The file, tuner-driver.h was originally named tuner-hw.h, but we decided to
rename it. At the time, I had forgotten to change the #ifdef __TUNER_HW_H__
to #ifdef __TUNER_DRIVER_H__ . This patch corrects that.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add DVB-T support for Avermedia Super 007
Analog television is untested. The device lacks input adapters for radio,
svideo & composite -- seems to be a DVB-T ONLY device.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a simple whitespace cleanup.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The revision is part of the pci_dev struct, so there is no need to read it in.
Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.
linux/pci.h wasn't included. It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
channels_min should be 2, not 1. The hardware only supports stereo.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get. One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on. Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.
Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on. However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug). The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.
Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an irq handled by the cx88 core driver (currently IR and errors) occurs
and the cx88-alsa irq handler is the first called, it will claim to have
handled the irq but it doesn't call cx88_core_irq() to handle it.
The means loading cx88-alsa can disable the IR remote.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used for the PCI_INTMSK and PCI_INT_STAT registers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add VIDIOC_OVERLAY to enable/disable the OSD. Also add the OSD state to the
log status report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of ivtv_udma_fill_sg_list() was changed by the
highmem bugfix, but that return value was still used in ivtv-yuv.c.
Revert to the old return value, but in addition return -1 in case of
a memory allocation error.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When trying to DMA userspace buffers to the cx23415 you need to check
whether the page is in highmem. If this is the case, then bounce buffers
have to be used to allow DMA.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Serialization is now done on the open/close/ioctl level and also when the
read/write/poll start an encoder/decoder stream.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add FILE debug flag for open/close/read/write/poll.
- show cmd for encoder/decoder command ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some streams (PCM, VBI decoding) do not need that much memory, so specify
the allocated memory in kB instead of MB to limit memory usage. E.g. 1 MB
is overkill for the VBI decoding stream, 64 kB is enough.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TV output standard was set only on first use, which meant that the saa7127
was set to NTSC until then, leading to flickering on PAL systems.
Since the saa7127 has no firmware it is OK to initialize it immediately.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Whenever the 0x80b register is used the microcontroller should be reset.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Give up frame after three retries.
- When the last capture/decode ends, make sure to delete the dma_timer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Invalid VBI packets should result in an empty VBI frame, not
in an zero-sized frame that causes the reader to incorrectly
return a 0 (EOF) value.
- PIO completion should not reset the sg_pending_size field.
- The DMA offset detection code should be ignored for PIO transfers:
it somehow messes up the data on the card and is not needed anyway
for PIO.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out that the cx23415/6 DMA engine cannot do scatter/gather DMA
reliably. Every so often depending on the phase of the moon and your
hardware configuration the cx2341x DMA engine simply chokes on it and
you have to reboot to get it working again.
This change replaced the scatter/gather DMA by single transfers at a time,
where the driver is now responsible for DMA-ing each buffer.
UDMA is still done using scatter/gather DMA, that will be fixed soon.
Many thanks to Mark Bryars <mark.bryars@etvinteractive.com> for discovering
the link between scatter/gather and the DMA timeouts.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When there are no more free buffers, then buffers are stolen from the
predma queue. Buffers should be stolen from the head of that queue (which
is where the most recently added buffers are) and all buffers belonging
to a frame should be stolen. Otherwise 'half-frames' would remain in the
queue, which leads to ugly playback and complete sync failure for YUV
buffers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The CX2341X_ENC_INITIALIZE_INPUT firmware call requires careful handling,
otherwise the computer can freeze or the top-third of the screen can start
flickering. This patch ensures that CX2341X_ENC_INITIALIZE_INPUT is called
at the right time and in the right way.
In addition the stop capture handling was improved so that the last pending
DMA transfer is also processed. Otherwise this would be the first data that
arrived when a new capture was started which is not what you want.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Working with Nova-T Stick (70001) with remote control model A415.
Untested with other dib0700m/dib0700p devices.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typo fix in Nova-TD description
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are now 4 different versions of the GENPIX USB adapter. The
newest 'Skywalker' models are fully self-contained, and need no
additional hardware to be used. A very reliable DVB-S card even without
using any of the alternate modulatations (which this kernel module does
not currently support)
The following patch adds support for all 4 versions of the genpix
adapter (www.genpix-electronics.com).
Signed-off-by: Alan Nisota alannisota@gmail.com
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise. The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.
However, the "no deemphasis" setting doesn't work. On my chip, cx23883, it
produces the same result as the 75 us time constant. Maybe the default
settings on the cx23881 are for 50 us?
Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The first part of dvb_net_close() is just a cut&paste from
dvb_generic_release(), so maybe it would be better to just call
dvb_generic_release() instead?
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker spotted that we'd have already oops'ed if "dev"
was NULL.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the "CORE" prefix from cx88 printks. It was only used a few times,
and it makes it look like they're coming from the kernel core or something.
Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it. Get rid of the addresses, which are always
wrong. The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.
In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.
Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.
The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.
A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized. Moving that task to cx88-cards makes the
driver simpler and the files more self contained.
- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
moved out of cx88-core.c:cx88_get_core() and into a new function in
cx88-cards.c, cx88_core_create(). This makes both functions simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx88 driver state stored the ID of the board type in core->board. Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.
This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information. This allows
access to board information without the extra indirection. e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.
This has a number of advantages:
- The code is simpler to write.
- It compiles to be smaller and faster, without needing the extra array lookup
to get at the board information.
- The cx88_boards array no longer needs to be exported to all cx88 modules.
- The boards array can be made const
- It should be possible to avoid keeping the (large) cx88_boards array around
after the module is loaded.
- If module parameters or eeprom info override some board configuration
setting, it's not necessary to modify the boards array, which would
affect all boards of the same type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An error message for PCI resource allocation failure used the board type
before it was set. Just get rid of the error message, as get_ressources()
[sic] already prints one. Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux setting is only two bits, but was taking up a whole 32
in the input description struct. By changing it to a two-bit
bitfield, it can fit in what was padding space before and drop
the input size by 4 bytes, from 28 to 24. This drops the board
description struct, which has 9 inputs, from 280 to 244 bytes.
