kernel_optimize_test/drivers/net/sky2.c
Stephen Hemminger 793b883ed1 [PATCH] sky2: driver update.
Here is revised patch against netdev sky2 branch.
It includes whitespace fixes, all the changes from the previous
review as well as some optimizations and timing fixes to
solve some of the hangs.

The stall problem is better but not perfect. It appears that
under stress the chip can't keep up with the bus
and sends a pause frame, then hangs. This version is for
testing, and hopefully other eyes might see the root
cause of the problem.

I don't want to reinvent the ugly watchdog code in the syskonnect
version of sk98lin.  If you read it you will see, the original
driver writer and the hardware developer obviously didn't
understand each other.

Dual port support is included, but not tested yet. It did
require small change to NAPI since both ports share same
IRQ.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-16 02:48:03 -04:00

2874 lines
76 KiB
C

/*
* New driver for Marvell Yukon 2 chipset.
* Based on earlier sk98lin, and skge driver.
*
* This driver intentionally does not support all the features
* of the original driver such as link fail-over and link management because
* those should be done at higher levels.
*
* Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
* TODO
* - coalescing setting?
* - vlan support
*
* TOTEST
* - variable ring size
* - speed setting
* - power management
* - netpoll
*/
#include <linux/config.h>
#include <linux/crc32.h>
#include <linux/kernel.h>
#include <linux/version.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/pci.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/in.h>
#include <linux/delay.h>
#include <asm/irq.h>
#include "sky2.h"
#define DRV_NAME "sky2"
#define DRV_VERSION "0.4"
#define PFX DRV_NAME " "
/*
* The Yukon II chipset takes 64 bit command blocks (called list elements)
* that are organized into three (receive, transmit, status) different rings
* similar to Tigon3. A transmit can require several elements;
* a receive requires one (or two if using 64 bit dma).
*/
#ifdef CONFIG_SKY2_EC_A1
#define is_ec_a1(hw) \
((hw)->chip_id == CHIP_ID_YUKON_EC && \
(hw)->chip_rev == CHIP_REV_YU_EC_A1)
#else
#define is_ec_a1(hw) 0
#endif
#define RX_LE_SIZE 256
#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
#define RX_MAX_PENDING (RX_LE_SIZE/2 - 1)
#define RX_DEF_PENDING 128
#define RX_COPY_THRESHOLD 128
#define TX_RING_SIZE 512
#define TX_DEF_PENDING (TX_RING_SIZE - 1)
#define TX_MIN_PENDING 64
#define MAX_SKB_TX_LE (4 + 2*MAX_SKB_FRAGS)
#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
#define ETH_JUMBO_MTU 9000
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
#define PHY_RETRIES 1000
static const u32 default_msg =
NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
| NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
| NETIF_MSG_IFUP | NETIF_MSG_IFDOWN | NETIF_MSG_INTR;
static int debug = -1; /* defaults above */
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
static const struct pci_device_id sky2_id_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, sky2_id_table);
/* Avoid conditionals by using array */
static const unsigned txqaddr[] = { Q_XA1, Q_XA2 };
static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
static const char *yukon_name[] = {
[CHIP_ID_YUKON_LITE - CHIP_ID_YUKON] = "Lite", /* 0xb0 */
[CHIP_ID_YUKON_LP - CHIP_ID_YUKON] = "LP", /* 0xb2 */
[CHIP_ID_YUKON_XL - CHIP_ID_YUKON] = "XL", /* 0xb3 */
[CHIP_ID_YUKON_EC - CHIP_ID_YUKON] = "EC", /* 0xb6 */
[CHIP_ID_YUKON_FE - CHIP_ID_YUKON] = "FE", /* 0xb7 */
};
/* Access to external PHY */
static void gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val)
{
int i;
gma_write16(hw, port, GM_SMI_DATA, val);
gma_write16(hw, port, GM_SMI_CTRL,
GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg));
for (i = 0; i < PHY_RETRIES; i++) {
if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
return;
udelay(1);
}
printk(KERN_WARNING PFX "%s: phy write timeout\n", hw->dev[port]->name);
}
static u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
{
int i;
gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV)
| GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
for (i = 0; i < PHY_RETRIES; i++) {
if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
goto ready;
udelay(1);
}
printk(KERN_WARNING PFX "%s: phy read timeout\n", hw->dev[port]->name);
ready:
return gma_read16(hw, port, GM_SMI_DATA);
}
static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
/* disable all GMAC IRQ's */
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
/* disable PHY IRQs */
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
gma_write16(hw, port, GM_MC_ADDR_H2, 0);
gma_write16(hw, port, GM_MC_ADDR_H3, 0);
gma_write16(hw, port, GM_MC_ADDR_H4, 0);
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA;
gma_write16(hw, port, GM_RX_CTRL, reg);
}
static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
{
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
PHY_M_EC_MAC_S_MSK);
ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
if (hw->chip_id == CHIP_ID_YUKON_EC)
ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA;
else
ectrl |= PHY_M_EC_M_DSC(2) | PHY_M_EC_S_DSC(3);
gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
}
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
if (hw->copper) {
if (hw->chip_id == CHIP_ID_YUKON_FE) {
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
} else {
/* disable energy detect */
ctrl &= ~PHY_M_PC_EN_DET_MSK;
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
if (sky2->autoneg == AUTONEG_ENABLE &&
hw->chip_id == CHIP_ID_YUKON_XL) {
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
}
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
} else {
/* workaround for deviation #4.88 (CRC errors) */
/* disable Automatic Crossover */
ctrl &= ~PHY_M_PC_MDIX_MSK;
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
/* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
ctrl &= ~PHY_M_MAC_MD_MSK;
ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
/* select page 1 to access Fiber registers */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
}
}
ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
if (sky2->autoneg == AUTONEG_DISABLE)
ctrl &= ~PHY_CT_ANE;
else
ctrl |= PHY_CT_ANE;
ctrl |= PHY_CT_RESET;
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
ctrl = 0;
ct1000 = 0;
adv = PHY_AN_CSMA;
if (sky2->autoneg == AUTONEG_ENABLE) {
if (hw->copper) {
if (sky2->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
ct1000 |= PHY_M_1000C_AHD;
if (sky2->advertising & ADVERTISED_100baseT_Full)
adv |= PHY_M_AN_100_FD;
if (sky2->advertising & ADVERTISED_100baseT_Half)
adv |= PHY_M_AN_100_HD;
if (sky2->advertising & ADVERTISED_10baseT_Full)
adv |= PHY_M_AN_10_FD;
if (sky2->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
} else /* special defines for FIBER (88E1011S only) */
adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
/* Set Flow-control capabilities */
if (sky2->tx_pause && sky2->rx_pause)
adv |= PHY_AN_PAUSE_CAP; /* symmetric */
else if (sky2->rx_pause && !sky2->tx_pause)
adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
else if (!sky2->rx_pause && sky2->tx_pause)
adv |= PHY_AN_PAUSE_ASYM; /* local */
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
} else {
/* forced speed/duplex settings */
ct1000 = PHY_M_1000C_MSE;
if (sky2->duplex == DUPLEX_FULL)
ctrl |= PHY_CT_DUP_MD;
switch (sky2->speed) {
case SPEED_1000:
ctrl |= PHY_CT_SP1000;
break;
case SPEED_100:
ctrl |= PHY_CT_SP100;
break;
}
ctrl |= PHY_CT_RESET;
}
if (hw->chip_id != CHIP_ID_YUKON_FE)
gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
/* Setup Phy LED's */
ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
ledover = 0;
switch (hw->chip_id) {
case CHIP_ID_YUKON_FE:
/* on 88E3082 these bits are at 11..9 (shifted left) */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR);
/* delete ACT LED control bits */
ctrl &= ~PHY_M_FELP_LED1_MSK;
/* change ACT LED control to blink mode */
ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL);
gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
break;
case CHIP_ID_YUKON_XL:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
/* select page 3 to access LED control register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
/* set LED Function Control register */
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
/* set Polarity Control register */
gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
(PHY_M_POLC_LS1_P_MIX(4) |
PHY_M_POLC_IS0_P_MIX(4) |
PHY_M_POLC_LOS_CTRL(2) |
PHY_M_POLC_INIT_CTRL(2) |
PHY_M_POLC_STA1_CTRL(2) |
PHY_M_POLC_STA0_CTRL(2)));
/* restore page register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
default:
