Remove invalid uses of rsvd1 from Beaver device tree. Replace by actual
function names of pinmux option 1.
Taken from https://github.com/NVIDIA/tegra-pinmux-scripts commit
b0aceda108c0 ("remove invalid uses of rsvd1 from beaver config").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This switches a few interrupt definitions that were using either
GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW as IRQ type, which is invalid.
This is mostly a cosmetic change, that doesn't affect any driver.
Analogous to Paul's commit 38333641b6 ("ARM: tegra: nyan: Use proper
IRQ type definitions").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit f8f8f1d044 ("clk: Don't touch hardware when reparenting
during registration") ULPI has been broken on Tegra20 leading to the
following error message during boot:
[ 1.974698] ulpi_phy_power_on: ulpi write failed
[ 1.979384] tegra-ehci c5004000.usb: Failed to power on the phy
[ 1.985434] tegra-ehci: probe of c5004000.usb failed with error -110
Debugging through the changes and finally also consulting the TRM
revealed that rather than the CDEV2 clock off OSC requiring such pin
muxing actually the PLL_P_OUT4 clock is in use. It looks like so far it
just worked by chance of that one having been enabled which Stephen's
commit now changed when reparenting sclk away from pll_p_out4 leaving
that one disabled. Fix this by properly assigning the PLL_P_OUT4 clock
as the ULPI PHY clock.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the missing unit address for the VDE IRAM area node in accordance
with the mmio-sram device tree binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for the Video Decoder Engine found on Tegra30 SoC's.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
IRAM is a static RAM that consists of four contiguous 64 KiB blocks,
it is currently used to store CPU resume code, utilized by the video
decoder engine and could be used as a general-purpose fast memory.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the vf610m4 based boards include the real memory size in their
dts files, so remove the the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the vf500 based boards include the real memory size in their
dts files, so remove the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include memory node unit name in order to fix the following W=1
warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two usb-otg regulators for imx7d-sdb are both called
"regulator-usb-otg1-vbus" and they effectively override each other.
This is most likely a copy-paste error.
Fixes: b877039aa1 ("ARM: dts: imx7d-sdb: Adjust the regulator nodes")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This add a DTS for the Digilent Zybo Z7 board.
This board is the successor board of Zybo, these are almost the same except
for ps-clk-frequency specifications.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu@cybertrust.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, 2x i2c, nor flash, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, i2c, nand uart, spi and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
and sd. But board is not supporting booting from sd card.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is fixing issue reported by dtc:
arch/arm/boot/dts/zynq-microzed.dtb: Warning (unit_address_vs_reg): Node
/memory has a reg or ranges property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prevents the error:
aspeed-smc 1e630000.spi: Error applying setting, reverse things back
The pinmux driver is only capable of modifying selected strapping bits
that make sense to change at runtime. The SPI strapping is not
currently defined modifiable, so "request" the mux as per how the board
is physically strapped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Palmetto BMC has a UART connected to a RS-232 transceiver designed
to be used as a serial console for the host processor. It appears as a
D-sub connector on the back of the chassis.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The NanoPi-M1-Plus have a 8GB eMMC, add a node for it.
This eMMC is always powered with 3.3V.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fixed "mmc2_8bits_pins" label typo; added subject prefixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the I2C clocks so the I2C busses can be used. The clock input is not
device specific (the AO I2C bus uses clk81 as input, while the two I2C
busses in CBUS have a separate "CLKID_I2C" gate, provided by the clock
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
-----BEGIN PGP SIGNATURE-----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=WjCX
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.17" from Krzysztof Kozłowski:
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
* tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: exynos: Fix IOMMU support for GScaler devices on Exynos5250
ARM: dts: exynos: Remove unused bypass-smu property from Xyref5260
ARM: dts: exynos: Add missing interrupts property to PMIC on Trats board
ARM: dts: exynos: Fix unit addresses of PDMA nodes in Exynos5410
ARM: dts: exynos: Fix address of PPMU ACP on Exynos4210
ARM: dts: exynos: Cleanup power domain nodes in exynos3250.dtsi
ARM: dts: exynos: Add touchscreen node to Exynos4412 N710x
ARM: dts: exynos: Add Samsung's Exynos4412-based Midas boards
ARM: dts: exynos: Split Trats2 DTS in preparation for Midas boards
ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
dt-bindings: samsung: Document bindings for Midas family boards
ARM: dts: exynos: Add soc node to exynos4412
ARM: dts: exynos: Add soc node to exynos4210
ARM: dts: exynos: Add soc node to exynos4
ARM: dts: exynos: Add soc node to exynos5440
ARM: dts: exynos: Use pmu label in exynos4412
ARM: dts: exynos: Remove duplicated inclusion of syscon restart nodes on Exynos5410
ARM: dts: exynos: Use label instead of full path in exynos4412-itop-elite
ARM: dts: exynos: Use labels instead of full paths in exynos4412-trats2
ARM: dts: exynos: Use label instead of full path in exynos4412-odroid-common
...
