forked from luck/tmp_suning_uos_patched
a7dacb68b3
At this moment in time the memcpy channels which can be used by the D40 are fixed, as each supported platform in Mainline uses the same ones. However, platforms do exist which don't follow this convention, so these will need to be tailored. Fortunately, these platforms will be DT only, so this change has very little impact on platform data. Cc: Dan Williams <djbw@fb.com> Cc: Per Forlin <per.forlin@stericsson.com> Cc: Rabin Vincent <rabin@rab.in> Acked-by: Vinod Koul <vinod.koul@intel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
210 lines
6.0 KiB
C
210 lines
6.0 KiB
C
/*
|
|
* Copyright (C) ST-Ericsson SA 2007-2010
|
|
* Author: Per Forlin <per.forlin@stericsson.com> for ST-Ericsson
|
|
* Author: Jonas Aaberg <jonas.aberg@stericsson.com> for ST-Ericsson
|
|
* License terms: GNU General Public License (GPL) version 2
|
|
*/
|
|
|
|
|
|
#ifndef STE_DMA40_H
|
|
#define STE_DMA40_H
|
|
|
|
#include <linux/dmaengine.h>
|
|
#include <linux/scatterlist.h>
|
|
#include <linux/workqueue.h>
|
|
#include <linux/interrupt.h>
|
|
|
|
/*
|
|
* Maxium size for a single dma descriptor
|
|
* Size is limited to 16 bits.
|
|
* Size is in the units of addr-widths (1,2,4,8 bytes)
|
|
* Larger transfers will be split up to multiple linked desc
|
|
*/
|
|
#define STEDMA40_MAX_SEG_SIZE 0xFFFF
|
|
|
|
/* dev types for memcpy */
|
|
#define STEDMA40_DEV_DST_MEMORY (-1)
|
|
#define STEDMA40_DEV_SRC_MEMORY (-1)
|
|
|
|
enum stedma40_mode {
|
|
STEDMA40_MODE_LOGICAL = 0,
|
|
STEDMA40_MODE_PHYSICAL,
|
|
STEDMA40_MODE_OPERATION,
|
|
};
|
|
|
|
enum stedma40_mode_opt {
|
|
STEDMA40_PCHAN_BASIC_MODE = 0,
|
|
STEDMA40_LCHAN_SRC_LOG_DST_LOG = 0,
|
|
STEDMA40_PCHAN_MODULO_MODE,
|
|
STEDMA40_PCHAN_DOUBLE_DST_MODE,
|
|
STEDMA40_LCHAN_SRC_PHY_DST_LOG,
|
|
STEDMA40_LCHAN_SRC_LOG_DST_PHY,
|
|
};
|
|
|
|
#define STEDMA40_ESIZE_8_BIT 0x0
|
|
#define STEDMA40_ESIZE_16_BIT 0x1
|
|
#define STEDMA40_ESIZE_32_BIT 0x2
|
|
#define STEDMA40_ESIZE_64_BIT 0x3
|
|
|
|
/* The value 4 indicates that PEN-reg shall be set to 0 */
|
|
#define STEDMA40_PSIZE_PHY_1 0x4
|
|
#define STEDMA40_PSIZE_PHY_2 0x0
|
|
#define STEDMA40_PSIZE_PHY_4 0x1
|
|
#define STEDMA40_PSIZE_PHY_8 0x2
|
|
#define STEDMA40_PSIZE_PHY_16 0x3
|
|
|
|
/*
|
|
* The number of elements differ in logical and
|
|
* physical mode
|
|
*/
|
|
#define STEDMA40_PSIZE_LOG_1 STEDMA40_PSIZE_PHY_2
|
|
#define STEDMA40_PSIZE_LOG_4 STEDMA40_PSIZE_PHY_4
|
|
#define STEDMA40_PSIZE_LOG_8 STEDMA40_PSIZE_PHY_8
|
|
#define STEDMA40_PSIZE_LOG_16 STEDMA40_PSIZE_PHY_16
|
|
|
|
/* Maximum number of possible physical channels */
|
|
#define STEDMA40_MAX_PHYS 32
|
|
|
|
enum stedma40_flow_ctrl {
|
|
STEDMA40_NO_FLOW_CTRL,
|
|
STEDMA40_FLOW_CTRL,
|
|
};
|
|
|
|
/**
|
|
* struct stedma40_half_channel_info - dst/src channel configuration
|
|
*
|
|
* @big_endian: true if the src/dst should be read as big endian
|
|
* @data_width: Data width of the src/dst hardware
|
|
* @p_size: Burst size
|
|
* @flow_ctrl: Flow control on/off.
|
|
*/
|
|
struct stedma40_half_channel_info {
|
|
bool big_endian;
|
|
enum dma_slave_buswidth data_width;
|
|
int psize;
|
|
enum stedma40_flow_ctrl flow_ctrl;
|
|
};
|
|
|
|
/**
|
|
* struct stedma40_chan_cfg - Structure to be filled by client drivers.
