This patch adds IXP465 into the list of known devices and
adds IXP425 and IXP465 to the list of devices that have cfr. This
is not described in the hardware documentation, but without
it driver won't work.
Workaround (#if 1) that seemed to get rid of lost
status irqs is disabled for IXP4XX as it caused freezes
during testing of control messages. No lost irqs are
visible on IXP4XX.
Driver survived tests running over night without any
visible problems.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes compile errors when pxa2xx_udc is to be compiled
for ixp4xx platform.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes limitation which prevents use of drivers that support
speeds different that full speed.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by David Brownell, we know that IRQs are never
blocked when calling gs_close function. So the save/restore
IRQ flags are pointless.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When closing the device, the driver acquires/release twice the
port lock before/after waiting for the data to be completely
sent. Therefore it will dead lock.
This patch fixes it and also uses the generic scheduler services
for waiting for an event.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as692) fixes a few memory leaks in some unimportant error
pathways of the gadgetfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as691) fixes a few errors in the AIO interface for the
gadgetfs driver. Now requests will complete properly instead of hanging.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 board has an annoying habit of surviving soft reboots with
interrupts enabled. This patch (as674) adds a shutdown routine to the
driver so that the board can be put in a quiescent state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as671) fixes a bug in the error pathway for the net2280
probe routine. A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as669) fixes a bug in the net2280 driver. Now it will
properly send zero-length packets on ep0 until the control status stage
occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as668) fixes a typo in net2280. The handler for 0-length
control-IN requests should check that the endpoint _isn't_ halted before
sending a 0-length packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move common definitions for NET2280 to <linux/usb/net2280.h>, so that I can
use them in prism54usb (it is not merged yet, but I plan to do it soon).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be sure to record the peripheral's ep0 maxpacket size BEFORE using
that to initialize the (high speed) device qualifier; that helps a
lot with USBCV testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AT91: the two USB drivers (OHCI, UDC) got out of sync with various
usbcore and driver model PM updates; fix.
Also minor fixes to ohci: whitespace/style, MODULE_ALIAS so coldplug works
using /sys/.../modalias, and turn off _both_ clocks during suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fill OUT buffers with 0x55 before RX, so that controller driver
bugs that mangle data can be more readily detected during testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This catches up to a change in the Kconfig support for highspeed modes;
the change predated 2.6.10, and anyone using gadgetfs on a highspeed
device would see the kernel wrongly reject the alternate descriptors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some patch broke short-OUT packet handling for net2280, making it report
illegal status values. This updates the status code so it's correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I submitted the wrong version of the patch teaching about the driver
for Mentor's Highspeed Dual Role Controller (HDRC), whoops! This
uses the right name for that driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap pointed out that there now is a module_param_array_named
macro available. This patch (as666) updates g_file_storage to make use of
it. It also adds a comment listing the specifications documents used in
the design of the driver's SCSI operation (at Pat LaVarre's request).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as664) adds a comment to file_storage.c, noting that the
driver is slightly non-portable because it assumes that a buffer
allocated for a bulk-in endpoint will also be useable for a bulk-out
endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm told that some UDC hardware may work better if it knows that
receiving a short packet should always cause an error. Accordingly,
this patch (as663) sets the short_not_ok flag for bulk-out transfers in
g_file_storage. Oddly enough, there are no circumstances where that
driver can legally receive a shorter-than-expected bulk-out packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch to gadgets/net2280.[ch] which adds support for the
net2282 controller. The original code was kindly provided by PLX
Technology, I just merged it with the current net2280 driver in the
kernel. Tested on 2.6.15.6, but only with 2282. I did the merge, so
that the behaviour for the 2280 is unaffected (except for short delays
for extra checks).
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for net2282 in net2280 driver.
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch converts drivers/usb to kzalloc usage.
Compile tested with allyes config.
I think there was a bug in drivers/usb/gadget/inode.c because
it used sizeof(*data) for the kmalloc() and sizeof(data) for
the memset(), since sizeof(data) just returns the size for a pointer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows you to set the iSerialNumber field in the
usb_device_descriptor structure for your USB ethernet gadget.
