Without this patch a Opteron test system here oopses at boot with
current git.
Calling to_pci_dev() on a NULL pointer gives a negative value so the
following NULL pointer check never triggers and then an illegal address
is referenced. Check the unadjusted original device pointer for NULL
instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://linux-nfs.org/~bfields/linux:
SUNPRC: Fix printk format warning
nfsd: clean up svc_reserve_auth()
NLM: don't requeue block if it was invalidated while GRANT_MSG was in flight
NLM: don't reattempt GRANT_MSG when there is already an RPC in flight
NLM: have server-side RPC clients default to soft RPC tasks
NLM: set RPC_CLNT_CREATE_NOPING for NLM RPC clients
Since we may not have a pci_dev for the device we need to access, we can't
use pci_read_config_word. But raw_pci_read is an internal implementation
detail; it's better to use the architected pci_bus_read_config_word
interface. Using PCI_DEVFN instead of a mysterious constant helps
reassure everyone that we really do intend to access device 8.
[ Thanks to Grant Grundler for pointing out to me that this is exactly
what the write immediately above this is doing -- enabling device 8 to
respond to config space cycles.
- Matthew
Grant also says:
"Can you also add a comment which points at the Intel
documentation?
The 'Intel E7320 Memory Controller Hub (MCH) Datasheet' at
http://download.intel.com/design/chipsets/datashts/30300702.pdf
Page 69 documents register F4h (DEVPRES1).
And I just doubled checked that the 0xf4 register value is
restored later in the quirk (obvious when you look at the code
but not from the patch"
so here it is.
- Linus ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 813a0eb233
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 09 February 2008, Adrian Bunk wrote:
> Commit 9e016a7192 causes the following
> compile error:
>
> <-- snip -->
>
> ...
> CC drivers/ide/arm/bast-ide.o
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c: In function 'bastide_register':
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:31: error: 'hwif' redeclared as different kind of symbol
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:29: error: previous definition of 'hwif' was here
> make[4]: *** [drivers/ide/arm/bast-ide.o] Error 1
>
> <-- snip -->
Remove 'ide_hwif_t **hwif' argument from bastide_register()
(together with write-only ifs[]).
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
rq->cmd[0] is never set to REQ_IDETAPE_READ_BUFFER so remove
REQ_IDETAPE_READ_BUFFER handling from idetape_create_write_cmd()
and the define itself.
Then remove no longer used idetape_create_read_buffer_cmd()
and IDETAPE_RETRIEVE_FAULTY_BLOCK define.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 03 January 2008, Robert Hancock wrote:
[...]
> How about getting rid of this stupid thing in drivers/ide/ide.c:
>
> #define REVISION "Revision: 7.00alpha2"
>
> which is used in:
>
> printk(KERN_INFO "Uniform Multi-Platform E-IDE driver " REVISION "\n");
>
> It's been 7.00alpha2 for god knows how long, so clearly this version
> number is not useful..
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Probe port _after_ it is fully initialized.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't set 'restore' flag for ide_unregister() when initializing new
interface.
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 909f4369bc ]
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert palm_bk3710 host driver to use ide_device_add() instead of
ide_register_hw() (while at it drop doing "ide_unregister()" loop which
tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 9e016a7192 ]
* Rename 'ide_ctlr_info' to 'hw' and 'index' to 'i' while at it.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the check for hwgroup->handler and printk(KERN_CRIT, ...) at the start
of __ide_set_handler() with mere BUG_ON() while removing such from the caller,
ide_execute_command(). Fix up the code formatting, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale comment from the cs5520 IDE driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I have reviewed all blk-end-request patches again to confirm whether
there are any similar problems with the last week's ide-cd panic:
http://lkml.org/lkml/2008/1/29/140
And I found a possible similar bug in ide-io change:
ide_end_drive_cmd() could be called for blk_pc_request() which could
have bios. To complete such requests correctly, we need to pass
the actual size of the request.
