SG unit. The TMC ETR uses 4K page sized tables
to hold pointers to the 4K data pages with the last entry in a
table pointing to the next table with the entries, by kind of
chaining. The 2 LSBs determine the type of the table entry, to
one of :
Normal - Points to a 4KB data page.
Last - Points to a 4KB data page, but is the last entry in the
page table.
Link - Points to another 4KB table page with pointers to data.
The code takes care of handling the system page size which could
be different than 4K. So we could end up putting multiple ETR
SG tables in a single system page, vice versa for the data pages.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to add the support for ETR builtin scatter-gather mode
for dealing with large amount of trace buffers. However, on some of
the platforms, using the ETR SG mode can lock up the system due to
the way the ETR is connected to the memory subsystem.
In SG mode, the ETR performs READ from the scatter-gather table to
fetch the next page and regular WRITE of trace data. If the READ
operation doesn't complete(due to the memory subsystem issues,
which we have seen on a couple of platforms) the trace WRITE
cannot proceed leading to issues. So, we by default do not
use the SG mode, unless it is known to be safe on the platform.
We define a DT property for the TMC node to specify whether we
have a proper SG mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Horley <john.horley@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: devicetree@vger.kernel.org
Cc: frowand.list@gmail.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we open code filling the trace buffer with synchronization
packets when the circular buffer wraps around in different drivers.
Move this to a common place. While at it, clean up the barrier_pkt
array to strip off the trailing '\0'.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't support ETR in perf mode yet. So, don't
even try to enable the hardware, even by mistake.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We zero out the entire trace buffer used for ETR before it is enabled,
for helping with debugging. With the addition of scatter-gather mode,
the buffer could be bigger and non-contiguous.
Get rid of this step; if someone wants to debug, they can always add it
as and when needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ETM PIDs of the Arm cortex-A CPUs to the white list of ETMs.
While at it add a helper macro to make it easier to add the new
entries.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with ETM3x, the ETM4x tracers can trigger trace acquisition based on
contextID value, something that isn't useful when PID namespaces are
enabled. Indeed the PID value of a process has a different representation
in the kernel and the PID namespace, making the feature confusing and
potentially leaking internal kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tracers can trigger trace acquisition based on contextID value, something
that isn't useful when PID namespaces are enabled. Indeed the PID value
of a process has a different representation in the kernel and the PID
namespace, making the feature confusing and potentially leaking internal
kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbXfQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymwCACdFbUy2kWwrpZWSfSBpawfrs75lLMAmwVOe+62
9aDsDWzDVUEFxF20qiE6
=CMJ3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
vmw_balloon: fixing double free when batching mode is off
MAINTAINERS: Add driver-api/fpga path
fpga: clarify that unregister functions also free
documentation: fpga: move fpga-region.txt to driver-api
documentation: fpga: add bridge document to driver-api
documentation: fpga: move fpga-mgr.txt to driver-api
Documentation: fpga: move fpga overview to driver-api
fpga: region: kernel-doc fixes
fpga: bridge: kernel-doc fixes
fpga: mgr: kernel-doc fixes
fpga: use SPDX
fpga: region: change api, add fpga_region_create/free
fpga: bridge: change api, don't use drvdata
fpga: manager: change api, don't use drvdata
fpga: region: don't use drvdata in common fpga code
Drivers: hv: vmbus: Removed an unnecessary cast from void *
ver_linux: Drop redundant calls to system() to test if file is readable
ver_linux: Move stderr redirection from function parameter to function body
misc: IBM Virtual Management Channel Driver (VMC)
rpmsg: Correct support for MODULE_DEVICE_TABLE()
...
Commit b5e2ced9bf ("stm class: Use vmalloc for the master map") caused
a build error on some arches as vmalloc.h was not explicitly included.
Fix that by adding it to the list of includes.
Fixes: b5e2ced9bf ("stm class: Use vmalloc for the master map")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d5c435df4a ("intel_th: msu: Use the real device in case of IOMMU
domain allocation") changes dma buffer allocation to use the actual
underlying device, but forgets to change the deallocation path, which leads
to (if you've got CAP_SYS_RAWIO):
> # echo 0,0 > /sys/bus/intel_th/devices/0-msc0/nr_pages
> ------------[ cut here ]------------
> kernel BUG at ../linux/drivers/iommu/intel-iommu.c:3670!
> CPU: 3 PID: 231 Comm: sh Not tainted 4.17.0-rc1+ #2729
> RIP: 0010:intel_unmap+0x11e/0x130
...
> Call Trace:
> intel_free_coherent+0x3e/0x60
> msc_buffer_win_free+0x100/0x160 [intel_th_msu]
This patch fixes the buffer deallocation code to use the correct device.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: d5c435df4a ("intel_th: msu: Use the real device in case of IOMMU domain allocation")
Reported-by: Baofeng Tian <baofeng.tian@intel.com>
CC: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fengguang is running into a warning from the buddy allocator:
> swapper/0: page allocation failure: order:9, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
> CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.17.0-rc1 #262
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
> Call Trace:
...
> __kmalloc+0x14b/0x180: ____cache_alloc at mm/slab.c:3127
> stm_register_device+0xf3/0x5c0: stm_register_device at drivers/hwtracing/stm/core.c:695
...
Which is basically a result of the stm class trying to allocate ~512kB
for the dummy_stm with its default parameters. There's no reason, however,
for it not to be vmalloc()ed instead, which is what this patch does.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
CC: stable@vger.kernel.org # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.
As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.
So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker. As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either. Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
This is a cosmetic patch that deals with the address filter structure's
ambiguous fields 'filter' and 'range'. The former stands to mean that the
filter's *action* should be to filter the traces to its address range if
it's set or stop tracing if it's unset. This is confusing and hard on the
eyes, so this patch replaces it with 'action' enum. The 'range' field is
completely redundant (meaning that the filter is an address range as
opposed to a single address trigger), as we can use zero size to mean the
same thing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20180329120648.11902-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These are:
* Mass conversion to GPL-2 SPDX header
* Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
* Added MAINTAINERS entry for drivers/hwtracing
* Somewhat small Trace Hub fixes
* Added ACPI glue layer for the Trace Hub
* Added more module parameters to dummy_stm for better test coverage
-----BEGIN PGP SIGNATURE-----
iJkEABEIAEEWIQQSviFCoXpKPDNATbnrxfYkYwVX/wUCWrzG7yMcYWxleGFuZGVy
LnNoaXNoa2luQGxpbnV4LmludGVsLmNvbQAKCRDrxfYkYwVX/0jcAQCE/maw6L5P
NdT3Ck3EuDWzij9uimq3Y0UyI9F4Cd+vYgD+N8Skyiua+NqfBGB0oXNsJt2acirg
O3G990RK9dX4H2c=
=CuGw
-----END PGP SIGNATURE-----
Merge tag 'stm-intel_th-for-greg-20180329' of git://git.kernel.org/pub/scm/linux/kernel/git/ash/stm into char-misc-next
Alexander writes:
stm class/intel_th: Updates for 4.17
These are:
* Mass conversion to GPL-2 SPDX header
* Moved "hwtracing" to now its own submenu, to uncrowd the parent menu a bit
* Added MAINTAINERS entry for drivers/hwtracing
* Somewhat small Trace Hub fixes
* Added ACPI glue layer for the Trace Hub
* Added more module parameters to dummy_stm for better test coverage