It also changes the parameters shown through sysfs so they're
no longer declared as __initdata, preventing potential oopses.
That's most useful for the Ethernet addresses, which may in
some cases be random "locally administered" addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds __init section annotations to gadget driver bind() routines to
remove calls from .text into .init sections (for endpoint autoconfig).
Likewise it adds __exit section annotations to their unbind() routines.
The specification of the gadget driver register/unregister functions is
updated to explicitly allow use of those sections.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds declarations for three USB peripheral controllers:
- Two high speed USB cores that can be licensed from Mentor Graphics
to be integrated into silicon:
* "musbhsfc" is for peripherals only, as found in for example the
IBM/AMCC 44EP processors.
* "musbhdrc" is OTG-capable (dual role), and is found in various
products including OMAP 2430 and the new DaVinci SOCs.
The "musbh" standing for "Mentor USB Highspeed", the rest standing
for "Function Controller" or "Dual Role Controller" (OTG-capable).
- The full speed controller on the FreeScale MPC8272.
Adding these definitions just allows gadget driver code to handle any
controller-specific logic; controller drivers are quite separate.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resove a minor FIXME: don't change MTU while RNDIS link is active,
the other end won't expect such things...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB peripheral controller on AT91
(rm9200, eventually also sam9261 or uClinux) platforms.
More SOC support for Linux-USB ... an uncomplicated pure PIO driver.
It'd be worth using this as a model, if you're starting a driver
for some other peripheral controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote NDIS response to OID_GEN_SUPPORTED_LIST only allocated space
for the data attached to the reply, and not the reply structure
itself. This caused other kmalloc'd memory to be corrupted.
Signed-off-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a dead lock in lh7a40x udc driver. When the driver receive a
SET_FEATURE HALT request, the dev lock is taken by the interrupt
handler lh7a40x_udc_irq then the handler will call lh7a40x_set_halt
function which in its turn will try to acquire the dev lock.
Signed-off-by: Franck Bui-Huu <franck.bui-huu@innova-card.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes sure that the correct length is reported when freeing
a dma-coherent buffer; some platforms complain if that's wrong.
It also makes two parameters readonly in sysfs, as they're not
safe to change while tests are running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as622) makes gadgetfs set the "zero" flag for control-IN
responses, when the length of the response is shorter than the length of
the request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some reason alpha doesn't include <linux/dma-mapping.h> where other
architectures do; this makes net2280 include it explicitly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget drivers make no use of these, remove the pointless
comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of ARRAY_SIZE. Some trailing whitespaces are also removed.
Patch is compile-tested on i386.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as613) moves the updates to hcd->state in the dummy_hcd
driver to where they now belong. It also uses the new
HC_FLAG_HW_ACCESSIBLE flag in a way that simulates a real PCI
controller, and it adds checks for attempts to resume the bus while the
controller is suspended or to suspend the controller while the bus is
active.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as612) removes the "volatile" declarations from the
file-storage gadget. It turns out that they aren't needed for anything
much; adding a few memory barriers does a sufficient job.
The patch also removes a wait_queue. Not much point having a queue when
only one task is ever going to be on it!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It looks like that the gs_serial module maybe sleep with spinlock in gs_close.
Sometimes, system hang when I remove the gs_serial module.
From: Fengwei Yin <xaityyy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent platform_device update has reintroduced into dummy_hcd.c the
dreaded dev->dev syndrome. This harkens back to when an earlier version
of that driver included the unforgettable line:
dev->dev.dev.driver_data = dev;
This patch (as602) renames the platform_device variables to "pdev", in
the hope of reducing confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as601) adds a proper reference count to the file-storage
gadget's main data structure, to keep track of references held by child
devices (LUNs in this case). Before this, the driver would wait for
each child to be released before unbinding.
While there's nothing really wrong with that (you can't create a hang by
doing "rmmod g_file_storage </sys/.../lun0/ro" since the open file will
prevent rmmod from running), the code might as well follow the standard
procedures. Besides, this shrinks the size of the structure by a few
words... :-)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
