kernel_optimize_test/arch/blackfin/mach-bf537/Kconfig
Mike Frysinger 4f25eb85d6 Blackfin arch: split board selection off into mach subdirs
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15 20:49:44 +08:00

117 lines
1.9 KiB
Plaintext

if (BF537 || BF534 || BF536)
source "arch/blackfin/mach-bf537/boards/Kconfig"
menu "BF537 Specific Configuration"
comment "Interrupt Priority Assignment"
menu "Priority"
config IRQ_PLL_WAKEUP
int "IRQ_PLL_WAKEUP"
default 7
config IRQ_DMA_ERROR
int "IRQ_DMA_ERROR Generic"
default 7
config IRQ_ERROR
int "IRQ_ERROR: CAN MAC SPORT0 SPORT1 SPI UART0 UART1"
default 7
config IRQ_RTC
int "IRQ_RTC"
default 8
config IRQ_PPI
int "IRQ_PPI"
default 8
config IRQ_SPORT0_RX
int "IRQ_SPORT0_RX"
default 9
config IRQ_SPORT0_TX
int "IRQ_SPORT0_TX"
default 9
config IRQ_SPORT1_RX
int "IRQ_SPORT1_RX"
default 9
config IRQ_SPORT1_TX
int "IRQ_SPORT1_TX"
default 9
config IRQ_TWI
int "IRQ_TWI"
default 10
config IRQ_SPI
int "IRQ_SPI"
default 10
config IRQ_UART0_RX
int "IRQ_UART0_RX"
default 10
config IRQ_UART0_TX
int "IRQ_UART0_TX"
default 10
config IRQ_UART1_RX
int "IRQ_UART1_RX"
default 10
config IRQ_UART1_TX
int "IRQ_UART1_TX"
default 10
config IRQ_CAN_RX
int "IRQ_CAN_RX"
default 11
config IRQ_CAN_TX
int "IRQ_CAN_TX"
default 11
config IRQ_MAC_RX
int "IRQ_MAC_RX"
default 11
config IRQ_MAC_TX
int "IRQ_MAC_TX"
default 11
config IRQ_TMR0
int "IRQ_TMR0"
default 12
config IRQ_TMR1
int "IRQ_TMR1"
default 12
config IRQ_TMR2
int "IRQ_TMR2"
default 12
config IRQ_TMR3
int "IRQ_TMR3"
default 12
config IRQ_TMR4
int "IRQ_TMR4"
default 12
config IRQ_TMR5
int "IRQ_TMR5"
default 12
config IRQ_TMR6
int "IRQ_TMR6"
default 12
config IRQ_TMR7
int "IRQ_TMR7"
default 12
config IRQ_PROG_INTA
int "IRQ_PROG_INTA"
default 12
config IRQ_PORTG_INTB
int "IRQ_PORTG_INTB"
default 12
config IRQ_MEM_DMA0
int "IRQ_MEM_DMA0"
default 13
config IRQ_MEM_DMA1
int "IRQ_MEM_DMA1"
default 13
config IRQ_WATCH
int "IRQ_WATCH"
default 13
help
Enter the priority numbers between 7-13 ONLY. Others are Reserved.
This applies to all the above. It is not recommended to assign the
highest priority number 7 to UART or any other device.
endmenu
endmenu
endif