AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
5aa83a4c0a
kernel_optimize_test/drivers/serial/serial_txx9.c
Pavel Machek 0370affeec [PATCH] fix u32 vs. pm_message_t in drivers/ 
-rc2-mm1 still contains few places where u32 and pm_message_t.  This fixes
drivers/serial [should change no code].

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:25:35 -07:00

1172 lines
30 KiB
C
Raw Blame History

/*
* drivers/serial/serial_txx9.c
*
* Derived from many drivers using generic_serial interface,
* especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
* (was in Linux/VR tree) by Jim Pick.
*
* Copyright (C) 1999 Harald Koerfgen
* Copyright (C) 2000 Jim Pick <jim@jimpick.com>
* Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
* Copyright (C) 2000-2002 Toshiba Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
*
* Revision History:
* 0.30 Initial revision. (Renamed from serial_txx927.c)
* 0.31 Use save_flags instead of local_irq_save.
* 0.32 Support SCLK.
* 0.33 Switch TXX9_TTY_NAME by CONFIG_SERIAL_TXX9_STDSERIAL.
* Support TIOCSERGETLSR.
* 0.34 Support slow baudrate.
* 0.40 Merge codes from mainstream kernel (2.4.22).
* 0.41 Fix console checking in rs_shutdown_port().
* Disable flow-control in serial_console_write().
* 0.42 Fix minor compiler warning.
* 1.00 Kernel 2.6. Converted to new serial core (based on 8250.c).
* 1.01 Set fifosize to make tx_empry called properly.
* Use standard uart_get_divisor.
* 1.02 Cleanup. (import 8250.c changes)
*/
#include <linux/config.h>
#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/pci.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <asm/io.h>
#include <asm/irq.h>
static char *serial_version = "1.02";
static char *serial_name = "TX39/49 Serial driver";
#define PASS_LIMIT 256
#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
/* "ttyS" is used for standard serial driver */
#define TXX9_TTY_NAME "ttyTX"
#define TXX9_TTY_DEVFS_NAME "tttx/"
#define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */
#else
/* acts like standard serial driver */
#define TXX9_TTY_NAME "ttyS"
#define TXX9_TTY_DEVFS_NAME "tts/"
#define TXX9_TTY_MINOR_START 64
#endif
#define TXX9_TTY_MAJOR TTY_MAJOR
/* flag aliases */
#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
#ifdef CONFIG_PCI
/* support for Toshiba TC86C001 SIO */
#define ENABLE_SERIAL_TXX9_PCI
#endif
/*
* Number of serial ports
*/
#ifdef ENABLE_SERIAL_TXX9_PCI
#define NR_PCI_BOARDS 4
#define UART_NR (2 + NR_PCI_BOARDS)
#else
#define UART_NR 2
#endif
struct uart_txx9_port {
struct uart_port port;
/*
* We provide a per-port pm hook.