Otherwise, __blk_end_request() returns 1 because the request still has
bios, and the system will BUG() unnecessarily.
The following patch fixes the bug and should be applied on top of
Linus' git.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
net/sunrpc/xprtrdma/svc_rdma_sendto.c:160: warning: format '%llx'
expects type 'long long unsigned int', but argument 3 has type 'u64'
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This is a void function attempting to return the return value from
another void function, which seems harmless but extremely weird, and
apparently makes some compilers complain.
While we're there, clean up a little (e.g. the switch statement had a
minor style problem and seemed overkill as long as there's only one
case).
Thanks to Trond for noticing this.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
It's possible for lockd to catch a SIGKILL while a GRANT_MSG callback
is in flight. If this happens we don't want lockd to insert the block
back into the nlm_blocked list.
This helps that situation, but there's still a possible race. Fixing
that will mean adding real locking for nlm_blocked.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
With the current scheme in nlmsvc_grant_blocked, we can end up with more
than one GRANT_MSG callback for a block in flight. Right now, we requeue
the block unconditionally so that a GRANT_MSG callback is done again in
30s. If the client is unresponsive, it can take more than 30s for the
call already in flight to time out.
There's no benefit to having more than one GRANT_MSG RPC queued up at a
time, so put it on the list with a timeout of NLM_NEVER before doing the
RPC call. If the RPC call submission fails, we requeue it with a short
timeout. If it works, then nlmsvc_grant_callback will end up requeueing
it with a shorter timeout after it completes.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Now that it no longer does an RPC ping, lockd always ends up queueing
an RPC task for the GRANT_MSG callback. But, it also requeues the block
for later attempts. Since these are hard RPC tasks, if the client we're
calling back goes unresponsive the GRANT_MSG callbacks can stack up in
the RPC queue.
Fix this by making server-side RPC clients default to soft RPC tasks.
lockd requeues the block anyway, so this should be OK.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
It's currently possible for an unresponsive NLM client to completely
lock up a server's lockd. The scenario is something like this:
1) client1 (or a process on the server) takes a lock on a file
2) client2 tries to take a blocking lock on the same file and
awaits the callback
3) client2 goes unresponsive (plug pulled, network partition, etc)
4) client1 releases the lock
...at that point the server's lockd will try to queue up a GRANT_MSG
callback for client2, but first it requeues the block with a timeout of
30s. nlm_async_call will attempt to bind the RPC client to client2 and
will call rpc_ping. rpc_ping entails a sync RPC call and if client2 is
unresponsive it will take around 60s for that to time out. Once it times
out, it's already time to retry the block and the whole process repeats.
Once in this situation, nlmsvc_retry_blocked will never return until
the host starts responding again. lockd won't service new calls.
Fix this by skipping the RPC ping on NLM RPC clients. This makes
nlm_async_call return quickly when called.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
.. and I really need to call it something else. Maybe it is time to
bring back the weasel series, since weasels always make me feel good
about a kernel.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
...
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Loic Prylli <loic@myri.com>, who originally proposed
this idea.
Always using legacy configuration mechanism for the legacy config space
and extended mechanism (mmconf) for the extended config space is
a simple and very logical approach. It's supposed to resolve all
known mmconf problems. It still allows per-device quirks (tweaking
dev->cfg_size). It also allows to get rid of mmconf fallback code.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8811930dc7 ("splice: missing user
pointer access verification") added the proper access_ok() calls to
copy_from_user_mmap_sem() which ensures we can copy the struct iovecs
from userspace to the kernel.
But we also must check whether we can access the actual memory region
pointed to by the struct iovec to fix the access checks properly.