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
/* turn off the Rx LED (LED_RX) */
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
if (ledover)
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
/* Enable phy interrupt on autonegotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
else
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
}
static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
{
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 reg;
int i;
const u8 *addr = hw->dev[port]->dev_addr;
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) {
/* WA DEV_472 -- looks like crossed wires on port 2 */
/* clear GMAC 1 Control reset */
sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR);
do {
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
} while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
}
if (sky2->autoneg == AUTONEG_DISABLE) {
reg = gma_read16(hw, port, GM_GP_CTRL);
reg |= GM_GPCR_AU_ALL_DIS;
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL);
switch (sky2->speed) {
case SPEED_1000:
reg |= GM_GPCR_SPEED_1000;
/* fallthru */
case SPEED_100:
reg |= GM_GPCR_SPEED_100;
}
if (sky2->duplex == DUPLEX_FULL)
reg |= GM_GPCR_DUP_FULL;
} else
reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
if (!sky2->tx_pause && !sky2->rx_pause) {
sky2_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
reg |=
GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
} else if (sky2->tx_pause && !sky2->rx_pause) {
/* disable Rx flow-control */
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
}
gma_write16(hw, port, GM_GP_CTRL, reg);
sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
spin_lock_bh(&hw->phy_lock);
sky2_phy_init(hw, port);
spin_unlock_bh(&hw->phy_lock);
/* MIB clear */
reg = gma_read16(hw, port, GM_PHY_ADDR);
gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
for (i = 0; i < GM_MIB_CNT_SIZE; i++)
gma_read16(hw, port, GM_MIB_CNT_BASE + 8 * i);
gma_write16(hw, port, GM_PHY_ADDR, reg);
/* transmit control */
gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
/* receive control reg: unicast + multicast + no FCS */
gma_write16(hw, port, GM_RX_CTRL,
GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
/* transmit flow control */
gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
/* transmit parameter */
gma_write16(hw, port, GM_TX_PARAM,
TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) |
TX_BACK_OFF_LIM(TX_BOF_LIM_DEF));
/* serial mode register */
reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
if (hw->dev[port]->mtu > 1500)
reg |= GM_SMOD_JUMBO_ENA;
gma_write16(hw, port, GM_SERIAL_MODE, reg);
/* virtual address for data */
gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
/* physical address: used for pause frames */
gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
/* ignore counter overflows */
gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
/* Configure Rx MAC FIFO */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, RX_GMF_CTRL_T),
GMF_OPER_ON | GMF_RX_F_FL_ON);
/* Flush Rx MAC FIFO on any flowcontrol or error */
reg = GMR_FS_ANY_ERR;
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev <= 1)
reg = 0; /* WA Dev #4115 */
sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), reg);
/* Set threshold to 0xa (64 bytes)
* ASF disabled so no need to do WA dev #4.30
*/
sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
/* Configure Tx MAC FIFO */
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
}
static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, size_t len)
{
u32 end;
start /= 8;
len /= 8;
end = start + len - 1;
pr_debug("sky2_ramset start=%d end=%d\n", start, end);
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
sky2_write32(hw, RB_ADDR(q, RB_START), start);
sky2_write32(hw, RB_ADDR(q, RB_END), end);
sky2_write32(hw, RB_ADDR(q, RB_WP), start);
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
if (q == Q_R1 || q == Q_R2) {
u32 rxup, rxlo;
rxlo = len/2;
rxup = rxlo + len/4;
pr_debug(" utpp=%d ltpp=%d\n", rxup, rxlo);
/* Set thresholds on receive queue's */
sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), rxup);
sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), rxlo);
} else {
/* Enable store & forward on Tx queue's because
* Tx FIFO is only 1K on Yukon
*/
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
}
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
sky2_read8(hw, RB_ADDR(q, RB_CTRL));
}
/* Setup Bus Memory Interface */
static void sky2_qset(struct sky2_hw *hw, u16 q, u32 wm)
{
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET);
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT);
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON);
sky2_write32(hw, Q_ADDR(q, Q_WM), wm);
}
/* Setup prefetch unit registers. This is the interface between
* hardware and driver list elements
*/
static inline void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr,
u64 addr, u32 last)
{
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), addr >> 32);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), (u32) addr);
sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON);
sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL));
}
static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2)
{
struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod;
sky2->tx_prod = (sky2->tx_prod + 1) % TX_RING_SIZE;
return le;
}
/*
* This is a workaround code taken from syskonnect sk98lin driver
* to deal with chip bug on Yukon EC rev 0 in the wraparound case.
*/
static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q,
u16 idx, u16 *last, u16 size)
{
if (is_ec_a1(hw) && idx < *last) {
u16 hwget = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX));
if (hwget == 0) {
/* Start prefetching again */
sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 0xe0);
goto setnew;
}
if (hwget == size - 1) {
/* set watermark to one list element */
sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 8);
/* set put index to first list element */
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), 0);
} else /* have hardware go to end of list */
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX),
size - 1);
} else {
setnew:
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
}
*last = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX));
}
static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2)
{
struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
sky2->rx_put = (sky2->rx_put + 1) % RX_LE_SIZE;
return le;
}
/* Build description to hardware about buffer */
static inline void sky2_rx_add(struct sky2_port *sky2, struct ring_info *re)
{
struct sky2_rx_le *le;
u32 hi = (re->mapaddr >> 16) >> 16;
re->idx = sky2->rx_put;
if (sky2->rx_addr64 != hi) {
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32(hi);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->rx_addr64 = hi;
}
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32((u32) re->mapaddr);
le->length = cpu_to_le16(re->maplen);
le->ctrl = 0;
le->opcode = OP_PACKET | HW_OWNER;
}
/* Tell receiver about new buffers. */
static inline void rx_set_put(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
if (sky2->rx_last_put != sky2->rx_put)
sky2_put_idx(sky2->hw, rxqaddr[sky2->port], sky2->rx_put,
&sky2->rx_last_put, RX_LE_SIZE);
}
/* Tell chip where to start receive checksum.
* Actually has two checksums, but set both same to avoid possible byte
* order problems.
*/
static void rx_set_checksum(struct sky2_port *sky2)
{
struct sky2_rx_le *le;
le = sky2_next_rx(sky2);
le->addr = (ETH_HLEN << 16) | ETH_HLEN;
le->ctrl = 0;
le->opcode = OP_TCPSTART | HW_OWNER;
sky2_write16(sky2->hw, Y2_QADDR(rxqaddr[sky2->port],
PREF_UNIT_PUT_IDX), sky2->rx_put);
sky2_read16(sky2->hw, Y2_QADDR(rxqaddr[sky2->port], PREF_UNIT_PUT_IDX));
mdelay(1);
sky2_write32(sky2->hw,
Q_ADDR(rxqaddr[sky2->port], Q_CSR),
sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
}
/* Cleanout receive buffer area, assumes receiver hardware stopped */
static void sky2_rx_clean(struct sky2_port *sky2)
{
unsigned i;
memset(sky2->rx_le, 0, RX_LE_BYTES);
for (i = 0; i < sky2->rx_pending; i++) {
struct ring_info *re = sky2->rx_ring + i;
if (re->skb) {
pci_unmap_single(sky2->hw->pdev,
re->mapaddr, re->maplen,
PCI_DMA_FROMDEVICE);
kfree_skb(re->skb);
re->skb = NULL;
}
}
}
static inline struct sk_buff *sky2_rx_alloc(struct sky2_port *sky2,
unsigned int size,
unsigned int gfp_mask)
{
struct sk_buff *skb;
skb = alloc_skb(size + NET_IP_ALIGN, gfp_mask);
if (likely(skb)) {
skb->dev = sky2->netdev;
skb_reserve(skb, NET_IP_ALIGN);
}
return skb;
}
/*
* Allocate and setup receiver buffer pool.
* In case of 64 bit dma, there are 2X as many list elements
* available as ring entries
* and need to reserve one list element so we don't wrap around.