*/
void (*pm)(struct uart_port *port,
unsigned int state, unsigned int old);
};
#define TXX9_REGION_SIZE 0x24
/* TXX9 Serial Registers */
#define TXX9_SILCR 0x00
#define TXX9_SIDICR 0x04
#define TXX9_SIDISR 0x08
#define TXX9_SICISR 0x0c
#define TXX9_SIFCR 0x10
#define TXX9_SIFLCR 0x14
#define TXX9_SIBGR 0x18
#define TXX9_SITFIFO 0x1c
#define TXX9_SIRFIFO 0x20
/* SILCR : Line Control */
#define TXX9_SILCR_SCS_MASK 0x00000060
#define TXX9_SILCR_SCS_IMCLK 0x00000000
#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
#define TXX9_SILCR_SCS_SCLK 0x00000040
#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
#define TXX9_SILCR_UEPS 0x00000010
#define TXX9_SILCR_UPEN 0x00000008
#define TXX9_SILCR_USBL_MASK 0x00000004
#define TXX9_SILCR_USBL_1BIT 0x00000000
#define TXX9_SILCR_USBL_2BIT 0x00000004
#define TXX9_SILCR_UMODE_MASK 0x00000003
#define TXX9_SILCR_UMODE_8BIT 0x00000000
#define TXX9_SILCR_UMODE_7BIT 0x00000001
/* SIDICR : DMA/Int. Control */
#define TXX9_SIDICR_TDE 0x00008000
#define TXX9_SIDICR_RDE 0x00004000
#define TXX9_SIDICR_TIE 0x00002000
#define TXX9_SIDICR_RIE 0x00001000
#define TXX9_SIDICR_SPIE 0x00000800
#define TXX9_SIDICR_CTSAC 0x00000600
#define TXX9_SIDICR_STIE_MASK 0x0000003f
#define TXX9_SIDICR_STIE_OERS 0x00000020
#define TXX9_SIDICR_STIE_CTSS 0x00000010
#define TXX9_SIDICR_STIE_RBRKD 0x00000008
#define TXX9_SIDICR_STIE_TRDY 0x00000004
#define TXX9_SIDICR_STIE_TXALS 0x00000002
#define TXX9_SIDICR_STIE_UBRKD 0x00000001
/* SIDISR : DMA/Int. Status */
#define TXX9_SIDISR_UBRK 0x00008000
#define TXX9_SIDISR_UVALID 0x00004000
#define TXX9_SIDISR_UFER 0x00002000
#define TXX9_SIDISR_UPER 0x00001000
#define TXX9_SIDISR_UOER 0x00000800
#define TXX9_SIDISR_ERI 0x00000400
#define TXX9_SIDISR_TOUT 0x00000200
#define TXX9_SIDISR_TDIS 0x00000100
#define TXX9_SIDISR_RDIS 0x00000080
#define TXX9_SIDISR_STIS 0x00000040
#define TXX9_SIDISR_RFDN_MASK 0x0000001f
/* SICISR : Change Int. Status */
#define TXX9_SICISR_OERS 0x00000020
#define TXX9_SICISR_CTSS 0x00000010
#define TXX9_SICISR_RBRKD 0x00000008
#define TXX9_SICISR_TRDY 0x00000004
#define TXX9_SICISR_TXALS 0x00000002
#define TXX9_SICISR_UBRKD 0x00000001
/* SIFCR : FIFO Control */
#define TXX9_SIFCR_SWRST 0x00008000
#define TXX9_SIFCR_RDIL_MASK 0x00000180
#define TXX9_SIFCR_RDIL_1 0x00000000
#define TXX9_SIFCR_RDIL_4 0x00000080
#define TXX9_SIFCR_RDIL_8 0x00000100
#define TXX9_SIFCR_RDIL_12 0x00000180
#define TXX9_SIFCR_RDIL_MAX 0x00000180
#define TXX9_SIFCR_TDIL_MASK 0x00000018
#define TXX9_SIFCR_TDIL_MASK 0x00000018
#define TXX9_SIFCR_TDIL_1 0x00000000
#define TXX9_SIFCR_TDIL_4 0x00000001
#define TXX9_SIFCR_TDIL_8 0x00000010
#define TXX9_SIFCR_TDIL_MAX 0x00000010
#define TXX9_SIFCR_TFRST 0x00000004
#define TXX9_SIFCR_RFRST 0x00000002
#define TXX9_SIFCR_FRSTE 0x00000001
#define TXX9_SIO_TX_FIFO 8
#define TXX9_SIO_RX_FIFO 16
/* SIFLCR : Flow Control */
#define TXX9_SIFLCR_RCS 0x00001000
#define TXX9_SIFLCR_TES 0x00000800
#define TXX9_SIFLCR_RTSSC 0x00000200
#define TXX9_SIFLCR_RSDE 0x00000100
#define TXX9_SIFLCR_TSDE 0x00000080
#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
#define TXX9_SIFLCR_TBRK 0x00000001
/* SIBGR : Baudrate Control */
#define TXX9_SIBGR_BCLK_MASK 0x00000300
#define TXX9_SIBGR_BCLK_T0 0x00000000
#define TXX9_SIBGR_BCLK_T2 0x00000100
#define TXX9_SIBGR_BCLK_T4 0x00000200
#define TXX9_SIBGR_BCLK_T6 0x00000300
#define TXX9_SIBGR_BRD_MASK 0x000000ff
static inline unsigned int sio_in(struct uart_txx9_port *up, int offset)