As of commit 7f60830ab1 ("serial: sirf: Use generic
uart-has-rtscts DT property property"), the SiRF UART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "sirf,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=osrs
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.17, round 1" from Alexandre Torgue:
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
* tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: Fix sdio2 rcc hard coded value
dt-bindings: mfd: Add STM32F7 SDMMC2 rcc entry
ARM: dts: stm32: Enable sdio1 for stm32f769-disco
ARM: dts: stm32: Enable sdio1 for stm32f746-eval
ARM: dts: stm32: Enable sdio1 for stm32f746-disco
ARM: dts: stm32: Add sdio pins definition for stm32f7
ARM: dts: stm32: add SPI support on STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32h743i-eval
ARM: dts: stm32: add RTC support on STM32H743
ARM: dts: stm32: enable USB OTG HS on stm32h743i-eval
ARM: dts: stm32: add USB OTG HS and FS support for STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32f769-disco
ARM: dts: stm32: enable USB HS on stm32f769-disco
ARM: dts: stm32: select otg mode for usbotg_hs on stm32746g_eval
ARM: dts: stm32: add gadget fifo sizes to usbotg_hs on stm32f746
ARM: dts: stm32: Add push button to stm32f769 Discovery board
ARM: dts: stm32: Add push button to stm32f469 Discovery board
ARM: dts: stm32: Add leds support to stm32f769 Discovery board
ARM: dts: stm32: Add leds support to stm32f469 Discovery board
ARM: dts: stm32: Fix HSE clock frequency for stm32h743i-disco board
...
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
-----BEGIN PGP SIGNATURE-----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=UfHC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for dra7 sdhci for v4.17" from Tony Lindgren:
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
* tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Correct evm_sd regulator max voltage
ARM: dts: dra76-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: am57xx-idk: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Remove mmc specific pinmux
ARM: dts: am57xx-beagle-x15: Add "vqmmc-supply" property for mmc2
ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes
ARM: dts: dra76-evm: Shift to using common IOdelay data
ARM: dts: dra76x: Create a common file with MMC/SD IOdelay data
ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FCaw
-----END PGP SIGNATURE-----
Merge tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS for 4.17" from Santosh Shilimkar:
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
* tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g: Fix unit-address formatting for serial nodes
dt-bindings: memory: ti-emif: add edac support under emif
ARM: dts: keystone-k2e-clocks: Fix missing unit address separator
ARM: dts: keystone-k2g: Move usb-phy nodes out of soc0
ARM: dts: keystone-k2g: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2g: Move keystone_irq to under device-state-control
ARM: dts: keystone-k2hk: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2l: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2e: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone: Move reset-controller to under device-state-control
ARM: dts: keystone: Move keystone_irq to under device-state-control
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
-----BEGIN PGP SIGNATURE-----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=SDoJ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omap variants for v4.17" from Tony Lindgren:
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
* tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap4-droid4: add soundcard
ARM: dts: motorola-cpcap-mapphone: add audio-codec
ARM: dts: omap3: Add missing #sound-dai-cells
ARM: dts: am43xx: add emif interrupt info
ARM: dts: am33xx: add emif interrupt info
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD SOM-LV
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD torpedo
ARM: dts: am4372: Mark omap_l3_noc with ti,no-idle
ARM: dts: am4372: Mark emif with ti,no-idle
ARM: dts: am33xx: Mark emif with ti,no-idle
ARM: dts: am4372: Add soc node
ARM: dts: am33xx: Add pm-sram phandle to soc node
ARM: dts: am4372: Update emif node
ARM: dts: am33xx: Update emif node
ARM: dts: am4372: Reserve pm code and data regions in ocmcram sram node
ARM: dts: am33xx: Reserve pm code and data regions in ocmcram sram node
ARM: dts: omap: Remove "cooling-{min|max}-level" for CPU nodes
ARM: dts: omap4-droid4: update touchscreen
ARM: dts: am33xx: add PDU001 board
ARM: dts: use 'atmel' as at24 manufacturer in am335x-boneblue
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix all DT dtc warnings when building with W=1
For most of implicated node, the addition of a fake reg property
fixes these warnings.
