forked from luck/tmp_suning_uos_patched
4f73bc4dd3
The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
42 lines
1.1 KiB
Plaintext
42 lines
1.1 KiB
Plaintext
#
|
|
# PPS clients configuration
|
|
#
|
|
|
|
if PPS
|
|
|
|
comment "PPS clients support"
|
|
|
|
config PPS_CLIENT_KTIMER
|
|
tristate "Kernel timer client (Testing client, use for debug)"
|
|
help
|
|
If you say yes here you get support for a PPS debugging client
|
|
which uses a kernel timer to generate the PPS signal.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called pps-ktimer.
|
|
|
|
config PPS_CLIENT_LDISC
|
|
tristate "PPS line discipline"
|
|
depends on PPS && TTY
|
|
help
|
|
If you say yes here you get support for a PPS source connected
|
|
with the CD (Carrier Detect) pin of your serial port.
|
|
|
|
config PPS_CLIENT_PARPORT
|
|
tristate "Parallel port PPS client"
|
|
depends on PPS && PARPORT
|
|
help
|
|
If you say yes here you get support for a PPS source connected
|
|
with the interrupt pin of your parallel port.
|
|
|
|
config PPS_CLIENT_GPIO
|
|
tristate "PPS client using GPIO"
|
|
depends on PPS && GENERIC_HARDIRQS
|
|
help
|
|
If you say yes here you get support for a PPS source using
|
|
GPIO. To be useful you must also register a platform device
|
|
specifying the GPIO pin and other options, usually in your board
|
|
setup.
|
|
|
|
endif
|