forked from luck/tmp_suning_uos_patched
8d2f1a9d36
Add the regulator subnodes to the Qualcomm RPM MFD device tree bindings. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
265 lines
7.0 KiB
Plaintext
265 lines
7.0 KiB
Plaintext
Qualcomm Resource Power Manager (RPM)
|
|
|
|
This driver is used to interface with the Resource Power Manager (RPM) found in
|
|
various Qualcomm platforms. The RPM allows each component in the system to vote
|
|
for state of the system resources, such as clocks, regulators and bus
|
|
frequencies.
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: must be one of:
|
|
"qcom,rpm-apq8064"
|
|
"qcom,rpm-msm8660"
|
|
"qcom,rpm-msm8960"
|
|
"qcom,rpm-ipq8064"
|
|
|
|
- reg:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: base address and size of the RPM's message ram
|
|
|
|
- interrupts:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: three entries specifying the RPM's:
|
|
1. acknowledgement interrupt
|
|
2. error interrupt
|
|
3. wakeup interrupt
|
|
|
|
- interrupt-names:
|
|
Usage: required
|
|
Value type: <string-array>
|
|
Definition: must be the three strings "ack", "err" and "wakeup", in order
|
|
|
|
- qcom,ipc:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
|
|
Definition: three entries specifying the outgoing ipc bit used for
|
|
signaling the RPM:
|
|
- phandle to a syscon node representing the apcs registers
|
|
- u32 representing offset to the register within the syscon
|
|
- u32 representing the ipc bit within the register
|
|
|
|
|
|
= SUBNODES
|
|
|
|
The RPM exposes resources to its subnodes. The below bindings specify the set
|
|
of valid subnodes that can operate on these resources.
|
|
|
|
== Regulators
|
|
|
|
Regulator nodes are identified by their compatible:
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: must be one of:
|
|
"qcom,rpm-pm8058-regulators"
|
|
"qcom,rpm-pm8901-regulators"
|
|
"qcom,rpm-pm8921-regulators"
|
|
|
|
- vdd_l0_l1_lvs-supply:
|
|
- vdd_l2_l11_l12-supply:
|
|
- vdd_l3_l4_l5-supply:
|
|
- vdd_l6_l7-supply:
|
|
- vdd_l8-supply:
|
|
- vdd_l9-supply:
|
|
- vdd_l10-supply:
|
|
- vdd_l13_l16-supply:
|
|
- vdd_l14_l15-supply:
|
|
- vdd_l17_l18-supply:
|
|
- vdd_l19_l20-supply:
|
|
- vdd_l21-supply:
|
|
- vdd_l22-supply:
|
|
- vdd_l23_l24_l25-supply:
|
|
- vdd_ncp-supply:
|
|
- vdd_s0-supply:
|
|
- vdd_s1-supply:
|
|
- vdd_s2-supply:
|
|
- vdd_s3-supply:
|
|
- vdd_s4-supply:
|
|
Usage: optional (pm8058 only)
|
|
Value type: <phandle>
|
|
Definition: reference to regulator supplying the input pin, as
|
|
described in the data sheet
|
|
|
|
- lvs0_in-supply:
|
|
- lvs1_in-supply:
|
|
- lvs2_in-supply:
|
|
- lvs3_in-supply:
|
|
- mvs_in-supply:
|
|
- vdd_l0-supply:
|
|
- vdd_l1-supply:
|
|
- vdd_l2-supply:
|
|
- vdd_l3-supply:
|
|
- vdd_l4-supply:
|
|
- vdd_l5-supply:
|
|
- vdd_l6-supply:
|
|
- vdd_s0-supply:
|
|
- vdd_s1-supply:
|
|
- vdd_s2-supply:
|
|
- vdd_s3-supply:
|
|
- vdd_s4-supply:
|
|
Usage: optional (pm8901 only)
|
|
Value type: <phandle>
|
|
Definition: reference to regulator supplying the input pin, as
|
|
described in the data sheet
|
|
|
|
- vdd_l1_l2_l12_l18-supply:
|
|
- vdd_l3_l15_l17-supply:
|
|
- vdd_l4_l14-supply:
|
|
- vdd_l5_l8_l16-supply:
|
|
- vdd_l6_l7-supply:
|
|
- vdd_l9_l11-supply:
|
|
- vdd_l10_l22-supply:
|
|
- vdd_l21_l23_l29-supply:
|
|
- vdd_l24-supply:
|
|
- vdd_l25-supply:
|
|
- vdd_l26-supply:
|
|
- vdd_l27-supply:
|
|
- vdd_l28-supply:
|
|
- vdd_ncp-supply:
|
|
- vdd_s1-supply:
|
|
- vdd_s2-supply:
|
|
- vdd_s4-supply:
|
|
- vdd_s5-supply:
|
|
- vdd_s6-supply:
|
|
- vdd_s7-supply:
|
|
- vdd_s8-supply:
|
|
- vin_5vs-supply:
|
|
- vin_lvs1_3_6-supply:
|
|
- vin_lvs2-supply:
|
|
- vin_lvs4_5_7-supply:
|
|
Usage: optional (pm8921 only)
|
|
Value type: <phandle>
|
|
Definition: reference to regulator supplying the input pin, as
|
|
described in the data sheet
|
|
|
|
The regulator node houses sub-nodes for each regulator within the device. Each
|
|
sub-node is identified using the node's name, with valid values listed for each
|
|
of the pmics below.
