Tested by Christoph Sager and Tomas Klas
zd1211b chip 0586:3412 v4810 high 00-13-49 AL7230B_RF pa0 g----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for some new ZD1211B devices which ship with
the AL7230B RF.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change allows RF drivers to provide their own 6M band edge patching
implementation, while providing a generic implementation shared by most
currently supported RF's.
The upcoming ZD1211B/AL7230B code will use this to define its own
patching function, which is different from the other RF configurations.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver only does the CR123 write for non-USB devices (which
don't exist on the consumer market)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the changes in the specifications for
2050radio_init that were recently posted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Fri, Mar 30, 2007 at 01:05:59AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.21-rc5-mm2:
>...
> git-netdev-all.patch
>...
> git trees
>...
This patch makes the needlessly global PHY_DEVICES[] static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replacing with time_after in drivers/net/eexpress.c
Applies and compiles clean on latest tree.Not tested.
Signed-off-by: Shani Moideen <shani.moideen@wipro.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no good reason for the asymmetry in the parameters of
eth_port_uc_addr_get() and eth_port_uc_addr_set(). Make them
symmetric. Remove some gratuitous block comments while we're here.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This PHY support patch was written by Benjamin Li.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The baycom_ser_fdx driver did not allow i/o ports >= 0x1000. Now that
there are pci cards (with rs232 ports) which use for example 0xb800 this
limit should not exists.
Also, for non kernel coders find the cause of problems was challenging so I
added extra logging.
Signed-off-by: Folkert van Heusden <folkert@vanheusden.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
strlcpy already accounts for the trailing zero in its length
computation, so there is no need to substract one to the buffer size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <osstklei@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tested by TiCPU on irc
zd1211 chip 13b1:001e v4802 high 00-14-bf AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using monitor mode, Johannes Berg observed out that lots of corrupted
and otherwise invalid frames were being passed to the host.
When in monitor mode we were disabling the hardware filtering here, but
this is not how monitor mode should work.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a backport of Helge Deller's recent patch for wireless-dev.git
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 13 years of use, it looks like my email address is finally going
to disappear. While this is likely to drop the amount of incoming spam
greatly ;-), it may also affect more appropriate messages, so let's
update my email address in various places. In addition, Host AP mailing
list is subscribers-only and linux-wireless can also be used for
discussing issues related to this driver which is now shown in
MAINTAINERS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch includes:
- code cleanup related to resource management
- extended error data gathering for resource management
- removing trailing whitespaces
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch fixes bugs related to the probe / remove adapter
functionality (handling of OFDT nodes)
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NETPOLL support for Sibyte MAC
Signed-off-by: Manish Lachwani <mlachwani@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Remove unused variables from s2io_nic structure
- Changed the memory failure printk messages to print only in debug mode
- Updated the copyright messages
(Resending; due to patch being corrupted)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do some minor rearrangement of data structures to try and optimize
cache usage.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't need to lock when processing transmit complete unless queue fills.
Modeled after tg3.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following hardware error bits only show up on Genesis chipset
and are handled elsewhere, so they can be masked off.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup drivers/net/wireless/libertas/debugfs.c to use standard kernel
macros and functions.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way airo.c keeps track of all its devices is complicated and buggy
as well (del_airo_dev forgets to free the memory add_airo_dev allocates).
It's cleaner to use the standard list primitives.
While we're at it, it's not necessary to put PCI cards in the list, because
the kernel already keeps track of them. We can take advantage of it and
use the .remove callback as it was meant to be.
This makes /sys/bus/pci/drivers/airo/{,un}bind work.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's unnecessary to check for NULL before calling kfree().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In code manipulating the TM State Low register of 802.11 cores, two
different magic numbers are used to reference the 'G Mode Enable' bit.
One of these, 0x20000000, is clear, but the other, (0x800 << 18), is not.
