forked from luck/tmp_suning_uos_patched
549e8152de
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as a position-independent executable (PIE) when it is set. This involves processing the dynamic relocations in the image in the early stages of booting, even if the kernel is being run at the address it is linked at, since the linker does not necessarily fill in words in the image for which there are dynamic relocations. (In fact the linker does fill in such words for 64-bit executables, though not for 32-bit executables, so in principle we could avoid calling relocate() entirely when we're running a 64-bit kernel at the linked address.) The dynamic relocations are processed by a new function relocate(addr), where the addr parameter is the virtual address where the image will be run. In fact we call it twice; once before calling prom_init, and again when starting the main kernel. This means that reloc_offset() returns 0 in prom_init (since it has been relocated to the address it is running at), which necessitated a few adjustments. This also changes __va and __pa to use an equivalent definition that is simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are constants (for 64-bit) whereas PHYSICAL_START is a variable (and KERNELBASE ideally should be too, but isn't yet). With this, relocatable kernels still copy themselves down to physical address 0 and run there. Signed-off-by: Paul Mackerras <paulus@samba.org>
413 lines
16 KiB
Makefile
413 lines
16 KiB
Makefile
# Makefile for making ELF bootable images for booting on CHRP
|
|
# using Open Firmware.
|
|
#
|
|
# Geert Uytterhoeven September 1997
|
|
#
|
|
# Based on coffboot by Paul Mackerras
|
|
# Simplified for ppc64 by Todd Inglett
|
|
#
|
|
# NOTE: this code is built for 32 bit in ELF32 format even though
|
|
# it packages a 64 bit kernel. We do this to simplify the
|
|
# bootloader and increase compatibility with OpenFirmware.
|
|
#
|
|
# To this end we need to define BOOTCC, etc, as the tools
|
|
# needed to build the 32 bit image. That's normally the same
|
|
# compiler for the rest of the kernel, with the -m32 flag added.
|
|
# To make it easier to setup a cross compiler,
|
|
# CROSS32_COMPILE is setup as a prefix just like CROSS_COMPILE
|
|
# in the toplevel makefile.
|
|
|
|
all: $(obj)/zImage
|
|
|
|
BOOTCFLAGS := -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs \
|
|
-fno-strict-aliasing -Os -msoft-float -pipe \
|
|
-fomit-frame-pointer -fno-builtin -fPIC -nostdinc \
|
|
-isystem $(shell $(CROSS32CC) -print-file-name=include)
|
|
BOOTAFLAGS := -D__ASSEMBLY__ $(BOOTCFLAGS) -traditional -nostdinc
|
|
|
|
ifdef CONFIG_DEBUG_INFO
|
|
BOOTCFLAGS += -g
|
|
endif
|
|
|
|
ifeq ($(call cc-option-yn, -fstack-protector),y)
|
|
BOOTCFLAGS += -fno-stack-protector
|
|
endif
|
|