Total driver size decreases by 2108 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The currently used "struct class_device" will be removed from the
kernel. Here is a trivial patch that converts DVB to use struct device.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change io_st_le32() to use inline functions rather than
direct inline assembly code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-simple is the only sub-driver that uses last_div, so we
can free up two bytes of memory for all other tuners, by moving
this into tuner-simple's private data area.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some lines later filp->private_data is initialized to dev again.
Since there are some checks that might fail in the mean time
keep the later version.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly attribute the origin of the driver to Kazuhiko
Kawakami.
It took some time to get the S-O-B line from the original
tvaudio patch author, but here it is.
Signed-off-by: Kazuhiko Kawakami <kazz-0@mail.goo.ne.jp>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When changing channels the audio has to be muted. This is done
by calling CX2341X_ENC_MUTE_AUDIO and by muted the audio input.
The latter is not necessary and is now removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio muting for the tuner input was implemented by stopping the
audio microcontroller and restarting it on unmute. However, it
appears that this method can actually crash the audio firmware.
It's rare and seems to happen with NTSC only.
It has been reimplemented by setting to volume to 0. In addition, the
reporting of the mute state has been improved as well: it used to be
impossible to detect whether the audio was muted by the user or if it
was muted due to the microcontroller trying to detect the audio
standard. This is now clearly stated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Split Club3D card from Yuan PG600-2, GotView PCI DVD Lite
(different composite input)
- Add AVerTV MCE 116 Plus (M116) card
- Allow Xceive cards to be used without Xceive support
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support to optionally reset the IR and/or the video digitizer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Resetting without reloading the firmware is not enough. Sometimes the
firmware is 'stuck' and needs to be reloaded.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the addition of these ioctls, I'm able to watch TV with a 32-bit version
of tvtime on x86_64.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since videobuf_waiton is called with intr=1, it can return -EINTR and therefore
err may be non-zero. This happens when the system goes into the standby state.
Without the BUG() occurring, there's no problem with standby mode while DVB
is being used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Interrupt processing fixed: First handle interrupt, then acknowledge it.
Otherwise the same interrupt might occur twice.
Cleaned-up i2c interrupt handler and i2c error messages.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The calculation of frequency limits ignored tuner-specific frequency limits.
Range checks and GET_INFO ioctl updated accordingly.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The min frequencies of the DVB-C frontends are wrong.
In Europe, the center frequency of the lowest channel is 50.5MHz and not
51MHz. All known cards with the stv0297/tda0002x/ves1820 frontend are
able to tune to this frequency.
I've changed the range to the lowest channel - 1/2 bandwidth and the
highest channel + 1/2 bandwidth. For the design of the dvb driver, the
frequency ranges must be part of the tuner and not of the frontend
itself. The same frontend may be used for different tuners.
The attached patch does only fix the ranges and not the design.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA8083 supports a symbol rate from 12..30 MSym/s.
The Grundig 29504-451 tuner uses the TDA8060 down-converter,
which has a frequency range from 920..2200MHz.
Thanks-to: Lars Buerding <lindvb@metatux.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add radio support for the Thomson DTT7612 tuner.
This tuner uses a different 1st intermediate frequency than the other radio
tuners supported (a lot of NTSC radio tuners probably need this change too).
Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for
radio reception. The radio frequency setting code in tuner-simple now uses
this field, instead of a special case select() block for each tuner with radio
support.
The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1
in tuner-types.c.
The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and
fm_gain_normal = 1.
Add some defines for tda9887 bits that control IF setting in radio mode.
Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz
radio IF.
Fix the way tda9887 radio options work. The driver was modifying the default
radio mode config templates based on the TDA9887_XXXX flags. This means that
_all_ tuners would get the same settings. If you had a one tuner than used
TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the
tda9987 driver just checks if tuner mode is radio and then applies the config
settings directly to the data being sent, just like how all the TV mode
settings already work.
The PLL setting math is made a little more accurate.
And a grammar error in a printk is fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the advanced debug functions to the radio videodev template. One could
already use them from the video and vbi devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a card driver is compiled into the kernel and mt2131 or s5h1409 are
compiled as modules, the kernel won't link.
A compiled in driver can't use a module, so in this case the mt2131 or s5h1409
are effectively disabled w.r.t the compiled in driver and the stub attach
function should be used.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the current driver, the field order is global. As soon as it's changed it
takes immediate effect. This is a problem when the video changes order mid
stream. Although it mostly works okay, the video may judder / flicker.
This patch attaches the field order to the frame, so that any buffered frames
will not be displayed until the correct field. In the event that the field
order is changed mid stream, the driver will ensure that the previous frame
is displayed for a minimum of 3 fields. These are the two original fields the
frame should have occupied, plus the one extra since the new frame still has
to wait for the correct field.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The yuv output code always compares the new frame position & size with those
of the previous frame. If they are different, a flag is set to request the
yuv output registers be updated when the new frame is displayed.
If the incoming frames are delivered too fast, exhausting the buffers, the
most recent frame already buffered will be discarded. Unfortunately, any
update request will also be discarded. If the new frame matches the size &
position of the now discarded frame, the yuv registers are not flagged for
update & will remain in their old state.
This patch preserves the register update flag in the event that a frame is
dropped.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Framebuffer timings are currently locked to the video format in use when the
module is loaded. If the video format is then changed, the timings returned
by the framebuffer will be for the original format.
This patch ensures that the timings returned reflect the current video format.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the video standard is changed, there's no guarantee the framebuffer
dimensions are still legal. The yuv output code uses these dimensions to
calculate the size & position for the video overlay. If the framebuffer
dimensions are now illegal, the output may exceed the vertical limit of the
display, causing distortion.
This patch adds an additional check to ensure the output doesn't exceed
the limits for the current video standard, cropping if required.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker spotted that we have already oops'ed if "fe" was NULL.