This patch replaces both types with a defined constant. In addition, two
bits in the TM State High registers are given definitions to help in
following the code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ASUS A9Rp
Tested by Serge
zd1211b chip 0b05:171b v4802 high 00-17-31 AL2230_RF pa0 g--
ZyXEL G-202
Tested by Marcus D. Hanwell
zd1211b chip 0586:3410 v4810 high 00-13-49 AL2230_RF pa0 g---
US Robotics USR805423
Tested by Pascal S. de Kloe
FCC ID: RAXWN4501H
zd1211b chip 0baf:0121 v4810 high 00-14-c1 AL2230_RF pa0 g--N
Julien Pinon reports this also comes in AL2230S form
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ZD1211 appears to be back in production: a number of new devices have
been appearing! Some of them are using new radios.
This patch adds support for the next generation AL2230 RF chip which has
been spotted in a few new devices.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Suggested by Maxime Austruy, based on mac80211 changes from Stephen
Hemminger
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rev tulip version... things have changed since 2002!
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a problem with Tulip 21142 HP branded PCI cards (PN#: B5509-66001),
which feature a NatSemi DP83840A PHY.
Without that patch, it is impossible to properly initialize the card's PHY,
and it's thus impossible to monitor/configure it.
[VAL: I'm happy with the 1.5 ms max delay; it doesn't seem excessive.]
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Jim Gifford <maillist@jg555.com>, Grant Grundler <grundler@parisc-linux.org>, Peter Horton <pdh@colonel-panic.org>
With Grant's help I was able to get the tulip driver to work with 64 bit
MIPS.
[VAL: I'm happy with the 1.5 ms max delay; it doesn't seem excessive.]
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tc35815 driver lacks a call to pci_dma_sync_single_for_device() on
receiving. Recent fix of MIPS dma_sync_single_for_cpu() reveal this
bug.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
use netdev_priv() instead of dev->priv
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch below moves the init_block out of the private struct and
only allocates init block with pci_alloc_consistent.
This has two effects:
1. Performance increase for non cache coherent machines, because the
CPU only data in the private struct are now cached
2. locks are working now for platforms, which need to have locks
in cached memory
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A patch to use ARRAY_SIZE macro already defined in kernel.h.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Function `phy_mii_ioctl' returns physical device's information based on
user requests. When requested to return the basic mode control register
information (BMCR), the original implementation only returns the physical
device's duplex information and forgets to return speed information, which
should not be because BMCR register is used to hold both duplex and speed
information.
The patch checks the BMCR value against speed-related flags and fills the
return structure's speed field accordingly.
Signed-off-by: Shan <shanlu@cs.uiuc.edu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for WOL on Magic Packet and on link change
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert function documentation in drivers/net/phy/ to kernel-doc
and add it to DocBook.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the round_jiffies() function in e1000.
These timers all were of the "about once a second" or "about once every X
seconds" variety and several showed up in the "what wakes the cpu up" profiles
that the tickless patches provide. Some timers are highly dynamic based on
network load; but even on low activity systems they still show up so the
rounding is done only in cases of low activity, allowing higher frequency
timers in the high activity case.
The various hardware watchdogs are an obvious case; they run every 2 seconds
but aren't otherwise specific of exactly when they need to run.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current tc35815 driver is very obsolete and less maintained for a long
time. Replace it with a new driver based on one from CELF patch
archive.
Major advantages of CELF version (version 1.23, for kernel 2.6.10) are:
* Independent of JMR3927.
(Actually independent of MIPS, but AFAIK the chip is used only on
MIPS platforms)
* TX4938 support.
* 64-bit proof.
* Asynchronous and on-demand auto negotiation.
* High performance on non-coherent architecture.
* ethtool support.
* Many bugfixes and cleanups.
And improvoments since version 1.23 are:
* TX4939 support.
* NETPOLL support.
* NAPI support. (disabled by default)
* Reduce memcpy on receiving.
* PM support.
* Many cleanups and bugfixes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global vlan_strip_flag static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Thanks to Jö Fahlke for donating hardware.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Forward porting of Ladis' 2.4 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides a functionality that allows parallel
RX processing on multiple RX queues by using dummy netdevices.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces functionality to dynamically add / remove
ehea ports via an userspace DLPAR tool. It creates a subnode for
each logical port in the sysfs.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are several uses of _ops structure in this driver that
can be converted to const.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert some initialized structures to C99 style.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some code for Chelsio 1G boards was put in the driver
based on the vendor version (minus TOE). Well some of those board
versions are only supported with TOE on the vendor driver, so additional
dead code was added.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In bcm43xx_ethtool, UTS_RELEASE is used. Replacing this with utsname()->release
avoids rebuilding this module each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like some of the PC Card manfid/product strings were lost
when Host AP driver was converted to use PCMCIA_DEVICE_* helpers. This
patch adds back D-Link DWL-650 Rev. P1 using the same product ID
string match as the pcmcia-cs/cardmgr configuration used before.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
testing much?
