This finally adds the PPC_PRPMC2800 Kconfig option, the board setup
code (the setup and reset functions) and the defconfig, to support the
Motorola PrPMC2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_cache_coherency() verifies that the cache coherency setting of
the kernel (CONFIG_NOT_COHERENT_CACHE) matches that left by the firmware,
as indicated by coherency-off device tree property.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD). The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.
Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).
So, the missing configuration needs to be done in either the bootwrapper
or in the kernel. To keep the kernel as clean as possible, it is done
in the bootwrapper. Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).
Table of routines and the windows they configure:
mv64x60_config_ctlr_windows() ENET->System Memory
MPSC->System Memory
IDMA->System Memory
mv64x60_config_pci_windows() PCI MEM->System Memory
PCI I/O->Bridge's Registers
mv64x60_config_cpu2pci_window() CPU->PCI MEM
CPU->PCI I/O
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.
Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time. This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees. By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.
The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address. This
fixes it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An mdio bus scan was added with ucc_geth phylib
migration patches, now machines complain on boot, saying:
prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@00
prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@01
since size-cells can indeed be 0, this patch fixes the check.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Greatly simplify the function smp_space_timers.
The stolen time calculation (per comment within the code) doesn't need the
half-jiffy stagger any more. There isn't an issue with bouncing off global
locks, so we really shouldn't need any sort of staggering at all.
However, the last_jiffy value still needs to be set. This removes the
extra stagger logic, and just sets the values.
This change should benefit applications that rely on barrier
synchronization, and will help cut down OS jitter.
Boot tested across the board (G5,power3,power4,power5,970mp blade).
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes warnings:
arch/powerpc/platforms/ps3/system-bus.c: In function 'ps3_map_sg':
arch/powerpc/platforms/ps3/system-bus.c:278: warning: unused variable 'i'
arch/powerpc/platforms/ps3/system-bus.c:277: warning: unused variable 'dev'
arch/powerpc/platforms/ps3/setup.c:103: warning: 'prealloc' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fixes:
arch/powerpc/platforms/pasemi/idle.c: In function 'pasemi_system_reset_exception':
arch/powerpc/platforms/pasemi/idle.c:55: warning: implicit declaration of function 'do_IRQ'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This case will never be hit, but it should be corrected anyway.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Board support and default configuration file for the Micrel/Kendin
KS8695 Development board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add core support for the Kendin/Micrel KS8695 processor family.
It is an ARM922-T based SoC with integrated USART, 4-port Ethernet
Switch, WAN Ethernet port, and optional PCI Host bridge, etc.
http://www.micrel.com/page.do?page=product-info/sys_on_chip.jsp
This patch is based on earlier patches from Lennert Buytenhek, Ben
Dooks and Greg Ungerer posted to the arm-linux-kernel mailing list in
March 2006; and Micrel's 2.6.9 port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9RL-EK development board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.
(Dependent on ARM patch #4370/2)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Quicklist support for IA64
[IA64] fix Kprobes reentrancy
[IA64] SN: validate smp_affinity mask on intr redirect
[IA64] drivers/char/snsc_event.c:206: warning: unused variable `p'
[IA64] mca.c:121: warning: 'cpe_poll_timer' defined but not used
[IA64] Fix - Section mismatch: reference to .init.data:mvec_name
[IA64] more warning cleanups
[IA64] Wire up epoll_pwait and utimensat
[IA64] Fix warnings resulting from type-checking in dev_dbg()
[IA64] typo s/kenrel/kernel/
The code was ok, but triggered warnings for calling __init from
__cpuinit. Instead call it from check_bugs instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G. Linux complains:
"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."
I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:
AK: use correct types for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've got the following linking error when building 2.6.21-mm2 on ARM:
ERROR: "csum_partial_copy_from_user" [net/rxrpc/af-rxrpc.ko] undefined!
