AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
a012370322
kernel_optimize_test/drivers/isdn/hisax/sedlbauer_cs.c
Karsten Keil 84d370b906 [PATCH] i4l: Sedlbauer speed star II V 3.1 exist with various subversions 
the 4th id field should be not used

Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-14 14:34:17 -07:00

649 lines
22 KiB
C
Raw Blame History

/*======================================================================
A Sedlbauer PCMCIA client driver
This driver is for the Sedlbauer Speed Star and Speed Star II,
which are ISDN PCMCIA Cards.
The contents of this file are subject to the Mozilla Public
License Version 1.1 (the "License"); you may not use this file
except in compliance with the License. You may obtain a copy of
the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
implied. See the License for the specific language governing
rights and limitations under the License.
The initial developer of the original code is David A. Hinds
<dahinds@users.sourceforge.net>. Portions created by David A. Hinds
are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
Modifications from dummy_cs.c are Copyright (C) 1999-2001 Marcus Niemann
<maniemann@users.sourceforge.net>. All Rights Reserved.
Alternatively, the contents of this file may be used under the
terms of the GNU General Public License version 2 (the "GPL"), in
which case the provisions of the GPL are applicable instead of the
above. If you wish to allow the use of your version of this file
only under the terms of the GPL and not to allow others to use
your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the notice
and other provisions required by the GPL. If you do not delete
the provisions above, a recipient may use your version of this
file under either the MPL or the GPL.
======================================================================*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/ioport.h>
#include <asm/io.h>
#include <asm/system.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
#include <pcmcia/cistpl.h>
#include <pcmcia/cisreg.h>
#include <pcmcia/ds.h>
#include "hisax_cfg.h"
MODULE_DESCRIPTION("ISDN4Linux: PCMCIA client driver for Sedlbauer cards");
MODULE_AUTHOR("Marcus Niemann");
MODULE_LICENSE("Dual MPL/GPL");
/*
All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
you do not define PCMCIA_DEBUG at all, all the debug code will be
left out. If you compile with PCMCIA_DEBUG=0, the debug code will
be present but disabled -- but it can then be enabled for specific
modules at load time with a 'pc_debug=#' option to insmod.
*/
#ifdef PCMCIA_DEBUG
static int pc_debug = PCMCIA_DEBUG;
module_param(pc_debug, int, 0);
#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args);
static char *version =
"sedlbauer_cs.c 1.1a 2001/01/28 15:04:04 (M.Niemann)";
#else
#define DEBUG(n, args...)
#endif
/*====================================================================*/
/* Parameters that can be set with 'insmod' */
static int protocol = 2; /* EURO-ISDN Default */
module_param(protocol, int, 0);
/*====================================================================*/
/*
The event() function is this driver's Card Services event handler.
It will be called by Card Services when an appropriate card status
event is received. The config() and release() entry points are
used to configure or release a socket, in response to card
insertion and ejection events. They are invoked from the sedlbauer
event handler.
*/
static void sedlbauer_config(dev_link_t *link);
static void sedlbauer_release(dev_link_t *link);
static int sedlbauer_event(event_t event, int priority,
event_callback_args_t *args);
/*
The attach() and detach() entry points are used to create and destroy
"instances" of the driver, where each instance represents everything
needed to manage one actual PCMCIA card.
*/
static dev_link_t *sedlbauer_attach(void);
static void sedlbauer_detach(dev_link_t *);
/*
You'll also need to prototype all the functions that will actually
be used to talk to your device. See 'memory_cs' for a good example
of a fully self-sufficient driver; the other drivers rely more or
less on other parts of the kernel.
*/
/*
The dev_info variable is the "key" that is used to match up this
device driver with appropriate cards, through the card configuration
database.
*/
static dev_info_t dev_info = "sedlbauer_cs";
/*
A linked list of "instances" of the sedlbauer device. Each actual
PCMCIA card corresponds to one device instance, and is described
by one dev_link_t structure (defined in ds.h).
