As reported by Stephen Rothwell.
drivers/net/tulip/uli526x.c: In function 'uli526x_rx_packet':
drivers/net/tulip/uli526x.c:861: warning: assignment makes pointer from integer without a cast
Signed-off-by: David S. Miller <davem@davemloft.net>
This is quite similar to b39fe41f48
though said registers are not even documented as 64-bit registers
- as opposed to the initial TxDescStartAddress ones - but as single
bytes which must be combined into 32 bits at the MMIO read/write
level before being merged into a 64 bit logical entity.
Credits go to Ben Hutchings <ben@decadent.org.uk> for the MAR
registers (aka "multicast is broken for ages on ARM) and to
Timo Teräs <timo.teras@iki.fi> for the MAC registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
*add new id (Allied Telesis LM33-PCM-T Lan&Modem multifunction card)
*use PROD_ID for LA-PCM.(because LA-PCM and LM33-PCM-T use the same MANF_ID).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Round-robin (mode 0) does nothing to ensure that any multicast traffic
originally destined for the host will continue to arrive at the host when
the link that sent the IGMP join or membership report goes down. One of
the benefits of absolute round-robin transmit.
Keeping track of subscribed multicast groups for each slave did not seem
like a good use of resources, so I decided to simply send on the
curr_active slave of the bond (typically the first enslaved device that
is up). This makes failover management simple as IGMP membership
reports only need to be sent when the curr_active_slave changes. I
tested this patch and it appears to work as expected.
Originally reported by Lon Hohberger <lhh@redhat.com>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Lon Hohberger <lhh@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports
seen at half duplex. This had the effect of overriding user set values
on link change/reset. Testing shows that adjusting only the timeout
factor is sufficient to prevent Tx hang reports at half duplex.
This patch removes all instances of tx_queue_len in the driver.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cache is unresolved, c->mf[6]c_parent is set to 65535 and
minvif, maxvif are not initialized, hence we must avoid to
parse IIF and OIF.
A second problem can happen when the user dumps a cache entry
where a VIF, that was referenced at creation time, has been
removed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the offline diagnostic tests check to see if any VFs are
online. If so then only run the link test. This is necessary because
the VFs running in guest VMs aren't aware of when the PF is taken
offline for a diagnostic test. Also put a message to the system log
telling the system administrator to take the VFs offline manually if
(s)he wants to run a full diagnostic. Return 1 on each of the tests
not run to alert the user of the condition.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously checking the wrong bits in the MANC register to determine
if managability was enabled. As a result it was incorrectly powering down and
resetting the phy when it didn't need to.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
be_ethtool.c:493: warning: integer constant is too large for 'long' type
be_ethtool.c:493: warning: integer constant is too large for 'long' type
Signed-off-by: Zhitong Wang <zhitong.wangzt@alibaba-inc.com>
Acked-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new flag MSG_WAITFORONE for the recvmmsg() syscall.
When this flag is specified for a blocking socket, recvmmsg()
will only block until at least 1 packet is available. The
default behavior is to block until all vlen packets are
available. This flag has no effect on non-blocking sockets
or when used in combination with MSG_DONTWAIT.
Signed-off-by: Brandon L Black <blblack@gmail.com>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
This patch removes all instances of tx_queue_len in the driver.
Originally reported and patched by Franco Fichtner
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need in getting it 3 times and gcc isn't smart enough
to understand this himself.
This is just a cleanup before the fix (next patch).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Fix undo of reserve() before RX recycle
gfar_new_skb reserve()s space in the SKB to align it. If an error occurs,
and the skb needs to be returned to the RX recycle queue, the current code
attempts to reset head, but did not reset tail. This patch remembers the
alignment amount, and reverses the reserve() when needed.
Signed-off-by: Ben Menchaca <ben@bigfootnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During FCF solicitation, the switch is supposed to pad the
solicited advertisement out to the endpoints specified
maximum FCoE frame size. That means that we need to receive
FIP frames that are larger than the standard MTU. To make
sure the receive queue is configured correctly, we should be
filtering FIP traffic into the FCoE queues.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently FIP (FCoE Initialization Protocol) frames
are going untagged. This causes various problems
with FCFs (switches) that have negotiated a priority
over dcbx. This patch tags FIP frames with the same
priority as the FCoE frames.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user buffer count was 256 the shift would place a 1
in the offset region leading to errors. It also overwrites
the uers buffer list. This patch makes sure that at most
256 user buffers are allowed for DDP and the buffer count
is masked properly such that it doesn't overwrite the offset
when shifting the bits.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the last patch I missed an unecessary min_t comparison.
This patch removes it, the path allocates at most
72 tx queues for 82599 and 24 for 82598 there is no need
for this check.
Additionally this sets MAX_[TX|RX]_QUEUES to 72. Which is
used as the size for the tx/rx_ring arrays. There is no
reason to have more tx_rings/rx_rings then num_tx_queues.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clear_to_send flag is being cleared before the call to ping all
the VFs. It should be called after pinging all the VFs.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs running in guest VMs do not respond in as timely a manner to
PF indication it is going down as they do when running in the host
domain. If the adapter is in SR-IOV mode insert a two second delay
to guarantee that all VFs have had time to respond to the PF reset.
