forked from luck/tmp_suning_uos_patched
6ac77e469e
The GIC register accesses today make use of readl()/writel() which prove to be very expensive when used along with mandatory barriers. This mandatory barriers also introduces an un-necessary and expensive l2x0_sync() operation. On Cortex-A9 MP cores, GIC IO accesses from CPU are direct and doesn't go through L2X0 write buffer. A DSB before writel_relaxed() in gic_raise_softirq() is added to be compliant with the Barrier Litmus document - the mailbox scenario. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com>
404 lines
9.8 KiB
C
404 lines
9.8 KiB
C
/*
|
|
* linux/arch/arm/common/gic.c
|
|
*
|
|
* Copyright (C) 2002 ARM Limited, All Rights Reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* Interrupt architecture for the GIC:
|
|
*
|
|
* o There is one Interrupt Distributor, which receives interrupts
|
|
* from system devices and sends them to the Interrupt Controllers.
|
|
*
|
|
* o There is one CPU Interface per CPU, which sends interrupts sent
|
|
* by the Distributor, and interrupts generated locally, to the
|
|
* associated CPU. The base address of the CPU interface is usually
|
|
* aliased so that the same address points to different chips depending
|
|
* on the CPU it is accessed from.
|
|
*
|
|
* Note that IRQs 0-31 are special - they are local to each CPU.
|
|
* As such, the enable set/clear, pending set/clear and active bit
|
|
* registers are banked per-cpu for these sources.
|
|
*/
|
|
#include <linux/init.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/list.h>
|
|
#include <linux/smp.h>
|
|
#include <linux/cpumask.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <asm/irq.h>
|
|
#include <asm/mach/irq.h>
|
|
#include <asm/hardware/gic.h>
|
|
|
|
static DEFINE_SPINLOCK(irq_controller_lock);
|
|
|
|
/* Address of GIC 0 CPU interface */
|
|
void __iomem *gic_cpu_base_addr __read_mostly;
|
|
|
|
struct gic_chip_data {
|
|
unsigned int irq_offset;
|
|
void __iomem *dist_base;
|
|
void __iomem *cpu_base;
|
|
};
|
|
|
|
/*
|
|
* Supported arch specific GIC irq extension.
|
|
* Default make them NULL.
|
|
*/
|
|
struct irq_chip gic_arch_extn = {
|
|
.irq_eoi = NULL,
|
|
.irq_mask = NULL,
|
|
.irq_unmask = NULL,
|
|
.irq_retrigger = NULL,
|
|
.irq_set_type = NULL,
|
|
.irq_set_wake = NULL,
|
|
};
|
|
|
|
#ifndef MAX_GIC_NR
|
|
#define MAX_GIC_NR 1
|
|
#endif
|
|
|
|
static struct gic_chip_data gic_data[MAX_GIC_NR] __read_mostly;
|
|
|
|
static inline void __iomem *gic_dist_base(struct irq_data *d)
|
|
{
|
|
struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
|
|
return gic_data->dist_base;
|
|
}
|
|
|
|
static inline void __iomem *gic_cpu_base(struct irq_data *d)
|
|
{
|
|
struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
|
|
return gic_data->cpu_base;
|
|
}
|
|
|
|
static inline unsigned int gic_irq(struct irq_data *d)
|
|
{
|
|
struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d);
|
|
return d->irq - gic_data->irq_offset;