Linking fails because "csum_partial_copy_from_user" is not exported to
modules. This patch adds it to the list of exported symbols.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
[MIPS] Rework cobalt_board_id
[MIPS] Use RTC_CMOS for Cobalt
[MIPS] Use platform_device for Cobalt UART
[MIPS] Separate Alchemy processor based boards config
[MIPS] Fix build error in atomic64_cmpxchg
[MIPS] Run checksyscalls for N32 and O32 ABI
[MIPS] tlbex: use __maybe_unused
[MIPS] excite: use __maybe_unused
[MIPS] Add extern cobalt_board_id
[MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
[MIPS] Rename tb0229_defconfig to tb0219_defconfig
[MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
[MIPS] Add minimum defconfig for RBHMA4200
[MIPS] SB1: Build fix.
[MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
[MIPS] clocksource: use CLOCKSOURCE_MASK() macro
[MIPS] Remove LIMITED_DMA support
[MIPS] Remove Momenco Jaguar ATX support
[MIPS] Remove Momenco Ocelot G support
[MIPS] FPU hazard handling
...
* 'audit.b38' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Abnormal End of Processes
[PATCH] match audit name data
[PATCH] complete message queue auditing
[PATCH] audit inode for all xattr syscalls
[PATCH] initialize name osid
[PATCH] audit signal recipients
[PATCH] add SIGNAL syscall class (v3)
[PATCH] auditing ptrace
Enable devices to signal interrupts via PCI memory cycles.
rev6:
* fix enable/disable typo, Michael Ellerman
rev5:
* fix up ack, enable, and disable for iop13xx_msi_chip
rev4:
* move smp compile fix to separate patch
* use dynamic_irq_init in create_irq()
* hookup mask/unmask routines in iop13xx_msi_chip
rev3:
* change msi.c to use linux/smp.h instead of asm/smp.h
* call dynamic_irq_cleanup at destroy_irq time
rev2:
* destroy_irq did not take the full 128 bits of msi_irq_in_use into account
* added missing '&' for calls to test_and_set_bit and clear_bit
[ebiederm@xmission.com: review comments/suggestions]
[dan.j.williams@intel.com: cleanups/forward port to 2.6-git]
Signed-off-by: Daniel Wolstenholme <daniel.e.wolstenholme@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IA64 is the origin of the quicklist implementation. So cut out the pieces
that are now in core code and modify the functions called.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ab1b6f03a1 said
- remove the unused task argument to save_stack_trace, it's always current
then broke arm:
arch/arm/kernel/stacktrace.c:56: error: conflicting types for 'save_stack_trace'
include/linux/stacktrace.h:11: error: previous declaration of 'save_stack_trace' was here
arch/arm/kernel/stacktrace.c:56: error: conflicting types for 'save_stack_trace'
include/linux/stacktrace.h:11: error: previous declaration of 'save_stack_trace' was here
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case of reentrance i.e when a probe handler calls a functions which
inturn has a probe, we save a previous kprobe information and just single
step the reentrant probe without calling the actual probe handler. During
this reentracy period, if an interrupt occurs and if probe happens to
trigger in the inturrupt path, then we were corrupting the previous kprobe(
as we were overriding the previous kprobe info) info their by crashing the
system. This patch fixes this issues by having a an array of previous
kprobe info struct(with the array size of 2).
This similar technique is not needed on i386 and x86_64 because by default
interrupts are turn off in the break/int3 exception handler.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the apparently useless config option GENERIC_BUST_SPINLOCK,
since nothing in the source tree refers to it.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On SN, only allow one bit to be set in the smp_affinty mask when
redirecting an interrupt. Currently setting multiple bits is allowed, but
only the first bit is used in determining the CPU to redirect to. This has
caused confusion among some customers.
[akpm@linux-foundation.org: fixes]
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add base kernel support for the TI DaVinci platform.
This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init. More
drivers to come.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Trying to build current git tree fails. The failure is due to commit
25ff0a6530. The patch title say it's for
OMAP board while it's applied on S3C2410 Kconfig entry. Moreover, the
OMAP entry is already selecting GENERIC_TIME.
