Adds LED drivers for LEDs found on the Sharp Zaurus c7x0 (corgi, shepherd,
husky) and cxx00 (akita, spitz, borzoi) models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an LED trigger for the charger status as found on the Sharp Zaurus series
of devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
Adapt xsc3 to the changes in 74945c8616
(xsc3 was written before but merged after the latter went in.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Provide Cirrus EP93xx AMBA PL010 serial support.
[SERIAL] amba-pl010: allow platforms to specify modem control method
[SERIAL] Remove obsoleted au1x00_uart driver
[SERIAL] Small time UART configuration fix for AU1100 processor
Patch from Paul Brook
The example code in the source documentation for __kernel_dmb
clobbers r0 but doesn't list it the asm clobber list.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Intel ixp23xx series of CPUs. The
ixp23xx is an XSC3 based CPU with 512K of L2 cache, a 64bit 66MHz PCI
interface, two DDR RAM interfaces, QDR RAM interfaces, two gigabit
MACs, two 10/100 MACs, expansion bus, four microengines, a Media and
Switch Fabric unit almost identical to the one on the ixp2400, two
xscale (8250ish) UARTs and a bunch of other stuff.
This patch adds the core ixp23xx support code, and support for the
ADI Engineering Roadrunner, Intel IXDP2351, and IP Fabrics Double
Espresso platforms.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for the LogicPD PXA270 Card Engine.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add ixp23xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the new XScale v3 core. This is an
ARMv5 ISA core with the following additions:
- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)
I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.
L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.
There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As per the corresponding change to the serial drivers, arrange
for ARM decompressors to give CRLF. Move the common putstr code
into misc.c such that machines only need to supply "putc" and
"flush" functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an RTC subsystem driver for the ARM SA1100/PXA2XX processor RTC.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some namespace conflicts between the RTC subsystem and the ARM Integrator
time functions.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes from the ARM subsytem some of the rtc-related functions
that have been included in the RTC subsystem. It also fixes some naming
collisions.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ifeq ($CONFIG_PREEMPT,y) -> ifeq ($(CONFIG_PREEMPT),y)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Mouw
The LART website moved to http://www.lartmaker.nl/. This patch
updates the URL in ARM specific files.
Signed-off-by: Erik Mouw <erik@bitwizard.nl>
Acked-by: Jan-Derk Bakker <jdb@lartmaker.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The high page vector (0xFFFF0000) does not supported in nommu mode.
This patch allows the vectors to be 0x00000000 or the begining of DRAM
in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds Kconfig-nommu for noMMU specific configurations
and MMUEXT variable into Makefile.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nommu version start-up code head-nommu.S.
The common part of the start-up codes is moved to head-common.S.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds MPU support in boot/compressed/head.S.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The amba-pl010 hardware does not provide RTS and DTR control lines; it
is expected that these will be implemented using GPIO. Allow platforms
to supply a function to implement manipulation of modem control lines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add an EXPORT_SYMBOL for the Akita IO Expander Device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3030/2: fix permission check in the obscur cmpxchg syscall
[ARM] nommu: rename compressed/head.S symbols to a new style
[ARM] select TLS_REG_EMUL and NEEDS_SYSCALL_FOR_CMPXCHG
[ARM] nommu: Move hardware page table definitions to pgtable-hwdef.h
[ARM] Move read of processor ID out of lookup_processor_type()
[ARM] Fix typo in tlbflush.h
[ARM] noMMU: removes TLB codes in nommu mode
[ARM] noMMU: block sys_fork in nommu mode
[ARM] 3399/1: Fix link problem when CONFIG_PRINTK is disabled
[ARM] 3398/1: Fix the VFP registers loading/storing base address
[ARM] 3397/1: AT91RM9200 Header update
[ARM] 3385/1: Battery support for sharp zaurus sl-5500 (collie)
[ARM] SMP: don't set cpu_*_map in smp_prepare_boot_cpu
include/linux/clk.h is betraying its ARM origins
[ARM] Move enable_irq and disable_irq to assembler.h
[ARM] 3391/1: use PLAT8250_DEV_PLATFORM{,1} for platform device id instead of 0/1
Patch from Lennert Buytenhek
Add a PLAT8250_DEV_PLATFORM2, and convert the two ixdp2x01 CPLD serial
ports to use platform serial devices with ids PLAT8250_DEV_PLATFORM[12].