You may not want to use a linked list for this -- for example, the
memory card driver uses an array of dev_link_t pointers, where minor
device numbers are used to derive the corresponding array index.
*/
static dev_link_t *dev_list = NULL;
/*
A dev_link_t structure has fields for most things that are needed
to keep track of a socket, but there will usually be some device
specific information that also needs to be kept track of. The
'priv' pointer in a dev_link_t structure can be used to point to
a device-specific private data structure, like this.
To simplify the data structure handling, we actually include the
dev_link_t structure in the device's private data structure.
A driver needs to provide a dev_node_t structure for each device
on a card. In some cases, there is only one device per card (for
example, ethernet cards, modems). In other cases, there may be
many actual or logical devices (SCSI adapters, memory cards with
multiple partitions). The dev_node_t structures need to be kept
in a linked list starting at the 'dev' field of a dev_link_t
structure. We allocate them in the card's private data structure,
because they generally shouldn't be allocated dynamically.
In this case, we also provide a flag to indicate if a device is
"stopped" due to a power management event, or card ejection. The
device IO routines can use a flag like this to throttle IO to a
card that is not ready to accept it.
*/
typedef struct local_info_t {
dev_link_t link;
dev_node_t node;
int stop;
int cardnr;
} local_info_t;
/*======================================================================
sedlbauer_attach() creates an "instance" of the driver, allocating
local data structures for one device. The device is registered
with Card Services.
The dev_link structure is initialized, but we don't actually
configure the card at this point -- we wait until we receive a
card insertion event.
======================================================================*/
static dev_link_t *sedlbauer_attach(void)
{
local_info_t *local;
dev_link_t *link;
client_reg_t client_reg;
int ret;
DEBUG(0, "sedlbauer_attach()\n");
/* Allocate space for private device-specific data */
local = kmalloc(sizeof(local_info_t), GFP_KERNEL);
if (!local) return NULL;
memset(local, 0, sizeof(local_info_t));
local->cardnr = -1;
link = &local->link; link->priv = local;
/* Interrupt setup */
link->irq.Attributes = IRQ_TYPE_EXCLUSIVE;
link->irq.IRQInfo1 = IRQ_LEVEL_ID;
link->irq.Handler = NULL;
/*
General socket configuration defaults can go here. In this
client, we assume very little, and rely on the CIS for almost
everything. In most clients, many details (i.e., number, sizes,
and attributes of IO windows) are fixed by the nature of the
device, and can be hard-wired here.
*/
/* from old sedl_cs
*/
/* The io structure describes IO port mapping */
link->io.NumPorts1 = 8;
link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
link->io.IOAddrLines = 3;
link->conf.Attributes = 0;
link->conf.Vcc = 50;
link->conf.IntType = INT_MEMORY_AND_IO;
/* Register with Card Services */
link->next = dev_list;
dev_list = link;
client_reg.dev_info = &dev_info;
client_reg.Version = 0x0210;
client_reg.event_callback_args.client_data = link;
ret = pcmcia_register_client(&link->handle, &client_reg);
if (ret != CS_SUCCESS) {
cs_error(link->handle, RegisterClient, ret);
sedlbauer_detach(link);
return NULL;
}
return link;
} /* sedlbauer_attach */
/*======================================================================
This deletes a driver "instance". The device is de-registered
with Card Services. If it has been released, all local data
structures are freed. Otherwise, the structures will be freed
when the device is released.
======================================================================*/
static void sedlbauer_detach(dev_link_t *link)
{
dev_link_t **linkp;
DEBUG(0, "sedlbauer_detach(0x%p)\n", link);
/* Locate device structure */
for (linkp = &dev_list; *linkp; linkp = &(*linkp)->next)
if (*linkp == link) break;
if (*linkp == NULL)
return;
/*
If the device is currently configured and active, we won't
actually delete it yet. Instead, it is marked so that when
the release() function is called, that will trigger a proper
detach().