Since "fe" being NULL seems impossible at this point this patch removes
the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The new firmware returns the data of the REQUEST_POLL_RC request in
reversed order. The default is RC5, but it can be adjusted using a
module parameter.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Matt Doran I found that there the module parameter description
was not OK.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
line-breaks in dib0700-remote-query function fixed.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forgot to initialize the timf_default field.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In some areas in the world the broadcasters are not using the same
cellid for each transmitter in a SFN. The DiBcom has problems with
that setup. The module parameter buggy_sfn_workaround makes it re-usable.
Signed-off-by: Matt Doran <matt.doran@papercut.biz>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix for size of remote control keys in DiB0700.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support Compro VideoMate 500 with DiB7000PC. Another design of
Compro uses the DiB7000PC and it has new USB ids.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds remote control support for the Hauppauge Nova-T 500
using the same keys as for STK7700PD.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset adds support for DiB7070P-based devices by adding the
dib0070-driver and putting the appropriate layouts into
dib0700_devices.c
It also includes a new firmware for the dib0700 which is necessary to
make the DiB7070-boards work and it also should fix the i2c-problems
on some boards.
Signed-off-by: Jean-Philippe Sibers <jpsibers@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changesets syncs the OpenSource driver for DiBcom demodulators
with version 2.1.3 of DiBcom reference driver. There were some
improvements since the last release for linux-dvb, e.g.:
- stepped AGC startup
- less space for initialization
- diversity synchronization
Furthermore this changeset contains the following things:
- latest AGC settings for MT2266-based devices (namely Nova-TD and other) will improve the sensitivity
- support for STK7700D reference design in dib0700-devices
- remove some line-breaks when debugging is enabled
- getting rid of layer between frontend_parameters and ofdm_channel used in dib*-drivers
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the Samsung S5H1409 demodulator, also known
as the Conexant CX24227 demodulator. 8VSB mode has been tested and QAM
has been implemented based on the spec, although it's untested.
The S5H1409 / CX24227 appears on various Hauppauge boards.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for the Microtune MT2131 tuner. 8VSB mode has been
tested but QAM support will likely require more register work. Hauppauge
have not announced any QAM devices using the MT2131 so QAM remains
undone.
For legal reasons, Microtune allowed us to write a GPL driver providing
we did not document in significant detail any of the registers. This
explains the lack of comments or defined on register names.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The DVB frontend tuning interface uses a semaphore as mutex. Use the
mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch replaces an array size calculation done using sizeof
with an invocation of the ARRAY_SIZE macro.
Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.
Signed-off-by: Andi Drebes <lists-receive@programmierforen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch replaces an array size calculation done using sizeof
with an invocation of the ARRAY_SIZE macro.
Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.
Signed-off-by: Andi Drebes <lists-receive@programmierforen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove incorrect range check of symbol rate, spotted by the coverity
checker and reported by Adrian Bunk.
These range checks are performed by dvb_core now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add range check of frequency and symbol rate to the FE_SET_FRONTEND ioctl.
This will also avoid a divide-by zero exception in the stv0297 driver,
if symbol rate is set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert av7110_v4l.c to use i2c_transfer() instead of saa7146_i2c_transfer().
Make saa7146_i2c_transfer() static.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is internal to the Panasonic VP27S tuner and is used to set
the mono/stereo/bilingual setting of the tuner.
It is used by two Japanese cx23416-based cards.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The firmware is now loaded when the driver is actually used for the first
time. This allows the driver to be compiled in-kernel instead of as a module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add initial support for Dual-DVB-T stick based on DiB7700 and MT2266
- Microtune MT2266 driver.
- Preliminary support for these dual tuner devices :
- Pinnacle Dual DVB-T diversity
- Terratec Cinergy DT USB XS diversity
- Hauppauge Nova TD USB
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up duplicate includes in
drivers/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add code for autodetection and firmware download to the Miglia TVMini USB
DVB-T adapter. After firmware download, the device re-registers using
the WT220U_ZL0353_WARM usb id.
Signed-off-by: Rasmus Rohde <rohde@duff.dk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add permissions to all the module parameters so they can be queried and set
(when possible) via sysfs.
Add description for the vidmem parameter.
Change the video_nr parameter to an array, so that the video number can be
specified when a user has more than one card. The driver would try to give
all cards the same number otherwise, which will fail for all cards after the
first.
The default_input option would only allow values of 0 or 1, contrary to the
description. Allow values up to the number of inputs defined for the card.
Add description of lock_norm's different behavior for 1 and >1.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Debugging cleanups to the zr36067 driver:
* Use module_param_named() to declare the debug parameter, so we can
use a single global variable to handle the debug level. This makes
the driver a bit smaller (by 648 bytes on x86_64), thanks to one
less level of indirection on every use.
* Change the debug parameter sysfs permissions, so that the debug
level can be adjusted at runtime, as is done in many other
media/video drivers.
* The debug level is between 0 and 5, not 0 and 4.
* Move the zr_debug export and dprintk macro definition to a header
file so that we don't have to define them in each source file.
* Simplify a duplicate test on zr_debug.
Note that zr_debug was subsequently renamed to debug_zr36067 to avoid
possible conflicts with other Zoran device drivers, on a suggestion
by Trent Piepho.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a compile warning on non-32-bit machines in v4l2-int-device.h.
Add internal ioctl interface fallback function for ioctls with one
argument.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a driver for Toshiba TCM825x VGA camera sensor. This sensor is used
e.g. in Nokia N800 internet tablet.
This driver uses the new V4L2 internal ioctl interface.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds an internal ioctl-like interface which can be used in
situations where a single Video4Linux device is implemented by multiple
device drivers. One master device controls one or more slave devices.
The slaves provide Video4Linux ioctl-like interface for the use of the
master.
Only a handful of ioctls are implemented at the moment. More can (and
should) be added as more functionality is required.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using udma yuv causes the driver becomes locked into that mode. This prevents
use of the mpeg decoder & non-udma yuv output. This patch clears the
operating mode when the device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
duplicated .mmap in one, .vidioc_s_audio misspelled as .vidioc_g_audio
in other
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a couple drivers that do not correctly terminate their pci_device_id
lists. This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: Kees Cook <kees@ubuntu.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: With a hardware encoder board installed as cx88[1] and a
non-encoder boards installed as cx88[0], an OOPS is generated
during cx8802_get_device() called from mpeg_open().