(The on-chip xscale UART is PLAT8250_DEV_PLATFORM, id #0.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Quoting RMK:
|pte_write() just says that the page _may_ be writable. It doesn't say
|that the MMU is programmed to allow writes. If pte_dirty() doesn't
|return true, that means that the page is _not_ writable from userspace.
|If you write to it from kernel mode (without using put_user) you'll
|bypass the MMU read-only protection and may end up writing to a page
|owned by two separate processes.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Malcolm Parsons
Printking a backtrace requires printk, so disable backtrace code
when printk is disabled.
Without this patch, a kernel with CONFIG_PRINTK disabled does not link:
arch/arm/lib/lib.a(backtrace.o): In function `c_backtrace':
arch/arm/lib/backtrace.S:(.text+0x108): undefined reference to `printk'
arch/arm/lib/backtrace.S:(.text+0x11c): undefined reference to `printk'
arch/arm/lib/lib.a(backtrace.o):(.fixup+0x8): undefined reference to `printk'
Signed-off-by: Malcolm Parsons <malcolm.parsons@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The current VFP code corrupts the VFP registers (including the control
ones) if more than one floating point application is executed at the same
time. This patch fixes the updating of the load/store base addresses for
the VFP registers.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
This adds support for battery reading on collie. Collie slowly charges
battery even with charging disabled, so I did not yet enable fast
charge.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recent addition of boot_cpu_init() implements the initialisation
of the online, present and possible cpu maps for the boot CPU, so
there is no reason to duplicate this in the architecture
smp_prepare_boot_cpu() hook.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/sam/kbuild: (46 commits)
kbuild: remove obsoleted scripts/reference_* files
kbuild: fix make help & make *pkg
kconfig: fix time ordering of writes to .kconfig.d and include/linux/autoconf.h
Kconfig: remove the CONFIG_CC_ALIGN_* options
kbuild: add -fverbose-asm to i386 Makefile
kbuild: clean-up genksyms
kbuild: Lindent genksyms.c
kbuild: fix genksyms build error
kbuild: in makefile.txt note that Makefile is preferred name for kbuild files
kbuild: replace PHONY with FORCE
kbuild: Fix bug in crc symbol generating of kernel and modules
kbuild: change kbuild to not rely on incorrect GNU make behavior
kbuild: when warning symbols exported twice now tell user this is the problem
kbuild: fix make dir/file.xx when asm symlink is missing
kbuild: in the section mismatch check try harder to find symbols
kbuild: fix section mismatch check for unwind on IA64
kbuild: kill false positives from section mismatch warnings for powerpc
kbuild: kill trailing whitespace in modpost & friends
kbuild: small update of allnoconfig description
kbuild: make namespace.pl CROSS_COMPILE happy
...
Trivial conflict in arch/ppc/boot/Makefile manually fixed up
This adds missing bits of collie (sharp sl-5500) PCMCIA support and
MFD support.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch renames symbols to a new style to prepare mpu support
code merging. e.g. __armv4_cache_on --> __armv4_mmu_cache_on
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
5d25ac038a broke VFP builds due to
enable_irq not being defined as an assembly macro. Move it to
assembler.h so everyone can use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch changes iop3xx and omap2 and to use PLAT8250_DEV_PLATFORM{,1}
as platform device id instead of just hardcoding 0/1 directly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
I found a typo and what seems to be a run-on sentence in
arch/arm/common/dmabounce.c
This patch corrects both.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Unify the five existing ixp2000 defconfigs into one defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
ixp2000 used to initially mark GPIO interrupts as invalid, and not
mark them valid until set_irq_type() was called, but this doesn't
work if you want to use request_irq() with the SA_TRIGGER_* flags.
So, just mark the GPIO interrupts valid from the beginning. We
configure GPIOs as inputs when set_irq_type() is called anyway, so
this shouldn't be a problem.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have an explicit mm call to split higher order pages into individual pages.