|
|
|
|
pm8058:
|
|
l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
|
|
l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
|
|
lvs0, lvs1, ncp
|
|
|
|
pm8901:
|
|
l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
|
|
mvs
|
|
|
|
pm8921:
|
|
s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
|
|
l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
|
|
l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
|
|
ncp
|
|
|
|
The content of each sub-node is defined by the standard binding for regulators -
|
|
see regulator.txt - with additional custom properties described below:
|
|
|
|
=== Switch-mode Power Supply regulator custom properties
|
|
|
|
- bias-pull-down:
|
|
Usage: optional
|
|
Value type: <empty>
|
|
Definition: enable pull down of the regulator when inactive
|
|
|
|
- qcom,switch-mode-frequency:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: Frequency (Hz) of the switch-mode power supply;
|
|
must be one of:
|
|
19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
|
|
2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
|
|
1480000, 1370000, 1280000, 1200000
|
|
|
|
- qcom,force-mode:
|
|
Usage: optional (default if no other qcom,force-mode is specified)
|
|
Value type: <u32>
|
|
Defintion: indicates that the regulator should be forced to a
|
|
particular mode, valid values are:
|
|
QCOM_RPM_FORCE_MODE_NONE - do not force any mode
|
|
QCOM_RPM_FORCE_MODE_LPM - force into low power mode
|
|
QCOM_RPM_FORCE_MODE_HPM - force into high power mode
|
|
QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
|
|
select its own mode based on
|
|
realtime current draw, only for:
|
|
pm8921 smps and ftsmps
|
|
|
|
- qcom,power-mode-hysteretic:
|
|
Usage: optional
|
|
Value type: <empty>
|
|
Definition: select that the power supply should operate in hysteretic
|
|
mode, instead of the default pwm mode
|
|
|
|
=== Low-dropout regulator custom properties
|
|
|
|
- bias-pull-down:
|
|
Usage: optional
|
|
Value type: <empty>
|
|
Definition: enable pull down of the regulator when inactive
|
|
|
|
- qcom,force-mode:
|
|
Usage: optional
|
|
Value type: <u32>
|
|
Defintion: indicates that the regulator should not be forced to any
|
|
particular mode, valid values are:
|
|
QCOM_RPM_FORCE_MODE_NONE - do not force any mode
|
|
QCOM_RPM_FORCE_MODE_LPM - force into low power mode
|
|
QCOM_RPM_FORCE_MODE_HPM - force into high power mode
|
|
QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
|
|
mode, i.e. to act as a switch
|
|
and not regulate, only for:
|
|
pm8921 pldo, nldo and nldo1200
|
|
|
|
=== Negative Charge Pump custom properties
|
|
|
|
- qcom,switch-mode-frequency:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: Frequency (Hz) of the swith mode power supply;
|
|
must be one of:
|
|
19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
|
|
2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
|
|
1480000, 1370000, 1280000, 1200000
|
|
|
|
= EXAMPLE
|
|
|
|
#include <dt-bindings/mfd/qcom-rpm.h>
|
|
|
|
rpm@108000 {
|
|
compatible = "qcom,rpm-msm8960";
|
|
reg = <0x108000 0x1000>;
|
|
qcom,ipc = <&apcs 0x8 2>;
|
|
|
|
interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
|
|
interrupt-names = "ack", "err", "wakeup";
|
|
|
|
regulators {
|
|
compatible = "qcom,rpm-pm8921-regulators";
|
|
vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
|
|
|
|
s1 {
|
|
regulator-min-microvolt = <1225000>;
|
|
regulator-max-microvolt = <1225000>;
|
|
|
|
bias-pull-down;
|
|
|
|
qcom,switch-mode-frequency = <3200000>;
|
|
};
|
|
|
|
pm8921_s4: s4 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
qcom,switch-mode-frequency = <1600000>;
|
|
bias-pull-down;
|
|
|
|
qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
|
|
};
|
|
};
|
|
};
|
|
|