Promiscous mode is only for MACs.
Should not disable/enable VLAN filter when entering/leaving promisuous mode.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify port number to avoid crashes if port number is outside the range.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback can't work when port is down.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing says:
====================
bridge: multicast snooping exports #2
Some people pointed out to me that it might be helpful to add stubs for
the newly added multicast exports. That way e.g. batman-adv should continue
to be compile and useable without having to have a kernel compiled
with bridge code in the future. This is what the first patch is supposed
to do.
The second patch adds a third multicast export for the bridge which
e.g. batman-adv is supposed to use, too, soon: Just like the bridge
disables its multicast snooping activities if no querier is present,
batman-adv needs to do the same if bridges are involved.
These three exports should be the final ones needed to marry the bridge
multicast snooping with the batman-adv multicast optimizations recently
added for the 3.15 kernel, allowing to use these optimzations in common
setups having a bridge on top of e.g. bat0, too. So far these bridged
setups would fall back to simple flooding through the batman-adv mesh
network for any multicast packet entering bat0.
More information about the batman-adv multicast optimizations currently
implemented can be found here:
http://www.open-mesh.org/projects/batman-adv/wiki/Basic-multicast-optimizations
The integration on the batman-adv side could afterwards look like this,
for instance (now including the third export):
http://git.open-mesh.org/batman-adv.git/commitdiff/61e4f6af4b7a21ed4040f2e711d50c778e5b6d93?hp=6ae4281474675fbca5bedcf768972a32db586eb6
====================
With this patch other modules are able to ask the bridge whether an
IGMP or MLD querier exists on the according, bridged link layer.
Multicast snooping can only be performed if a valid, selected querier
exists on a link.
Just like the bridge only enables its multicast snooping if a querier
exists, e.g. batman-adv too can only activate its multicast
snooping in bridged scenarios if a querier is present.
For instance this export avoids having to reimplement IGMP/MLD
querier message snooping and parsing in e.g. batman-adv, when
multicast optimizations for bridged scenarios are added in the
future.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make users (e.g. batman-adv soon) load- and runnable even if the
bridge was compiled without snooping capabilities - or even if the
kernel was compiled without any bridge code at all.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression bug caused by:
067608e9d0 ("tipc: introduce direct
iovec to buffer chain fragmentation function")
If data is sent on a nonblocking socket and the destination link
is congested, the buffer chain is leaked. We fix this by freeing
the chain in this case.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues with debug printk calls across the driver, normally
disabled; first compilation errors:
drivers/net/fddi/defxx.c:676:1: error: pasting "(" and ""In dfx_bus_init...\n"" does not give a valid preprocessing token
drivers/net/fddi/defxx.c:820:1: error: pasting "(" and ""In dfx_bus_uninit...\n"" does not give a valid preprocessing token
and so on, and then warnings:
drivers/net/fddi/defxx.c: In function 'dfx_driver_init':
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
etc. Additionally casts are removed from virtual addresses and %p used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej W. Rozycki says:
====================
defxx: Fixes for 64-bit host support
This mini patch series addresses issues with 64-bit host support for FDDI
interface boards supported by the defxx driver where DMA mapping
synchronisation is required on swiotlb systems. While PDQ, the DMA engine
chip used with these boards, supports 48-bit addressing that would
normally suffice for typical 64-bit systems in existence, the host bus
interface chips used by individual implementations have their limitations
as follows:
* DEFTA or DEC FDDIcontroller/TURBOchannel -- there's no host bus
interface chip, the PDQ connects to TURBOchannel directly; TURBOchannel
supports DMA addressing of up to 16GB (34-bit addressing), however no
TURBOchannel system has ever been made that supports more than 1GB of
RAM, so in reality no remapping is ever required,
* DEFEA or DEC FDDIcontroller/EISA -- the ESIC EISA interface chip only
supports 32-bit addressing, all accesses beyond 4GB have to be remapped,
* DEFPA or DEC FDDIcontroller/PCI -- the PFI PCI interface chip rev. 1 & 2
only support 32-bit addressing, they have 32 AD lines only both on the
PDQ and the PCI side, and consequently no Dual Address Cycle support, so
all accesses beyond 4GB have to be remapped; the range of addressing
supported by PFI rev. 3 is currently not certain, however the chip is
backwards compatible with earlier revisions and will work with code that
supports them.