*/
if (link->state & DEV_CONFIG) {
#ifdef PCMCIA_DEBUG
printk(KERN_DEBUG "sedlbauer_cs: detach postponed, '%s' "
"still locked\n", link->dev->dev_name);
#endif
link->state |= DEV_STALE_LINK;
return;
}
/* Break the link with Card Services */
if (link->handle)
pcmcia_deregister_client(link->handle);
/* Unlink device structure, and free it */
*linkp = link->next;
/* This points to the parent local_info_t struct */
kfree(link->priv);
} /* sedlbauer_detach */
/*======================================================================
sedlbauer_config() is scheduled to run after a CARD_INSERTION event
is received, to configure the PCMCIA socket, and to make the
device available to the system.
======================================================================*/
#define CS_CHECK(fn, ret) \
do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
static void sedlbauer_config(dev_link_t *link)
{
client_handle_t handle = link->handle;
local_info_t *dev = link->priv;
tuple_t tuple;
cisparse_t parse;
int last_fn, last_ret;
u8 buf[64];
config_info_t conf;
win_req_t req;
memreq_t map;
IsdnCard_t icard;
DEBUG(0, "sedlbauer_config(0x%p)\n", link);
/*
This reads the card's CONFIG tuple to find its configuration
registers.
*/
tuple.DesiredTuple = CISTPL_CONFIG;
tuple.Attributes = 0;
tuple.TupleData = buf;
tuple.TupleDataMax = sizeof(buf);
tuple.TupleOffset = 0;
CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(handle, &tuple));
CS_CHECK(GetTupleData, pcmcia_get_tuple_data(handle, &tuple));
CS_CHECK(ParseTuple, pcmcia_parse_tuple(handle, &tuple, &parse));
link->conf.ConfigBase = parse.config.base;
link->conf.Present = parse.config.rmask[0];
/* Configure card */
link->state |= DEV_CONFIG;
/* Look up the current Vcc */
CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(handle, &conf));
link->conf.Vcc = conf.Vcc;
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including
voltage, IO window, memory window, and interrupt settings.
We make no assumptions about the card to be configured: we use
just the information available in the CIS. In an ideal world,
this would work for any PCMCIA card, but it requires a complete
and accurate CIS. In practice, a driver usually "knows" most of
these things without consulting the CIS, and most client drivers
will only use the CIS to fill in implementation-defined details.
*/
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(handle, &tuple));
while (1) {
cistpl_cftable_entry_t dflt = { 0 };
cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
if (pcmcia_get_tuple_data(handle, &tuple) != 0 ||
pcmcia_parse_tuple(handle, &tuple, &parse) != 0)
goto next_entry;
if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg;
if (cfg->index == 0) goto next_entry;
link->conf.ConfigIndex = cfg->index;
/* Does this card need audio output? */
if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
}
/* Use power settings for Vcc and Vpp if present */
/* Note that the CIS values need to be rescaled */
if (cfg->vcc.present & (1<<CISTPL_POWER_VNOM)) {
if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM]/10000)
goto next_entry;
} else if (dflt.vcc.present & (1<<CISTPL_POWER_VNOM)) {
if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM]/10000)
goto next_entry;
}
if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
link->conf.Vpp1 = link->conf.Vpp2 =
cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
else if (dflt.vpp1.present & (1<<CISTPL_POWER_VNOM))
link->conf.Vpp1 = link->conf.Vpp2 =
dflt.vpp1.param[CISTPL_POWER_VNOM]/10000;
/* Do we need to allocate an interrupt? */
if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
link->conf.Attributes |= CONF_ENABLE_IRQ;
/* IO window settings */
link->io.NumPorts1 = link->io.NumPorts2 = 0;
if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
if (!(io->flags & CISTPL_IO_8BIT))
link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
if (!(io->flags & CISTPL_IO_16BIT))
link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
/* new in dummy.cs 2001/01/28 MN
link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
*/
link->io.BasePort1 = io->win[0].base;
link->io.NumPorts1 = io->win[0].len;
if (io->nwin > 1) {
link->io.Attributes2 = link->io.Attributes1;
link->io.BasePort2 = io->win[1].base;
link->io.NumPorts2 = io->win[1].len;
}
/* This reserves IO space but doesn't actually enable it */
if (pcmcia_request_io(link->handle, &link->io) != 0)
goto next_entry;
}
/*
Now set up a common memory window, if needed. There is room
in the dev_link_t structure for one memory window handle,
but if the base addresses need to be saved, or if multiple
windows are needed, the info should go in the private data
structure for this device.