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original macros result in gcc 4.2 warning about "cast from pointer
to integer of different size" on 64-bit systems.
Use of offsetof() on fields in substructures is widespread throughout
the kernel code and should work whether offsetof() is defined using
__compiler_offsetof() or a cast.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch commented that GFP_NOFS should not be used in a
network driver.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 'channels' sysfs entry for ipw2200. The entry exports channels
information for the user space.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just found a hole in my last patch. It was reported to me that shortly after we
integrated this patch. The report was of an oops that took place inside of
netif_rx when using the sis900 driver. Looking at my origional patch I noted
that there was a spot between the new skb_alloc and the refill_rx_ring label
where skb got reassigned to the pointer currently held in the rx_ring for the
purposes of receiveing the frame. The result of this is however that the buffer
that gets passed to netif_rx (if it is called), then gets placed right back into
the rx_ring. So if you receive frames fast enough the skb being processed by
the network stack can get corrupted. The reporter is testing out the fix I've
written for this below (I'm not near my hardware at the moment to test myself),
but I wanted to post it for review ASAP. I'll post test results when I hear
them, but I think this is a pretty straightforward fix. It just uses a separate
pointer to do the rx operation, so that we don't improperly reassign the pointer
that we use to refill the rx ring.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The subsystem rwsem is not used by the driver core at all, so the use of
it in the phy code doesn't make any sense. They might possibly
want to use a local lock, but I am unsure about that.
Cc: netdev <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'e1000-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
e1000: FIX: Stop raw interrupts disabled nag from RT
e1000: FIX: firmware handover bits
e1000: FIX: be ready for incoming irq at pci_request_irq
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
Due to conflicts with the network drivers tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ROUND_UP macro cleanup use DIV_ROUND_UP
Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed tun/tap driver's handling of hw addresses. The hw address is stored
in both the net_device.dev_addr and tun.dev_addr fields. These fields were
not kept synchronized, and in fact weren't even initialized to the same
value. Now during both init and when performing SIOCSIFHWADDR on the tun
device these values are both updated. However, if SIOCSIFHWADDR is
performed on the net device directly (for instance, setting the hw address
using ifconfig), the tun device does not get updated. Perhaps the
tun.dev_addr field should be removed completely at some point, as it is
redundant and net_device.dev_addr can be used anywhere it is used.
Signed-off-by: Brian Braunstein <linuxkernel@bristyle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/hamradio/yam.c: In function `yam_tx_byte':
drivers/net/hamradio/yam.c:643: warning: passing arg 1 of `skb_copy_from_linear_data_offset' from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current e1000_xmit_frame spews raw interrupt disabled nag messages when
used with RT kernel patches. This patch uses spin_trylock_irqsave,
which allows RT patches to properly manage the irq semantics.
Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Upon code inspection it was spotted that the firmware handover bit get/set
mismatched, which may have resulted in management issues on PCI-E
adapters. Setting them correctly may fix some management issues such
as arp routing etc.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
DEBUG_SHIRQ code exposed that e1000 was not ready for incoming interrupts
after having called pci_request_irq. This obviously requires us to finish
our software setup which assigns the irq handler before we request the
irq.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct minor typo in drivers/net/wireless/Kconfig identified by
Stefano Brivio <stefano.brivio@polimi.it>.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppoe_flush_dev() kicks all sockets bound to a device that is going down.
In doing so, locks must be taken in the right order consistently (sock lock,
followed by the pppoe_hash_lock). However, the scan process is based on
us holding the sock lock. So, when something is found in the scan we must
release the lock we're holding and grab the sock lock.