|
|
BOOTCFLAGS += -I$(obj) -I$(srctree)/$(obj) -I$(srctree)/$(src)/libfdt
|
|
|
|
DTS_FLAGS ?= -p 1024
|
|
|
|
$(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
|
|
$(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405
|
|
|
|
|
|
zlib := inffast.c inflate.c inftrees.c
|
|
zlibheader := inffast.h inffixed.h inflate.h inftrees.h infutil.h
|
|
zliblinuxheader := zlib.h zconf.h zutil.h
|
|
|
|
$(addprefix $(obj)/,$(zlib) cuboot-c2k.o gunzip_util.o main.o prpmc2800.o): \
|
|
$(addprefix $(obj)/,$(zliblinuxheader)) $(addprefix $(obj)/,$(zlibheader))
|
|
|
|
src-libfdt := fdt.c fdt_ro.c fdt_wip.c fdt_sw.c fdt_rw.c fdt_strerror.c
|
|
src-wlib := string.S crt0.S crtsavres.S stdio.c main.c \
|
|
$(addprefix libfdt/,$(src-libfdt)) libfdt-wrapper.c \
|
|
ns16550.c serial.c simple_alloc.c div64.S util.S \
|
|
gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \
|
|
4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
|
|
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
|
|
fsl-soc.c mpc8xx.c pq2.c
|
|
src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c \
|
|
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
|
|
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
|
|
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c \
|
|
cuboot-bamboo.c cuboot-mpc7448hpc2.c cuboot-taishan.c \
|
|
fixed-head.S ep88xc.c ep405.c cuboot-c2k.c \
|
|
cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c \
|
|
cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
|
|
virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c
|
|
src-boot := $(src-wlib) $(src-plat) empty.c
|
|
|
|
src-boot := $(addprefix $(obj)/, $(src-boot))
|
|
obj-boot := $(addsuffix .o, $(basename $(src-boot)))
|
|
obj-wlib := $(addsuffix .o, $(basename $(addprefix $(obj)/, $(src-wlib))))
|
|
obj-plat := $(addsuffix .o, $(basename $(addprefix $(obj)/, $(src-plat))))
|
|
|
|
quiet_cmd_copy_zlib = COPY $@
|
|
cmd_copy_zlib = sed "s@__used@@;s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
|
|
quiet_cmd_copy_zlibheader = COPY $@
|
|
cmd_copy_zlibheader = sed "s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
# stddef.h for NULL
|
|
quiet_cmd_copy_zliblinuxheader = COPY $@
|
|
cmd_copy_zliblinuxheader = sed "s@<linux/string.h>@\"string.h\"@;s@<linux/kernel.h>@<stddef.h>@;s@<linux/\([^>]*\).*@\"\1\"@" $< > $@
|
|
|
|
$(addprefix $(obj)/,$(zlib)): $(obj)/%: $(srctree)/lib/zlib_inflate/%
|
|
$(call cmd,copy_zlib)
|
|
|
|
$(addprefix $(obj)/,$(zlibheader)): $(obj)/%: $(srctree)/lib/zlib_inflate/%
|
|
$(call cmd,copy_zlibheader)
|
|
|
|
$(addprefix $(obj)/,$(zliblinuxheader)): $(obj)/%: $(srctree)/include/linux/%
|
|
$(call cmd,copy_zliblinuxheader)
|
|
|
|
$(obj)/empty.c:
|
|
@touch $@
|
|
|
|
$(obj)/zImage.lds $(obj)/zImage.coff.lds $(obj)/zImage.ps3.lds: $(obj)/%: $(srctree)/$(src)/%.S