Should help to avoid bugs and be more explicit about the code's intention.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only issue a "nobody cared" warning after 99900 spurious interrupts.
This avoids the occasional spurious interrupt causing warnings, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need this to be zero initialised. Since this is an array, use kcalloc
rather than kzalloc or kmalloc.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add Simtec Osiris to the default build, and enable the
USB-OHCI section by default.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the build of arch/arm/mach-s3c2410/mach-osiris.c
and fix the warnings from sparse.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add GPIO interrupt support for the first 16 GPIO lines (port A
and B.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add USB bus clock definition for 48MHz fed to OHCI and gadget cores
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add set_rate methods for the extra clocks on the S3C2440
and add the camera UPLL clock source
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add support for clk_set_rate and clk_round_rate to the
s3c2410 clock implementation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add ep93xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for setting the direction of and getting/setting the
value of the 64 GPIO lines.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus ep93xx series of CPUs. The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.
This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
ixp4xx_config_irq did not configure the gpio line
as an input.
As an added bonus, the irq2gpio array has been converted
from int to char.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Peter Teichmann
Currently, if the kernels HZ value is greater than 100, delays with the udelay function are too short. This can cause trouble for instance with the zd1201 usb wlan driver.
This patch suggests a solution that keeps the overhead small and maintains (hopefully) sufficient resolution.
Signed-off-by: Peter Teichmann
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for Intel's IXDP28x5 platform. This
is just and IXDP2801 with a new CPU rev but the bootloader
has been updated to reflect a new machine ID so we just build
support for it by default when we build IXDP2801.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add enable and set_parent calls for the dclk
and clkout clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add clk_set_parent() call to clock code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the UPLL clock registration to the central
clock file, and add an enable method
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add selection for timer code for the Simtec Osiris
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Support for Simtec IM2440D20 CPU modules (Osiris)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
There is no reference to it anymore so remove it at last.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs have multiple VIC devices. Adapt the generic vic code
to allow multiple implementations to be handled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the individual coprocessor handlers to decide when to enable
interrupts, rather than unconditionally enabling them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, OMAP platforms without the 32K timer left HZ set to
an empty value. Fix this by making the dependency on OMAP_32K_TIMER
rather than OMAP_32K_TIMER_HZ.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/arch/irq.h used to be included from asm/irq.h, but was removed
from the ARM kernel a long time ago. Consequently, the contents
of asm/arch/irq.h (which mostly contain a definition for fixup_irq())
have not been used. Hence, remove asm/arch/irq.h.
Some machine support files incorrectly included this file, making
little or no use of the contents. Move the contents to a local
include file, and remove those include statements as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Read the processor ID at boot, and save it in "processor_id" as we
did before. Later, when we re-parse the CPU type in the setup.c code,
re-use the value stored in "processor_id".
This allows a cleaner work-around for noMMU devices without CP#15.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sys_fork is not supported in nommu mode. The other syscalls
that is not supported in nommu mode are to be defined as cond_signal
in kernel/sys_ni.c.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (23 commits)
[PATCH] sysfs: fix a kobject leak in sysfs_add_link on the error path
[PATCH] sysfs: don't export dir symbols
[PATCH] get_cpu_sysdev() signedness fix
[PATCH] kobject_add_dir
[PATCH] debugfs: Add debugfs_create_blob() helper for exporting binary data
[PATCH] sysfs: fix problem with duplicate sysfs directories and files
[PATCH] Kobject: kobject.h: fix a typo
[PATCH] Kobject: provide better warning messages when people do stupid things
[PATCH] Driver core: add macros notice(), dev_notice()
[PATCH] firmware: fix BUG: in fw_realloc_buffer
[PATCH] sysfs: kzalloc conversion
[PATCH] fix module sysfs files reference counting
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to USB subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to RCU subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE()
[PATCH] Clean up module.c symbol searching logic
[PATCH] kobj_map semaphore to mutex conversion
[PATCH] kref: avoid an atomic operation in kref_put()
[PATCH] handle errors returned by platform_get_irq*()
[PATCH] driver core: platform_get_irq*(): return -ENXIO on error
...