This patch fixes race conditions between this code and pppoe_release(),
both of which perform similar functions but would naturally prefer to grab
locks in opposing orders. Both code paths are now going after these locks
in a consistent manner.
pppoe_hash_lock protects the contents of the "pppox_sock" objects that reside
inside the hash. Thus, NULL'ing out the pppoe_dev field should be done
under the protection of this lock.
Signed-off-by: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
below you find a patch that fixes a memory leak when a PPPoE socket is
release()d after it has been connect()ed, but before the PPPIOCGCHAN ioctl
ever has been called on it.
This is somewhat of a security problem, too, since PPPoE sockets can be
created by any user, so any user can easily allocate all the machine's
RAM to non-swappable address space and thus DoS the system.
Is there any specific reason for PPPoE sockets being available to any
unprivileged process, BTW? After all, you need a packet socket for the
discovery stage anyway, so it's unlikely that any unprivileged process
will ever need to create a PPPoE socket, no? Allocating all session IDs
for a known AC is a kind of DoS, too, after all - with Juniper ERXes,
this is really easy, actually, since they don't ever assign session ids
above 8000 ...
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
below you find a patch that (hopefully) fixes a race between an interface
going down and a connect() to a peer on that interface. Before,
connect() would determine that an interface is up, then the interface
could go down and all entries referring to that interface in the
item_hash_table would be marked as ZOMBIEs and their references to
the device would be freed, and after that, connect() would put a new
entry into the hash table referring to the device that meanwhile is
down already - which also would cause unregister_netdevice() to wait
until the socket has been release()d.
This patch does not suffice if we are not allowed to accept connect()s
referring to a device that we already acked a NETDEV_GOING_DOWN for
(that is: all references are only guaranteed to be freed after
NETDEV_DOWN has been acknowledged, not necessarily after the
NETDEV_GOING_DOWN already). And if we are allowed to, we could avoid
looking through the hash table upon NETDEV_GOING_DOWN completely and
only do that once we get the NETDEV_DOWN ...
mostrows:
pppoe_flush_dev is called on NETDEV_GOING_DOWN and NETDEV_DOWN to deal with
this "late connect" issue. Ideally one would hope to notify users at the
"NETDEV_GOING_DOWN" phase (just to pretend to be nice). However, it is the
NETDEV_DOWN scan that takes all the responsibility for ensuring nobody is
hanging around at that time.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
below is a patch that just removes dead code/initializers without any
effect (first access is an assignment) that I stumbled accross while
reading the source.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty added a new 'stats' field to struct net_device.
loopback driver can use it instead of declaring another struct
net_device_stats This saves some memory.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When csum_offset was introduced we did a conversion from csum to
csum_offset where applicable. A couple of drivers were missed in
this process.
It was harmless to begin with since the two fields coincided. Now
that we've made them different with the addition of csum_start, the
missed drivers must be converted or they can't send packets out at
all that require checksum offload.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
We have to put back the cast to "char *" because these
pointers are volatile.
Reported by Andrew Morton.
Signed-off-by: David S. Miller <davem@davemloft.net>
Network drivers which keep stats allocate their own stats structure
then write a get_stats() function to return them. It would be nice if
this were done by default.
1) Add a new "stats" field to "struct net_device".
2) Add a new feature field to say "this driver uses the internal one"
3) Have a default "get_stats" which returns NULL if that feature not set.
4) Change callers to check result of get_stats call for NULL, not if
->get_stats is set.
This should not break backwards compatibility with older drivers, yet
allow modern drivers to shed some boilerplate code.
Lightly tested: works for a modified lguest network driver.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reducing the number of skb->data direct accesses.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At that point it is equivalent to what was being used, skb->end - skb->data,
and the need is clearly the one skb_tailroom satisfies.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC SuperIO Chip LPC47N227 used for IrDA is not detected because its device
identification byte can be 0x7A instead of 0x5A.
Patch from Peter Kovar <peter.kovar@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming skb->h to skb->transport_header, skb->nh to skb->network_header and
skb->mac to skb->mac_header, to match the names of the associated helpers
(skb[_[re]set]_{transport,network,mac}_header).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->h.raw - skb->nh.raw", similar to skb->mac_len,
that is precalculated tho, don't think we need to bloat skb with one more
member, so just use this new helper, reducing the number of non-skbuff.h
references to the layer headers even more.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->nh.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->nh.raw accessors.
