forked from luck/tmp_suning_uos_patched
f7efad10b5
In this patch, consumers are allowed to set suspend voltage, and this actually just set the "uV" in constraint::regulator_state, when the regulator_suspend_late() was called by PM core through callback when the system is entering into suspend, the regulator device would act suspend activity then. And it assumes that if any consumer set suspend voltage, the regulator device should be enabled in the suspend state. And if the suspend voltage of a regulator device for all consumers was set zero, the regulator device would be off in the suspend state. This patch also provides a new function hook to regulator devices for resuming from suspend states. Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
262 lines
8.5 KiB
C
262 lines
8.5 KiB
C
/*
|
|
* machine.h -- SoC Regulator support, machine/board driver API.
|
|
*
|
|
* Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
|
|
*
|
|
* Author: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* Regulator Machine/Board Interface.
|
|
*/
|
|
|
|
#ifndef __LINUX_REGULATOR_MACHINE_H_
|
|
#define __LINUX_REGULATOR_MACHINE_H_
|
|
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/suspend.h>
|
|
|
|
struct regulator;
|
|
|
|
/*
|
|
* Regulator operation constraint flags. These flags are used to enable
|
|
* certain regulator operations and can be OR'ed together.
|
|
*
|
|
* VOLTAGE: Regulator output voltage can be changed by software on this
|
|
* board/machine.
|
|
* CURRENT: Regulator output current can be changed by software on this
|
|
* board/machine.
|
|
* MODE: Regulator operating mode can be changed by software on this
|
|
* board/machine.
|
|
* STATUS: Regulator can be enabled and disabled.
|
|
* DRMS: Dynamic Regulator Mode Switching is enabled for this regulator.
|
|
* BYPASS: Regulator can be put into bypass mode
|
|
*/
|
|
|
|
#define REGULATOR_CHANGE_VOLTAGE 0x1
|
|
#define REGULATOR_CHANGE_CURRENT 0x2
|
|
#define REGULATOR_CHANGE_MODE 0x4
|
|
#define REGULATOR_CHANGE_STATUS 0x8
|
|
#define REGULATOR_CHANGE_DRMS 0x10
|
|
#define REGULATOR_CHANGE_BYPASS 0x20
|
|
|
|
/*
|
|
* operations in suspend mode
|
|
* DO_NOTHING_IN_SUSPEND - the default value
|
|
* DISABLE_IN_SUSPEND - turn off regulator in suspend states
|
|
* ENABLE_IN_SUSPEND - keep regulator on in suspend states
|
|
*/
|
|
#define DO_NOTHING_IN_SUSPEND (-1)
|
|
#define DISABLE_IN_SUSPEND 0
|
|
#define ENABLE_IN_SUSPEND 1
|
|
|
|
/* Regulator active discharge flags */
|
|
enum regulator_active_discharge {
|
|
REGULATOR_ACTIVE_DISCHARGE_DEFAULT,
|
|
REGULATOR_ACTIVE_DISCHARGE_DISABLE,
|
|
REGULATOR_ACTIVE_DISCHARGE_ENABLE,
|
|
};
|
|
|
|
/**
|
|
* struct regulator_state - regulator state during low power system states
|
|
*
|
|
* This describes a regulators state during a system wide low power
|
|
* state. One of enabled or disabled must be set for the
|
|
* configuration to be applied.
|
|
*
|
|
* @uV: Default operating voltage during suspend, it can be adjusted
|
|
* among <min_uV, max_uV>.
|
|
* @min_uV: Minimum suspend voltage may be set.
|
|
* @max_uV: Maximum suspend voltage may be set.
|
|
* @mode: Operating mode during suspend.
|
|
* @enabled: operations during suspend.
|
|
* - DO_NOTHING_IN_SUSPEND
|
|
* - DISABLE_IN_SUSPEND
|
|
* - ENABLE_IN_SUSPEND
|
|
* @changeable: Is this state can be switched between enabled/disabled,
|
|
*/
|
|
struct regulator_state {
|
|
int uV;
|
|
int min_uV;
|
|
int max_uV;
|
|
unsigned int mode;
|
|
int enabled;
|
|
bool changeable;
|
|
};
|
|
|
|
/**
|
|
* struct regulation_constraints - regulator operating constraints.
|
|
*
|
|
* This struct describes regulator and board/machine specific constraints.
|
|
*
|
|
* @name: Descriptive name for the constraints, used for display purposes.
|
|
*
|
|
* @min_uV: Smallest voltage consumers may set.
|
|
* @max_uV: Largest voltage consumers may set.
|
|
* @uV_offset: Offset applied to voltages from consumer to compensate for
|
|
* voltage drops.
|
|
*
|
|
* @min_uA: Smallest current consumers may set.
|
|
* @max_uA: Largest current consumers may set.
|
|
* @ilim_uA: Maximum input current.
|
|
* @system_load: Load that isn't captured by any consumer requests.
|
|
*
|
|
* @valid_modes_mask: Mask of modes which may be configured by consumers.
|
|
* @valid_ops_mask: Operations which may be performed by consumers.
|
|
*
|
|
* @always_on: Set if the regulator should never be disabled.
|
|
* @boot_on: Set if the regulator is enabled when the system is initially
|
|
* started. If the regulator is not enabled by the hardware or
|
|
* bootloader then it will be enabled when the constraints are
|
|
* applied.
|
|
* @apply_uV: Apply the voltage constraint when initialising.
|
|
* @ramp_disable: Disable ramp delay when initialising or when setting voltage.
|
|
* @soft_start: Enable soft start so that voltage ramps slowly.
|
|
* @pull_down: Enable pull down when regulator is disabled.