Signed-off-by: Bastian Blank <waldi@debian.org>
Acked-by: Oliver Pinter <oliver.pntr@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 954415e33e ("[PKT_SCHED] ematch:
tcf_em_destroy robustness") removed a cast on em->data when
passing it to kfree(), but em->data is an integer type that can
hold pointers as well as other values so the cast is necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
hrtimer_nanosleep_restart() clears/restores restart_block->fn. This is
pointless and complicates its usage. Note that if sys_restart_syscall()
doesn't actually happen, we have a bogus "pending" restart->fn anyway,
this is harmless.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Pavel Emelyanov <xemul@sw.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Toyo Abe <toyoa@mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Spotted by Pavel Emelyanov and Alexey Dobriyan.
compat_sys_nanosleep() implicitly uses hrtimer_nanosleep_restart(), this can't
work. Make a suitable compat_nanosleep_restart() helper.
Introduced by commit c70878b4e0
hrtimer: hook compat_sys_nanosleep up to high res timer code
Also, set ->addr_limit = KERNEL_DS before doing hrtimer_nanosleep(), this func
was changed by the previous patch and now takes the "__user *" parameter.
Thanks to Ingo Molnar for fixing the bug in this patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Pavel Emelyanov <xemul@sw.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Toyo Abe <toyoa@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Spotted by Pavel Emelyanov and Alexey Dobriyan.
hrtimer_nanosleep() sets restart_block->arg1 = rmtp, but this rmtp points to
the local variable which lives in the caller's stack frame. This means that
if sys_restart_syscall() actually happens and it is interrupted as well, we
don't update the user-space variable, but write into the already dead stack
frame.
Introduced by commit 04c227140f
hrtimer: Rework hrtimer_nanosleep to make sys_compat_nanosleep easier
Change the callers to pass "__user *rmtp" to hrtimer_nanosleep(), and change
hrtimer_nanosleep() to use copy_to_user() to actually update *rmtp.
Small problem remains. man 2 nanosleep states that *rtmp should be written if
nanosleep() was interrupted (it says nothing whether it is OK to update *rmtp
if nanosleep returns 0), but (with or without this patch) we can dirty *rem
even if nanosleep() returns 0.
NOTE: this patch doesn't change compat_sys_nanosleep(), because it has other
bugs. Fixed by the next patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Pavel Emelyanov <xemul@sw.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Toyo Abe <toyoa@mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
include/linux/hrtimer.h | 2 -
kernel/hrtimer.c | 51 +++++++++++++++++++++++++-----------------------
kernel/posix-timers.c | 14 +------------
3 files changed, 30 insertions(+), 37 deletions(-)
clocksource initialization and error accumulation. This corrects a 280ppm
drift seen on some systems using acpi_pm, and affects other clocksources as
well (likely to a lesser degree).
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
htb_requeue() enqueues skbs for which htb_classify() returns NULL.
This is wrong because such skbs could be handled by NET_CLS_ACT code,
and the decision could be different than earlier in htb_enqueue().
So htb_requeue() is changed to work and look more like htb_enqueue().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the explicit usage of the magic constant "1024"
with IP6_RT_PRIO_USER in the IPV6 tree.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/starfire.c:219: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/typhoon.c:137: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x19723): Section mismatch in reference from the function ISACVersion() to the variable .devinit.data:ISACVer
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2005b): Section mismatch in reference from the function setup_avm_a1_pcmcia() to the function .devinit.text:setup_isac()
ISACVer were only used from function annotated __devinit
so add same annotation to ISACVer.
One af the fererencing functions missed __devinit so add it
and kill an additional warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x722): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_teles3()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x72c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_s0box()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x736): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_telespci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x747): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_avm_pcipnp()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x74e): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_elsa()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x755): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_diva()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x75c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sedlbauer()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x763): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_s()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x76a): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcpci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x771): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcsx()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x778): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_niccy()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x77f): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_bkm_a4t()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x786): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sct_quadro()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x78d): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_gazel()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x794): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_w6692()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x79b): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_u()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x7a2): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_enternow_pci()
checkcard() are the only user of hisax_cs_setup_card().
And checkcard is only used during init or when hot plugging
ISDN devices. So annotate hisax_cs_setup_card() with __devinit.
checkcard() is used by exported functions so it cannot be
annotated __devinit. Annotate it with __ref so modpost
ignore references to _devinit section.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