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7191.c: In function 'saa7191_probe':
saa7191.c:596: warning: passing argument 3 of
'saa7191_write_block' discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 85237f202d introduced the
following warning (with CONFIG_USB_PWC_DEBUG=y):
drivers/media/video/pwc/pwc-if.c: In function "pwc_video_close":
drivers/media/video/pwc/pwc-if.c:1211: warning: "i" may be used uninitialized in this function
This is true, and can cause a broken debug message to be logged.
Here's a fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now the composite sound input doesn't work on AverTV 307 because of
the wrong mux setup. The composite sound is routed via an external
4channel multiplexer controlled by GPIO, while the code assumes an internal
multiplexer instead.
Presumably this was a copy/paste error, and noone have ever tested the
functionality.
With the attached patch it works properly, which gives me an ability to
finally watch the cable TV under linux.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a documentation bug (the type mask is 3 bits long, not 2) the wrong
frame types were filled in: the B and P frame types were swapped.
This bug also hid a second bug: when a capture is stopped a last entry is
written into the pgm index buffer with internal type 0, denoting the end
of the program. This entry wasn't ignored, instead it was accidentally
returned to the caller as a P frame.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
static function dvb_net_sec declares input arg "pkt" as u8. However, the
same argument at dvb_net_sec_callback is defined as "const u8". When
calling dvb_net_sec, this is casted as just "u8".
gcc 4.2.1 generates a warning about that:
CC [M] drivers/media/dvb/dvb-core/dvb_net.o
drivers/media/dvb/dvb-core/dvb_net.c: In function "dvb_net_sec_callback":
drivers/media/dvb/dvb-core/dvb_net.c:905: warning: passing argument 2 of
"dvb_net_sec" discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Git changeset 6bdcc6e6db dropped the
stand-alone lgh06xf module, whose functionality was absorbed into the
dvb-pll module. However, there was a minor difference between the code
in lgh06xf and dvb-pll, which caused a regression in b2c2-flexcop
devices using the LG-H06xF NIM.
dvb-pll will probe for the presence of an i2c pll chip by performing a
single byte read, the lgh06xf driver did not do this. Unfortunately, the
code in flexcop-i2c.c does not currently support 1 byte or 0 byte reads
as a probe. Such probes with the current code will always fail.
In order to work around this problem, and restore proper functionality
of the Airstar HD5000 device, this hack was created to make the probe
appear to succeed. The single byte read in dvb_pll_attach is the only
place where such a probe would ever occur, so this change is safe, and
will not affect any other devices.
Of course, if one knew how to actually perform the read operation, it
would be better to go that route. In the meantime, however, we must
apply this workaround, in order to prevent the regression that causes
tuning to fail on the Airstar HD5000 ATSC device.
Thanks to Jarod Wilson, who had originally reported this regression, and
to Geoffrey Hausheer, whose original workaround patch led us to find the
actual cause of the problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Geoffrey Hausheer <inli3epy93n@phracturedblue.com>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
the pwc driver has a disconnect method that waits for user space to
close the device. This opens up an opportunity for a DoS attack,
blocking the USB subsystem and making khubd's task busy wait in
kernel space. This patch shifts freeing resources to close if an opened
device is disconnected.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If, in em28xx_usb_probe() the memory allocation
dev->alt_max_pkt_size = kmalloc(32*
dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.
This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Configuring the OLPC camera requires something over 150 register
writes. Unfortunately, querying the CAFE i2c controller too
soon after a write causes the hardware to flake. The problem had
been "solved" with an msleep() call, but, between the number of
registers and how msleep() behaves, that resulted in a 3-second
delay on camera initialization. Instead, we hand-code a wait for
the completion interrupt which avoids reading the status registers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner maximum frequency wasn't being set, while the minimum
frequency was set to what the maximum should have been.
If a future patch were to enforce these limits, dvb-pll would be
effectively broken.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv: fix VIDIOC_S_FBUF support: new OSD values where never actually set.
The values set with VIDIOC_S_FBUF were not actually used until the next
VIDIOC_S_FMT. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The fcv1236d support patch was created before the "dvb: remove static
dependencies on dvb-pll" patch was applied, but the fcv1236d patch didn't
get merged until after the fact.
struct dvb_pll_fcv1236d can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch:
- adds a missing error check and
- removes an error check that could never be true
Both spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the useless tuner field and avoids a double free of
the tuner (either mt2060 or qt1010).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.
This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The drivers reads the PCI subsystem ID into its state structure, but it's
never used anywhere.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch adds checking of kthread_run return code and issues a message
if it fails.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If v4l2_ctrl_next is called without the V4L2_CTRL_FLAG_NEXT_CTRL then it
should check whether the passed control ID is valid and return 0 if it
isn't. Otherwise a for-loop over the control IDs will never end.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VBI DMA is handled in a special way and is marked with a bit.
However, that bit was set at the wrong time and could be cleared
by mistake if a PCM (or other) DMA request would arrive before the
VBI DMA was completed. So on completion of the VBI DMA the driver
no longer knew that that DMA transfer was for VBI data. And this
in turn caused havoc with the card's DMA engine.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Driver prints banner including kernel version. Was a leftover from when
the driver was standalone.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C_ALGOBIT must also be selected when ivtv is selected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Turn off debugging of API commands that occur during encoding or decoding,
unless they are explicitly requested.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Parse error in ifdef or bad use of macro.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Replace assignments to "current->state" with the preferred calls to
schedule_timeout_interruptible().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for high volume debug messages, allowing them to be turned
on selectively.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Starting an MPEG and VBI capture simultaneously caused errors in
the VBI setup: this setup was done twice when it should be done
only for the first stream that is opened.