This patch reverts the offending commit.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached you can find a patch needed to make the LEDS for 'CPU-Idle'
and 'Timer' work on the AT91SAM9261-EK board. The kernel configuration
options are already there, but the implementation is not available.
Signed-off-by: Remy Bohmer <l.pinguin@gmail.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-ebsa110/io.c:106: error: conflicting types for 'readsw'
arch/arm/mach-ebsa110/io.c:116: error: conflicting types for 'readsl'
arch/arm/mach-ebsa110/io.c:161: error: conflicting types for 'writesw'
arch/arm/mach-ebsa110/io.c:171: error: conflicting types for 'writesl'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a small driver responsible for configuring the UART used
for the bluetooth chip and for enabling the bluetooth chipset.
Additionnaly, can trigger a led if the H1940 led driver is enabled.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the ac97 clock to the s3c2443 machine files. It seems to
have been simply missed out previously.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This update for trizeps4 SoM contains:
- support for new TFT on more recent ConXS evalboard
- correct partition of flash device
- update of "trizeps4_defconfig"
Signed-off-by: Jrgen Schindele (linux@schindele.name)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards. Convert all expansion card drivers to use them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.
Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.
This fixes potential problems caused by drivers forgetting to
remove these hooks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch wires the eventfd system call to the x86 architectures.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch wires the timerfd system call to the x86 architectures.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch wires the signalfd system call to the x86 architectures.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch renames the raw hard_irq_{enable,disable} into
__hard_irq_{enable,disable} and introduces a higher level hard_irq_disable()
function that can be used by any code to enforce that IRQs are fully disabled,
not only lazy disabled.
The difference with the __ versions is that it will update some per-processor
fields so that the kernel keeps track and properly re-enables them in the next
local_irq_disable();
This prepares powerpc for my next patch that introduces hard_irq_disable()
generically.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make kernel stacks be 1 page on i386 and 2 pages on x86_64. These match the
host values.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a separate IRQ stack. This differs from i386 in having the entire
interrupt run on a separate stack rather than starting on the normal kernel
stack and switching over once some preparation has been done. The underlying
mechanism, is of course, sigaltstack.
Another difference is that interrupts that happen in userspace are handled on
the normal kernel stack. These cause a wait wakeup instead of a signal
delivery so there is no point in trying to switch stacks for these. There's
no other stuff on the stack, so there is no extra stack consumption.
This quirk makes it possible to have the entire interrupt run on a separate
stack - process preemption (and calls to schedule()) happens on a normal
kernel stack. If we enable CONFIG_PREEMPT, this will need to be rethought.
The IRQ stack for CPU 0 is declared in the same way as the initial kernel
stack. IRQ stacks for other CPUs will be allocated dynamically.
An extra field was added to the thread_info structure. When the active
thread_info is copied to the IRQ stack, the real_thread field points back to
the original stack. This makes it easy to tell where to copy the thread_info
struct back to when the interrupt is finished. It also serves as a marker of
a nested interrupt. It is NULL for the first interrupt on the stack, and
non-NULL for any nested interrupts.
Care is taken to behave correctly if a second interrupt comes in when the
thread_info structure is being set up or taken down. I could just disable
interrupts here, but I don't feel like giving up any of the performance gained
by not flipping signals on and off.
If an interrupt comes in during these critical periods, the handler can't run
because it has no idea what shape the stack is in. So, it sets a bit for its
signal in a global mask and returns. The outer handler will deal with this
signal itself.
Atomicity is had with xchg. A nested interrupt that needs to bail out will
xchg its signal mask into pending_mask and repeat in case yet another
interrupt hit at the same time, until the mask stabilizes.
The outermost interrupt will set up the thread_info and xchg a zero into
pending_mask when it is done. At this point, nested interrupts will look at
->real_thread and see that no setup needs to be done. They can just continue
normally.