|
|
@cp $< $@
|
|
|
|
clean-files := $(zlib) $(zlibheader) $(zliblinuxheader) \
|
|
empty.c zImage.coff.lds zImage.ps3.lds zImage.lds
|
|
|
|
quiet_cmd_bootcc = BOOTCC $@
|
|
cmd_bootcc = $(CROSS32CC) -Wp,-MD,$(depfile) $(BOOTCFLAGS) -c -o $@ $<
|
|
|
|
quiet_cmd_bootas = BOOTAS $@
|
|
cmd_bootas = $(CROSS32CC) -Wp,-MD,$(depfile) $(BOOTAFLAGS) -c -o $@ $<
|
|
|
|
quiet_cmd_bootar = BOOTAR $@
|
|
cmd_bootar = $(CROSS32AR) -cr $@.$$$$ $(filter-out FORCE,$^); mv $@.$$$$ $@
|
|
|
|
$(patsubst %.c,%.o, $(filter %.c, $(src-boot))): %.o: %.c FORCE
|
|
$(Q)mkdir -p $(dir $@)
|
|
$(call if_changed_dep,bootcc)
|
|
$(patsubst %.S,%.o, $(filter %.S, $(src-boot))): %.o: %.S FORCE
|
|
$(Q)mkdir -p $(dir $@)
|
|
$(call if_changed_dep,bootas)
|
|
|
|
$(obj)/wrapper.a: $(obj-wlib) FORCE
|
|
$(call if_changed,bootar)
|
|
|
|
hostprogs-y := addnote addRamDisk hack-coff mktree dtc
|
|
|
|
targets += $(patsubst $(obj)/%,%,$(obj-boot) wrapper.a)
|
|
extra-y := $(obj)/wrapper.a $(obj-plat) $(obj)/empty.o \
|
|
$(obj)/zImage.lds $(obj)/zImage.coff.lds $(obj)/zImage.ps3.lds
|
|
|
|
dtstree := $(srctree)/$(src)/dts
|
|
|
|
wrapper :=$(srctree)/$(src)/wrapper
|
|
wrapperbits := $(extra-y) $(addprefix $(obj)/,addnote hack-coff mktree dtc) \
|
|
$(wrapper) FORCE
|
|
|
|
#############
|
|
# Bits for building dtc
|
|
# DTC_GENPARSER := 1 # Uncomment to rebuild flex/bison output
|
|
|
|
dtc-objs := dtc.o flattree.o fstree.o data.o livetree.o treesource.o srcpos.o checks.o
|
|
dtc-objs += dtc-lexer.lex.o dtc-parser.tab.o
|
|
dtc-objs := $(addprefix dtc-src/, $(dtc-objs))
|
|
|
|
# prerequisites on generated files needs to be explicit
|
|
$(obj)/dtc-src/dtc-parser.tab.o: $(obj)/dtc-src/dtc-parser.tab.c $(obj)/dtc-src/dtc-parser.tab.h
|
|
$(obj)/dtc-src/dtc-lexer.lex.o: $(obj)/dtc-src/dtc-lexer.lex.c $(obj)/dtc-src/dtc-parser.tab.h
|
|
|
|
HOSTCFLAGS += -I$(src)/dtc-src/ -I$(src)/libfdt/
|
|
|
|
targets += dtc-src/dtc-parser.tab.c
|
|
targets += dtc-src/dtc-lexer.lex.c
|
|
|
|
clean-files += dtc-src/dtc-parser.tab.h
|
|
|
|
ifdef DTC_GENPARSER
|
|
BISON = bison
|
|
FLEX = flex
|
|
|
|
quiet_cmd_bison = BISON $@
|
|
cmd_bison = $(BISON) -o$@ -d $<; cp $@ $@_shipped
|
|
quiet_cmd_flex = FLEX $@
|
|
cmd_flex = $(FLEX) -o$@ $<; cp $@ $@_shipped
|
|
|
|
$(obj)/dtc-src/dtc-parser.tab.c: $(src)/dtc-src/dtc-parser.y FORCE
|
|
$(call if_changed,bison)
|
|
|
|
$(obj)/dtc-src/dtc-parser.tab.h: $(obj)/dtc-src/dtc-parser.tab.c
|
|
|
|
$(obj)/dtc-src/dtc-lexer.lex.c: $(src)/dtc-src/dtc-lexer.l FORCE
|
|
$(call if_changed,flex)
|
|
endif
|
|
|
|
#############
|
|
# Bits for building various flavours of zImage
|
|
|
|
ifneq ($(CROSS32_COMPILE),)
|
|
CROSSWRAP := -C "$(CROSS32_COMPILE)"
|
|
else
|
|
ifneq ($(CROSS_COMPILE),)
|
|
CROSSWRAP := -C "$(CROSS_COMPILE)"