Added a mutex to prevent this from happening.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tune() dvb_frontend callback changed delay signess:
int (*tune)(struct dvb_frontend* fe,
struct dvb_frontend_parameters* params,
unsigned int mode_flags,
- int *delay,
+ unsigned int *delay,
This change caused warnings on cx24123 and dst modules:
/home/v4l/master/v4l/cx24123.c:1034: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1782: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1808: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1837: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1860: warning: initialization from incompatible pointer type
This patch corrects the function prototype on both modules to follow the
core change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Re-initialize aspect ratio and pan scan after arm crash.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make some pointers const, and then delete some now unnecessary casts,
which were the wrong signedness anyway, being used to strip the const
from another pointer.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
New code is simpler, shorter, compiles to about half the size, and is 2
to 4 times faster depending on how many bits in the mask are set.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Better way of creating and loading the firmware used.
Update for get_dvb_firmware script to extract the files for opera usb-box
Help file for creating the firmware added
Signed-off-by: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added GemTek USB radio and removed experimental dependency.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- usbvision_muxsel simplified, now uses some well known constants.
- since the decoder needs to change input norm, call to muxsel added when
changing video standard.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Dwaine Garden <DwaineGarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Alter the tuner type for the WinTV USB UK PAL model.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Hauppauge WinTV USB SECAM_L fixed (needed some picture X and Y shiftings)
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It has been confirmed that the FlyDVB IR codes currently in the kernel
work with the LifeView FlyDVB-S LR300. This one line addition adds it
to the list of supported cards.
Signed-off-by: James Le Cuirot <chewi@aura-online.co.uk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before kernel 2.6.14, the driver checked for status before stopping the
thread. So, a compatibility test did exist. After 2.6.14, the
if (state)
were replaced by:
if (1)
However, it makes no sense to keep the if(1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some includes were added after some non-include macros, on old drivers.
Better to keep all includes at the beginning of the files. This change
also helps to make backports to properly work at the development tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in cx88-i2c and cx88-vp3054-i2c.
For one thing, a real template is supposed to be read-only. And in some
cases it's more efficient to initialize the few fields we need
individually.
This clean-up shrinks cx88-i2c.o by 33% and cx88-vp3054-i2c.o by 49%
(x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that it's static, it should no longer be exported to modules...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following doesn't make much sense:
drivers/media/video/Kconfig:
...
config TUNER_TEA5761
tristate "TEA 5761 radio tuner (EXPERIMENTAL)"
...
drivers/media/video/Makefile:
...
ifneq ($(CONFIG_TUNER_TEA5761),)
tuner-objs += tea5761.o
endif
...
With this setup, TUNER_TEA5761=m is equivalent to TUNER_TEA5761=y.
This patch therefore changes TUNER_TEA5761 to a bool.
The missing dependency on EXPERIMENTAL the prompt text indicates also
gets added by this patch.
Additionally, the Makefile entry can now be written in a more compact way.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Virtual Video driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Philips webcam driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
--
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bttv driver has code to detect if a tda9887 is present, that was previous
used to auto-load the tda9887 driver. Now there is no tda9887 driver, so the
code is pointless; it just figures out if it should load the driver and then
does nothing.
For cards that are defined as having no tuner, the init code would still do
i2c probes for various tuner devices and auto-load the tuner module. That can
be skipped for cards that don't need it. The code is made to understand that
in addition to 'UNSET', 'TUNER_ABSENT' also means no tuner.
The tuner into printk()s are also made nicer. Levels are added, INFO or
WARNING, depending on the meaning. For cards with no tuner, or no tuner
defined, a more informative message is printed.
Card has no tuner, before patch:
bttv0: tuner type=-1
or
bttv0: tuner type=4
After patch:
bttv0: tuner absent
Card has a tuner, but the type isn't defined, before patch:
bttv0: tuner type=-1
After patch:
bttv0: tuner type unset [<- also warning now, as the tuner won't work right]
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add analog video support for DViCO FusionHDTV 2
Thanks to Todd Ignasiak for donating the card.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old description was "Philips 1236D ATSC/NTSC dual in", which can be
confused with other Philips tuner models. This patch corrects the name
to "Philips FCV1236D ATSC/NTSC dual in", and updates the range and params
array names to match the description.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove hardcoded fcv1236d tuner programmming from or51211.c
- Alter dvb-bt8xx for the pcHDTV-2000 to use dvb-pll for fcv1236d support.
Thanks to Jarom Hatch <jshatch@gmail.com> for testing this change.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support to the dvb-pll library for the
Philips fcv1236d tuner, based on the FCV1236D datasheet.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb_usb_device* d is not used anymore and can be removed.
Signed-off-by: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add Trust Powerc@m 970Z (0x06d6:0x003b) to the list of supported devices.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Potentially, all board types with I2C and IR support can use an i2c
based IR. Currently, the driver is selected only if bt848 or saa7134
boards are selected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the function, cx88_ir_handle_key:
- convert nested if statement to a switch..case block
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add support for the I2C based IR transceiver of the Hauppauge HVR-1300
- remove bad code from cx88-input.c
Signed-off-by: Jan Frey <jfrey@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We must set i2c_msg.addr in order for the autodetection test to succeed!
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Closes the issue opened on Kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=8383
There's no need to print timeout without debug turned on:
Apr 27 23:02:14 video kernel: cx88[1]/2-mpeg: cx8802_timeout
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
'tuner_pass_ctrl' functionality of the dib3000-mb devices was broken in
the previous changeset:
"dibusb-mb: convert pll handling to properly use dvb-pll"
This patch fixes this problem by assigning this functionality to the
i2c_gate_ctrl callback
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These two functions are no longer being used:
dvb_usb_tuner_init_i2c
dvb_usb_tuner_set_params_i2c
This functionality has been taken over by dvb-pll
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The last user of dvb_pll_configure was the dvb-usb function
dvb_usb_tuner_calc_regs(), which was nothing more than a wrapper around
dvb_pll_configure(). It's just a copy of the functionality provided by
the tuner_ops calc_regs method, and can be deleted.
There were two users of dvb_usb_tuner_calc_regs().
One was dvb_usb_tuner_set_params_i2c(), which is converted to use
fe->ops.tuner_ops.calc_regs().