Note that the memory window base is a physical address, and
needs to be mapped to virtual space with ioremap() before it
is used.
*/
if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
cistpl_mem_t *mem =
(cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM;
req.Attributes |= WIN_ENABLE;
req.Base = mem->win[0].host_addr;
req.Size = mem->win[0].len;
/* new in dummy.cs 2001/01/28 MN
if (req.Size < 0x1000)
req.Size = 0x1000;
*/
req.AccessSpeed = 0;
if (pcmcia_request_window(&link->handle, &req, &link->win) != 0)
goto next_entry;
map.Page = 0; map.CardOffset = mem->win[0].card_addr;
if (pcmcia_map_mem_page(link->win, &map) != 0)
goto next_entry;
}
/* If we got this far, we're cool! */
break;
next_entry:
/* new in dummy.cs 2001/01/28 MN
if (link->io.NumPorts1)
pcmcia_release_io(link->handle, &link->io);
*/
CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(handle, &tuple));
}
/*
Allocate an interrupt line. Note that this does not assign a
handler to the interrupt, unless the 'Handler' member of the
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ)
CS_CHECK(RequestIRQ, pcmcia_request_irq(link->handle, &link->irq));
/*
This actually configures the PCMCIA socket -- setting up
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link->handle, &link->conf));
/*
At this point, the dev_node_t structure(s) need to be
initialized and arranged in a linked list at link->dev.
*/
sprintf(dev->node.dev_name, "sedlbauer");
dev->node.major = dev->node.minor = 0;
link->dev = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x: Vcc %d.%d",
dev->node.dev_name, link->conf.ConfigIndex,
link->conf.Vcc/10, link->conf.Vcc%10);
if (link->conf.Vpp1)
printk(", Vpp %d.%d", link->conf.Vpp1/10, link->conf.Vpp1%10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req.Base,
req.Base+req.Size-1);
printk("\n");
link->state &= ~DEV_CONFIG_PENDING;
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_SEDLBAUER_PCMCIA;
last_ret = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->stop), &icard);
if (last_ret < 0) {
printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d at i/o %#x\n",
last_ret, link->io.BasePort1);
sedlbauer_release(link);
} else
((local_info_t*)link->priv)->cardnr = last_ret;
return;
cs_failed:
cs_error(link->handle, last_fn, last_ret);
sedlbauer_release(link);
} /* sedlbauer_config */
/*======================================================================
After a card is removed, sedlbauer_release() will unregister the
device, and release the PCMCIA configuration. If the device is
still open, this will be postponed until it is closed.
======================================================================*/
static void sedlbauer_release(dev_link_t *link)
{
local_info_t *local = link->priv;
DEBUG(0, "sedlbauer_release(0x%p)\n", link);
if (local) {
if (local->cardnr >= 0) {
/* no unregister function with hisax */
HiSax_closecard(local->cardnr);
}
}
/* Unlink the device chain */
link->dev = NULL;
/*
In a normal driver, additional code may be needed to release
other kernel data structures associated with this device.
*/
/* Don't bother checking to see if these succeed or not */
if (link->win)
pcmcia_release_window(link->win);
pcmcia_release_configuration(link->handle);
if (link->io.NumPorts1)
pcmcia_release_io(link->handle, &link->io);
if (link->irq.AssignedIRQ)
pcmcia_release_irq(link->handle, &link->irq);
link->state &= ~DEV_CONFIG;
if (link->state & DEV_STALE_LINK)
sedlbauer_detach(link);
} /* sedlbauer_release */
/*======================================================================
The card status event handler. Mostly, this schedules other
stuff to run after an event is received.