*/
static int sky2_rx_fill(struct sky2_port *sky2)
{
unsigned i;
const unsigned rx_buf_size = sky2->netdev->mtu + ETH_HLEN + 8;
for (i = 0; i < sky2->rx_pending; i++) {
struct ring_info *re = sky2->rx_ring + i;
re->skb = sky2_rx_alloc(sky2, rx_buf_size, GFP_KERNEL);
if (!re->skb)
goto nomem;
re->mapaddr = pci_map_single(sky2->hw->pdev, re->skb->data,
rx_buf_size, PCI_DMA_FROMDEVICE);
re->maplen = rx_buf_size;
sky2_rx_add(sky2, re);
}
return 0;
nomem:
sky2_rx_clean(sky2);
return -ENOMEM;
}
/* Bring up network interface. */
static int sky2_up(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u32 ramsize, rxspace;
int err = -ENOMEM;
if (netif_msg_ifup(sky2))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
/* must be power of 2 */
sky2->tx_le = pci_alloc_consistent(hw->pdev,
TX_RING_SIZE *
sizeof(struct sky2_tx_le),
&sky2->tx_le_map);
if (!sky2->tx_le)
goto err_out;
sky2->tx_ring = kmalloc(TX_RING_SIZE * sizeof(struct ring_info),
GFP_KERNEL);
if (!sky2->tx_ring)
goto err_out;
sky2->tx_prod = sky2->tx_cons = 0;
memset(sky2->tx_ring, 0, TX_RING_SIZE * sizeof(struct ring_info));
sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES,
&sky2->rx_le_map);
if (!sky2->rx_le)
goto err_out;
memset(sky2->rx_le, 0, RX_LE_BYTES);
sky2->rx_ring = kmalloc(sky2->rx_pending * sizeof(struct ring_info),
GFP_KERNEL);
if (!sky2->rx_ring)
goto err_out;
sky2_mac_init(hw, port);
/* Configure RAM buffers */
if (hw->chip_id == CHIP_ID_YUKON_FE ||
(hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == 2))
ramsize = 4096;
else {
u8 e0 = sky2_read8(hw, B2_E_0);
ramsize = (e0 == 0) ? (128 * 1024) : (e0 * 4096);
}
/* 2/3 for Rx */
rxspace = (2 * ramsize) / 3;
sky2_ramset(hw, rxqaddr[port], 0, rxspace);
sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
/* Make sure SyncQ is disabled */
sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
RB_RST_SET);
sky2_qset(hw, rxqaddr[port], is_pciex(hw) ? 0x80 : 0x600);
sky2_qset(hw, txqaddr[port], 0x600);
sky2->rx_put = sky2->rx_next = 0;
sky2_prefetch_init(hw, rxqaddr[port], sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
err = sky2_rx_fill(sky2);
if (err)
goto err_out;
/* Give buffers to receiver */
sky2_write16(sky2->hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_PUT_IDX),
sky2->rx_put);
sky2->rx_last_put = sky2_read16(sky2->hw,
Y2_QADDR(rxqaddr[port],
PREF_UNIT_PUT_IDX));
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
TX_RING_SIZE - 1);
/* Enable interrupts from phy/mac for port */
hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
return 0;
err_out:
if (sky2->rx_le)
pci_free_consistent(hw->pdev, RX_LE_BYTES,
sky2->rx_le, sky2->rx_le_map);
if (sky2->tx_le)
pci_free_consistent(hw->pdev,
TX_RING_SIZE * sizeof(struct sky2_tx_le),
sky2->tx_le, sky2->tx_le_map);
if (sky2->tx_ring)
kfree(sky2->tx_ring);
if (sky2->rx_ring)
kfree(sky2->rx_ring);
return err;
}
/* Modular subtraction in ring */
static inline int tx_dist(unsigned tail, unsigned head)
{
return (head >= tail ? head : head + TX_RING_SIZE) - tail;
}
/* Number of list elements available for next tx */
static inline int tx_avail(const struct sky2_port *sky2)
{
return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod);
}
/* Estimate of number of transmit list elements required */
static inline unsigned tx_le_req(const struct sk_buff *skb)
{
unsigned count;
count = sizeof(dma_addr_t) / sizeof(u32);
count += skb_shinfo(skb)->nr_frags * count;
if (skb_shinfo(skb)->tso_size)
++count;
if (skb->ip_summed)
++count;
return count;
}
/*
* Put one packet in ring for transmit.
* A single packet can generate multiple list elements, and
* the number of ring elements will probably be less than the number
* of list elements used.
*/
static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
struct sky2_tx_le *le;
struct ring_info *re;
unsigned long flags;
unsigned i, len;
dma_addr_t mapping;
u32 addr64;
u16 mss;
u8 ctrl;
local_irq_save(flags);
if (!spin_trylock(&sky2->tx_lock)) {
local_irq_restore(flags);
return NETDEV_TX_LOCKED;
}
if (unlikely(tx_avail(sky2) < tx_le_req(skb))) {
netif_stop_queue(dev);
spin_unlock_irqrestore(&sky2->tx_lock, flags);
printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
dev->name);
return NETDEV_TX_BUSY;
}
if (unlikely(netif_msg_tx_queued(sky2)))
printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
dev->name, sky2->tx_prod, skb->len);
len = skb_headlen(skb);
mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
addr64 = (mapping >> 16) >> 16;
re = sky2->tx_ring + sky2->tx_prod;
/* Send high bits if changed */
if (addr64 != sky2->tx_addr64) {
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32(addr64);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = addr64;
}
/* Check for TCP Segmentation Offload */
mss = skb_shinfo(skb)->tso_size;
if (mss != 0) {
/* just drop the packet if non-linear expansion fails */
if (skb_header_cloned(skb) &&
pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
dev_kfree_skb_any(skb);
goto out_unlock;
}
mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
mss += ETH_HLEN;
}
if (mss != sky2->tx_last_mss) {
le = get_tx_le(sky2);
le->tx.tso.size = cpu_to_le16(mss);
le->tx.tso.rsvd = 0;
le->opcode = OP_LRGLEN | HW_OWNER;
le->ctrl = 0;
sky2->tx_last_mss = mss;
}
/* Handle TCP checksum offload */
ctrl = 0;
if (skb->ip_summed == CHECKSUM_HW) {
u16 hdr = skb->h.raw - skb->data;
u16 offset = hdr + skb->csum;
ctrl = CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
if (skb->nh.iph->protocol == IPPROTO_UDP)
ctrl |= UDPTCP;
le = get_tx_le(sky2);
le->tx.csum.start = cpu_to_le16(hdr);
le->tx.csum.offset = cpu_to_le16(offset);
le->length = 0; /* initial checksum value */
le->ctrl = 1; /* one packet */
le->opcode = OP_TCPLISW | HW_OWNER;
}
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(len);
le->ctrl = ctrl;
le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
/* Record the transmit mapping info */
re->skb = skb;
re->mapaddr = mapping;
re->maplen = len;
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
struct ring_info *fre;
mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
frag->size, PCI_DMA_TODEVICE);
addr64 = (mapping >> 16) >> 16;
if (addr64 != sky2->tx_addr64) {
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32(addr64);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = addr64;
}
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(frag->size);
le->ctrl = ctrl;
le->opcode = OP_BUFFER | HW_OWNER;
fre = sky2->tx_ring
+ ((re - sky2->tx_ring) + i + 1) % TX_RING_SIZE;
fre->skb = NULL;
fre->mapaddr = mapping;
fre->maplen = frag->size;
}
re->idx = sky2->tx_prod;
le->ctrl |= EOP;
sky2_put_idx(sky2->hw, txqaddr[sky2->port], sky2->tx_prod,
&sky2->tx_last_put, TX_RING_SIZE);
if (tx_avail(sky2) < MAX_SKB_TX_LE + 1)
netif_stop_queue(dev);
out_unlock:
mmiowb();
spin_unlock_irqrestore(&sky2->tx_lock, flags);
dev->trans_start = jiffies;
return NETDEV_TX_OK;
}
/*
* Free ring elements from starting at tx_cons until "done"
*
* NB: the hardware will tell us about partial completion of multi-part
* buffers; these are defered until completion.