For others nodes, their location in device tree
have been updated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=raOr
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.17-round1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts update" from Patrice Chotard:
Fix all DT dtc warnings when building with W=1
For most of implicated node, the addition of a fake reg property
fixes these warnings.
For others nodes, their location in device tree
have been updated.
* tag 'sti-dt-for-v4.17-round1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STi: Remove unused clk_ext2f_a9 clock
ARM: dts: STi: Update clocks node location
ARM: dts: STi: Update sound related nodes location
ARM: dts: STi: Add fake reg property for usb2_picophyX nodes
ARM: dts: STi: Add fake reg for restart, powerdown and picophy/softreset
ARM: dts: STi: Add fake reg property for remote processors
ARM: dts: STi: Add fake reg property for irq-syscfg
ARM: dts: STi: Add fake reg property for miphy28lp_phy
ARM: dts: STi: Add fake reg property for sti-display-subsystem
ARM: dts: STi: Move leds node outside soc node
ARM: dts: STi: Fix bindings notation
Add a common device tree for all Nuvoton NPCM750 BMCs and a board
specific device tree for the NPCM750 (Poleg) evaluation board.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Avi Fishman <avifishman70@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove 0x prefix from clkctrl unit address.
This silences the following dtc warning:
Warning (unit_address_format):
Node /clkctrl@0xf8000000 unit name should not have leading "0x"
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There has never been an artpec6 devboard produced
with less than 1 GiB RAM.
Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.
Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
The unit addresses on couple of serial nodes have a leading 0 resulting
in couple of warning messages around simple-bus unit address format
errors when compiled with W=1. Fix the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Commit 95d8b41c76 ("ARM: dts: keystone-k2e-clocks: Add missing unit
name to clock nodes that have regs") fixed the unit names on various
clock nodes but missed out adding the unit address separator on the
clkhyperlink0 clock node. Fix the same.
Fixes: 95d8b41c76 ("ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The two usb-phy nodes are not memory-mapped devices on the
SoC but rather dummy phys for SoCs with transparent autonomous
NOP phys. Move these to outside soc0 to their own node like
done elsewhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 6cbfdd73a9 ("ARM: dts: add sysmmu nodes for exynos5250")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bypass-smu property is neither used nor documented in bindings.
Remove it from Xyref5260 board DTS.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
All the devices on I2C0 support fast mode, so increase the bus speed
to match. The Armada 388 is known to have a timing issue when in
standard mode, which we believe causes the ficticious device at 0x64
to appear.
[gregory.clement@bootlin.com: Note that since the commit fbffee7498
("ARM: dts: Fix I2C repeated start issue on Armada-38x") in 4.14, the
timing issue is managed for the Armada 38x SoCs.]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
dtc now gives the following warning:
arch/arm/boot/dts/rk3288-tinker.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /hdmi@ff980000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dtc now gives the following warning:
arch/arm/boot/dts/kirkwood-t5325.dtb: Warning (sound_dai_property): /sound/simple-audio-card,cpu:sound-dai: property size (4) too small for cell size 1
The binding documentation gives no indication what the cell size should
be (which should be fixed too), so just assume 0 is fine as that is what
the consumer has.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Replace sdio2 rcc hard coded clock value by its macro.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f769-disco board.
broken-cd property is needed as it misses a pullup on board
(resistor R76 is missing).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f746-eval board.
broken-cd property is needed as card detect signal is
connected to a GPIO expander which is not yet supported
in kernel linux.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use the new bindings of the reworked Marvell NAND controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add sound support to Motorola Droid 4 using simple-soundcard
and CPCAP's audio codec. This does not yet correctly represent
the whole audio routing, since McBSP3 is also connected to
Bluetooth and MDM6600 modem (and probably also 4G modem).
These extra DAI links are not yet supported and have not been
tested.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for audio-codec to its DT file.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dtc now gives the following warnings:
arch/arm/boot/dts/omap3-gta04a3.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/omap3-gta04a4.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/omap3-gta04a5.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable HDMI output on all boards which have HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all entries needed for HDMI to function properly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMIF instance on am43xx supports interrupts, so add the info for
completeness sake. Right now, the driver does not use this for anything,
but it is possible it would be used in future.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The EMIF instance on am33xx supports interrupts, so add the info for
completeness sake. Right now, the driver does not use this for anything,
but it is possible it would be used in future.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
libfdt gained a new dependency on strrchr, so copy the implementation
from lib/string.c.