|
|
}
|
|
|
|
/*
|
|
* Routines to acknowledge, disable and enable interrupts
|
|
*/
|
|
static void gic_mask_irq(struct irq_data *d)
|
|
{
|
|
u32 mask = 1 << (d->irq % 32);
|
|
|
|
spin_lock(&irq_controller_lock);
|
|
writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_CLEAR + (gic_irq(d) / 32) * 4);
|
|
if (gic_arch_extn.irq_mask)
|
|
gic_arch_extn.irq_mask(d);
|
|
spin_unlock(&irq_controller_lock);
|
|
}
|
|
|
|
static void gic_unmask_irq(struct irq_data *d)
|
|
{
|
|
u32 mask = 1 << (d->irq % 32);
|
|
|
|
spin_lock(&irq_controller_lock);
|
|
if (gic_arch_extn.irq_unmask)
|
|
gic_arch_extn.irq_unmask(d);
|
|
writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_SET + (gic_irq(d) / 32) * 4);
|
|
spin_unlock(&irq_controller_lock);
|
|
}
|
|
|
|
static void gic_eoi_irq(struct irq_data *d)
|
|
{
|
|
if (gic_arch_extn.irq_eoi) {
|
|
spin_lock(&irq_controller_lock);
|
|
gic_arch_extn.irq_eoi(d);
|
|
spin_unlock(&irq_controller_lock);
|
|
}
|
|
|
|
writel_relaxed(gic_irq(d), gic_cpu_base(d) + GIC_CPU_EOI);
|
|
}
|
|
|
|
static int gic_set_type(struct irq_data *d, unsigned int type)
|
|
{
|
|
void __iomem *base = gic_dist_base(d);
|
|
unsigned int gicirq = gic_irq(d);
|
|
u32 enablemask = 1 << (gicirq % 32);
|
|
u32 enableoff = (gicirq / 32) * 4;
|
|
u32 confmask = 0x2 << ((gicirq % 16) * 2);
|
|
u32 confoff = (gicirq / 16) * 4;
|
|
bool enabled = false;
|
|
u32 val;
|
|
|
|
/* Interrupt configuration for SGIs can't be changed */
|
|
if (gicirq < 16)
|
|
return -EINVAL;
|
|
|
|
if (type != IRQ_TYPE_LEVEL_HIGH && type != IRQ_TYPE_EDGE_RISING)
|
|
return -EINVAL;
|
|
|
|
spin_lock(&irq_controller_lock);
|
|
|
|
if (gic_arch_extn.irq_set_type)
|
|
gic_arch_extn.irq_set_type(d, type);
|
|
|
|
val = readl_relaxed(base + GIC_DIST_CONFIG + confoff);
|
|
if (type == IRQ_TYPE_LEVEL_HIGH)
|
|
val &= ~confmask;
|
|
else if (type == IRQ_TYPE_EDGE_RISING)
|
|
val |= confmask;
|
|
|
|
/*
|
|
* As recommended by the spec, disable the interrupt before changing
|
|
* the configuration
|
|
*/
|
|
if (readl_relaxed(base + GIC_DIST_ENABLE_SET + enableoff) & enablemask) {
|
|
writel_relaxed(enablemask, base + GIC_DIST_ENABLE_CLEAR + enableoff);
|
|
enabled = true;
|
|
}
|
|
|
|
writel_relaxed(val, base + GIC_DIST_CONFIG + confoff);
|
|
|
|
if (enabled)
|
|
writel_relaxed(enablemask, base + GIC_DIST_ENABLE_SET + enableoff);
|
|
|
|
spin_unlock(&irq_controller_lock);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gic_retrigger(struct irq_data *d)
|
|
{
|
|
if (gic_arch_extn.irq_retrigger)
|
|
return gic_arch_extn.irq_retrigger(d);
|
|
|
|
return -ENXIO;
|
|
}
|
|
|
|
#ifdef CONFIG_SMP
|
|
static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val,
|
|
bool force)
|
|
{
|
|
void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3);
|
|
unsigned int shift = (d->irq % 4) * 8;
|
|
unsigned int cpu = cpumask_first(mask_val);
|
|
u32 val, mask, bit;
|
|
|
|
if (cpu >= 8)
|
|
return -EINVAL;
|