|
|
* @over_current_protection: Auto disable on over current event.
|
|
*
|
|
* @input_uV: Input voltage for regulator when supplied by another regulator.
|
|
*
|
|
* @state_disk: State for regulator when system is suspended in disk mode.
|
|
* @state_mem: State for regulator when system is suspended in mem mode.
|
|
* @state_standby: State for regulator when system is suspended in standby
|
|
* mode.
|
|
* @initial_state: Suspend state to set by default.
|
|
* @initial_mode: Mode to set at startup.
|
|
* @ramp_delay: Time to settle down after voltage change (unit: uV/us)
|
|
* @settling_time: Time to settle down after voltage change when voltage
|
|
* change is non-linear (unit: microseconds).
|
|
* @settling_time_up: Time to settle down after voltage increase when voltage
|
|
* change is non-linear (unit: microseconds).
|
|
* @settling_time_down : Time to settle down after voltage decrease when
|
|
* voltage change is non-linear (unit: microseconds).
|
|
* @active_discharge: Enable/disable active discharge. The enum
|
|
* regulator_active_discharge values are used for
|
|
* initialisation.
|
|
* @enable_time: Turn-on time of the rails (unit: microseconds)
|
|
*/
|
|
struct regulation_constraints {
|
|
|
|
const char *name;
|
|
|
|
/* voltage output range (inclusive) - for voltage control */
|
|
int min_uV;
|
|
int max_uV;
|
|
|
|
int uV_offset;
|
|
|
|
/* current output range (inclusive) - for current control */
|
|
int min_uA;
|
|
int max_uA;
|
|
int ilim_uA;
|
|
|
|
int system_load;
|
|
|
|
/* valid regulator operating modes for this machine */
|
|
unsigned int valid_modes_mask;
|
|
|
|
/* valid operations for regulator on this machine */
|
|
unsigned int valid_ops_mask;
|
|
|
|
/* regulator input voltage - only if supply is another regulator */
|
|
int input_uV;
|
|
|
|
/* regulator suspend states for global PMIC STANDBY/HIBERNATE */
|
|
struct regulator_state state_disk;
|
|
struct regulator_state state_mem;
|
|
struct regulator_state state_standby;
|
|
suspend_state_t initial_state; /* suspend state to set at init */
|
|
|
|
/* mode to set on startup */
|
|
unsigned int initial_mode;
|
|
|
|
unsigned int ramp_delay;
|
|
unsigned int settling_time;
|
|
unsigned int settling_time_up;
|
|
unsigned int settling_time_down;
|
|
unsigned int enable_time;
|
|
|
|
unsigned int active_discharge;
|
|
|
|
/* constraint flags */
|
|
unsigned always_on:1; /* regulator never off when system is on */
|
|
unsigned boot_on:1; /* bootloader/firmware enabled regulator */
|
|
unsigned apply_uV:1; /* apply uV constraint if min == max */
|
|
unsigned ramp_disable:1; /* disable ramp delay */
|
|
unsigned soft_start:1; /* ramp voltage slowly */
|
|
unsigned pull_down:1; /* pull down resistor when regulator off */
|
|
unsigned over_current_protection:1; /* auto disable on over current */
|
|
};
|
|
|
|
/**
|
|
* struct regulator_consumer_supply - supply -> device mapping
|
|
*
|
|
* This maps a supply name to a device. Use of dev_name allows support for
|
|
* buses which make struct device available late such as I2C.
|
|
*
|
|
* @dev_name: Result of dev_name() for the consumer.
|
|
* @supply: Name for the supply.
|
|
*/
|
|
struct regulator_consumer_supply {
|
|
const char *dev_name; /* dev_name() for consumer */
|
|
const char *supply; /* consumer supply - e.g. "vcc" */
|
|
};
|
|
|
|
/* Initialize struct regulator_consumer_supply */
|
|
#define REGULATOR_SUPPLY(_name, _dev_name) \
|
|
{ \
|
|
.supply = _name, \
|
|
.dev_name = _dev_name, \
|
|
}
|
|
|
|
/**
|
|
* struct regulator_init_data - regulator platform initialisation data.
|
|
*
|
|
* Initialisation constraints, our supply and consumers supplies.
|
|
*
|
|
* @supply_regulator: Parent regulator. Specified using the regulator name
|
|
* as it appears in the name field in sysfs, which can
|
|
* be explicitly set using the constraints field 'name'.
|
|
*
|
|
* @constraints: Constraints. These must be specified for the regulator to
|
|
* be usable.
|
|
* @num_consumer_supplies: Number of consumer device supplies.
|
|
* @consumer_supplies: Consumer device supply configuration.
|
|
*
|
|
* @regulator_init: Callback invoked when the regulator has been registered.
|
|
* @driver_data: Data passed to regulator_init.
|
|
*/
|
|
struct regulator_init_data {
|
|
const char *supply_regulator; /* or NULL for system supply */
|
|
|
|
struct regulation_constraints constraints;
|
|
|
|
int num_consumer_supplies;
|
|
struct regulator_consumer_supply *consumer_supplies;
|
|
|
|
/* optional regulator machine specific init */
|
|
int (*regulator_init)(void *driver_data);
|
|
void *driver_data; /* core does not touch this */
|
|
};
|
|
|
|
#ifdef CONFIG_REGULATOR
|
|
void regulator_has_full_constraints(void);
|
|
#else
|
|
static inline void regulator_has_full_constraints(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
static inline int regulator_suspend_prepare(suspend_state_t state)
|
|
{
|
|
return 0;
|
|
}
|
|
static inline int regulator_suspend_finish(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#endif
|