In any case resetting the PF while VFs are active should be
discouraged but if it must be done then there will be a two
second delay to help synchronize resets among the PF and all the
VFs.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Tx mapping function if a DMA error occurred then the unwind of
previously mapped sections would improperly check an unsigned int if
it was less than zero. Changed the index variable to signed to avoid
the error.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Return value of ioremap is not checked, NULL check added.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
crb_intr_mask/crb_sts_consumer is predefined for NX2031 not for
NX3031. For NX3031, these values get defined in rx context creation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bios sub version from unified fw image is calculated incorrect.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3531768883.
People are reporting problems due to this change and there
is no anticipation that the cause will be tracked down
any time soon.
We can try next time to selectively re-enable this based upon chip
type, or have a black list of some sort.
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling this driver gave a section mismatch,
so I reviewed the init/exit paths of the driver
and made the correct changes.
WARNING: drivers/isdn/hisax/built-in.o(.text+0x55e37): Section mismatch
in reference from the function elsa_cs_config() to the function
.devinit.text:hisax_init_pcmcia()
The function elsa_cs_config() references
the function __devinit hisax_init_pcmcia().
This is often because elsa_cs_config lacks a __devinit
annotation or the annotation of hisax_init_pcmcia is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling this driver gave a section mismatch,
so I reviewed the init/exit paths of the driver
and made the correct changes.
WARNING: drivers/isdn/hisax/built-in.o(.text+0x56512): Section mismatch
in reference from the function avma1cs_config() to the function
.devinit.text:hisax_init_pcmcia()
The function avma1cs_config() references
the function __devinit hisax_init_pcmcia().
This is often because avma1cs_config lacks a __devinit
annotation or the annotation of hisax_init_pcmcia is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling this driver gave a section mismatch,
so I reviewed the init/exit paths of the driver
and made the correct changes.
WARNING: drivers/isdn/hisax/built-in.o(.text+0x56bfb): Section mismatch
in reference from the function teles_cs_config() to the function
.devinit.text:hisax_init_pcmcia()
The function teles_cs_config() references
the function __devinit hisax_init_pcmcia().
This is often because teles_cs_config lacks a __devinit
annotation or the annotation of hisax_init_pcmcia is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling this driver gave a section mismatch,
so I reviewed the init/exit paths of the driver
and made the correct changes.
WARNING: drivers/isdn/hisax/built-in.o(.text+0x558d6): Section mismatch
in reference from the function sedlbauer_config() to the function
.devinit.text:hisax_init_pcmcia()
The function sedlbauer_config() references
the function __devinit hisax_init_pcmcia().
This is often because sedlbauer_config lacks a __devinit
annotation or the annotation of hisax_init_pcmcia is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A missing break statement in hashlimit_ipv6_mask(), and masks
between /64 and /95 are not working at all...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The order of the IPv6 raw table is currently reversed, that makes impossible
to use the NOTRACK target in IPv6: for example if someone enters
ip6tables -t raw -A PREROUTING -p tcp --dport 80 -j NOTRACK
and if we receive fragmented packets then the first fragment will be
untracked and thus skip nf_ct_frag6_gather (and conntrack), while all
subsequent fragments enter nf_ct_frag6_gather and reassembly will never
successfully be finished.
Singed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If dl_seq_start() memory allocation fails, we crash later in
dl_seq_stop(), trying to kfree(ERR_PTR(-ENOMEM))
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The original code saved the error value but just returned 0 in the end.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma map fields in the skb_shared_info structure no longer has any users
and can be dropped since it is making the skb_shared_info unecessarily larger.
Running slabtop show that we were using 4K slabs for the skb->head on x86_64 w/
an allocation size of 1522. It turns out that the dma_head and dma_maps array
made skb_shared large enough that we had crossed over the 2k boundary with
standard frames and as such we were using 4k blocks of memory for all skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates real_num_tx_queues in case underlying real device
has changed real_num_tx_queues.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comment:-
-- adds BUG_ON to catch case of real_num_tx_queues exceeding num_tx_queues.
-- created this self contained patch to just update real_num_tx_queues.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to correctly select vlan tx queue for a driver
supporting multi tx queue with ndo_select_queue implemented since
currently selected vlan tx queue is unaligned to selected queue by
real net_devce ndo_select_queue.
Unaligned vlan tx queue selection causes thrash with higher vlan
tx lock contention for least fcoe traffic and wrong socket tx
queue_mapping for ixgbe having ndo_select_queue implemented.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comments, mirrored
vlan net_device_ops to have them with and without vlan_dev_select_queue
and then select according to real dev ndo_select_queue present or not
for a vlan net_device. This is to completely skip vlan_dev_select_queue
calling for real net_device not supporting ndo_select_queue.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that vlan_gro_receive is only used if vlans have been
registered to the adapter structure. Previously we were just sending all vlan
tagged frames in via this function but this results in a null pointer
dereference when vlans are not registered.
[ This fixes bugzilla entry 15582 -Eric Dumazet]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't aggregate rx_no_buffer_count into rx_fifo_errors. RNBC counts
packets that get queued temporarily in the adapter's FIFO. These
packets are not dropped and are not errors. The correct counter
is rx_missed_errors (MPC).
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netpoll needs to call the proper handler depending on the IRQ mode
and the vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver calls netif_napi_add() for all the NAPI structs during
->probe() time but not all of them will be used if we're not in MSI-X
mode. This creates a problem for netpoll since it will poll all the
NAPI structs in the dev_list whether or not they are scheduled, resulting
in a crash when we access structure fields not initialized for that vector.
We fix it by moving the netif_napi_add() call to ->open() after the number
of IRQ vectors has been determined.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