Also do some really obvious simplifications in pppoe_recvmsg, well the
kfree_skb one is not so obvious, but free() and kfree() have the same behaviour
(hint :-) ).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where we want to set skb->mac.raw to an offset from skb->data.
Simple cases first, the memmove ones and specially pktgen will be left for later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all the _type_trans routines are consistent in this regard.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tweak a register setting to prevent the tx mailbox from halting.
Update version to 1.5.8.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64:
drivers/net/hamradio/baycom_ser_fdx.c: In function `ser12_open':
drivers/net/hamradio/baycom_ser_fdx.c:417: error: `NR_IRQS' undeclared (first us
e in this function)
drivers/net/hamradio/baycom_ser_fdx.c:417: error: (Each undeclared identifier is
reported only once
drivers/net/hamradio/baycom_ser_fdx.c:417: error: for each function it appears i
n.)
Cc: Folkert van Heusden <folkert@vanheusden.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sis900 driver appears to have a bug in which the receive routine
passes the skbuff holding the received frame to the network stack before
refilling the buffer in the rx ring. If a new skbuff cannot be allocated, the
driver simply leaves a hole in the rx ring, which causes the driver to stop
receiving frames and become non-recoverable without an rmmod/insmod according to
reporters. This patch reverses that order, attempting to allocate a replacement
buffer first, and receiving the new frame only if one can be allocated. If no
skbuff can be allocated, the current skbuf in the rx ring is recycled, dropping
the current frame, but keeping the NIC operational.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch fixes a kernel bug in depca_platform_probe().
We don't use a dynamic pointer for pldev->dev.platform_data, so it seems
that the correct way to proceed if platform_device_add(pldev) fails is
to explicitly set the pldev->dev.platform_data pointer to NULL, before
calling the platform_device_put(pldev), or it will be kfree'ed by
platform_device_release().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
USRobotics Wireless Adapter (Model 5423) works well with current
zd1211rw driver also (i have tested 2.6.18, 2.6.20 and 2.6.21-rc7).
It just needs its ID added to the list of devices.
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAC address assignment at module loading is simply forgotten.
The bug at module unloading is caused by an incorrect call.
The bug at module unloading does not only happen for sunqe,
sunlance and sunhme (sbus) suffer from it too.
I've tested this on my SS20.
Signed-off-by: Marcel van Nies <morcles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 60cba200f1. It's been
linked to lockups of the e1000 hardware, see for example
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229603
but it's likely that the commit itself is not really introducing the
bug, but just allowing an unrelated problem to rear its ugly head (ie
one current working theory is that the code exposes us to a hardware
race condition by decreasing the amount of time we spend in each NAPI
poll cycle).
We'll revert it until root cause is known. Intel has a repeatable
reproduction on two different machines and bus traces of the hardware
doing something bad.
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Paul Mackerras <paulus@samba.org>
This fixes:
Subject: kernel BUG at net/core/skbuff.c in linux-2.6.21-rc6
process_input_packet() treats the case where the first byte is 0xff
(PPP_ALLSTATIONS) but the second byte is 0x03 (PPP_UI) as indicating a
packet with a PPP protocol number of 0xff. Arguably that's wrong
since PPP protocol 0xff is reserved, and the RFC does envision the
possibility of receiving frames where the control field has values
other than 0x03.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Yukon FE (100mbit only) chips do not support large packets.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to make sure and disable ASF on all chip types. Otherwise, there may be
random reboots.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This device is having all sorts of problems that lead to data corruption
and system instability. It gets receive status and data out of order,
it generates descriptor and TSO errors, etc.
Until the problems are resolved, it should not be used by anyone
who cares about there system.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The basic structure of "normal" UDP/IP/Ethernet
frames (that actually work):
- It starts with the Ethernet header (dest MAC, src MAC, etc.)
- The next part is occupied by the IP header (version info, length of
packet, id=0, fragment offset=0, checksum, from / to address, etc.)