Similar care needs to be taken when exiting the outer handler. If another
interrupt comes in while it is copying the thread_info, it will drop a bit
into pending_mask. The outer handler will check this and if it is non-zero,
will loop, set up the stack again, and handle the interrupt.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some tidying of the irq code before introducing irq stacks. Mostly
style fixes, but the timer handler calls the timer code directly
rather than going through the generic sig_handler_common_skas.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have UM_THREAD_SIZE, we can replace the calculations in
user-space code (an earlier patch took care of the kernel side of the
house).
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replaced task_protections with stack_protections since they do the same
thing, and task_protections was misnamed anyway.
This needs THREAD_SIZE, so that's imported via common-offsets.h
Also tidied up the code in the vicinity.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the tlb-miss handler (tme_handler) to check _PAGE_PRESENT bit
in order to handle file-mapped or swapped-out pages correctly.
This patch is required to fix unexpected page errors for m32r.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a rarely-happened but severe scheduling problem of
the recent m32r kernel of 2.6.17-rc3 or later.
In the following previous m32r patch, the switch_to macro was
modified not to do unnecessary push/pop operations for tuning.
> [PATCH] m32r: update switch_to macro for tuning
> 4127272c38
In this modification, only 'lr' and 'sp' registers are push/pop'ed,
assuming that the m32r kernel is always compiled with
-fomit-frame-pointer option.
However, in 2.6 kernel, kernel/sched.c is irregularly compiled
with -fno-omit-frame-pointer if CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER
is not defined.
-- kernel/Makefile --
:
ifneq ($(CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER),y)
# According to Alan Modra <alan@linuxcare.com.au>, the -fno-omit-frame-pointer is
# needed for x86 only. Why this used to be enabled for all architectures is beyond
# me. I suspect most platforms don't need this, but until we know that for sure
# I turn this off for IA-64 only. Andreas Schwab says it's also needed on m68k
# to get a correct value for the wait-channel (WCHAN in ps). --davidm
CFLAGS_sched.o := $(PROFILING) -fno-omit-frame-pointer
endif
:
---
Therefore, for the recent m32r kernel, we have to push/pop 'fp'
(frame pointer) if CONFIG_FRAME_POINTER is defined or
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER is not defined.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace function instances of __attribute__((unused)) with
__maybe_unused to suppress warnings.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o x86_64 kernel needs to be compiled for 2MB aligned addresses. Currently
we are using BUILD_BUG_ON() to warn the user if he has not done so. But
looks like folks are not finding message very intutive and don't open
the respective c file to find problem source. (Bug 8439)
arch/x86_64/kernel/head64.c: In function 'x86_64_start_kernel':
arch/x86_64/kernel/head64.c:70: error: size of array 'type name' is negative
o Using preprocessor directive #error to print a better message if
CONFIG_PHYSICAL_START is not aligned to 2MB boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch has reworked cobalt_board_id.
The cobalt_board_id is read from PCI config register.
It should be in PCI routine.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace function instances of __attribute__((unused)) with
__maybe_unused.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fix these warnings:
WARNING: arch/mips/kernel/built-in.o - Section mismatch: reference to .init.text:free_irqno from __ksymtab_gpl between '__ksymtab_free_irqno' (at offset 0x0) and '__ksymtab_allocate_irqno'
WARNING: arch/mips/kernel/built-in.o - Section mismatch: reference to .init.text:allocate_irqno from __ksymtab_gpl after '__ksymtab_allocate_irqno' (at offset 0x8)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has some hackish code and it odd DMA results in the need to support
old features in kernel code.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Harmless bug because this function is only called in case of another
kernel bug anyway which is also why this was missed for so long.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When auditing syscalls that send signals, log the pid and security
context for each target process. Optimize the data collection by
adding a counter for signal-related rules, and avoiding allocating an
aux struct unless we have more than one target process. For process
groups, collect pid/context data in blocks of 16. Move the
audit_signal_info() hook up in check_kill_permission() so we audit
attempts where permission is denied.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