{
switch (up->port.iotype) {
default:
return *(volatile u32 *)(up->port.membase + offset);
case UPIO_PORT:
return inl(up->port.iobase + offset);
}
}
static inline void
sio_out(struct uart_txx9_port *up, int offset, int value)
{
switch (up->port.iotype) {
default:
*(volatile u32 *)(up->port.membase + offset) = value;
break;
case UPIO_PORT:
outl(value, up->port.iobase + offset);
break;
}
}
static inline void
sio_mask(struct uart_txx9_port *up, int offset, unsigned int value)
{
sio_out(up, offset, sio_in(up, offset) & ~value);
}
static inline void
sio_set(struct uart_txx9_port *up, int offset, unsigned int value)
{
sio_out(up, offset, sio_in(up, offset) | value);
}
static inline void
sio_quot_set(struct uart_txx9_port *up, int quot)
{
quot >>= 1;
if (quot < 256)
sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
else if (quot < (256 << 2))
sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
else if (quot < (256 << 4))
sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
else if (quot < (256 << 6))
sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
else
sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
}
static void serial_txx9_stop_tx(struct uart_port *port, unsigned int tty_stop)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void serial_txx9_start_tx(struct uart_port *port, unsigned int tty_start)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void serial_txx9_stop_rx(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
#if 0
sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
#endif
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void serial_txx9_enable_ms(struct uart_port *port)
{
/* TXX9-SIO can not control DTR... */
}
static inline void
receive_chars(struct uart_txx9_port *up, unsigned int *status, struct pt_regs *regs)
{
struct tty_struct *tty = up->port.info->tty;
unsigned char ch;
unsigned int disr = *status;
int max_count = 256;
char flag;
do {
/* The following is not allowed by the tty layer and
unsafe. It should be fixed ASAP */
if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
if(tty->low_latency)
tty_flip_buffer_push(tty);
/* If this failed then we will throw away the
bytes but must do so to clear interrupts */
}
ch = sio_in(up, TXX9_SIRFIFO);
flag = TTY_NORMAL;
up->port.icount.rx++;
if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
/*
* For statistics only
*/
if (disr & TXX9_SIDISR_UBRK) {
disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
up->port.icount.brk++;
/*
* We do the SysRQ and SAK checking
* here because otherwise the break
* may get masked by ignore_status_mask
* or read_status_mask.
*/
if (uart_handle_break(&up->port))
goto ignore_char;
} else if (disr & TXX9_SIDISR_UPER)
up->port.icount.parity++;
else if (disr & TXX9_SIDISR_UFER)
up->port.icount.frame++;
if (disr & TXX9_SIDISR_UOER)
up->port.icount.overrun++;
/*
* Mask off conditions which should be ingored.
*/
disr &= up->port.read_status_mask;
if (disr & TXX9_SIDISR_UBRK) {
flag = TTY_BREAK;
} else if (disr & TXX9_SIDISR_UPER)
flag = TTY_PARITY;
else if (disr & TXX9_SIDISR_UFER)
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch, regs))
goto ignore_char;
if ((disr & up->port.ignore_status_mask) == 0) {
tty_insert_flip_char(tty, ch, flag);
}
if ((disr & TXX9_SIDISR_UOER) &&
tty->flip.count < TTY_FLIPBUF_SIZE) {
/*
* Overrun is special, since it's reported
* immediately, and doesn't affect the current
* character.