*/
static void sky2_tx_complete(struct net_device *dev, u16 done)
{
struct sky2_port *sky2 = netdev_priv(dev);
unsigned i;
if (netif_msg_tx_done(sky2))
printk(KERN_DEBUG "%s: tx done, upto %u\n", dev->name, done);
spin_lock(&sky2->tx_lock);
while (sky2->tx_cons != done) {
struct ring_info *re = sky2->tx_ring + sky2->tx_cons;
struct sk_buff *skb;
/* Check for partial status */
if (tx_dist(sky2->tx_cons, done)
< tx_dist(sky2->tx_cons, re->idx))
goto out;
skb = re->skb;
pci_unmap_single(sky2->hw->pdev,
re->mapaddr, re->maplen, PCI_DMA_TODEVICE);
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
struct ring_info *fre;
fre =
sky2->tx_ring + (sky2->tx_cons + i +
1) % TX_RING_SIZE;
pci_unmap_page(sky2->hw->pdev, fre->mapaddr,
fre->maplen, PCI_DMA_TODEVICE);
}
dev_kfree_skb_any(skb);
sky2->tx_cons = re->idx;
}
out:
if (netif_queue_stopped(dev) && tx_avail(sky2) > MAX_SKB_TX_LE)
netif_wake_queue(dev);
spin_unlock(&sky2->tx_lock);
}
/* Cleanup all untransmitted buffers, assume transmitter not running */
static inline void sky2_tx_clean(struct sky2_port *sky2)
{
sky2_tx_complete(sky2->netdev, sky2->tx_prod);
}
/* Network shutdown */
static int sky2_down(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 ctrl;
int i;
if (netif_msg_ifdown(sky2))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
netif_stop_queue(dev);
sky2_phy_reset(hw, port);
/* Stop transmitter */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR));
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
RB_RST_SET | RB_DIS_OP_MD);
ctrl = gma_read16(hw, port, GM_GP_CTRL);
ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
gma_write16(hw, port, GM_GP_CTRL, ctrl);
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
&& port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
/* Disable Force Sync bit and Enable Alloc bit */
sky2_write8(hw, SK_REG(port, TXA_CTRL),
TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
/* Stop Interval Timer and Limit Counter of Tx Arbiter */
sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
/* Reset the PCI FIFO of the async Tx queue */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR),
BMU_RST_SET | BMU_FIFO_RST);
/* Reset the Tx prefetch units */
sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL),
PREF_UNIT_RST_SET);
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
/*
* The RX Stop command will not work for Yukon-2 if the BMU does not
* reach the end of packet and since we can't make sure that we have
* incoming data, we must reset the BMU while it is not doing a DMA
* transfer. Since it is possible that the RX path is still active,
* the RX RAM buffer will be stopped first, so any possible incoming
* data will not trigger a DMA. After the RAM buffer is stopped, the
* BMU is polled until any DMA in progress is ended and only then it
* will be reset.
*/
/* disable the RAM Buffer receive queue */
sky2_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_DIS_OP_MD);
for (i = 0; i < 0xffff; i++)
if (sky2_read8(hw, RB_ADDR(rxqaddr[port], Q_RSL))
== sky2_read8(hw, RB_ADDR(rxqaddr[port], Q_RL)))
break;
sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR),
BMU_RST_SET | BMU_FIFO_RST);
/* reset the Rx prefetch unit */
sky2_write32(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_CTRL),
PREF_UNIT_RST_SET);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
/* turn off led's */
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
sky2_tx_clean(sky2);
sky2_rx_clean(sky2);
pci_free_consistent(hw->pdev, RX_LE_BYTES,
sky2->rx_le, sky2->rx_le_map);
kfree(sky2->rx_ring);
pci_free_consistent(hw->pdev,
TX_RING_SIZE * sizeof(struct sky2_tx_le),
sky2->tx_le, sky2->tx_le_map);
kfree(sky2->tx_ring);
return 0;
}
static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
{
if (!hw->copper)
return SPEED_1000;
if (hw->chip_id == CHIP_ID_YUKON_FE)
return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
switch (aux & PHY_M_PS_SPEED_MSK) {
case PHY_M_PS_SPEED_1000:
return SPEED_1000;
case PHY_M_PS_SPEED_100:
return SPEED_100;
default:
return SPEED_10;
}
}
static void sky2_link_up(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 reg;
/* disable Rx GMAC FIFO flush mode */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RX_F_FL_OFF);
/* Enable Transmit FIFO Underrun */
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_DUP_FULL;
/* enable Rx/Tx */
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL);
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
netif_carrier_on(sky2->netdev);
netif_wake_queue(sky2->netdev);
/* Turn on link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
PHY_M_LEDC_INIT_CTRL(sky2->speed ==
SPEED_10 ? 7 : 0) |
PHY_M_LEDC_STA1_CTRL(sky2->speed ==
SPEED_100 ? 7 : 0) |
PHY_M_LEDC_STA0_CTRL(sky2->speed ==
SPEED_1000 ? 7 : 0));
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
if (netif_msg_link(sky2))
printk(KERN_INFO PFX
"%s: Link is up at %d Mbps, %s duplex, flowcontrol %s\n",
sky2->netdev->name, sky2->speed,
sky2->duplex == DUPLEX_FULL ? "full" : "half",
(sky2->tx_pause && sky2->rx_pause) ? "both" :
sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
}
static void sky2_link_down(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 reg;
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
reg = gma_read16(hw, port, GM_GP_CTRL);
reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL); /* PCI post */
if (sky2->rx_pause && !sky2->tx_pause) {
/* restore Asymmetric Pause bit */
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
| PHY_M_AN_ASP);
}
sky2_phy_reset(hw, port);
netif_carrier_off(sky2->netdev);
netif_stop_queue(sky2->netdev);
/* Turn on link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
if (netif_msg_link(sky2))
printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
sky2_phy_init(hw, port);
}
static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 lpa;
lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
if (lpa & PHY_M_AN_RF) {
printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
return -1;
}
if (hw->chip_id != CHIP_ID_YUKON_FE &&
gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
printk(KERN_ERR PFX "%s: master/slave fault",
sky2->netdev->name);
return -1;
}
if (!(aux & PHY_M_PS_SPDUP_RES)) {
printk(KERN_ERR PFX "%s: speed/duplex mismatch",
sky2->netdev->name);
return -1;
}
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
sky2->speed = sky2_phy_speed(hw, aux);
/* Pause bits are offset (9..8) */
if (hw->chip_id == CHIP_ID_YUKON_XL)
aux >>= 6;
sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
if ((sky2->tx_pause || sky2->rx_pause)
&& !(sky2->speed < SPEED_1000 && sky2->duplex == DUPLEX_HALF))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
else
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
return 0;
}
/*
* Interrrupt from PHY are handled in tasklet (soft irq)
* because accessing phy registers requires spin wait which might
* cause excess interrupt latency.
*/
static void sky2_phy_task(unsigned long data)
{
struct sky2_port *sky2 = (struct sky2_port *)data;
struct sky2_hw *hw = sky2->hw;
u16 istatus, phystat;
spin_lock(&hw->phy_lock);
istatus = gm_phy_read(hw, sky2->port, PHY_MARV_INT_STAT);
phystat = gm_phy_read(hw, sky2->port, PHY_MARV_PHY_STAT);
if (netif_msg_intr(sky2))
printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
sky2->netdev->name, istatus, phystat);
if (istatus & PHY_M_IS_AN_COMPL) {
if (sky2_autoneg_done(sky2, phystat) == 0)
sky2_link_up(sky2);
goto out;
}
if (istatus & PHY_M_IS_LSP_CHANGE)
sky2->speed = sky2_phy_speed(hw, phystat);
if (istatus & PHY_M_IS_DUP_CHANGE)
sky2->duplex =
(phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
if (istatus & PHY_M_IS_LST_CHANGE) {
if (phystat & PHY_M_PS_LINK_UP)
sky2_link_up(sky2);
else
sky2_link_down(sky2);
}
out:
spin_unlock(&hw->phy_lock);
local_irq_disable();
hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
local_irq_enable();
}
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
sky2_write32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR), BMU_STOP);
sky2_read32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR));
sky2_tx_clean(sky2);
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
{
int err = 0;
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
if (netif_running(dev))
sky2_down(dev);
dev->mtu = new_mtu;
if (netif_running(dev))
err = sky2_up(dev);
return err;
}
/*
* Receive one packet.
* For small packets or errors, just reuse existing skb.
* For larger pakects, get new buffer.