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Catalin Marinas
Chosing of the CLCD RGB mode is no longer possible via the SYS_CLCD
register on the RealView boards. Instead, this configuration is done in the
CLCD primecell control register directly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/kernel/setup.c declares mem_fclk_21285 when
this is already declared in include/asm-arm/system.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/kernel/compat.c exports two functions,
convert_to_tag_list and squash_mem_tags which
are not defined in any header files, and not
used outside arch/arm/kernel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the following warnings from sparse:
arch/arm/kernel/process.c:86:6: warning: symbol 'default_idle' was not declared. Should it be static?
arch/arm/kernel/process.c:378:5: warning: symbol 'dump_fpu' was not declared. Should it be static?
Include <linux/elfcore.h> for dump_fpu() decleration, and
make default_idle() static as it is not used outside the file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Albrecht Dre
Add DMA resources to s3c2410 spi platform devices - dma_(alloc|free)_coherent should now work as expected.
Signed-off-by: Albrecht Dre <albrecht.dress@lios-tech.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
Enable frontlight during collie bootup, so that display is actually
readable in anything other than bright sunlight.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the reliance of iwmmxt on hand coded alignments.
Since thread_info is always 8K aligned, specifying that fpstate is
8-byte aligned achieves the same effect without needing to resort
to hand coded alignments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patches add the 1-wire drivers
to the ARM Kconfig.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
ARM1136 erratum 371025 (category 2) specifies that, under rare
conditions, an invalidate I-cache by MVA (line or range) operation can
fail to invalidate a cache line. The recommended workaround is to
either invalidate the entire I-cache or invalidate the range by
set/way rather than MVA.
Note that for a 16K cache size, invalidating a 4K page by set/way is
equivalent to invalidating the entire I-cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The patch that would have made the NSLU2
kernel non compatible with other ixp4xx machs
never entered the kernel. So it is actually
safe to remove the prompt dependencies.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
Disable GPIO clocks to allow
the power led to work properly.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When shifting the low-parts of signed numbers, a logical shift
should be used to avoid sign-extending a bit which isn't a sign
bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
nas100d_power_exit(void) gets some protection
to avoid freeing an irq when it is not appropriate to do so.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Also from Thomas Gleixner <tglx@linutronix.de>
Function next_timer_interrupt() got broken with a recent patch
6ba1b91213 as sys_nanosleep() was moved to
hrtimer. This broke things as next_timer_interrupt() did not check hrtimer
tree for next event.
Function next_timer_interrupt() is needed with dyntick (CONFIG_NO_IDLE_HZ,
VST) implementations, as the system can be in idle when next hrtimer event
was supposed to happen. At least ARM and S390 currently use
next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Mrten Wikstrm
This patch fixes a bug in ixp4xx_set_irq_type() which leads to
GPIO being incorrectly set to both edge triggered for raising
as well as falling edge interrupt types. See the previous
discussion on patch 3312/1.
Signed-off-by: Mrten Wikstrm <marten.wikstrom@passito.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uli Luckas
This is a bugfix.
The comment in arch/arm/common/rtctime.c explains it:
* FIXME: for now, we just copy the alarm time because we're lazy (and
* is therefore buggy - setting a 10am alarm at 8pm will not result in
* the alarm triggering.)
This patch adds one day to the alarm iff the alarm wrapped beyond midnight and therefore appears to be in the past.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds support for the beeper
embedded in the NSLU2 to the machine setup code.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The power button exit routine for the Linksys NSLU2 was not protected by
a machine_is_nslu2(). This patch fixes it.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The initial code did not configure the inbound memory windows for direct
master access to the SDRAM. This patch creates a 1:1 mapping between the
Versatile/PB PCI memory windows and its SDRAM. Note that an updated FPGA
image is needed for Versatile/PB since the original windows were 1MB and
not able to cover the whole SDRAM (now extended to 256MB). The patch also
fixes the PCI IRQ mapping for slot #2.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although you could ask the kernel for panic-on-oops, it remained
non-functional because the architecture specific code fragment had
not been implemented. Add it, so it works as advertised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Commit 99595d0237 forgot to intercept
sys_socketcall as well.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
ARM patch 3226/1 (IXP4xx runtime expansion bus window size configuration)
forgot to update mach-ixp4xx/nslu2-setup.c which leads to the following
compilation error. Update NSLU2 flash support following patch 3226/1.