*/
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
}
ignore_char:
disr = sio_in(up, TXX9_SIDISR);
} while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
tty_flip_buffer_push(tty);
*status = disr;
}
static inline void transmit_chars(struct uart_txx9_port *up)
{
struct circ_buf *xmit = &up->port.info->xmit;
int count;
if (up->port.x_char) {
sio_out(up, TXX9_SITFIFO, up->port.x_char);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
serial_txx9_stop_tx(&up->port, 0);
return;
}
count = TXX9_SIO_TX_FIFO;
do {
sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
if (uart_circ_empty(xmit))
serial_txx9_stop_tx(&up->port, 0);
}
static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
int pass_counter = 0;
struct uart_txx9_port *up = dev_id;
unsigned int status;
while (1) {
spin_lock(&up->port.lock);
status = sio_in(up, TXX9_SIDISR);
if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
status &= ~TXX9_SIDISR_TDIS;
if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
TXX9_SIDISR_TOUT))) {
spin_unlock(&up->port.lock);
break;
}
if (status & TXX9_SIDISR_RDIS)
receive_chars(up, &status, regs);
if (status & TXX9_SIDISR_TDIS)
transmit_chars(up);
/* Clear TX/RX Int. Status */
sio_mask(up, TXX9_SIDISR,
TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
TXX9_SIDISR_TOUT);
spin_unlock(&up->port.lock);
if (pass_counter++ > PASS_LIMIT)
break;
}
return pass_counter ? IRQ_HANDLED : IRQ_NONE;
}
static unsigned int serial_txx9_tx_empty(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
ret = ((sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS)
| ((sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS);
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
if (mctrl & TIOCM_RTS)
sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
else
sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
if (break_state == -1)
sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
else
sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static int serial_txx9_startup(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
int retval;
/*
* Clear the FIFO buffers and disable them.
* (they will be reeanbled in set_termios())
*/
sio_set(up, TXX9_SIFCR,
TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
/* clear reset */
sio_mask(up, TXX9_SIFCR,
TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
sio_out(up, TXX9_SIDICR, 0);
/*
* Clear the interrupt registers.
*/
sio_out(up, TXX9_SIDISR, 0);
retval = request_irq(up->port.irq, serial_txx9_interrupt,
SA_SHIRQ, "serial_txx9", up);
if (retval)
return retval;
/*
* Now, initialize the UART
*/
spin_lock_irqsave(&up->port.lock, flags);
serial_txx9_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/* Enable RX/TX */
sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
/*
* Finally, enable interrupts.
*/
sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
return 0;
}
static void serial_txx9_shutdown(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
/*
* Disable interrupts from this port
*/
sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
spin_lock_irqsave(&up->port.lock, flags);
serial_txx9_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Disable break condition
*/
sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
if (up->port.cons && up->port.line == up->port.cons->index) {
free_irq(up->port.irq, up);
return;
}
#endif
/* reset FIFOs */
sio_set(up, TXX9_SIFCR,
TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
/* clear reset */
sio_mask(up, TXX9_SIFCR,
TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
/* Disable RX/TX */
sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
free_irq(up->port.irq, up);
}
static void
serial_txx9_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned int cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
cval = sio_in(up, TXX9_SILCR);
/* byte size and parity */
cval &= ~TXX9_SILCR_UMODE_MASK;
switch (termios->c_cflag & CSIZE) {
case CS7:
cval |= TXX9_SILCR_UMODE_7BIT;