*/
static struct sk_buff *sky2_receive(struct sky2_hw *hw, unsigned port,
u16 length, u32 status)
{
struct net_device *dev = hw->dev[port];
struct sky2_port *sky2 = netdev_priv(dev);
struct ring_info *re = sky2->rx_ring + sky2->rx_next;
struct sk_buff *skb, *nskb;
const unsigned int rx_buf_size = dev->mtu + ETH_HLEN + 8;
if (unlikely(netif_msg_rx_status(sky2)))
printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
dev->name, sky2->rx_next, status, length);
sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
skb = NULL;
if (!(status & GMR_FS_RX_OK)
|| (status & GMR_FS_ANY_ERR)
|| (length << 16) != (status & GMR_FS_LEN)
|| length > rx_buf_size)
goto error;
if (length < RX_COPY_THRESHOLD) {
nskb = sky2_rx_alloc(sky2, length, GFP_ATOMIC);
if (!nskb)
goto resubmit;
pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->mapaddr,
length, PCI_DMA_FROMDEVICE);
memcpy(nskb->data, re->skb->data, length);
pci_dma_sync_single_for_device(sky2->hw->pdev, re->mapaddr,
length, PCI_DMA_FROMDEVICE);
skb = nskb;
} else {
nskb = sky2_rx_alloc(sky2, rx_buf_size, GFP_ATOMIC);
if (!nskb)
goto resubmit;
skb = re->skb;
pci_unmap_single(sky2->hw->pdev, re->mapaddr,
re->maplen, PCI_DMA_FROMDEVICE);
prefetch(skb->data);
re->skb = nskb;
re->mapaddr = pci_map_single(sky2->hw->pdev, nskb->data,
rx_buf_size, PCI_DMA_FROMDEVICE);
re->maplen = rx_buf_size;
}
resubmit:
BUG_ON(re->skb == skb);
sky2_rx_add(sky2, re);
return skb;
error:
if (status & GMR_FS_GOOD_FC)
goto resubmit;
if (netif_msg_rx_err(sky2))
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
sky2->netdev->name, status, length);
if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
sky2->net_stats.rx_length_errors++;
if (status & GMR_FS_FRAGMENT)
sky2->net_stats.rx_frame_errors++;
if (status & GMR_FS_CRC_ERR)
sky2->net_stats.rx_crc_errors++;
if (status & GMR_FS_RX_FF_OV)
sky2->net_stats.rx_fifo_errors++;
goto resubmit;
}
/* Transmit ring index in reported status block is encoded as:
*
* | TXS2 | TXA2 | TXS1 | TXA1
*/
static inline u16 tx_index(u8 port, u32 status, u16 len)
{
if (port == 0)
return status & 0xfff;
else
return ((status >> 24) & 0xff) | (len & 0xf) << 8;
}
/*
* Both ports share the same status interrupt, therefore there is only
* one poll routine.
*/
static int sky2_poll(struct net_device *dev, int *budget)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned int to_do = min(dev->quota, *budget);
unsigned int work_done = 0;
u16 hwidx;
unsigned char summed[2] = { CHECKSUM_NONE, CHECKSUM_NONE };
unsigned int csum[2];
hwidx = sky2_read16(hw, STAT_PUT_IDX);
rmb();
while (hw->st_idx != hwidx && work_done < to_do) {
struct sky2_status_le *le = hw->st_le + hw->st_idx;
struct sk_buff *skb;
u8 port;
u32 status;
u16 length;
status = le32_to_cpu(le->status);
length = le16_to_cpu(le->length);
port = le->link;
BUG_ON(port >= hw->ports || hw->dev[port] == NULL);
switch (le->opcode & ~HW_OWNER) {
case OP_RXSTAT:
skb = sky2_receive(hw, port, length, status);
if (likely(skb)) {
__skb_put(skb, length);
skb->protocol = eth_type_trans(skb, dev);
/* Add hw checksum if available */
skb->ip_summed = summed[port];
skb->csum = csum[port];
/* Clear for next packet */
csum[port] = 0;
summed[port] = CHECKSUM_NONE;
netif_receive_skb(skb);
dev->last_rx = jiffies;
++work_done;
}
break;
case OP_RXCHKS:
/* Save computed checksum for next rx */
csum[port] = le16_to_cpu(status & 0xffff);
summed[port] = CHECKSUM_HW;
break;
case OP_TXINDEXLE:
sky2_tx_complete(hw->dev[port],
tx_index(port, status, length));
break;
case OP_RXTIMESTAMP:
break;
default:
if (net_ratelimit())
printk(KERN_WARNING PFX
"unknown status opcode 0x%x\n",
le->opcode);
break;
}
hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE;
if (hw->st_idx == hwidx) {
hwidx = sky2_read16(hw, STAT_PUT_IDX);
rmb();
}
}
mmiowb();
if (hw->dev[0])
rx_set_put(hw->dev[0]);
if (hw->dev[1])
rx_set_put(hw->dev[1]);
*budget -= work_done;
dev->quota -= work_done;
if (work_done < to_do) {
/*
* Another chip workaround, need to restart TX timer if status
* LE was handled. WA_DEV_43_418
*/
if (is_ec_a1(hw)) {
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
}
hw->intr_mask |= Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
sky2_read32(hw, B0_IMSK);
netif_rx_complete(dev);
}
return work_done >= to_do;
}
static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status)
{
struct net_device *dev = hw->dev[port];
printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
dev->name, status);
if (status & Y2_IS_PAR_RD1) {
printk(KERN_ERR PFX "%s: ram data read parity error\n",
dev->name);
/* Clear IRQ */
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
}
if (status & Y2_IS_PAR_WR1) {
printk(KERN_ERR PFX "%s: ram data write parity error\n",
dev->name);
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
}
if (status & Y2_IS_PAR_MAC1) {
printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
}
if (status & Y2_IS_PAR_RX1) {
printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
}
if (status & Y2_IS_TCP_TXA1) {
printk(KERN_ERR PFX "%s: TCP segmentation error\n", dev->name);
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
}
}
static void sky2_hw_intr(struct sky2_hw *hw)
{
u32 status = sky2_read32(hw, B0_HWE_ISRC);
if (status & Y2_IS_TIST_OV)
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
u16 pci_err;
pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
pci_name(hw->pdev), pci_err);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
if (status & Y2_IS_PCI_EXP) {
/* PCI-Express uncorrectable Error occured */
u32 pex_err;
pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
pci_name(hw->pdev), pex_err);
/* clear the interrupt */
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
0xffffffffUL);
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
if (pex_err & PEX_FATAL_ERRORS) {
u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
hwmsk &= ~Y2_IS_PCI_EXP;
sky2_write32(hw, B0_HWE_IMSK, hwmsk);
}
}
if (status & Y2_HWE_L1_MASK)
sky2_hw_error(hw, 0, status);
status >>= 8;
if (status & Y2_HWE_L1_MASK)
sky2_hw_error(hw, 1, status);
}
static void sky2_mac_intr(struct sky2_hw *hw, unsigned port)
{
struct net_device *dev = hw->dev[port];
struct sky2_port *sky2 = netdev_priv(dev);
u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
if (netif_msg_intr(sky2))
printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n",
dev->name, status);
if (status & GM_IS_RX_FF_OR) {
++sky2->net_stats.rx_fifo_errors;
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
}
if (status & GM_IS_TX_FF_UR) {
++sky2->net_stats.tx_fifo_errors;
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
}
}
static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
{
struct net_device *dev = hw->dev[port];
struct sky2_port *sky2 = netdev_priv(dev);
hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
tasklet_schedule(&sky2->phy_task);
}
static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
{
struct sky2_hw *hw = dev_id;
u32 status;
status = sky2_read32(hw, B0_Y2_SP_ISRC2);
if (status == 0 || status == ~0)
return IRQ_NONE;
if (status & Y2_IS_HW_ERR)
sky2_hw_intr(hw);
/* Do NAPI for Rx and Tx status */
if ((status & Y2_IS_STAT_BMU) && netif_rx_schedule_test(hw->dev[0])) {
sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
hw->intr_mask &= ~Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
__netif_rx_schedule(hw->dev[0]);
}
if (status & Y2_IS_IRQ_PHY1)
sky2_phy_intr(hw, 0);
if (status & Y2_IS_IRQ_PHY2)
sky2_phy_intr(hw, 1);
if (status & Y2_IS_IRQ_MAC1)
sky2_mac_intr(hw, 0);
if (status & Y2_IS_IRQ_MAC2)
sky2_mac_intr(hw, 1);
sky2_write32(hw, B0_Y2_SP_ICR, 2);
sky2_read32(hw, B0_IMSK);
return IRQ_HANDLED;
}
#ifdef CONFIG_NET_POLL_CONTROLLER
static void sky2_netpoll(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2_intr(sky2->hw->pdev->irq, sky2->hw, NULL);
}
#endif
/* Chip internal frequency for clock calculations */
static inline u32 sky2_khz(const struct sky2_hw *hw)
{
switch (hw->chip_id) {
case CHIP_ID_YUKON_EC:
return 125000; /* 125 Mhz */
case CHIP_ID_YUKON_FE:
return 100000; /* 100 Mhz */
default: /* YUKON_XL */
return 156000; /* 156 Mhz */
}
}
static inline u32 sky2_ms2clk(const struct sky2_hw *hw, u32 ms)
{
return sky2_khz(hw) * ms;
}
static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us)
{
return (sky2_khz(hw) * us) / 1000;
}
static int sky2_reset(struct sky2_hw *hw)
{
u32 ctst, power;
u16 status;
u8 t8, pmd_type;
int i;
ctst = sky2_read32(hw, B0_CTST);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
pci_name(hw->pdev), hw->chip_id);
return -EOPNOTSUPP;
}
/* ring for status responses */
hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
&hw->st_dma);
if (!hw->st_le)
return -ENOMEM;