|
|
*
|
|
* @dir: MEM 2 MEM, PERIPH 2 MEM , MEM 2 PERIPH, PERIPH 2 PERIPH
|
|
* @high_priority: true if high-priority
|
|
* @realtime: true if realtime mode is to be enabled. Only available on DMA40
|
|
* version 3+, i.e DB8500v2+
|
|
* @mode: channel mode: physical, logical, or operation
|
|
* @mode_opt: options for the chosen channel mode
|
|
* @dev_type: src/dst device type (driver uses dir to figure out which)
|
|
* @src_info: Parameters for dst half channel
|
|
* @dst_info: Parameters for dst half channel
|
|
* @use_fixed_channel: if true, use physical channel specified by phy_channel
|
|
* @phy_channel: physical channel to use, only if use_fixed_channel is true
|
|
*
|
|
* This structure has to be filled by the client drivers.
|
|
* It is recommended to do all dma configurations for clients in the machine.
|
|
*
|
|
*/
|
|
struct stedma40_chan_cfg {
|
|
enum dma_transfer_direction dir;
|
|
bool high_priority;
|
|
bool realtime;
|
|
enum stedma40_mode mode;
|
|
enum stedma40_mode_opt mode_opt;
|
|
int dev_type;
|
|
struct stedma40_half_channel_info src_info;
|
|
struct stedma40_half_channel_info dst_info;
|
|
|
|
bool use_fixed_channel;
|
|
int phy_channel;
|
|
};
|
|
|
|
/**
|
|
* struct stedma40_platform_data - Configuration struct for the dma device.
|
|
*
|
|
* @dev_tx: mapping between destination event line and io address
|
|
* @dev_rx: mapping between source event line and io address
|
|
* @disabled_channels: A vector, ending with -1, that marks physical channels
|
|
* that are for different reasons not available for the driver.
|
|
* @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
|
|
* which avoids HW bug that exists in some versions of the controller.
|
|
* SoftLLI introduces relink overhead that could impact performace for
|
|
* certain use cases.
|
|
* @num_of_soft_lli_chans: The number of channels that needs to be configured
|
|
* to use SoftLLI.
|
|
* @use_esram_lcla: flag for mapping the lcla into esram region
|
|
* @num_of_memcpy_chans: The number of channels reserved for memcpy.
|
|
* @num_of_phy_chans: The number of physical channels implemented in HW.
|
|
* 0 means reading the number of channels from DMA HW but this is only valid
|
|
* for 'multiple of 4' channels, like 8.
|
|
*/
|
|
struct stedma40_platform_data {
|
|
int disabled_channels[STEDMA40_MAX_PHYS];
|
|
int *soft_lli_chans;
|
|
int num_of_soft_lli_chans;
|
|
bool use_esram_lcla;
|
|
int num_of_memcpy_chans;
|
|
int num_of_phy_chans;
|
|
};
|
|
|
|
#ifdef CONFIG_STE_DMA40
|
|
|
|
/**
|
|
* stedma40_filter() - Provides stedma40_chan_cfg to the
|
|
* ste_dma40 dma driver via the dmaengine framework.
|
|
* does some checking of what's provided.
|
|
*
|
|
* Never directly called by client. It used by dmaengine.
|
|
* @chan: dmaengine handle.
|
|
* @data: Must be of type: struct stedma40_chan_cfg and is
|
|
* the configuration of the framework.
|
|
*
|
|
*
|
|
*/
|
|
|
|
bool stedma40_filter(struct dma_chan *chan, void *data);
|
|
|
|
/**
|
|
* stedma40_slave_mem() - Transfers a raw data buffer to or from a slave
|
|
* (=device)
|
|
*
|
|
* @chan: dmaengine handle
|
|
* @addr: source or destination physicall address.
|
|
* @size: bytes to transfer
|
|
* @direction: direction of transfer
|
|
* @flags: is actually enum dma_ctrl_flags. See dmaengine.h
|
|
*/
|
|
|
|
static inline struct
|
|
dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
|
|
dma_addr_t addr,
|
|
unsigned int size,
|
|
enum dma_transfer_direction direction,
|
|
unsigned long flags)
|
|
{
|
|
struct scatterlist sg;
|
|
sg_init_table(&sg, 1);
|
|
sg.dma_address = addr;
|
|
sg.length = size;
|
|
|
|
return dmaengine_prep_slave_sg(chan, &sg, 1, direction, flags);
|
|
}
|
|
|
|
#else
|
|
static inline bool stedma40_filter(struct dma_chan *chan, void *data)
|
|
{
|
|
return false;
|
|
}
|
|
|
|
static inline struct
|
|
dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
|
|
dma_addr_t addr,
|
|
unsigned int size,
|
|
enum dma_transfer_direction direction,
|
|
unsigned long flags)
|
|
{
|
|
return NULL;
|
|
}
|
|
#endif
|
|
|
|
#endif
|