break;
default:
case CS5: /* not supported */
case CS6: /* not supported */
case CS8:
cval |= TXX9_SILCR_UMODE_8BIT;
break;
}
cval &= ~TXX9_SILCR_USBL_MASK;
if (termios->c_cflag & CSTOPB)
cval |= TXX9_SILCR_USBL_2BIT;
else
cval |= TXX9_SILCR_USBL_1BIT;
cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
if (termios->c_cflag & PARENB)
cval |= TXX9_SILCR_UPEN;
if (!(termios->c_cflag & PARODD))
cval |= TXX9_SILCR_UEPS;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2);
quot = uart_get_divisor(port, baud);
/* Set up FIFOs */
/* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = TXX9_SIDISR_UOER |
TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= TXX9_SIDISR_UBRK;
/*
* Characteres to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= TXX9_SIDISR_UBRK;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= TXX9_SIDISR_UOER;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= TXX9_SIDISR_RDIS;
/* CTS flow control flag */
if ((termios->c_cflag & CRTSCTS) &&
(up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) {
sio_set(up, TXX9_SIFLCR,
TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
} else {
sio_mask(up, TXX9_SIFLCR,
TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
}
sio_out(up, TXX9_SILCR, cval);
sio_quot_set(up, quot);
sio_out(up, TXX9_SIFCR, fcr);
serial_txx9_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void
serial_txx9_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
if (state) {
/* sleep */
if (up->pm)
up->pm(port, state, oldstate);
} else {
/* wake */
if (up->pm)
up->pm(port, state, oldstate);
}
}
static int serial_txx9_request_resource(struct uart_txx9_port *up)
{
unsigned int size = TXX9_REGION_SIZE;
int ret = 0;
switch (up->port.iotype) {
default:
if (!up->port.mapbase)
break;
if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) {
ret = -EBUSY;
break;
}
if (up->port.flags & UPF_IOREMAP) {
up->port.membase = ioremap(up->port.mapbase, size);
if (!up->port.membase) {
release_mem_region(up->port.mapbase, size);
ret = -ENOMEM;
}
}
break;
case UPIO_PORT:
if (!request_region(up->port.iobase, size, "serial_txx9"))
ret = -EBUSY;
break;
}
return ret;
}
static void serial_txx9_release_resource(struct uart_txx9_port *up)
{
unsigned int size = TXX9_REGION_SIZE;
switch (up->port.iotype) {
default:
if (!up->port.mapbase)
break;
if (up->port.flags & UPF_IOREMAP) {
iounmap(up->port.membase);
up->port.membase = NULL;
}
release_mem_region(up->port.mapbase, size);
break;
case UPIO_PORT:
release_region(up->port.iobase, size);
break;
}
}
static void serial_txx9_release_port(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
serial_txx9_release_resource(up);
}
static int serial_txx9_request_port(struct uart_port *port)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
return serial_txx9_request_resource(up);
}
static void serial_txx9_config_port(struct uart_port *port, int uflags)
{
struct uart_txx9_port *up = (struct uart_txx9_port *)port;
unsigned long flags;
int ret;
/*
* Find the region that we can probe for. This in turn
* tells us whether we can probe for the type of port.
*/
ret = serial_txx9_request_resource(up);
if (ret < 0)
return;
port->type = PORT_TXX9;
up->port.fifosize = TXX9_SIO_TX_FIFO;
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
if (up->port.line == up->port.cons->index)
return;
#endif
spin_lock_irqsave(&up->port.lock, flags);
/*
* Reset the UART.
*/
sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
#ifdef CONFIG_CPU_TX49XX
/* TX4925 BUG WORKAROUND. Accessing SIOC register
* immediately after soft reset causes bus error. */
iob();
udelay(1);
#endif
while (sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST)
;
/* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
sio_set(up, TXX9_SIFCR,
TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
/* initial settings */
sio_out(up, TXX9_SILCR,
TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
((up->port.flags & UPF_TXX9_USE_SCLK) ?
TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
sio_quot_set(up, uart_get_divisor(port, 9600));
sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static int
serial_txx9_verify_port(struct uart_port *port, struct serial_struct *ser)
{
if (ser->irq < 0 ||
ser->baud_base < 9600 || ser->type != PORT_TXX9)
return -EINVAL;
return 0;
}
static const char *
serial_txx9_type(struct uart_port *port)
{
return "txx9";
}
static struct uart_ops serial_txx9_pops = {
.tx_empty = serial_txx9_tx_empty,
.set_mctrl = serial_txx9_set_mctrl,
.get_mctrl = serial_txx9_get_mctrl,
.stop_tx = serial_txx9_stop_tx,
.start_tx = serial_txx9_start_tx,
.stop_rx = serial_txx9_stop_rx,
.enable_ms = serial_txx9_enable_ms,
.break_ctl = serial_txx9_break_ctl,
.startup = serial_txx9_startup,
.shutdown = serial_txx9_shutdown,
.set_termios = serial_txx9_set_termios,
.pm = serial_txx9_pm,
.type = serial_txx9_type,
.release_port = serial_txx9_release_port,
.request_port = serial_txx9_request_port,
.config_port = serial_txx9_config_port,
.verify_port = serial_txx9_verify_port,
};
static struct uart_txx9_port serial_txx9_ports[UART_NR];
static void __init serial_txx9_register_ports(struct uart_driver *drv)
{
int i;
for (i = 0; i < UART_NR; i++) {
struct uart_txx9_port *up = &serial_txx9_ports[i];
up->port.line = i;
up->port.ops = &serial_txx9_pops;
uart_add_one_port(drv, &up->port);
}
}
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
/*
* Wait for transmitter & holding register to empty
*/
static inline void wait_for_xmitr(struct uart_txx9_port *up)
{
unsigned int tmout = 10000;
/* Wait up to 10ms for the character(s) to be sent. */
while (--tmout &&
!(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
udelay(1);
/* Wait up to 1s for flow control if necessary */
if (up->port.flags & UPF_CONS_FLOW) {
tmout = 1000000;
while (--tmout &&
(sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
udelay(1);
}
}
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_txx9_port *up = &serial_txx9_ports[co->index];
unsigned int ier, flcr;
int i;
/*
* First save the UER then disable the interrupts
*/
ier = sio_in(up, TXX9_SIDICR);
sio_out(up, TXX9_SIDICR, 0);
/*
* Disable flow-control if enabled (and unnecessary)
*/
flcr = sio_in(up, TXX9_SIFLCR);
if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
/*
* Now, do each character
*/
for (i = 0; i < count; i++, s++) {
wait_for_xmitr(up);
/*
* Send the character out.
* If a LF, also do CR...
*/
sio_out(up, TXX9_SITFIFO, *s);
if (*s == 10) {
wait_for_xmitr(up);
sio_out(up, TXX9_SITFIFO, 13);
}
}
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
sio_out(up, TXX9_SIFLCR, flcr);
sio_out(up, TXX9_SIDICR, ier);
}
static int serial_txx9_console_setup(struct console *co, char *options)
{
struct uart_port *port;
struct uart_txx9_port *up;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index >= UART_NR)
co->index = 0;
up = &serial_txx9_ports[co->index];
port = &up->port;
if (!port->ops)
return -ENODEV;
/*
* Temporary fix.
*/
spin_lock_init(&port->lock);
/*
* Disable UART interrupts, set DTR and RTS high
* and set speed.
*/
sio_out(up, TXX9_SIDICR, 0);
/* initial settings */
sio_out(up, TXX9_SILCR,
TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
((port->flags & UPF_TXX9_USE_SCLK) ?
TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
return uart_set_options(port, co, baud, parity, bits, flow);
}
static struct uart_driver serial_txx9_reg;
static struct console serial_txx9_console = {
.name = TXX9_TTY_NAME,
.write = serial_txx9_console_write,
.device = uart_console_device,
.setup = serial_txx9_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &serial_txx9_reg,
};
static int __init serial_txx9_console_init(void)
{
register_console(&serial_txx9_console);
return 0;
}
console_initcall(serial_txx9_console_init);
static int __init serial_txx9_late_console_init(void)
{
if (!(serial_txx9_console.flags & CON_ENABLED))
register_console(&serial_txx9_console);
return 0;
}
late_initcall(serial_txx9_late_console_init);
#define SERIAL_TXX9_CONSOLE &serial_txx9_console
#else
#define SERIAL_TXX9_CONSOLE NULL
#endif
static struct uart_driver serial_txx9_reg = {
.owner = THIS_MODULE,
.driver_name = "serial_txx9",
.devfs_name = TXX9_TTY_DEVFS_NAME,
.dev_name = TXX9_TTY_NAME,
.major = TXX9_TTY_MAJOR,
.minor = TXX9_TTY_MINOR_START,
.nr = UART_NR,
.cons = SERIAL_TXX9_CONSOLE,
};
int __init early_serial_txx9_setup(struct uart_port *port)
{
if (port->line >= ARRAY_SIZE(serial_txx9_ports))
return -ENODEV;
serial_txx9_ports[port->line].port = *port;
serial_txx9_ports[port->line].port.ops = &serial_txx9_pops;
serial_txx9_ports[port->line].port.flags |= UPF_BOOT_AUTOCONF;
return 0;
}
#ifdef ENABLE_SERIAL_TXX9_PCI
/**
* serial_txx9_suspend_port - suspend one serial port
* @line: serial line number
* @level: the level of port suspension, as per uart_suspend_port
*
* Suspend one serial port.
