Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Netwinder was using gpio_xxx names which could clash with the GPIO
layer. Add a 'nw_' prefix to ensure that these remain separate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (25 commits)
em28xx: remove backward compat macro added on a previous fix
V4L/DVB (9748): em28xx: fix compile warning
V4L/DVB (9743): em28xx: fix oops audio
V4L/DVB (9742): em28xx-alsa: implement another locking schema
V4L/DVB (9732): sms1xxx: use new firmware for Hauppauge WinTV MiniStick
V4L/DVB (9691): gspca: Move the video device to a separate area.
V4L/DVB (9690): gspca: Lock the subdrivers via module_get/put.
V4L/DVB (9689): gspca: Memory leak when disconnect while streaming.
V4L/DVB (9668): em28xx: fix a race condition with hald
V4L/DVB (9664): af9015: don't reconnect device in USB-bus
V4L/DVB (9647): em28xx: void having two concurrent control URB's
V4L/DVB (9646): em28xx: avoid allocating/dealocating memory on every control urb
V4L/DVB (9645): em28xx: Avoid memory leaks if registration fails
V4L/DVB (9639): Make dib0700 remote control support work with firmware v1.20
V4L/DVB (9635): v4l: s2255drv fix firmware test on big-endian
V4L/DVB (9634): Make sure the i2c gate is open before powering down tuner
V4L/DVB (9632): make em28xx aux audio input work
V4L/DVB (9631): Make s2api work for ATSC support
V4L/DVB (9627): em28xx: Avoid i2c register error for boards without eeprom
V4L/DVB (9608): Fix section mismatch warning for dm1105 during make
...
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix module removal bugs of i82875p_edac. Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.
The problems were:
1. In module removal i82875p_remove_one() is never called.
Variable i82875p_registered is newer changed from 1, which
guarantees i82875p_remove_one() is not called (and even if it were
called, it would be called in wrong order).
As a result, the edac_mc workque is not stopped and keeps probing.
If kernel debugging options are not enabled, user may not notice
anything going wrong.
if debugging options are enabled and I do "rmmod i82875p_edac", I
get:
edac debug: edac_pci_workq_function() checking
BUG: unable to handle kernel paging request at f882d16f
...
call trace:
[<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
[<c0233974>] ? run_workqueue+0xd7/0x1a5
[<c023392f>] ? run_workqueue+0x92/0x1a5
[<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
[<c0233af9>] ? worker_thread+0xb7/0xc3
[<c0236a7b>] ? autoremove_wake_function+0x0/0x33
[<c0233a42>] ? worker_thread+0x0/0xc3
[<c0236809>] ? kthread+0x3b/0x61
[<c02367ce>] ? kthread+0x0/0x61
[<c0204587>] ? kernel_thread_helper+0x7/0x10
Fix for this is to get rid of needles variable i82875p_registered
altogether and run i82875p_remove_one() *before*
pci_unregister_driver().
2. edac_mc_del_mc() uses mci after freeing mci
edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device(). The
kobject refcount of mci drops to 0 and mci is freed. After this
mci is accessed via debug print and i82875p_remove_one() still
uses mci->pvt and tries to free mci again with edac_mc_free().
The fix for this is add kobject_get(&mci->edac_mci_kobj) after
edac_mc_alloc(). Then the mci is still available after returning
from edac_mc_del_mc() with refcount 1, and mci->pvt is still
available. When i82875p_remove_one() finally calls edac_mc_free(),
this will cause kobject_put() and mci is released properly.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26
or later, the module load fails due to BAR 0 collision. On 2.6.25 the
module loads just fine.
The overflow device on the MB seems to be hidden and its resources are not
allocated at normal PCI bus init. Log shows the missing resource problem:
EDAC DEBUG: i82875p_probe1()
PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff]
pci 0000:00:06.0: device not available because of BAR 0
[0xfecf0000-0xfecf0fff] collisions
EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow
device
The patch below fixes this by calling pci_bus_assign_resources() after
the overflow device is revealed and added to the bus. With this patch
I am again able to load and use the module.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit aef7db4bd5 fixed the problem with
recursive locking in fb blanking code if blank is caused by user setting
the /sys/class/graphics/fb*/blank. However this broke the fbcon timeout
blanking.
If you use a driver that defines ->fb_blank operation and at the same time
that driver relies on other driver (e.g. backlight or lcd class) to blank
the screen, when the fbcon times out and tries to blank the fb, it will
call only fb driver blanker and won't notify the other driver. Thus FB
output is disabled, but the screen isn't blanked.
Restore fbcon blanking and at the same time apply the proper fix for the
above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are
already called through notification from fb_blank, thus we don't have to
blank the fb again.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The engine on some radeon variants locks up if color expansion is called
for non aligned source data. This patch enables a feature of the core
fbdev to request aligned input pixmaps and uses the HW clipping engine to
clip the output to the requested size
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver. Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The netmos_9xx5_combo type assumes that PCI SSID provides always the
correct value for the number of parallel and serial ports, but there are
indeed broken devices with wrong numbers, which may result in Oops.
This patch simply adds the check of the array range.
Reference: Novell bnc#447067
https://bugzilla.novell.com/show_bug.cgi?id=447067
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 50f3beb50a fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
[libata] pata_rb532_cf: fix signature of the xfer function
[libata] pata_rb532_cf: fix and rename register definitions
ata_piix: add borked Tecra M4 to broken suspend list
Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).
Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When resizing a CQ, MTTs associated with the old CQE buffer were not
freed. As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.
Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.
Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix race condition in state change
ieee1394: fix list corruption (reported at module removal)
firewire: fw-sbp2: another iPod mini quirk entry
ieee1394: sbp2: another iPod mini quirk entry
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).
This patch adds the detection routines to recognize the different
AT91CAP9 revisions (based on the PMC subsystem version number), and
uses them to:
- activate a workaround for the external interrupts levels
(on revB CPUs)
- set the UDPHS_BYPASS bit (on revB CPUs)
- set AT91_GPBR register address to the correct offset
(0xfffffd50 on revB, 0xfffffd60 on revC)
For debugging usage, the CPU revision can be found in /proc/cpuinfo
on the 'Revision' line.
This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch)
where it has been tested for the last 6 months.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Apple ALU wireless keyboards are bluetooth devices
HID: remove setup mutex, fix possible deadlock
HID: add USB ID for another dual gameron adapter
HID: unignore mouse on unibody macbooks
HID: fix blacklist entries for greenasia/pantherlord
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: serial: add more Onda device ids to option driver
USB: usb-storage: unusual_devs entry for Nikon D2H
USB: storage: unusual_devs entry for Mio C520-GPS
USB: fsl_usb2_udc: Report disconnect before unbinding
USB: fsl_qe_udc: Report disconnect before unbinding
USB: fix SB600 USB subsystem hang bug
Revert "USB: improve ehci_watchdog's side effect in CPU power management"
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