|
|
|
mask = 0xff << shift;
|
|
bit = 1 << (cpu + shift);
|
|
|
|
spin_lock(&irq_controller_lock);
|
|
d->node = cpu;
|
|
val = readl_relaxed(reg) & ~mask;
|
|
writel_relaxed(val | bit, reg);
|
|
spin_unlock(&irq_controller_lock);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_PM
|
|
static int gic_set_wake(struct irq_data *d, unsigned int on)
|
|
{
|
|
int ret = -ENXIO;
|
|
|
|
if (gic_arch_extn.irq_set_wake)
|
|
ret = gic_arch_extn.irq_set_wake(d, on);
|
|
|
|
return ret;
|
|
}
|
|
|
|
#else
|
|
#define gic_set_wake NULL
|
|
#endif
|
|
|
|
static void gic_handle_cascade_irq(unsigned int irq, struct irq_desc *desc)
|
|
{
|
|
struct gic_chip_data *chip_data = irq_get_handler_data(irq);
|
|
struct irq_chip *chip = irq_get_chip(irq);
|
|
unsigned int cascade_irq, gic_irq;
|
|
unsigned long status;
|
|
|
|
chained_irq_enter(chip, desc);
|
|
|
|
spin_lock(&irq_controller_lock);
|
|
status = readl_relaxed(chip_data->cpu_base + GIC_CPU_INTACK);
|
|
spin_unlock(&irq_controller_lock);
|
|
|
|
gic_irq = (status & 0x3ff);
|
|
if (gic_irq == 1023)
|
|
goto out;
|
|
|
|
cascade_irq = gic_irq + chip_data->irq_offset;
|
|
if (unlikely(gic_irq < 32 || gic_irq > 1020 || cascade_irq >= NR_IRQS))
|
|
do_bad_IRQ(cascade_irq, desc);
|
|
else
|
|
generic_handle_irq(cascade_irq);
|
|
|
|
out:
|
|
chained_irq_exit(chip, desc);
|
|
}
|
|
|
|
static struct irq_chip gic_chip = {
|
|
.name = "GIC",
|
|
.irq_mask = gic_mask_irq,
|
|
.irq_unmask = gic_unmask_irq,
|
|
.irq_eoi = gic_eoi_irq,
|
|
.irq_set_type = gic_set_type,
|
|
.irq_retrigger = gic_retrigger,
|
|
#ifdef CONFIG_SMP
|
|
.irq_set_affinity = gic_set_affinity,
|
|
#endif
|
|
.irq_set_wake = gic_set_wake,
|
|
};
|
|
|
|
void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
|
|
{
|
|
if (gic_nr >= MAX_GIC_NR)
|
|
BUG();
|
|
if (irq_set_handler_data(irq, &gic_data[gic_nr]) != 0)
|
|
BUG();
|
|
irq_set_chained_handler(irq, gic_handle_cascade_irq);
|
|
}
|
|
|
|
static void __init gic_dist_init(struct gic_chip_data *gic,
|
|
unsigned int irq_start)
|
|
{
|
|
unsigned int gic_irqs, irq_limit, i;
|
|
void __iomem *base = gic->dist_base;
|
|
u32 cpumask = 1 << smp_processor_id();
|
|
|
|
cpumask |= cpumask << 8;
|
|
cpumask |= cpumask << 16;
|
|
|
|
writel_relaxed(0, base + GIC_DIST_CTRL);
|
|
|
|
/*
|
|
* Find out how many interrupts are supported.
|
|
* The GIC only supports up to 1020 interrupt sources.
|
|
*/
|
|
gic_irqs = readl_relaxed(base + GIC_DIST_CTR) & 0x1f;
|
|
gic_irqs = (gic_irqs + 1) * 32;
|
|
if (gic_irqs > 1020)
|
|
gic_irqs = 1020;
|
|
|
|
/*
|
|
* Set all global interrupts to be level triggered, active low.
|
|
*/
|
|
for (i = 32; i < gic_irqs; i += 16)
|
|
writel_relaxed(0, base + GIC_DIST_CONFIG + i * 4 / 16);
|
|
|
|
/*
|
|
* Set all global interrupts to this CPU only.
|
|
*/
|
|
for (i = 32; i < gic_irqs; i += 4)
|
|
writel_relaxed(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
|
|
|
|
/*
|
|
* Set priority on all global interrupts.