When a CARD_REMOVAL event is received, we immediately set a
private flag to block future accesses to this device. All the
functions that actually access the device should check this flag
to make sure the card is still present.
======================================================================*/
static int sedlbauer_event(event_t event, int priority,
event_callback_args_t *args)
{
dev_link_t *link = args->client_data;
local_info_t *dev = link->priv;
DEBUG(1, "sedlbauer_event(0x%06x)\n", event);
switch (event) {
case CS_EVENT_CARD_REMOVAL:
link->state &= ~DEV_PRESENT;
if (link->state & DEV_CONFIG) {
((local_info_t *)link->priv)->stop = 1;
sedlbauer_release(link);
}
break;
case CS_EVENT_CARD_INSERTION:
link->state |= DEV_PRESENT | DEV_CONFIG_PENDING;
sedlbauer_config(link);
break;
case CS_EVENT_PM_SUSPEND:
link->state |= DEV_SUSPEND;
/* Fall through... */
case CS_EVENT_RESET_PHYSICAL:
/* Mark the device as stopped, to block IO until later */
dev->stop = 1;
if (link->state & DEV_CONFIG)
pcmcia_release_configuration(link->handle);
break;
case CS_EVENT_PM_RESUME:
link->state &= ~DEV_SUSPEND;
/* Fall through... */
case CS_EVENT_CARD_RESET:
if (link->state & DEV_CONFIG)
pcmcia_request_configuration(link->handle, &link->conf);
dev->stop = 0;
/*
In a normal driver, additional code may go here to restore
the device state and restart IO.
*/
break;
}
return 0;
} /* sedlbauer_event */
static struct pcmcia_device_id sedlbauer_ids[] = {
PCMCIA_DEVICE_PROD_ID123("SEDLBAUER", "speed star II", "V 3.1", 0x81fb79f5, 0xf3612e1d, 0x6b95c78a),
PCMCIA_DEVICE_PROD_ID123("SEDLBAUER", "ISDN-Adapter", "4D67", 0x81fb79f5, 0xe4e9bc12, 0x397b7e90),
PCMCIA_DEVICE_PROD_ID123("SEDLBAUER", "ISDN-Adapter", "4D98", 0x81fb79f5, 0xe4e9bc12, 0x2e5c7fce),
PCMCIA_DEVICE_PROD_ID123("SEDLBAUER", "ISDN-Adapter", " (C) 93-94 VK", 0x81fb79f5, 0xe4e9bc12, 0x8db143fe),
PCMCIA_DEVICE_PROD_ID123("SEDLBAUER", "ISDN-Adapter", " (c) 93-95 VK", 0x81fb79f5, 0xe4e9bc12, 0xb391ab4c),
PCMCIA_DEVICE_PROD_ID12("HST High Soft Tech GmbH", "Saphir II B", 0xd79e0b84, 0x21d083ae),
/* PCMCIA_DEVICE_PROD_ID1234("SEDLBAUER", 0x81fb79f5), */ /* too generic*/
PCMCIA_DEVICE_NULL
};
MODULE_DEVICE_TABLE(pcmcia, sedlbauer_ids);
static struct pcmcia_driver sedlbauer_driver = {
.owner = THIS_MODULE,
.drv = {
.name = "sedlbauer_cs",
},
.attach = sedlbauer_attach,
.event = sedlbauer_event,
.detach = sedlbauer_detach,
.id_table = sedlbauer_ids,
};
static int __init init_sedlbauer_cs(void)
{
return pcmcia_register_driver(&sedlbauer_driver);
}
static void __exit exit_sedlbauer_cs(void)
{
pcmcia_unregister_driver(&sedlbauer_driver);
BUG_ON(dev_list != NULL);
}
module_init(init_sedlbauer_cs);
module_exit(exit_sedlbauer_cs);
View Git Blame Copy Permalink