Some other issues discovered in the course of correcting 64-bit support
have been fixed as well. Each of the patches is functionally
self-contained and can be applied independentely, although there may be
mechanical dependencies making it necessary to apply patches in order.
The driver suffers from non-standard formatting and while I did my best
with these bug fixes to follow our coding style, I found some pieces
hopeless, checkpatch.pl will complain. I plan to reformat the whole
driver, that will inevitably require factoring out some pieces into
separate functions, but that's going to be a major effort and therefore I
want to do this separately, with no functional changes made at the same
time. If anyone has specific suggestions as to how to reformat any of the
pieces submitted here for a better layout, then I'll be happy to take them
into account.
And last but not least many thanks to Robert Coerver, who was the most
recent person to report this problem with the driver and was kind enough
to patiently try a few revisions of the driver update on his system as I
was finding and addressing issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DMA synchronisation calls needed in the receive path:
1. To retrieve the Receive Status word that is prepended by the PDQ DMA
engine in the receive buffer, and provides information about the
frame received, including its size and any errors.
2. To make data received available for copying in the small-frame case
(size <= SKBUFF_RX_COPYBREAK) where the original DMA buffer will be
returned to the receive descriptor ring and therefore its mapping
retained.
With DMA mapping error handling in place, added by the other patch,
this may now also trigger where an attempt to map a newly allocated
buffer for DMA has failed. In that case data from the original buffer
will be copied out and the buffer returned to the DMA descriptor ring.
These calls may do nothing when data is in the host DMA addressing range
of the FDDI interface, such as always on 32-bit systems, however their
absence makes frame reception stop functioning reliably on systems that
have memory beyond the low 4GB of the address space.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds error handling for DMA mapping requests; I think there isn't
much else to say about it.
A good side-effect is the mapping in the transmit path is now made with
the board lock released. Also if DMA mapping fails for a newly
allocated receive buffer, then data from the old buffer will be copied
out (as is presently done for small frames only whose size does not
exceed SKBUFF_RX_COPYBREAK) and the original buffer returned, with its
mapping unchanged, to the DMA descriptor ring.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the two remaining places across the driver that use dev_alloc_skb
to netdev_alloc_skb. Another place has already been converted to use
__netdev_alloc_skb, no idea why these two have been left behind.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prearranged receive DMA bounce buffer mappings are not released in the
card reboot/shutdown path. That does not affect frame reception, but
probably explains the random segmentation fault I observed the other day
on interface shutdown. Card is rebooted as required by the spec in the
process of ring fault recovery when a PC Trace signal has been received.
This change fixes the problem in an obvious manner.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive DMA maps are oversized, they include EISA legacy 128-byte
alignment padding in size calculation whereas this padding is never used
for data. Worse yet, if the skb's data area has been realigned indeed,
then data beyond the end of the buffer will be synchronised from the
receive DMA bounce buffer, possibly corrupting data structures residing
in memory beyond the actual end of this data buffer.
Therefore switch to using PI_RCV_DATA_K_SIZE_MAX rather than NEW_SKB_SIZE
in DMA mapping, the value the former macro expands to is written to the
receive ring DMA descriptor of the PDQ DMA chip and determines the
maximum amount of data PDQ will ever transfer to the corresponding data
buffer, including all headers and padding.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight says:
====================
net: sctp: Optimisations to sctp command queue code
These 3 patches optimise the code that processes sctp's command queue.
(A list of 'tasks' to be performed after the rest of the chunk processing.)