|
|
endif
|
|
endif
|
|
|
|
# args (to if_changed): 1 = (this rule), 2 = platform, 3 = dts 4=dtb 5=initrd
|
|
quiet_cmd_wrap = WRAP $@
|
|
cmd_wrap =$(CONFIG_SHELL) $(wrapper) -c -o $@ -p $2 $(CROSSWRAP) \
|
|
$(if $3, -s $3)$(if $4, -d $4)$(if $5, -i $5) vmlinux
|
|
|
|
image-$(CONFIG_PPC_PSERIES) += zImage.pseries
|
|
image-$(CONFIG_PPC_MAPLE) += zImage.pseries
|
|
image-$(CONFIG_PPC_IBM_CELL_BLADE) += zImage.pseries
|
|
image-$(CONFIG_PPC_PS3) += dtbImage.ps3
|
|
image-$(CONFIG_PPC_CELLEB) += zImage.pseries
|
|
image-$(CONFIG_PPC_CHRP) += zImage.chrp
|
|
image-$(CONFIG_PPC_EFIKA) += zImage.chrp
|
|
image-$(CONFIG_PPC_PMAC) += zImage.pmac
|
|
image-$(CONFIG_PPC_HOLLY) += zImage.holly
|
|
image-$(CONFIG_PPC_PRPMC2800) += dtbImage.prpmc2800
|
|
image-$(CONFIG_PPC_ISERIES) += zImage.iseries
|
|
image-$(CONFIG_DEFAULT_UIMAGE) += uImage
|
|
|
|
#
|
|
# Targets which embed a device tree blob
|
|
#
|
|
# Theses are default targets to build images which embed device tree blobs.
|
|
# They are only required on boards which do not have FDT support in firmware.
|
|
# Boards with newish u-boot firmare can use the uImage target above
|
|
#
|
|
|
|
# Board ports in arch/powerpc/platform/40x/Kconfig
|
|
image-$(CONFIG_EP405) += dtbImage.ep405
|
|
image-$(CONFIG_WALNUT) += treeImage.walnut
|
|
|
|
# Board ports in arch/powerpc/platform/44x/Kconfig
|
|
image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony
|
|
image-$(CONFIG_BAMBOO) += treeImage.bamboo cuImage.bamboo
|
|
image-$(CONFIG_SAM440EP) += cuImage.sam440ep
|
|
image-$(CONFIG_SEQUOIA) += cuImage.sequoia
|
|
image-$(CONFIG_RAINIER) += cuImage.rainier
|
|
image-$(CONFIG_TAISHAN) += cuImage.taishan
|
|
image-$(CONFIG_KATMAI) += cuImage.katmai
|
|
image-$(CONFIG_WARP) += cuImage.warp
|
|
image-$(CONFIG_YOSEMITE) += cuImage.yosemite
|
|
|
|
# Board ports in arch/powerpc/platform/8xx/Kconfig
|
|
image-$(CONFIG_MPC86XADS) += cuImage.mpc866ads
|
|
image-$(CONFIG_MPC885ADS) += cuImage.mpc885ads
|
|
image-$(CONFIG_PPC_EP88XC) += dtbImage.ep88xc
|
|
image-$(CONFIG_PPC_ADDER875) += cuImage.adder875-uboot \
|
|
dtbImage.adder875-redboot
|
|
|
|
# Board ports in arch/powerpc/platform/52xx/Kconfig
|
|
image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 cuImage.lite5200b
|
|
|
|
# Board ports in arch/powerpc/platform/82xx/Kconfig
|
|
image-$(CONFIG_MPC8272_ADS) += cuImage.mpc8272ads
|
|
image-$(CONFIG_PQ2FADS) += cuImage.pq2fads
|
|
image-$(CONFIG_EP8248E) += dtbImage.ep8248e
|
|
|
|
# Board ports in arch/powerpc/platform/83xx/Kconfig
|
|
image-$(CONFIG_MPC832x_MDS) += cuImage.mpc832x_mds
|
|
image-$(CONFIG_MPC832x_RDB) += cuImage.mpc832x_rdb
|
|
image-$(CONFIG_MPC834x_ITX) += cuImage.mpc8349emitx \
|
|
cuImage.mpc8349emitxgp
|
|
image-$(CONFIG_MPC834x_MDS) += cuImage.mpc834x_mds
|
|
image-$(CONFIG_MPC836x_MDS) += cuImage.mpc836x_mds
|
|
image-$(CONFIG_ASP834x) += dtbImage.asp834x-redboot
|
|
|
|
# Board ports in arch/powerpc/platform/85xx/Kconfig
|
|
image-$(CONFIG_MPC8540_ADS) += cuImage.mpc8540ads
|
|
image-$(CONFIG_MPC8560_ADS) += cuImage.mpc8560ads
|
|
image-$(CONFIG_MPC85xx_CDS) += cuImage.mpc8541cds \
|
|
cuImage.mpc8548cds \
|
|
cuImage.mpc8555cds
|
|
image-$(CONFIG_MPC85xx_MDS) += cuImage.mpc8568mds
|
|
image-$(CONFIG_MPC85xx_DS) += cuImage.mpc8544ds \
|
|
cuImage.mpc8572ds
|
|
image-$(CONFIG_TQM8540) += cuImage.tqm8540
|
|
image-$(CONFIG_TQM8541) += cuImage.tqm8541
|
|
image-$(CONFIG_TQM8548) += cuImage.tqm8548
|
|
image-$(CONFIG_TQM8555) += cuImage.tqm8555
|
|
image-$(CONFIG_TQM8560) += cuImage.tqm8560
|
|
image-$(CONFIG_SBC8548) += cuImage.sbc8548
|
|
image-$(CONFIG_SBC8560) += cuImage.sbc8560
|
|
image-$(CONFIG_KSI8560) += cuImage.ksi8560
|
|
|
|
# Board ports in arch/powerpc/platform/embedded6xx/Kconfig
|