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
}
/* do a SW reset */
sky2_write8(hw, B0_CTST, CS_RST_SET);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
/* clear PCI errors, if any */
pci_read_config_word(hw->pdev, PCI_STATUS, &status);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PCI_STATUS,
status | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B0_CTST, CS_MRST_CLR);
/* clear any PEX errors */
if (is_pciex(hw)) {
u16 lstat;
pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
0xffffffffUL);
pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat);
}
pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC))
++hw->ports;
}
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
/* switch power to VCC (WA for VAUX problem) */
sky2_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
/* disable Core Clock Division, */
sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
/* enable bits are inverted */
sky2_write8(hw, B2_Y2_CLK_GATE,
Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
/* Turn off phy power saving */
pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &power);
power &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
/* looks like this xl is back asswards .. */
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
power |= PCI_Y2_PHY1_COMA;
if (hw->ports > 1)
power |= PCI_Y2_PHY2_COMA;
}
pci_write_config_dword(hw->pdev, PCI_DEV_REG1, power);
for (i = 0; i < hw->ports; i++) {
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
}
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
/* Clear I2C IRQ noise */
sky2_write32(hw, B2_I2C_IRQ, 1);
/* turn off hardware timer (unused) */
sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
sky2_write8(hw, B0_Y2LED, LED_STAT_ON);
/* Turn on descriptor polling (every 75us) */
sky2_write32(hw, B28_DPT_INI, sky2_us2clk(hw, 75));
sky2_write8(hw, B28_DPT_CTRL, DPT_START);
/* Turn off receive timestamp */
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP);
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
/* enable the Tx Arbiters */
for (i = 0; i < hw->ports; i++)
sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
/* Initialize ram interface */
for (i = 0; i < hw->ports; i++) {
sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53);
}
if (is_pciex(hw)) {
u16 pctrl;
/* change Max. Read Request Size to 2048 bytes */
pci_read_config_word(hw->pdev, PEX_DEV_CTRL, &pctrl);
pctrl &= ~PEX_DC_MAX_RRS_MSK;
pctrl |= PEX_DC_MAX_RD_RQ_SIZE(4);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PEX_DEV_CTRL, pctrl);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
spin_lock_bh(&hw->phy_lock);
for (i = 0; i < hw->ports; i++)
sky2_phy_reset(hw, i);
spin_unlock_bh(&hw->phy_lock);
memset(hw->st_le, 0, STATUS_LE_BYTES);
hw->st_idx = 0;
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET);
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR);
sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma);
sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32);
/* Set the list last index */
sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1);
sky2_write32(hw, STAT_TX_TIMER_INI, sky2_ms2clk(hw, 10));
/* These status setup values are copied from SysKonnect's driver */
if (is_ec_a1(hw)) {
/* WA for dev. #4.3 */
sky2_write16(hw, STAT_TX_IDX_TH, 0xfff); /* Tx Threshold */
/* set Status-FIFO watermark */
sky2_write8(hw, STAT_FIFO_WM, 0x21); /* WA for dev. #4.18 */
/* set Status-FIFO ISR watermark */
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x07); /* WA for dev. #4.18 */
} else {
sky2_write16(hw, STAT_TX_IDX_TH, 0x000a);
/* set Status-FIFO watermark */
sky2_write8(hw, STAT_FIFO_WM, 0x10);
/* set Status-FIFO ISR watermark */
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0)
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x10);
else /* WA 4109 */
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x04);
sky2_write32(hw, STAT_ISR_TIMER_INI, 0x0190);
}
/* enable status unit */
sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON);
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
return 0;
}
static inline u32 sky2_supported_modes(const struct sky2_hw *hw)
{
u32 modes;
if (hw->copper) {
modes = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
| SUPPORTED_100baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
if (hw->chip_id != CHIP_ID_YUKON_FE)
modes |= SUPPORTED_1000baseT_Half
| SUPPORTED_1000baseT_Full;
} else
modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
| SUPPORTED_Autoneg;
return modes;
}
static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = sky2_supported_modes(hw);
ecmd->phy_address = PHY_ADDR_MARV;
if (hw->copper) {
ecmd->supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
| SUPPORTED_100baseT_Full
| SUPPORTED_1000baseT_Half
| SUPPORTED_1000baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
ecmd->port = PORT_TP;
} else
ecmd->port = PORT_FIBRE;
ecmd->advertising = sky2->advertising;
ecmd->autoneg = sky2->autoneg;
ecmd->speed = sky2->speed;
ecmd->duplex = sky2->duplex;
return 0;
}
static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
const struct sky2_hw *hw = sky2->hw;
u32 supported = sky2_supported_modes(hw);
if (ecmd->autoneg == AUTONEG_ENABLE) {
ecmd->advertising = supported;
sky2->duplex = -1;
sky2->speed = -1;
} else {
u32 setting;
switch (ecmd->speed) {
case SPEED_1000:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_1000baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_1000baseT_Half;
else
return -EINVAL;
break;
case SPEED_100:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_100baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_100baseT_Half;
else
return -EINVAL;
break;
case SPEED_10:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_10baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_10baseT_Half;
else
return -EINVAL;
break;
default:
return -EINVAL;
}
if ((setting & supported) == 0)
return -EINVAL;
sky2->speed = ecmd->speed;
sky2->duplex = ecmd->duplex;
}
sky2->autoneg = ecmd->autoneg;
sky2->advertising = ecmd->advertising;
if (netif_running(dev)) {
sky2_down(dev);
sky2_up(dev);
}
return 0;
}
static void sky2_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
struct sky2_port *sky2 = netdev_priv(dev);
strcpy(info->driver, DRV_NAME);
strcpy(info->version, DRV_VERSION);
strcpy(info->fw_version, "N/A");
strcpy(info->bus_info, pci_name(sky2->hw->pdev));
}
static const struct sky2_stat {
char name[ETH_GSTRING_LEN];
u16 offset;
} sky2_stats[] = {
{ "tx_bytes", GM_TXO_OK_HI },
{ "rx_bytes", GM_RXO_OK_HI },
{ "tx_broadcast", GM_TXF_BC_OK },
{ "rx_broadcast", GM_RXF_BC_OK },
{ "tx_multicast", GM_TXF_MC_OK },
{ "rx_multicast", GM_RXF_MC_OK },
{ "tx_unicast", GM_TXF_UC_OK },
{ "rx_unicast", GM_RXF_UC_OK },
{ "tx_mac_pause", GM_TXF_MPAUSE },
{ "rx_mac_pause", GM_RXF_MPAUSE },
{ "collisions", GM_TXF_SNG_COL },
{ "late_collision",GM_TXF_LAT_COL },
{ "aborted", GM_TXF_ABO_COL },
{ "multi_collisions", GM_TXF_MUL_COL },
{ "fifo_underrun", GM_TXE_FIFO_UR },
{ "fifo_overflow", GM_RXE_FIFO_OV },
{ "rx_toolong", GM_RXF_LNG_ERR },
{ "rx_jabber", GM_RXF_JAB_PKT },
{ "rx_runt", GM_RXE_FRAG },
{ "rx_too_long", GM_RXF_LNG_ERR },
{ "rx_fcs_error", GM_RXF_FCS_ERR },
};
static u32 sky2_get_rx_csum(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
return sky2->rx_csum;
}
static int sky2_set_rx_csum(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2->rx_csum = data;
sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
return 0;
}
static u32 sky2_get_msglevel(struct net_device *netdev)
{
struct sky2_port *sky2 = netdev_priv(netdev);
return sky2->msg_enable;
}
static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
int i;
data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
| (u64) gma_read32(hw, port, GM_TXO_OK_LO);
data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
| (u64) gma_read32(hw, port, GM_RXO_OK_LO);
for (i = 2; i < count; i++)
data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset);
}
static void sky2_set_msglevel(struct net_device *netdev, u32 value)
{
struct sky2_port *sky2 = netdev_priv(netdev);
sky2->msg_enable = value;
}
static int sky2_get_stats_count(struct net_device *dev)
{
return ARRAY_SIZE(sky2_stats);
}
static void sky2_get_ethtool_stats(struct net_device *dev,
struct ethtool_stats *stats, u64 * data)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats));
}
static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data)
{
int i;
switch (stringset) {
case ETH_SS_STATS:
for (i = 0; i < ARRAY_SIZE(sky2_stats); i++)
memcpy(data + i * ETH_GSTRING_LEN,
sky2_stats[i].name, ETH_GSTRING_LEN);
break;
}
}
/* Use hardware MIB variables for critical path statistics and
* transmit feedback not reported at interrupt.
