forked from luck/tmp_suning_uos_patched
f7214ff4e8
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
309 lines
10 KiB
Plaintext
309 lines
10 KiB
Plaintext
#
|
|
# USB Input driver configuration
|
|
#
|
|
comment "USB Input Devices"
|
|
depends on USB
|
|
|
|
config USB_HID
|
|
tristate "USB Human Interface Device (full HID) support"
|
|
depends on USB
|
|
---help---
|
|
Say Y here if you want full HID support to connect keyboards,
|
|
mice, joysticks, graphic tablets, or any other HID based devices
|
|
to your computer via USB. You also need to select HID Input layer
|
|
support (below) if you want to use keyboards, mice, joysticks and
|
|
the like ... as well as Uninterruptible Power Supply (UPS) and
|
|
monitor control devices.
|
|
|
|
You can't use this driver and the HIDBP (Boot Protocol) keyboard
|
|
and mouse drivers at the same time. More information is available:
|
|
<file:Documentation/input/input.txt>.
|
|
|
|
If unsure, say Y.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbhid.
|
|
|
|
comment "Input core support is needed for USB HID input layer or HIDBP support"
|
|
depends on USB_HID && INPUT=n
|
|
|
|
config USB_HIDINPUT
|
|
bool "HID input layer support"
|
|
default y
|
|
depends on INPUT && USB_HID
|
|
help
|
|
Say Y here if you want to use a USB keyboard, mouse or joystick,
|
|
or any other HID input device.
|
|
|
|
If unsure, say Y.
|
|
|
|
config HID_FF
|
|
bool "Force feedback support (EXPERIMENTAL)"
|
|
depends on USB_HIDINPUT && EXPERIMENTAL
|
|
help
|
|
Say Y here is you want force feedback support for a few HID devices.
|
|
See below for a list of supported devices.
|
|
|
|
See <file:Documentation/input/ff.txt> for a description of the force
|
|
feedback API.
|
|
|
|
If unsure, say N.
|
|
|
|
config HID_PID
|
|
bool "PID Devices (Microsoft Sidewinder Force Feedback 2)"
|
|
depends on HID_FF
|
|
help
|
|
Say Y here if you have a PID-compliant joystick and wish to enable force
|
|
feedback for it. The Microsoft Sidewinder Force Feedback 2 is one such
|
|
device.
|
|
|
|
config LOGITECH_FF
|
|
bool "Logitech WingMan *3D support"
|
|
depends on HID_FF
|
|
help
|
|
Say Y here if you have one of these devices:
|
|
- Logitech WingMan Cordless RumblePad
|
|
- Logitech WingMan Force 3D
|
|
and if you want to enable force feedback for them.
|
|
Note: if you say N here, this device will still be supported, but without
|
|
force feedback.
|
|
|
|
config THRUSTMASTER_FF
|
|
bool "ThrustMaster FireStorm Dual Power 2 support (EXPERIMENTAL)"
|
|
depends on HID_FF && EXPERIMENTAL
|
|
help
|
|
Say Y here if you have a THRUSTMASTER FireStore Dual Power 2,
|
|
and want to enable force feedback support for it.
|
|
Note: if you say N here, this device will still be supported, but without
|
|
force feedback.
|
|
|
|
config USB_HIDDEV
|
|
bool "/dev/hiddev raw HID device support"
|
|
depends on USB_HID
|
|
help
|
|
Say Y here if you want to support HID devices (from the USB
|
|
specification standpoint) that aren't strictly user interface
|
|
devices, like monitor controls and Uninterruptable Power Supplies.
|
|
|
|
This module supports these devices separately using a separate
|
|
event interface on /dev/usb/hiddevX (char 180:96 to 180:111).
|
|
|
|
If unsure, say Y.
|
|
|
|
menu "USB HID Boot Protocol drivers"
|
|
depends on USB!=n && USB_HID!=y
|
|
|
|
config USB_KBD
|
|
tristate "USB HIDBP Keyboard (simple Boot) support"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here only if you are absolutely sure that you don't want
|
|
to use the generic HID driver for your USB keyboard and prefer
|
|
to use the keyboard in its limited Boot Protocol mode instead.
|
|
|
|
This is almost certainly not what you want. This is mostly
|
|
useful for embedded applications or simple keyboards.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbkbd.
|
|
|
|
If even remotely unsure, say N.
|
|
|
|
config USB_MOUSE
|
|
tristate "USB HIDBP Mouse (simple Boot) support"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here only if you are absolutely sure that you don't want
|
|
to use the generic HID driver for your USB mouse and prefer
|
|
to use the mouse in its limited Boot Protocol mode instead.
|
|
|
|
This is almost certainly not what you want. This is mostly
|
|
useful for embedded applications or simple mice.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbmouse.
|
|
|
|
If even remotely unsure, say N.
|
|
|
|
endmenu
|
|
|
|
config USB_AIPTEK
|
|
tristate "Aiptek 6000U/8000U tablet support"
|
|
depends on USB && INPUT
|
|
help
|
|
Say Y here if you want to use the USB version of the Aiptek 6000U
|
|
or Aiptek 8000U tablet. Make sure to say Y to "Mouse support"
|
|
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
|
|
(CONFIG_INPUT_EVDEV) as well.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called aiptek.