- Then comes the UDP header (src / dest port, length, checksum)
- Actual payload
- Ethernet checksum
Now what's different for IP fragment:
- The IP header has id set to some value (same for all fragments),
offset is set appropriately (i.e. 0 for first fragment, following
according to size of other fragments), size is the length of the frame.
- UDP header is unchanged. I.e. length is according to full UDP
datagram, not just the part within the actual frame! But this is only
true within the first frame: all following frames don't have a valid
UDP-header at all.
The spidernet silicon seems to be quite intelligent: It's able to
compute (IP / UDP / Ethernet) checksums on the fly and tests if frames
are conforming to RFC -- at least conforming to RFC on complete frames.
But IP fragments are different as explained above:
I.e. for IP fragments containing part of a UDP datagram it sees
incompatible length in the headers for IP and UDP in the first frame
and, thus, skips this frame. But the content *is* correct for IP
fragments. For all following frames it finds (most probably) no valid
UDP header at all. But this *is* also correct for IP fragments.
The Linux IP-stack seems to be clever in this point. It expects the
spidernet to calculate the checksum (since the module claims to be able
to do so) and marks the skb's for "normal" frames accordingly
(ip_summed set to CHECKSUM_HW).
But for the IP fragments it does not expect the driver to be capable to
handle the frames appropriately. Thus all checksums are allready
computed. This is also flaged within the skb (ip_summed set to
CHECKSUM_NONE).
Unfortunately the spidernet driver ignores that hints. It tries to send
the IP fragments of UDP datagrams as normal UDP/IP frames. Since they
have different structure the silicon detects them the be not
"well-formed" and skips them.
The following one-liner against 2.6.21-rc2 changes this behavior. If the
IP-stack claims to have done the checksumming, the driver should not
try to checksum (and analyze) the frame but send it as is.
Signed-off-by: Norbert Eicker <n.eicker@fz-juelich.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove assumption that PHY interrupts use GPIOs 3 and 5.
Deal with PHY interrupts connected to any GPIO pins.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reuse the incoming skb when a clientless abort req is recieved.
The release of RDMA connections HW resources might be deferred in
low memory situations.
Ensure that no further activity is passed up to the RDMA driver
for these connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the Intel 5000 southbridge (aka Intel 6310/6311/6321ESB) PCIe ports
and the Intel E30x0 chipsets to the whitelist of aligned PCIe completion.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simpler way of dealing with the firmware 4KB boundary crossing
restriction for rx buffers. This fixes a variety of memory
corruption issues when using an "uncommon" MTU with a 16KB
page size.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to rework wake on lan code to setup properly and get activated
on shutdown (and suspend), not when ethtool is run.
This does not need to go to stable queue because wake on lan
was not even included in 2.6.20 (or earlier versions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of these chips are disabled until clock is enabled.
This fixes:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down, otherwise it can
confuse bonding and bridging and looks like carrier is on immediately
when it is brought back up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The specifications for loopback_gain calculation and for G PHY
initialization have been updated. This patch implements them and
fixes a machine check error that occurs for PPC architecture with a
phy->rev of 1.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 802.11b/g mode, bcm43xx actively scans channels 1-14 no matter what
locale has been set, either in the sprom or by the locale option. This
behaviorviolates regulatory rules everywhere in the world except
Japan. This patch changes the default range to the correct value if the
locale has been set, and to channels 1-13 if no locale has been set.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to conflicting/confusing defines in the vendor driver, we were
reading E2P_PHY_REG from the wrong location.
CR157 patching was slightly incorrect in that the vendor driver only
patches in an 8-bit value, whereas we were patching 24 bits.
Additionally, CR157 patching was happening on both zd1211 and zd1211b,
but this should only happen on zd1211.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw currently detects AL2230S-based devices as AL2230, and hence
programs the RF incorrectly. Transmit silently fails on this
misconfiguration.
After this patch, AL2230S devices are rejected with an error message, to
avoid any confusion with an apparent driver bug.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spin_lock calls made in dev->open and dev->close must disable
BH since open/close are made in process context. Conversely, the
call in dev->hard_start_xmit does not need to disable BH since it
is already executing with BH disabled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages. This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call. However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.
Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.
Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset. It was missing logic to round the
length to 4 bytes.
The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.
Update version to 1.5.7.
Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