* Other errors are accounted for in interrupt handler.
*/
static struct net_device_stats *sky2_get_stats(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
u64 data[13];
sky2_phy_stats(sky2, data, ARRAY_SIZE(data));
sky2->net_stats.tx_bytes = data[0];
sky2->net_stats.rx_bytes = data[1];
sky2->net_stats.tx_packets = data[2] + data[4] + data[6];
sky2->net_stats.rx_packets = data[3] + data[5] + data[7];
sky2->net_stats.multicast = data[5] + data[7];
sky2->net_stats.collisions = data[10];
sky2->net_stats.tx_aborted_errors = data[12];
return &sky2->net_stats;
}
static int sky2_set_mac_address(struct net_device *dev, void *p)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sockaddr *addr = p;
int err = 0;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
sky2_down(dev);
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8,
dev->dev_addr, ETH_ALEN);
memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8,
dev->dev_addr, ETH_ALEN);
if (dev->flags & IFF_UP)
err = sky2_up(dev);
return err;
}
static void sky2_set_multicast(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
struct dev_mc_list *list = dev->mc_list;
u16 reg;
u8 filter[8];
memset(filter, 0, sizeof(filter));
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA;
if (dev->flags & IFF_PROMISC) /* promiscious */
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16) /* all multicast */
memset(filter, 0xff, sizeof(filter));
else if (dev->mc_count == 0) /* no multicast */
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
reg |= GM_RXCR_MCF_ENA;
for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
filter[bit / 8] |= 1 << (bit % 8);
}
}
gma_write16(hw, port, GM_MC_ADDR_H1,
(u16) filter[0] | ((u16) filter[1] << 8));
gma_write16(hw, port, GM_MC_ADDR_H2,
(u16) filter[2] | ((u16) filter[3] << 8));
gma_write16(hw, port, GM_MC_ADDR_H3,
(u16) filter[4] | ((u16) filter[5] << 8));
gma_write16(hw, port, GM_MC_ADDR_H4,
(u16) filter[6] | ((u16) filter[7] << 8));
gma_write16(hw, port, GM_RX_CTRL, reg);
}
/* Can have one global because blinking is controlled by
* ethtool and that is always under RTNL mutex
*/
static inline void sky2_led(struct sky2_hw *hw, unsigned port, int on)
{
u16 pg;
spin_lock_bh(&hw->phy_lock);
switch (hw->chip_id) {
case CHIP_ID_YUKON_XL:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
on ? (PHY_M_LEDC_LOS_CTRL(1) |
PHY_M_LEDC_INIT_CTRL(7) |
PHY_M_LEDC_STA1_CTRL(7) |
PHY_M_LEDC_STA0_CTRL(7))
: 0);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
default:
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
gm_phy_write(hw, port, PHY_MARV_LED_OVER,
on ? PHY_M_LED_MO_DUP(MO_LED_ON) |
PHY_M_LED_MO_10(MO_LED_ON) |
PHY_M_LED_MO_100(MO_LED_ON) |
PHY_M_LED_MO_1000(MO_LED_ON) |
PHY_M_LED_MO_RX(MO_LED_ON)
: PHY_M_LED_MO_DUP(MO_LED_OFF) |
PHY_M_LED_MO_10(MO_LED_OFF) |
PHY_M_LED_MO_100(MO_LED_OFF) |
PHY_M_LED_MO_1000(MO_LED_OFF) |
PHY_M_LED_MO_RX(MO_LED_OFF));
}
spin_unlock_bh(&hw->phy_lock);
}
/* blink LED's for finding board */
static int sky2_phys_id(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 ledctrl, ledover = 0;
long ms;
int onoff = 1;
if (!data || data > (u32) (MAX_SCHEDULE_TIMEOUT / HZ))
ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT);
else
ms = data * 1000;
/* save initial values */
spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
ledctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
} else {
ledctrl = gm_phy_read(hw, port, PHY_MARV_LED_CTRL);
ledover = gm_phy_read(hw, port, PHY_MARV_LED_OVER);
}
spin_unlock_bh(&hw->phy_lock);
while (ms > 0) {
sky2_led(hw, port, onoff);
onoff = !onoff;
if (msleep_interruptible(250))
break; /* interrupted */
ms -= 250;
}
/* resume regularly scheduled programming */
spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ledctrl);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
} else {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
}
spin_unlock_bh(&hw->phy_lock);
return 0;
}
static void sky2_get_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
ecmd->tx_pause = sky2->tx_pause;
ecmd->rx_pause = sky2->rx_pause;
ecmd->autoneg = sky2->autoneg;
}
static int sky2_set_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
int err = 0;
sky2->autoneg = ecmd->autoneg;
sky2->tx_pause = ecmd->tx_pause != 0;
sky2->rx_pause = ecmd->rx_pause != 0;
if (netif_running(dev)) {
sky2_down(dev);
err = sky2_up(dev);
}
return err;
}
#ifdef CONFIG_PM
static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct sky2_port *sky2 = netdev_priv(dev);
wol->supported = WAKE_MAGIC;
wol->wolopts = sky2->wol ? WAKE_MAGIC : 0;
}
static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
if (wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
return -EOPNOTSUPP;
sky2->wol = wol->wolopts == WAKE_MAGIC;
if (sky2->wol) {
memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
sky2_write16(hw, WOL_CTRL_STAT,
WOL_CTL_ENA_PME_ON_MAGIC_PKT |
WOL_CTL_ENA_MAGIC_PKT_UNIT);
} else
sky2_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
return 0;
}
#endif
static void sky2_get_ringparam(struct net_device *dev,
struct ethtool_ringparam *ering)
{
struct sky2_port *sky2 = netdev_priv(dev);
ering->rx_max_pending = RX_MAX_PENDING;
ering->rx_mini_max_pending = 0;
ering->rx_jumbo_max_pending = 0;
ering->tx_max_pending = TX_RING_SIZE - 1;
ering->rx_pending = sky2->rx_pending;
ering->rx_mini_pending = 0;
ering->rx_jumbo_pending = 0;
ering->tx_pending = sky2->tx_pending;
}
static int sky2_set_ringparam(struct net_device *dev,
struct ethtool_ringparam *ering)
{
struct sky2_port *sky2 = netdev_priv(dev);
int err = 0;
if (ering->rx_pending > RX_MAX_PENDING ||
ering->rx_pending < 8 ||
ering->tx_pending < MAX_SKB_TX_LE ||
ering->tx_pending > TX_RING_SIZE - 1)
return -EINVAL;
if (netif_running(dev))
sky2_down(dev);
sky2->rx_pending = ering->rx_pending;
sky2->tx_pending = ering->tx_pending;
if (netif_running(dev))
err = sky2_up(dev);
return err;
}
#define SKY2_REGS_LEN 0x1000
static int sky2_get_regs_len(struct net_device *dev)
{
return SKY2_REGS_LEN;
}
/*
* Returns copy of control register region
* I/O region is divided into banks and certain regions are unreadable
*/
static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *p)
{
const struct sky2_port *sky2 = netdev_priv(dev);
unsigned long offs;
const void __iomem *io = sky2->hw->regs;
static const unsigned long bankmap = 0xfff3f305;
regs->version = 1;
for (offs = 0; offs < regs->len; offs += 128) {
u32 len = min_t(u32, 128, regs->len - offs);
if (bankmap & (1 << (offs / 128)))
memcpy_fromio(p + offs, io + offs, len);
else
memset(p + offs, 0, len);
}
}
static struct ethtool_ops sky2_ethtool_ops = {
.get_settings = sky2_get_settings,
.set_settings = sky2_set_settings,
.get_drvinfo = sky2_get_drvinfo,
.get_msglevel = sky2_get_msglevel,
.set_msglevel = sky2_set_msglevel,
.get_regs_len = sky2_get_regs_len,
.get_regs = sky2_get_regs,
.get_link = ethtool_op_get_link,
.get_sg = ethtool_op_get_sg,
.set_sg = ethtool_op_set_sg,
.get_tx_csum = ethtool_op_get_tx_csum,
.set_tx_csum = ethtool_op_set_tx_csum,
.get_tso = ethtool_op_get_tso,
.set_tso = ethtool_op_set_tso,
.get_rx_csum = sky2_get_rx_csum,
