kernel_optimize_test/drivers/bcma
Arnd Bergmann defb893fff bcma: use of_dma_configure() to set initial dma mask
While fixing another bug, I noticed that bcma manually sets up
a dma_mask pointer for its child devices. We have a generic
helper for that now, which should be able to cope better with
any variations that might be needed to deal with cache coherency,
unusual DMA address offsets, iommus, or limited DMA masks, none
of which are currently handled here.

This changes the core to use the of_dma_configure(), like
we do for platform devices that are probed directly from
DT.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-09-09 12:00:37 +03:00
..
bcma_private.h x86/quirks: Add early quirk to reset Apple AirPort card 2016-07-10 20:13:53 +02:00
core.c
driver_chipcommon_b.c bcma: define ChipCommon B MII registers 2016-07-19 21:13:10 +03:00
driver_chipcommon_nflash.c
driver_chipcommon_pflash.c bcma: move parallel flash support to separated file 2016-03-07 14:41:08 +02:00
driver_chipcommon_pmu.c bcma: support PMU present as separated bus core 2016-02-06 13:36:11 +02:00
driver_chipcommon_sflash.c mtd: bcm47xxsflash: use ioremap_cache() instead of KSEG0ADDR() 2016-04-04 00:07:57 -07:00
driver_chipcommon.c bcma: support BCM53573 series of wireless SoCs 2016-09-03 12:58:42 +03:00
driver_gmac_cmn.c
driver_gpio.c Major changes: 2016-02-16 20:38:29 -05:00
driver_mips.c bcma: move flash detection code to ChipCommon core driver 2016-03-07 14:41:08 +02:00
driver_pci_host.c
driver_pci.c
driver_pcie2.c
host_pci.c bcma: add PCI ID for Foxconn's BCM43142 device 2016-07-18 22:38:24 +03:00
host_soc.c
Kconfig bcma: allow enabling serial flash support on non-MIPS SoCs 2016-07-18 22:43:35 +03:00
main.c bcma: use of_dma_configure() to set initial dma mask 2016-09-09 12:00:37 +03:00
Makefile bcma: move parallel flash support to separated file 2016-03-07 14:41:08 +02:00
README
scan.c bcma: support chipsets with PMU and GCI cores (devices) 2016-02-06 13:34:51 +02:00
scan.h
sprom.c
TODO

Broadcom introduced new bus as replacement for older SSB. It is based on AMBA,
however from programming point of view there is nothing AMBA specific we use.

Standard AMBA drivers are platform specific, have hardcoded addresses and use
AMBA standard fields like CID and PID.

In case of Broadcom's cards every device consists of:
1) Broadcom specific AMBA device. It is put on AMBA bus, but can not be treated
   as standard AMBA device. Reading it's CID or PID can cause machine lockup.
2) AMBA standard devices called ports or wrappers. They have CIDs (AMBA_CID)
   and PIDs (0x103BB369), but we do not use that info for anything. One of that
   devices is used for managing Broadcom specific core.

Addresses of AMBA devices are not hardcoded in driver and have to be read from
EPROM.

In this situation we decided to introduce separated bus. It can contain up to
16 devices identified by Broadcom specific fields: manufacturer, id, revision
and class.