The other was the digitv driver. This driver can use one of two demods,
mt352 or nxt6000.
For the mt352, the driver would set tuner_ops.calc_regs to
dvb_usb_tuner_calc_regs().
We can just attach dvb_pll and use the tuner_ops.calc_regs() provided by
that module. For the nxt600, the driver would set tuner_ops.set_params
to digitv_nxt6000_tuner_set_params.
That function would in turn use dvb_usb_tuner_calc_regs().
We convert it to use tuner_ops.calc_regs() instead, and use
dvb_pll_attach.
The digitv_tuner_attach() needs to know which frontend was attached by
digitv_frontend_attach(), since the nxt6000 needs tuner_ops.set_params()
to be overridden with digitv_nxt6000_tuner_set_params().
So, to do this a digitv_state that says which frontend was used is added
to the dvb_usb_device private state field.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sound recording doesn't work for this card because ACNI and ACPF
are not set before snd_card_saa7134_capture_prepare(). As a result
timeout occurs. These registers aren't poked because thread
never gets wake up signal. ACNI initialization is done in the
thread.
Sound is muted when capture stops. Shouldn't be because it may
be used during TV playback.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following two pointers in struct cx8802_dev are unused - remove them:
void* fe_handle;
int (*fe_release)(void *handle);
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old service_set_out setting was still tested, even though it no longer
was ever set and was in fact obsolete. This meant that everything that was
written to /dev/vbi16 was ignored. Removed the service_set_out variable
altogether and now it works again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(), close()
and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for pair OV7630+SN9C120
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move tuner callback function pointers out of struct tuner, into
struct tuner_operations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Procfs support on V4L were converted to sysfs support by a pre-2.6 patch:
http://www.ussg.iu.edu/hypermail/linux/kernel/0307.1/2356.html
There's no sense on keeping the dead code inside vicam.c. Also,it won't
work anyway, as part of proc_fs support were previously inside
videodev.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_BIGPHYS_AREA is an out-of-tree kernel patch. It makes no sense to
keep supporting this on mainstream.
The out-of-tree compilation with CONFIG_BIGPHYS_AREA will still be
preserved at the v4l-dvb development tree at:
http://linuxtv.org/hg/v4l-dvb
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The line, "#include <media/tuner.h>" appears twice.
This patch removes the second occurance.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Makefiles in the dvb directory tree used '=' when defining EXTRA_CFLAGS
rather than '+=', which is far more common in the rest of the kernel source.
= 14 times (9 of which this patch removes)
:= 25 times
+= 123 times
This change also has certain advantages for the out of kernel v4l-dvb build
system.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Although it is safe to kfree(NULL), We only need to kfree(priv)
if the release callback is undefined. As it stands now, there
is some redundancy in the operation of releasing the priv data
structures. This patch will call kfree(priv) and set priv to NULL,
if the release callback isnt defined. Otherwise, let the release
callback handle this itself.
Thanks to Mauro Carvalho Chehab for suggesting this.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define tuner release callbacks for mt20xx, tda9887 and tda8290, so that
these drivers can release their own private structures themselves.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Individual tuner drivers are now allocating memory themselves for
their own private data structures. This changeset adds a release
callback to the tuner operations, so that newer drivers that may
require more complex data structures may release this private data
themselves.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a typo the tea5761 tuner support was dead code.
This patch also fixes a bug in the no longer dead code:
A void function can't return anything.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that cx88-blackbird is only accepting the official firmware image,
we no longer have any need to store the size of the firmware inside the
cx88 data structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove temporary support for older 256 kB firmwares.
ivtv, pvrusb2 and blackbird can now all handle the newer larger firmwares,
so support for the older (buggier) firmware can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For backwards compatibility firmware files of 256 Kb were allowed: all
drivers have now been updated to support the newer larger firmwares so
remove this compatibility code and only support the newer firmware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi scatter method were used as a proof of concept. It can be
safelly removed from mainstream, since the current method is
faster and better than the previous solution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create private data struct for device specific private data.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the long-dead references to the obsolete MODULE_PARM macro.
Given that the first one of those is actually misspelled as
"MODULE_PARAM", it's clear that they can't have been doing any good.
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor at mail.ru>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make sure devices manufactured by Dposh are not affected by previous hw
pid filtering changes
Doing so might crash it.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several return value related problems in zr364xx.
- return -ENOMEM instead of -ENODEV on out of memory
- zr364xx checks video_register_device() error only when
its return value is -1. But video_register_device() doesn't
always return -1 on error.
- If usb_register() returns error, module_init() wrongly returns 1:
retval = usb_register(&zr364xx_driver) < 0;
...
return retval;
And it allows the module to be loaded. Because sys_init_module() doesn't
see positive return value as error.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that dvb-pll is being used properly in all cx88-dvb instances,
the cx88 driver no longer needs to store pll_desc nor pll_addr.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.
The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point. This the recommended value for
DVB-T operation.
The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).
The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.
CX88_BOARD_HAUPPAUGE_HVR1100 Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000 Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300 Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod
This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence. The non-dvb-pll code for this
user is removed.
X88_BOARD_DNTV_LIVE_DVB_T_PRO digitalnow DNTV Live! DVB-T Pro
In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:
SAA7134_BOARD_MD7134 Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID Asus Europa2 OEM
The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.
This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.
For the cxusb driver, only one board is effected:
USB_PID_MEDION_MD95700 Medion MD95700
This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively. These functions are effectively the same
as the dvb-pll versions. They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does). This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for A-LINK DTU(m) is not included in this patch.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
convert calls to dib3000mb_attach to use dvb_attach
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
moved tda665x pll_init into dvb_pll_desc dvb_pll_tda665x.initdata
convert handling of tda665x and tua6010xs to properly use dvb-pll
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These sources do not need to #include "dvb-pll.h"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using Encore's key codes, we needn't add any additional key table.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the 10moons TM300 TV card (so called TV Master 3), which is a
10moons saa7130 based board. Here not include features for the
IR-remote.