.set_rx_csum = sky2_set_rx_csum,
.get_strings = sky2_get_strings,
.get_ringparam = sky2_get_ringparam,
.set_ringparam = sky2_set_ringparam,
.get_pauseparam = sky2_get_pauseparam,
.set_pauseparam = sky2_set_pauseparam,
#ifdef CONFIG_PM
.get_wol = sky2_get_wol,
.set_wol = sky2_set_wol,
#endif
.phys_id = sky2_phys_id,
.get_stats_count = sky2_get_stats_count,
.get_ethtool_stats = sky2_get_ethtool_stats,
};
/* Initialize network device */
static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
unsigned port, int highmem)
{
struct sky2_port *sky2;
struct net_device *dev = alloc_etherdev(sizeof(*sky2));
if (!dev) {
printk(KERN_ERR "sky2 etherdev alloc failed");
return NULL;
}
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &hw->pdev->dev);
dev->open = sky2_up;
dev->stop = sky2_down;
dev->hard_start_xmit = sky2_xmit_frame;
dev->get_stats = sky2_get_stats;
dev->set_multicast_list = sky2_set_multicast;
dev->set_mac_address = sky2_set_mac_address;
dev->change_mtu = sky2_change_mtu;
SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
dev->tx_timeout = sky2_tx_timeout;
dev->watchdog_timeo = TX_WATCHDOG;
if (port == 0)
dev->poll = sky2_poll;
dev->weight = NAPI_WEIGHT;
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = sky2_netpoll;
#endif
sky2 = netdev_priv(dev);
sky2->netdev = dev;
sky2->hw = hw;
sky2->msg_enable = netif_msg_init(debug, default_msg);
spin_lock_init(&sky2->tx_lock);
/* Auto speed and flow control */
sky2->autoneg = AUTONEG_ENABLE;
sky2->tx_pause = 0;
sky2->rx_pause = 1;
sky2->duplex = -1;
sky2->speed = -1;
sky2->advertising = sky2_supported_modes(hw);
sky2->rx_csum = 1;
tasklet_init(&sky2->phy_task, sky2_phy_task, (unsigned long)sky2);
sky2->tx_pending = TX_DEF_PENDING;
sky2->rx_pending = is_ec_a1(hw) ? 8 : RX_DEF_PENDING;
hw->dev[port] = dev;
sky2->port = port;
dev->features |= NETIF_F_LLTX | NETIF_F_TSO;
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
/* read the mac address */
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
/* device is off until link detection */
netif_carrier_off(dev);
netif_stop_queue(dev);
return dev;
}
static inline void sky2_show_addr(struct net_device *dev)
{
const struct sky2_port *sky2 = netdev_priv(dev);
if (netif_msg_probe(sky2))
printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
dev->name,
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
}
static int __devinit sky2_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
struct net_device *dev, *dev1 = NULL;
struct sky2_hw *hw;
int err, using_dac = 0;
err = pci_enable_device(pdev);
if (err) {
printk(KERN_ERR PFX "%s cannot enable PCI device\n",
pci_name(pdev));
goto err_out;
}
err = pci_request_regions(pdev, DRV_NAME);
if (err) {
printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
pci_name(pdev));
goto err_out;
}
pci_set_master(pdev);
if (sizeof(dma_addr_t) > sizeof(u32)) {
err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
if (!err)
using_dac = 1;
}
if (!using_dac) {
err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (err) {
printk(KERN_ERR PFX "%s no usable DMA configuration\n",
pci_name(pdev));
goto err_out_free_regions;
}
}
#ifdef __BIG_ENDIAN
/* byte swap decriptors in hardware */
{
u32 reg;
pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
reg |= PCI_REV_DESC;
pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
}
#endif
err = -ENOMEM;
hw = kmalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
pci_name(pdev));
goto err_out_free_regions;
}
memset(hw, 0, sizeof(*hw));
hw->pdev = pdev;
spin_lock_init(&hw->phy_lock);
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
printk(KERN_ERR PFX "%s: cannot map device registers\n",
pci_name(pdev));
goto err_out_free_hw;
}
err = sky2_reset(hw);
if (err)
goto err_out_iounmap;
printk(KERN_INFO PFX "addr 0x%lx irq %d Yukon-%s (0x%x) rev %d\n",
pci_resource_start(pdev, 0), pdev->irq,
yukon_name[hw->chip_id - CHIP_ID_YUKON],
hw->chip_id, hw->chip_rev);
dev = sky2_init_netdev(hw, 0, using_dac);
if (!dev)
goto err_out_free_pci;
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "%s: cannot register net device\n",
pci_name(pdev));
goto err_out_free_netdev;
}
sky2_show_addr(dev);
if (hw->ports > 1 && (dev1 = sky2_init_netdev(hw, 1, using_dac))) {
if (register_netdev(dev1) == 0)
sky2_show_addr(dev1);
else {
/* Failure to register second port need not be fatal */
printk(KERN_WARNING PFX
"register of second port failed\n");
hw->dev[1] = NULL;
free_netdev(dev1);
}
}
err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
if (err) {
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
pci_name(pdev), pdev->irq);
goto err_out_unregister;
}
hw->intr_mask = Y2_IS_BASE;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
pci_set_drvdata(pdev, hw);
return 0;
err_out_unregister:
if (dev1) {
unregister_netdev(dev1);
free_netdev(dev1);
}
unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
err_out_free_pci:
sky2_write8(hw, B0_CTST, CS_RST_SET);
pci_free_consistent(hw->pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
err_out_iounmap:
iounmap(hw->regs);
err_out_free_hw:
kfree(hw);
err_out_free_regions:
pci_release_regions(pdev);
pci_disable_device(pdev);
err_out:
return err;
}
static void __devexit sky2_remove(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
struct net_device *dev0, *dev1;
if (!hw)
return;
dev0 = hw->dev[0];
dev1 = hw->dev[1];
if (dev1)
unregister_netdev(dev1);
unregister_netdev(dev0);
sky2_write32(hw, B0_IMSK, 0);
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
sky2_write8(hw, B0_CTST, CS_RST_SET);
free_irq(pdev->irq, hw);
pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
pci_release_regions(pdev);
pci_disable_device(pdev);
if (dev1)
free_netdev(dev1);
free_netdev(dev0);
iounmap(hw->regs);
kfree(hw);
pci_set_drvdata(pdev, NULL);
}
#ifdef CONFIG_PM
static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
int i, wol = 0;
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
if (dev) {
struct sky2_port *sky2 = netdev_priv(dev);
if (netif_running(dev)) {
netif_carrier_off(dev);
sky2_down(dev);
}
netif_device_detach(dev);
wol |= sky2->wol;
}
}
pci_save_state(pdev);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
pci_disable_device(pdev);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
return 0;
}
static int sky2_resume(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
int i;
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
sky2_reset(hw);
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
if (dev) {
netif_device_attach(dev);
if (netif_running(dev))
sky2_up(dev);
}
}
return 0;
}
#endif
static struct pci_driver sky2_driver = {
.name = DRV_NAME,
.id_table = sky2_id_table,
.probe = sky2_probe,
.remove = __devexit_p(sky2_remove),
#ifdef CONFIG_PM
.suspend = sky2_suspend,
.resume = sky2_resume,
#endif
};
static int __init sky2_init_module(void)
{
return pci_module_init(&sky2_driver);
}
static void __exit sky2_cleanup_module(void)
{
pci_unregister_driver(&sky2_driver);
}
module_init(sky2_init_module);
module_exit(sky2_cleanup_module);
MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
MODULE_LICENSE("GPL");