CC arch/arm/mach-ixp4xx/nslu2-setup.o
arch/arm/mach-ixp4xx/nslu2-setup.c:30: error: NSLU2_FLASH_BASE undeclared here (not in a function)
arch/arm/mach-ixp4xx/nslu2-setup.c:31: error: NSLU2_FLASH_SIZE undeclared here (not in a function)
make[1]: *** [arch/arm/mach-ixp4xx/nslu2-setup.o] Error 1
make: *** [arch/arm/mach-ixp4xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
nslu2-setup.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A change to the SMP initialisation caused the following oops:
CPU1: Booted secondary processor
CPU1: D VIPT write-back cache
CPU1: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU1: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
<7>Calibrating delay loop... 83.14 BogoMIPS (lpj=415744)
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000001c
...
PC is at enqueue_task+0x1c/0x64
LR is at activate_task+0xcc/0xe4
SMP initialisation now requires cpu_possible_map to be initialised in
setup_arch(). Move this from smp_prepare_cpus() to smp_init_cpus()
and call it from our setup_arch() if CONFIG_SMP is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Define the bits for the two board control latches
that control various items on the H1940 iPAQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch adds s3c2400.h, fixing the build for the 2410/2440
platforms.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes the low-level IO init for omap2 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes the low-level IO init for omap1 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Change the IRQ resource range for the ADC device
to be two distinct IRQs
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Because of a type, OSC1 was used for setting the display clock instead of
OSC4. This patch fixes it.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
negative
Patch from Nicolas Pitre
The pre ARMv5 implementation can be aborted if an exception occurs in
the middle of it. Because of that, the ARMv6 implementation doesn't
re-attempt the operation on a failed strex either. Let's make this
transient nature of such a false positive more explicit in the
definition.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The cmpxchg emulation on pre-ARMv5 relies on user code executed from a
kernel address. If the operation cannot complete atomically, it is
aborted from the usr_entry macro by clearing the Z flag. This clearing
of the Z flag is done whenever the user pc is above TASK_SIZE.
However this "pc >= TASK_SIZE" test cannot work in the non MMU case.
Worse: the current code will corrupt the Z flag on every entry to the
kernel.
Let's disable it in the non MMU case for now. Using NPTL on non MMU
targets needs to be worked out anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
struct sockaddr_un loses its padding with EABI. Since the size of the
structure is used as a validation test in unix_mkname(), we need to
change the length argument to 110 whenever it is 112.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Although OABI_COMPAT works fine in most cases, it is still experimental
and could be for ever since it is nearly impossible to handle
everything, e.g. ioctls.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Bring s3c2410 defconfig up to date
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Minor typographical and spelling fixes in Konfig
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
Kconfig | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Add help descriptions to ARCH config items that don't have one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
Kconfig | 32 ++++++++++++++++++++++++++++++--
mach-clps711x/Kconfig | 2 ++
2 files changed, 32 insertions(+), 2 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move to using an enable count for the shared clocks
and protect the clock system using a mutex instead
of just disabling IRQs during the clock update.
Since there is little more code in the path for
non-shared clocks, the enable and disable calls
use the same code for each.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Most ixp2000 boards don't actually work if pci=firmware isn't used, so
the defconfig isn't really the right place to specify this. Instead of
specifying it in the defconfigs, make the relevant board code take care
of setting pci=firmware.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The ixdp2x01_clock is already 50MHz by default, so no need to
override it with 50MHz in the ixdp2801 defconfig as is done now,
which is confusing as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The ixdp2x01 pci init call doesn't check whether it's really running
on an ixdp2x01, making it impossible to compile one kernel that works
on both the ixdp2x01 and another ixp2000 board.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MTD_XIP depends on having working asm/mtd-xip.h; it's not just per-architecture
(arm-only, as current Kconfig would have it), but actually per-subarch as
well. Introduced a new symbol (ARCH_MTD_XIP) set by arch Kconfig; MTD_XIP
depends on it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