*/
static void serial_txx9_suspend_port(int line)
{
uart_suspend_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
}
/**
* serial_txx9_resume_port - resume one serial port
* @line: serial line number
* @level: the level of port resumption, as per uart_resume_port
*
* Resume one serial port.
*/
static void serial_txx9_resume_port(int line)
{
uart_resume_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
}
/*
* Probe one serial board. Unfortunately, there is no rhyme nor reason
* to the arrangement of serial ports on a PCI card.
*/
static int __devinit
pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
{
struct uart_port port;
int line;
int rc;
rc = pci_enable_device(dev);
if (rc)
return rc;
memset(&port, 0, sizeof(port));
port.ops = &serial_txx9_pops;
port.flags |= UPF_BOOT_AUTOCONF; /* uart_ops.config_port will be called */
port.flags |= UPF_TXX9_HAVE_CTS_LINE;
port.uartclk = 66670000;
port.irq = dev->irq;
port.iotype = UPIO_PORT;
port.iobase = pci_resource_start(dev, 1);
line = uart_register_port(&serial_txx9_reg, &port);
if (line < 0) {
printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
}
pci_set_drvdata(dev, (void *)(long)line);
return 0;
}
static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
{
int line = (int)(long)pci_get_drvdata(dev);
pci_set_drvdata(dev, NULL);
if (line) {
uart_unregister_port(&serial_txx9_reg, line);
pci_disable_device(dev);
}
}
static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
{
int line = (int)(long)pci_get_drvdata(dev);
if (line)
serial_txx9_suspend_port(line);
return 0;
}
static int pciserial_txx9_resume_one(struct pci_dev *dev)
{
int line = (int)(long)pci_get_drvdata(dev);
if (line)
serial_txx9_resume_port(line);
return 0;
}
static struct pci_device_id serial_txx9_pci_tbl[] = {
{ PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC,
PCI_ANY_ID, PCI_ANY_ID,
0, 0, 0 },
{ 0, }
};
static struct pci_driver serial_txx9_pci_driver = {
.name = "serial_txx9",
.probe = pciserial_txx9_init_one,
.remove = __devexit_p(pciserial_txx9_remove_one),
.suspend = pciserial_txx9_suspend_one,
.resume = pciserial_txx9_resume_one,
.id_table = serial_txx9_pci_tbl,
};
MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
#endif /* ENABLE_SERIAL_TXX9_PCI */
static int __init serial_txx9_init(void)
{
int ret;
printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
ret = uart_register_driver(&serial_txx9_reg);
if (ret >= 0) {
serial_txx9_register_ports(&serial_txx9_reg);
#ifdef ENABLE_SERIAL_TXX9_PCI
ret = pci_module_init(&serial_txx9_pci_driver);
#endif
}
return ret;
}
static void __exit serial_txx9_exit(void)
{
int i;
#ifdef ENABLE_SERIAL_TXX9_PCI
pci_unregister_driver(&serial_txx9_pci_driver);
#endif
for (i = 0; i < UART_NR; i++)
uart_remove_one_port(&serial_txx9_reg, &serial_txx9_ports[i].port);
uart_unregister_driver(&serial_txx9_reg);
}
module_init(serial_txx9_init);
module_exit(serial_txx9_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("TX39/49 serial driver");
MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);
View Git Blame Copy Permalink