|
|
*/
|
|
for (i = 32; i < gic_irqs; i += 4)
|
|
writel_relaxed(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
|
|
|
|
/*
|
|
* Disable all interrupts. Leave the PPI and SGIs alone
|
|
* as these enables are banked registers.
|
|
*/
|
|
for (i = 32; i < gic_irqs; i += 32)
|
|
writel_relaxed(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
|
|
|
|
/*
|
|
* Limit number of interrupts registered to the platform maximum
|
|
*/
|
|
irq_limit = gic->irq_offset + gic_irqs;
|
|
if (WARN_ON(irq_limit > NR_IRQS))
|
|
irq_limit = NR_IRQS;
|
|
|
|
/*
|
|
* Setup the Linux IRQ subsystem.
|
|
*/
|
|
for (i = irq_start; i < irq_limit; i++) {
|
|
irq_set_chip_and_handler(i, &gic_chip, handle_fasteoi_irq);
|
|
irq_set_chip_data(i, gic);
|
|
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
|
|
}
|
|
|
|
writel_relaxed(1, base + GIC_DIST_CTRL);
|
|
}
|
|
|
|
static void __cpuinit gic_cpu_init(struct gic_chip_data *gic)
|
|
{
|
|
void __iomem *dist_base = gic->dist_base;
|
|
void __iomem *base = gic->cpu_base;
|
|
int i;
|
|
|
|
/*
|
|
* Deal with the banked PPI and SGI interrupts - disable all
|
|
* PPI interrupts, ensure all SGI interrupts are enabled.
|
|
*/
|
|
writel_relaxed(0xffff0000, dist_base + GIC_DIST_ENABLE_CLEAR);
|
|
writel_relaxed(0x0000ffff, dist_base + GIC_DIST_ENABLE_SET);
|
|
|
|
/*
|
|
* Set priority on PPI and SGI interrupts
|
|
*/
|
|
for (i = 0; i < 32; i += 4)
|
|
writel_relaxed(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4 / 4);
|
|
|
|
writel_relaxed(0xf0, base + GIC_CPU_PRIMASK);
|
|
writel_relaxed(1, base + GIC_CPU_CTRL);
|
|
}
|
|
|
|
void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
|
|
void __iomem *dist_base, void __iomem *cpu_base)
|
|
{
|
|
struct gic_chip_data *gic;
|
|
|
|
BUG_ON(gic_nr >= MAX_GIC_NR);
|
|
|
|
gic = &gic_data[gic_nr];
|
|
gic->dist_base = dist_base;
|
|
gic->cpu_base = cpu_base;
|
|
gic->irq_offset = (irq_start - 1) & ~31;
|
|
|
|
if (gic_nr == 0)
|
|
gic_cpu_base_addr = cpu_base;
|
|
|
|
gic_dist_init(gic, irq_start);
|
|
gic_cpu_init(gic);
|
|
}
|
|
|
|
void __cpuinit gic_secondary_init(unsigned int gic_nr)
|
|
{
|
|
BUG_ON(gic_nr >= MAX_GIC_NR);
|
|
|
|
gic_cpu_init(&gic_data[gic_nr]);
|
|
}
|
|
|
|
void __cpuinit gic_enable_ppi(unsigned int irq)
|
|
{
|
|
unsigned long flags;
|
|
|
|
local_irq_save(flags);
|
|
irq_set_status_flags(irq, IRQ_NOPROBE);
|
|
gic_unmask_irq(irq_get_irq_data(irq));
|
|
local_irq_restore(flags);
|
|
}
|
|
|
|
#ifdef CONFIG_SMP
|
|
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
|
|
{
|
|
unsigned long map = *cpus_addr(*mask);
|
|
|
|
/*
|
|
* Ensure that stores to Normal memory are visible to the
|
|
* other CPUs before issuing the IPI.
|
|
*/
|
|
dsb();
|
|
|
|
/* this always happens on GIC0 */
|
|
writel_relaxed(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT);
|
|
}
|
|
#endif
|