|
image-$(CONFIG_STORCENTER) += cuImage.storcenter
|
|
image-$(CONFIG_MPC7448HPC2) += cuImage.mpc7448hpc2
|
|
image-$(CONFIG_PPC_C2K) += cuImage.c2k
|
|
|
|
# For 32-bit powermacs, build the COFF and miboot images
|
|
# as well as the ELF images.
|
|
ifeq ($(CONFIG_PPC32),y)
|
|
image-$(CONFIG_PPC_PMAC) += zImage.coff zImage.miboot
|
|
endif
|
|
|
|
# Allow extra targets to be added to the defconfig
|
|
image-y += $(subst ",,$(CONFIG_EXTRA_TARGETS))
|
|
|
|
initrd- := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
|
|
initrd-y := $(patsubst zImage%, zImage.initrd%, \
|
|
$(patsubst dtbImage%, dtbImage.initrd%, \
|
|
$(patsubst simpleImage%, simpleImage.initrd%, \
|
|
$(patsubst treeImage%, treeImage.initrd%, $(image-y)))))
|
|
initrd-y := $(filter-out $(image-y), $(initrd-y))
|
|
targets += $(image-y) $(initrd-y)
|
|
|
|
$(addprefix $(obj)/, $(initrd-y)): $(obj)/ramdisk.image.gz
|
|
|
|
# Don't put the ramdisk on the pattern rule; when its missing make will try
|
|
# the pattern rule with less dependencies that also matches (even with the
|
|
# hard dependency listed).
|
|
$(obj)/zImage.initrd.%: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,$*,,,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/zImage.%: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,$*)
|
|
|
|
# dtbImage% - a dtbImage is a zImage with an embedded device tree blob
|
|
$(obj)/dtbImage.initrd.%: vmlinux $(wrapperbits) $(obj)/%.dtb
|
|
$(call if_changed,wrap,$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/dtbImage.%: vmlinux $(wrapperbits) $(obj)/%.dtb
|
|
$(call if_changed,wrap,$*,,$(obj)/$*.dtb)
|
|
|
|
# This cannot be in the root of $(src) as the zImage rule always adds a $(obj)
|
|
# prefix
|
|
$(obj)/vmlinux.strip: vmlinux
|
|
$(STRIP) -s -R .comment $< -o $@
|
|
|
|
# The iseries hypervisor won't take an ET_DYN executable, so this
|
|
# changes the type (byte 17) in the file to ET_EXEC (2).
|
|
$(obj)/zImage.iseries: vmlinux
|
|
$(STRIP) -s -R .comment $< -o $@
|
|
printf "\x02" | dd of=$@ conv=notrunc bs=1 seek=17
|
|
|
|
$(obj)/uImage: vmlinux $(wrapperbits)
|
|
$(call if_changed,wrap,uboot)
|
|
|
|
$(obj)/cuImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb)
|
|
|
|
$(obj)/simpleImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,simpleboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/simpleImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,simpleboot-$*,,$(obj)/$*.dtb)
|
|
|
|
$(obj)/treeImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,treeboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
|
|
|
|
$(obj)/treeImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
|
|
$(call if_changed,wrap,treeboot-$*,,$(obj)/$*.dtb)
|
|
|
|
# Rule to build device tree blobs
|
|
$(obj)/%.dtb: $(dtstree)/%.dts $(obj)/dtc
|
|
$(obj)/dtc -O dtb -o $(obj)/$*.dtb -b 0 $(DTS_FLAGS) $(dtstree)/$*.dts
|
|
|
|
# If there isn't a platform selected then just strip the vmlinux.
|
|
ifeq (,$(image-y))
|
|
image-y := vmlinux.strip
|
|
endif
|
|
|
|
$(obj)/zImage: $(addprefix $(obj)/, $(image-y))
|
|
@rm -f $@; ln $< $@
|
|
$(obj)/zImage.initrd: $(addprefix $(obj)/, $(initrd-y))
|
|
@rm -f $@; ln $< $@
|
|
|
|
install: $(CONFIGURE) $(addprefix $(obj)/, $(image-y))
|
|
sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $<
|
|
|
|
# anything not in $(targets)
|
|
clean-files += $(image-) $(initrd-) cuImage.* dtbImage.* treeImage.* \
|
|
zImage zImage.initrd zImage.chrp zImage.coff zImage.holly \
|
|
zImage.iseries zImage.miboot zImage.pmac zImage.pseries \
|
|
otheros.bld *.dtb
|
|
|
|
# clean up files cached by wrapper
|
|
clean-kernel := vmlinux.strip vmlinux.bin
|
|
clean-kernel += $(addsuffix .gz,$(clean-kernel))