It has been tested using TVTIME. The card was auto-detected and all the
input sources worked correct with sound.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ioctl entry point, a big switch/case, is splitted in little
functions.
These functions are set as callbacks for the video_ioctl2 video4linux
facility.
This improves the driver memory consumption and enables the v4l1
compatibility as a side effect.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Radio and video ioctls are the same,
delete the usbvision_do_radio_ioctl function
add the special cases for radio in usbvision_v4l2_do_ioctl
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
usbvision_set_video_format: add comment that VO_MODE is also being set.
Signed-off-by: David Warman <dwarman@davidwarman.net>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.
The functionality is added to dvb-pll, where all the other code that
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link. Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.
It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).
It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted and tested by Thomas Sattler <tsattler@gmx.de>.
cinergyT2.c does cancel_delayed_work() + flush_scheduled_work() while
holding cinergyt2->sem. This leads to deadlock because work->func()
needs the same mutex to complete. Another bug is that this code in fact
can't reliably stop the re-arming delayed_work.
Convert this code to use cancel_rearming_delayed_work() and move it
out of ->sem. Another mutex, ->wq_sem, was added to protect against the
concurrent open/resume.
This patch is a horrible hack to fix the lockup which happens in practice.
As Dmitry Torokhov pointed out this driver has other problems and needs
further changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l-info and other programs would loop indefinitely while querying the
tuners for cx88-blackbird cards.
The cause was that vidioc_g_tuner didn't return an error value for
qctrl->id != 0, making the application think there is a never ending
list of tuners...
This patch adds the same index check as done in vidioc_g_tuner() in
cx88-video.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one uses a V4L *one* application, such as vlc or mplayer's v4l driver, as
the first user after the driver is loaded, the driver wedges itself and will
never capture properly. Even if one uses a V4L2 application later, it still
won't work.
If one uses a V4L *two* application first, such as tvtime or mplayer's v4l2
driver, then the driver will be ok. One can then run a V4L1 application, and
it will work.
It turns out the problem is with norm changing and the crop support that was
added in 2.6.21. The driver defaults to PAL, and keeps the last norm it was
set too across opens. If one changes the norm via V4L1, the cropping
parameters are not reset like they should be, and they'll remain broken across
device opens.
This patch removes the direct setting of btv->tvnorm in the V4L1 ioctl
VIDIOCSCHAN handler. The norm is set via the existing call to set_input(),
which calls set_tvnorm(), which will reset the cropping values now that it is
able to detect the norm change.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the test for the thread pid from >= 0 to > 0.
When the saa8134 driver initialization fails after a certain point, it goes
through the complete shutdown process for the driver. Part of shutting it
down includes tearing down the thread for tv audio.
The test for tearing down the thread tests for >= 0. Since the dev
structure is kzalloc'd, the test will always be true if we haven't tried to
start the thread yet. We end up waiting on pid 0 to complete, which will
never happen, so we lock up.
This bug was observed in Novell Bugzilla 284718, when request_irq() failed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one has a dependency chain (tristate)FOO depends on (bool)BAR depends on
(tristate)BAZ, build problems will result. If BAZ=m, then BAR can be set
y, which allows FOO=y. It's possible to have FOO=y && BAZ=m, which
wouldn't be allowed if FOO depended directly on BAZ. In effect, the bool
promotes the tristate from m to y.
This ends up causing a problem with several menuconfigs that look like:
menuconfig BAR
bool
depends on BAZ [tristate]
if BAR
config FOO
tristate
endif
The solution used here is to add the dependencies of BAR to the if
statement, so that items in the if block will gain a direct
non-bool-promoted dependency on BAZ. This is how it would work if a menu
was used instead of an if block.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves flexcop-dma (currently used only by flexcop-pci) to
b2c2-flexcop-pci module, that is dependent on CONFIG_PCI, fixing the bug
as reported by Geert Uytterhoeven <geert@linux-m68k.org>:
drivers/media/dvb/b2c2/flexcop-dma.c uses the PCI DMA API, but
DVB_B2C2_FLEXCOP doesn't depend on PCI, causing the following problem on
PCI-less systems:
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
Apparently this is the flexcop DMA core, which is used by both
DVB_B2C2_FLEXCOP_PCI and DVB_B2C2_FLEXCOP_USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VIDIOC_CROPCAP ioctl was missing in ivtv.
The handling of output video cropping was wrong. This has now been fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CAP_VIDEO_OUTPUT_POS was initially introduced for 2.6.22 but never
actually used: remove it before the final 2.6.22 is made.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed the urb allocation part that was not taking into account the current alternate setting
this fixes usb_submit_urb returning -90 errno in isocIrq.
- fixed usb_submit_urb returning -1 errno in isocIrq (need to ignore usb urb with status==-ENOENT)
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several people reported unreliable reception with the current driver.
Furthermore, STR and SNR values seem to be inverted.
This fix is based on a patch posted by Hartmut Hackman.
Thanks to Helmut Auer for testing and helping to optimize the patch.
tda826x:
- set baseband cut-off to 19 MHz
tda10086:
- change the parameters of the carrier recovery loop
- toggle register 0x02 between 0x35 (tuning) and 0x00 (locked)
- invert STR and SNR values
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sliced VBI transfers use PIO instead of DMA. This was done inside the
interrupt handler, but since PIO accesses are very slow this meant that
a lot of time was spent inside the interrupt handler. All PIO copies are
now moved to a workqueue. This should fix various issues with missing time
ticks and remote key hits.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If this mutex_lock_interruptible() does fail due to signal_pending() then the
state of the driver will get trashed in interesting ways, because userspace
cannot and will not retry the close().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the SAA7111 device is powered down, and requires re-initialisation when
the V4L device is opened (as on the NetWinder), the SAA7111 driver gets
completely confused about the current settings.
The problem is centred around the way the driver keeps _two_ cached copies
of the current settings - one of the struct video_picture settings, and one
of the registers.
When the decoder is re-initailised, the cached register settings are
overwritten, as are the values in the hardware registers. However, the
cached video_picture settings are not.