1) Inline all the functions from command.c
2) Remove the memset() calls used to zero a word-sized union.
3) Use pointers instead of array indexes.
The combined changes reduce the code size (amd64) by a few kb.
I'm not 100% convinced that the zeroing done in patch 2 is needed at all.
On BE systems it is likely to generate more code than on LE ones.
In fact it might be best to change the union to only contain 'long' sized
items.
Changes for v2:
- Add some missing initialisers in patch 2/3 and delete them in 3/3.
- Modify the commit message for 2/3 to point out that the union
shouldn't need to be zeroed, but the patches aren't intended to
change the behaviour even if the code is buggy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using pointers into sctp_cmd_seq_t.cmds[] lets the compiler generate much
better code.
Use the last entry first to optimise the overflow check.
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if memset() is inlined (as on x86) using it to zero the union
generates a memory word write of zero, followed by a write of the
smaller field, and then a read of the word.
As well as being a lot of instructions the sequence is unlikely to
be optimised by the store-load forward hardware so will be slow.
Instead allocate a field of the union that is the same size as the
entire union and write a zero value to it. The compiler will then
generate the required value in a register.
Zeroing the union shouldn't be necessary, but this patch series isn't
intended to have a behavioural change.
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_init_cmd_seq() and sctp_next_cmd() are only called from one place.
The call sequence for sctp_add_cmd_sf() is likely to be longer than
the inlined code.
With sctp_add_cmd_sf() inlined the compiler can optimise repeated calls.
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This warning is introduced by commit 7b30600cc6 ("appletalk:
fix checkpatch error with indent"), So fix it.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-07-03
Please pull this first batch of wireless updates intended for the
3.17 stream...
For the mac80211 bits, Johannes says:
"The biggest thing here is probably Arik's TDLS rework, beyond that we
have smaller improvements and features like David's scanning IE thing,
Luca's queue work, some CSA work, etc. Also your PID rate control
removal, of course."
For the iwlwifi bits, Emmanuel says:
"I have here a whole bunch of various things. Andy contributes
better debug prints for dvm specific flows and a module parameter to
completely disable power save for dvm. Andrei is sharing the premises
of his work on CSA - more to come. Eran and Liad keep on working
on the new devices. I have the regular amount of BT Coex stuff and
I continue to work on the firmware error report system adding more
debug capabilities. More to come on that subject too."
On top of that, there are some cleanups to the new rsi driver, some
continuing improvements to the rtl818x drivers, and the usual bundles
of updates to ath9k, b43, mwifiex, wil6210, and a few other bits here
and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
load_pointer() is already a static inline function.
Let's move it into filter.h so BPF JIT implementations can reuse this
function.
Since we're exporting this function, let's also rename it to
bpf_load_pointer() for clarity.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compiler warnings:
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvid Brodin says:
====================
net/hsr: Use list_head+rcu, better frame dispatch, etc.
This patch series is meant to improve the HSR code in several ways:
* Better code readability.
* In general, make the code structure more like the net/bridge code (HSR
operates similarly to a bridge, but uses the HSR-specific frame headers to
break up rings, instead of the STP protocol).
* Better handling of HSR ports' net_device features.
* Use list_head and the _rcu list traversing routines instead of array of slave
devices.
* Make it easy to support HSR Interlink devices (for future Redbox/Quadbox
support).
* Somewhat better throughput on non-HAVE_EFFICIENT_UNALIGNED_ACCESS archs, due
to lesser copying of skb data.
The code has been tested in a ring together with other HSR nodes running
unchanged code, on both avr32 and x86_64. There should only be one minor change
in behaviour from a user perspective:
* Anyone using the Netlink HSR_C_GET_NODE_LIST message to dump the internal
node database will notice that the database now also contains the self node.
All patches pass 'checkpatch.pl --ignore CAMELCASE --max-line-length=83
--strict' with only CHECKs, each of which have been deliberately left in place.