|
|
|
|
config USB_WACOM
|
|
tristate "Wacom Intuos/Graphire tablet support"
|
|
depends on USB && INPUT
|
|
help
|
|
Say Y here if you want to use the USB version of the Wacom Intuos
|
|
or Graphire tablet. Make sure to say Y to "Mouse support"
|
|
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
|
|
(CONFIG_INPUT_EVDEV) as well.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wacom.
|
|
|
|
config USB_ACECAD
|
|
tristate "Acecad Flair tablet support"
|
|
depends on USB && INPUT
|
|
help
|
|
Say Y here if you want to use the USB version of the Acecad Flair
|
|
tablet. Make sure to say Y to "Mouse support"
|
|
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
|
|
(CONFIG_INPUT_EVDEV) as well.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called acecad.
|
|
|
|
config USB_KBTAB
|
|
tristate "KB Gear JamStudio tablet support"
|
|
depends on USB && INPUT
|
|
help
|
|
Say Y here if you want to use the USB version of the KB Gear
|
|
JamStudio tablet. Make sure to say Y to "Mouse support"
|
|
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
|
|
(CONFIG_INPUT_EVDEV) as well.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called kbtab.
|
|
|
|
config USB_POWERMATE
|
|
tristate "Griffin PowerMate and Contour Jog support"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use Griffin PowerMate or Contour Jog devices.
|
|
These are aluminum dials which can measure clockwise and anticlockwise
|
|
rotation. The dial also acts as a pushbutton. The base contains an LED
|
|
which can be instructed to pulse or to switch to a particular intensity.
|
|
|
|
You can download userspace tools from
|
|
<http://sowerbutts.com/powermate/>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called powermate.
|
|
|
|
config USB_MTOUCH
|
|
tristate "MicroTouch USB Touchscreen Driver"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use a MicroTouch (Now 3M) USB
|
|
Touchscreen controller.
|
|
|
|
See <file:Documentation/usb/mtouch.txt> for additional information.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mtouchusb.
|
|
|
|
config USB_ITMTOUCH
|
|
tristate "ITM Touch USB Touchscreen Driver"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use a ITM Touch USB
|
|
Touchscreen controller.
|
|
|
|
This touchscreen is used in LG 1510SF monitors.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called itmtouch.
|
|
|
|
config USB_EGALAX
|
|
tristate "eGalax TouchKit USB Touchscreen Driver"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use a eGalax TouchKit USB
|
|
Touchscreen controller.
|
|
|
|
The driver has been tested on a Xenarc 700TSV monitor
|
|
with eGalax touchscreen.
|
|
|
|
Have a look at <http://linux.chapter7.ch/touchkit/> for
|
|
a usage description and the required user-space stuff.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called touchkitusb.
|
|
|
|
config USB_YEALINK
|
|
tristate "Yealink usb-p1k voip phone"
|
|
depends on USB && INPUT && EXPERIMENTAL
|
|
---help---
|
|
Say Y here if you want to enable keyboard and LCD functions of the
|
|
Yealink usb-p1k usb phones. The audio part is enabled by the generic
|
|
usb sound driver, so you might want to enable that as well.
|
|
|
|
For information about how to use these additional functions, see
|
|
<file:Documentation/input/yealink.txt>.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called yealink.
|
|
|
|
config USB_XPAD
|
|
tristate "X-Box gamepad support"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use the X-Box pad with your computer.
|
|
Make sure to say Y to "Joystick support" (CONFIG_INPUT_JOYDEV)
|
|
and/or "Event interface support" (CONFIG_INPUT_EVDEV) as well.
|
|
|
|
For information about how to connect the X-Box pad to USB, see
|
|
<file:Documentation/input/xpad.txt>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called xpad.
|
|
|
|
config USB_ATI_REMOTE
|
|
tristate "ATI / X10 USB RF remote control"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use an ATI or X10 "Lola" USB remote control.
|
|
These are RF remotes with USB receivers.
|
|
The ATI remote comes with many of ATI's All-In-Wonder video cards.
|
|
The X10 "Lola" remote is available at:
|
|
<http://www.x10.com/products/lola_sg1.htm>
|
|
This driver provides mouse pointer, left and right mouse buttons,
|
|
and maps all the other remote buttons to keypress events.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called ati_remote.
|
|
|
|
config USB_KEYSPAN_REMOTE
|
|
tristate "Keyspan DMR USB remote control (EXPERIMENTAL)"
|
|
depends on USB && INPUT && EXPERIMENTAL
|
|
---help---
|
|
Say Y here if you want to use a Keyspan DMR USB remote control.
|
|
Currently only the UIA-11 type of receiver has been tested. The tag
|
|
on the receiver that connects to the USB port should have a P/N that
|
|
will tell you what type of DMR you have. The UIA-10 type is not
|
|
supported at this time. This driver maps all buttons to keypress
|
|
events.
|
|
|
|
To compile this driver as a module, choose M here: the module will
|
|
be called keyspan_remote.
|
|
|
|
config USB_APPLETOUCH
|
|
tristate "Apple USB Touchpad support"
|
|
depends on USB && INPUT
|
|
---help---
|
|
Say Y here if you want to use an Apple USB Touchpad.
|
|
|
|
These are the touchpads that can be found on post-February 2005
|
|
Apple Powerbooks (prior models have a Synaptics touchpad connected
|
|
to the ADB bus).
|
|
|
|
This driver provides a basic mouse driver but can be interfaced
|
|
with the synaptics X11 driver to provide acceleration and
|
|
scrolling in X11.
|
|
|
|
For further information, see
|
|
<file:Documentation/input/appletouch.txt>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called appletouch.
|