forked from luck/tmp_suning_uos_patched
be1229b4c5
Recent feedback from design says we need three NOPs in the hardware loop. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
99 lines
2.4 KiB
ArmAsm
99 lines
2.4 KiB
ArmAsm
/*
|
|
* Blackfin cache control code
|
|
*
|
|
* Copyright 2004-2008 Analog Devices Inc.
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <linux/linkage.h>
|
|
#include <asm/blackfin.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/page.h>
|
|
|
|
#ifdef CONFIG_CACHE_FLUSH_L1
|
|
.section .l1.text
|
|
#else
|
|
.text
|
|
#endif
|
|
|
|
/* 05000443 - IFLUSH cannot be last instruction in hardware loop */
|
|
#if ANOMALY_05000443
|
|
# define BROK_FLUSH_INST "IFLUSH"
|
|
#else
|
|
# define BROK_FLUSH_INST "no anomaly! yeah!"
|
|
#endif
|
|
|
|
/* Since all L1 caches work the same way, we use the same method for flushing
|
|
* them. Only the actual flush instruction differs. We write this in asm as
|
|
* GCC can be hard to coax into writing nice hardware loops.
|
|
*
|
|
* Also, we assume the following register setup:
|
|
* R0 = start address
|
|
* R1 = end address
|
|
*/
|
|
.macro do_flush flushins:req label
|
|
|
|
R2 = -L1_CACHE_BYTES;
|
|
|
|
/* start = (start & -L1_CACHE_BYTES) */
|
|
R0 = R0 & R2;
|
|
|
|
/* end = ((end - 1) & -L1_CACHE_BYTES) + L1_CACHE_BYTES; */
|
|
R1 += -1;
|
|
R1 = R1 & R2;
|
|
R1 += L1_CACHE_BYTES;
|
|
|
|
/* count = (end - start) >> L1_CACHE_SHIFT */
|
|
R2 = R1 - R0;
|
|
R2 >>= L1_CACHE_SHIFT;
|
|
P1 = R2;
|
|
|
|
.ifnb \label
|
|
\label :
|
|
.endif
|
|
P0 = R0;
|
|
|
|
LSETUP (1f, 2f) LC1 = P1;
|
|
1:
|
|
.ifeqs "\flushins", BROK_FLUSH_INST
|
|
\flushins [P0++];
|
|
nop;
|
|
nop;
|
|
2: nop;
|
|
.else
|
|
2: \flushins [P0++];
|
|
.endif
|
|
|
|
RTS;
|
|
.endm
|
|
|
|
/* Invalidate all instruction cache lines assocoiated with this memory area */
|
|
ENTRY(_blackfin_icache_flush_range)
|
|
do_flush IFLUSH
|
|
ENDPROC(_blackfin_icache_flush_range)
|
|
|
|
/* Throw away all D-cached data in specified region without any obligation to
|
|
* write them back. Since the Blackfin ISA does not have an "invalidate"
|
|
* instruction, we use flush/invalidate. Perhaps as a speed optimization we
|
|
* could bang on the DTEST MMRs ...
|
|
*/
|
|
ENTRY(_blackfin_dcache_invalidate_range)
|
|
do_flush FLUSHINV
|
|
ENDPROC(_blackfin_dcache_invalidate_range)
|
|
|
|
/* Flush all data cache lines assocoiated with this memory area */
|
|
ENTRY(_blackfin_dcache_flush_range)
|
|
do_flush FLUSH, .Ldfr
|
|
ENDPROC(_blackfin_dcache_flush_range)
|
|
|
|
/* Our headers convert the page structure to an address, so just need to flush
|
|
* its contents like normal. We know the start address is page aligned (which
|
|
* greater than our cache alignment), as is the end address. So just jump into
|
|
* the middle of the dcache flush function.
|
|
*/
|
|
ENTRY(_blackfin_dflush_page)
|
|
P1 = 1 << (PAGE_SHIFT - L1_CACHE_SHIFT);
|
|
jump .Ldfr;
|
|
ENDPROC(_blackfin_dflush_page)
|