The final code passes sparse checks with no output.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If none of the slave interfaces are specified, struct nlattr *data[] may
be NULL. Make sure to check for that.
While I'm at it, fix the horrible error messages displayed when only one
of the slave interfaces isn't specified.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also try to prevent some possible slave dereference race conditions. This is
finalized in the next patch, which abandons the slave array in favour of
a list_head list and list RCU.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the frame receive handler to hsr_slave.c.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ic_dev_xid is only used in ipconfig.c
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD 10Gb Ethernet driver updates
The following series fixes some bugs and provides new/changed support
in the driver.
- Fix a debugfs backward compatibility issue introduced by a previous patch
- Write to the interrupt enablement register, not the status register when
setting MTL interrupts
- Call netif_napi_del whenever the ndo_stop operation is called (to match
the call to netif_napi_add on ndo_open)
- Peformance enhancements:
- Adjusted default coalescing settings
- AXI DMA changes (burst length size and cache settings)
- ioread/iowrite reduction during interrupt
- Napi poll updates
- AXI DMA settings based on device tree property to account for a change in
the ARM64 default cache operations assignment
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header file include/linux/arcdevice.h #defines bool to int, if
bool is not already #defined. However, the files which use that header
file seem to rely on that #define (unconditionally) being in effect:
the prototypes for the functions arcrimi_reset, com20020_reset,
com90io_reset, com90xx_reset (whose addresses are assigned to the
hw.reset member of struct arcnet_local) use int explicitly.
Moreover, that #define is an accident waiting to happen (scenario:
inclusion of arcdevice.h followed by inclusion of some header which
declares function prototypes using bool). Also, #include
<linux/types.h> must appear before #include <linux/arcdevice.h> (the
compiler wouldn't like "typedef _Bool int").
Since none of the files using arcdevice.h declare variables of type
"bool", the patch is actually quite simple, unlike the commit message.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings are no longer relevant. Even when last slave is
removed, there is a valid address assigned to bond (random).
The correct functionality of vlans is ensured by maintaining unicast
list in vlan_sync_address().
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
at86rf230: rework driver implementation
this patch series includes a rework of the at86rf230 driver.
There are several changes:
- Add regmap support.
- Merge at86rf212 operations with generic at86rf2xx operations, all chips
supports these operations.
- Drop of irqworker. This is a workqueue which will scheduled by an irq to
handle synchronous spi handling. Instead using asynchronous spi handling,
then no scheduler is involved at irq handling.
- Also detected some bugs by receiving frame like CRC can be correct and a
802.15.4 frame length could be above 127 bytes. This would crash the whole
kernel (but should be handled by the mac layer). Another bug is the handling
with RX_SAFE_MODE which protect the frame buffer after a readout. This is
currently not working because we read out the buffer twice and the first one
to get the frame size. Solution is to readout always the whole frame buffer.
- Added some timing relevants things from the datasheet for state changes And
IEEE 802.15.4 standard like interframe spacing. Interframe spacing is needed
to insert some receiving space time between frame transmitting. This should be
also handled by MAC layer, but it's currently a workaround to add this inside
the driver layer.
- Add some callback setting for chip specific handling, instead of runtime decisions
if (is_chip_type()). Callbacks are set only once at probe time.
- We don't using a force state change anymore. A force state change will do a
abort of receiving frames while we want to transmit a new frame. This should
decrease the drop rate of packets.
- And many others changes and bug fixes...
changes since v3:
- fix irq polarity in patch ("at86rf230: rework irq_pol setting").
changes since v2:
- add check if necessary functions are implemented when hw flags are set in patch
("mac802154: at86rf230: add hw flags and merge ops"). I choosed the second variant.
- remove unnecessary includes for workqueue and mutex in patch
("at86rf230: rework transmit and receive").
- remove unnecessary cast in patch ("at86rf230: rework transmit and receive").
- acivate regmap cache with REGCACHE_RBTREE in patch
("at86rf230: add regmap support").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