Resolve this by removing the useless and buggy second level of caching for
video_picture. Instead, provide a function which updates register values
if and only if the value we are going to write to the register has changed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The recent changes on Kconfig broke compilation when VIDEO_DEV is compiled
as module. On some cases, drivers like VIDEO_BUF are compiled with 'y' option
instead of 'm':
...
Thanks to: Toralf Forster <toralf.foerster@gmx.de> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A bug in the ov7670 sensor causes it to introduce noise unless the CLKRC
register is rewritten *after* setting the image mode. Naturally,
resetting CLKRC in this way will cause other modes to fail. So
carefully poke the register only when indicated.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The proper method for powering down the sensor on OLPC systems has
changed somewhat; in particular, the sensor must be powered down
completely (rather than simply told to power down) or the associated
"camera active" LED will stay on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow to use SECAM-BG with the FI1216MF tuner.
The selection is done with the secam=B module argument.
The default behaviour should be the same as before.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb-core is not started early enough when device drivers that use dvb are
compiled in so dvb_register_device fails (silently) since dvb_class is
NULL, this runs dvb_init using subsys_initcall instead of module_init.
dvb_register_device will now check the return value of class_device_create.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reverted the change to struct v4l2_pix_format. I completely missed that
this struct was used by existing ioctls so that changing it broke the ABI.
I will have to think of another way of setting the top/left coordinates
but for now this change is reverted to preserve compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (44 commits)
V4L/DVB (5571): V4l1-compat: Make VIDIOCSPICT return errors in a useful way
V4L/DVB (5624): Radio-maestro.c cleanup
V4L/DVB (5623): Dsbr100.c Replace usb_dsbr100_do_ioctl to use video_ioctl2
V4L/DVB (5622): Radio-zoltrix.c cleanup
V4L/DVB (5621): Radio-cadet.c Replace cadet_do_ioctl to use video_ioctl2
V4L/DVB (5619): Dvb-usb: fix typo
V4L/DVB (5618): Cx88: Drop the generic i2c client from cx88-vp3054-i2c
V4L/DVB (5617): V4L2: videodev, allow debugging
V4L/DVB (5614): M920x: Disable second adapter on LifeView TV Walker Twin
V4L/DVB (5613): M920x: loosen up 80-col limit
V4L/DVB (5612): M920x: rename function prefixes from m9206_foo to m920x_foo
V4L/DVB (5611): M920x: replace deb_rc with deb
V4L/DVB (5610): M920x: remove duplicated code
V4L/DVB (5609): M920x: group like functions together
V4L/DVB (5608): M920x: various whitespace cleanups
V4L/DVB (5607): M920x: Initial support for devices likely manufactured by Dposh
V4L/DVB (5606): M920x: add "c-basic-offset: 8" to help emacs to enforce tabbing
V4L/DVB (5605): M920x: Add support for LifeView TV Walker Twin
V4L/DVB (5603): V4L: Prevent queueing queued buffers.
V4L/DVB (5602): Enable DiSEqC in Starbox II (vp7021a)
...
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Among other things, VIDIOCSPICT sets the pixel format. Some drivers
don't support all formats, e.g. cx88 doesn't support the planar formats.
The compat code that translates VIDIOCSPICT into V4L2 ioctls doesn't pass
on any errors, so a userspace program doesn't know if it has selected an
unsupported pixel format.
VIDIOCSPICT sets both the memory capture and overlay formats, and it's
possible that one will be set while the other will fail, e.g. cx88
doesn't even support overlay. Also, trying to set the overlay format
will fail for non-root users.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert dsbr100 to use video_ioctl2
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert radio-cadet to use video_ioctl2
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the generic client declared in cx88-vp3054-i2c: it's not used
anywhere. This shrinks cx88-vp3054-i2c.o by 29% on x86_64. Unless it
was there for later use?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Disable second adapter on LifeView TV Walker Twin while it doesn't work
properly.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do not follow 80-col limit where it would cause inconsistency.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
deb_rc is used by the dvb-usb core framework. This patch replaces all
occurances of deb_rc with deb, in m920x.c, so that its clear that we're
not using dvb-usb's deb_rc.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some of the devices supported by the m920x driver have identical functions used
for tuner_attach and frontend_attach. This patch consolidates the functions in
question, and updates the debug code to be generic for each. This patch
decreases the size of the kernel.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Group the tuner configurations together.
- Group the demod configurations together.
- Group the device-specific initialization functions together.
- Group demod_attach functions together.
- Group tuner_attach functions together.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These devices are sold by various companies and chains not involved in
hardware manufacturing business. This particular device owned by
winisch (from irc) had a sticker with text "TCM 234292" on it. This device
was never opened so it is possible that Dposh did not manufacture this
stick. However, the bundled software and their product line points into
that direction. Also thanks to Michael Krufky for spotting this hw
filtering problem and thus avoiding hair loss.
Hardware pid filters and the bundled remote controller are not currently
supported on this device.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for "LifeView TV Walker Twin" (USB IDs 10fd:0513, 10fd:0514)
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf_qbuf queues buffers to q->stream but does not properly check
the state of the buffer before queueing. It was possible to queue
buffers that already were in the queue.
Only buffers that are in states STATE_NEEDS_INIT and STATE_IDLE can be
queued.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uncomments code in vp702x-fe.c to enable DiSEqC in vp7021a
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Pat Erley <pat@erley.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Also remove one indirection (CONFIG_DVB) that does not seem to
be really used inside the kernel.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Revert changeset
http://linuxtv.org/hg/v4l-dvb?cmd=changeset;node=e7c424bbf9aa;style=gitweb
Petri Helin found that this changeset broke tuning:
'Well, after going through the changes that might have had effect on
tuning, I found out the one which had caused this problem. I do not know
the actual reason behind the change, but the changelog says that it
was meant to "Fix TD1316 tuner for DVBC". But at least in my case it
seams to have broken the tuner instead.'
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Thanks-to: Petri Helin <phelin@googlemail.com>
Acked-by: e9hack <e9hack@googlemail.com>
Acked-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