|
|
# If not absolute clean-files are relative to $(obj).
|
|
clean-files += $(addprefix $(objtree)/, $(clean-kernel))
|
|
|
|
WRAPPER_OBJDIR := /usr/lib/kernel-wrapper
|
|
WRAPPER_DTSDIR := /usr/lib/kernel-wrapper/dts
|
|
WRAPPER_BINDIR := /usr/sbin
|
|
INSTALL := install
|
|
|
|
extra-installed := $(patsubst $(obj)/%, $(DESTDIR)$(WRAPPER_OBJDIR)/%, $(extra-y))
|
|
hostprogs-installed := $(patsubst %, $(DESTDIR)$(WRAPPER_BINDIR)/%, $(hostprogs-y))
|
|
wrapper-installed := $(DESTDIR)$(WRAPPER_BINDIR)/wrapper
|
|
dts-installed := $(patsubst $(obj)/dts/%, $(DESTDIR)$(WRAPPER_DTSDIR)/%, $(wildcard $(obj)/dts/*.dts))
|
|
|
|
all-installed := $(extra-installed) $(hostprogs-installed) $(wrapper-installed) $(dts-installed)
|
|
|
|
quiet_cmd_mkdir = MKDIR $(patsubst $(INSTALL_HDR_PATH)/%,%,$@)
|
|
cmd_mkdir = mkdir -p $@
|
|
|
|
quiet_cmd_install = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_OBJDIR)/%,%,$@)
|
|
cmd_install = $(INSTALL) -m0644 $(patsubst $(DESTDIR)$(WRAPPER_OBJDIR)/%,$(obj)/%,$@) $@
|
|
|
|
quiet_cmd_install_dts = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_DTSDIR)/%,dts/%,$@)
|
|
cmd_install_dts = $(INSTALL) -m0644 $(patsubst $(DESTDIR)$(WRAPPER_DTSDIR)/%,$(srctree)/$(obj)/dts/%,$@) $@
|
|
|
|
quiet_cmd_install_exe = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,%,$@)
|
|
cmd_install_exe = $(INSTALL) -m0755 $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,$(obj)/%,$@) $@
|
|
|
|
quiet_cmd_install_wrapper = INSTALL $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,%,$@)
|
|
cmd_install_wrapper = $(INSTALL) -m0755 $(patsubst $(DESTDIR)$(WRAPPER_BINDIR)/%,$(srctree)/$(obj)/%,$@) $@ ;\
|
|
sed -i $@ -e 's%^object=.*%object=$(WRAPPER_OBJDIR)%' \
|
|
-e 's%^objbin=.*%objbin=$(WRAPPER_BINDIR)%' \
|
|
|
|
|
|
$(DESTDIR)$(WRAPPER_OBJDIR) $(DESTDIR)$(WRAPPER_DTSDIR) $(DESTDIR)$(WRAPPER_BINDIR):
|
|
$(call cmd,mkdir)
|
|
|
|
$(extra-installed) : $(DESTDIR)$(WRAPPER_OBJDIR)/% : $(obj)/% | $(DESTDIR)$(WRAPPER_OBJDIR)
|
|
$(call cmd,install)
|
|
|
|
$(hostprogs-installed) : $(DESTDIR)$(WRAPPER_BINDIR)/% : $(obj)/% | $(DESTDIR)$(WRAPPER_BINDIR)
|
|
$(call cmd,install_exe)
|
|
|
|
$(dts-installed) : $(DESTDIR)$(WRAPPER_DTSDIR)/% : $(srctree)/$(obj)/dts/% | $(DESTDIR)$(WRAPPER_DTSDIR)
|
|
$(call cmd,install_dts)
|
|
|
|
$(wrapper-installed): $(DESTDIR)$(WRAPPER_BINDIR) $(srctree)/$(obj)/wrapper | $(DESTDIR)$(WRAPPER_BINDIR)
|
|
$(call cmd,install_wrapper)
|
|
|
|
$(obj)/bootwrapper_install: $(all-installed)
|
|
|