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pass the memory unit-address to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x13x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
In theses cases an empty memory node is passed, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific to am57xx-idk (and not all dra72/dra74 based boards)
since mmc1_clk line in am57xx-idk is not connected to an external
pullup.
While at that change the order of header files in am571x-idk.dts and
am572x-idk.dts so that the modified pinctrl values in am57xx-idk-common
could take effect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific only to dra71-evm (and not all dra72 based boards) since
mmc1_clk line in dra71-evm is not connected to an external pullup.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correct vpo_sd_1v8_3v3 regulator max voltage to 3.3V
Fixes: 9868bc585ae2 ("ARM: dts: Add support for dra718-evm")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc specific pinmux is selected from dra74x-mmc-iodelay.dtsi, so remove
it in dra7-evm.dts
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SD card interface on DRA76x EVM can support
high speed SD cards. The eMMC onboard can support
upto HS200 mode.
Enable support for these higher speed modes in the
device-tree file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have a device-tree include file with common
MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree
file to using that.
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a common device-tree include file with MMC/SD IOdelay data
for DRA76x SoC.
In the most common case, IOdelay data available in datamanual
can directly be used. This file caters to that common case.
Data is based on DRA76x datamanual, SPRS993A, revised July 2017.
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
4.16, please pull the following:
- Mathieu fixes leading 0x and 0's from bindings and Device Tree source
files, he has done this treewide and most of his changes are already in
4.16
- Stefan provides two changes to the BCM283x DTS files in order to fix
DTC warnings
- Florian fixes the amount of RAM on the BCM958625HR reference board to
properly limit to what is initialized by the bootloader
-----BEGIN PGP SIGNATURE-----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=9RVY
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.16/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree fixes for 4.16" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
4.16, please pull the following:
- Mathieu fixes leading 0x and 0's from bindings and Device Tree source
files, he has done this treewide and most of his changes are already in
4.16
- Stefan provides two changes to the BCM283x DTS files in order to fix
DTC warnings
- Florian fixes the amount of RAM on the BCM958625HR reference board to
properly limit to what is initialized by the bootloader
* tag 'arm-soc/for-4.16/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Move arm-pmu out of soc node
ARM: dts: bcm283x: Fix unit address of local_intc
ARM: dts: NSP: Fix amount of RAM on BCM958625HR
ARM: BCM: dts: Remove leading 0x and 0s from bindings notation
- Fix i.MX GPC driver to remove power domains only when they are
initialized in imx_gpc_probe().
- Fix the broken Engicam i.CoreM6 DualLite/Solo RQS board DT to include
imx6dl.dtsi instead of imx6q.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJalfO8AAoJEFBXWFqHsHzOPk4IALx0Gl07tgaTy2VgZJT2w0ud
ZoyeicSNxfM42auRHjC6QhYpQztw8+k4PCuGmUOutHc2Hbw21EXDxLiSwYgGarBR
3OuYShxBg6IExpUk7TM0kDFU0Z4GcpTjAovloM7yjLxCj88dzS+NIiUwPSl02kTp
iAGxVtTQOYLotJFZLQ+DGH3SuaEvOEzeQZz/v4v2/z1IsJRI5IQ2ILtSFEOYhMwh
vgagvvHopS2jIfLXd47PJJvUQuRjXH00FMvrEmBT2b31HJDU2uKn+y4BtMCJHzJV
cTaCwKcrJcLCH2tv5LVUg86VcbL7qbMGjqKQk4aSuEtMtJkpkD4palNG+y69N9g=
=NKMF
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.16" from Shawn Guo:
- Fix i.MX GPC driver to remove power domains only when they are
initialized in imx_gpc_probe().
- Fix the broken Engicam i.CoreM6 DualLite/Solo RQS board DT to include
imx6dl.dtsi instead of imx6q.dtsi.
* tag 'imx-fixes-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 DualLite/Solo RQS
soc: imx: gpc: de-register power domains only if initialized
The Allwinner A83T is a SoC with two clusters of 4 A7 which have a
different clock and regulator.
Set the CPU regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A83T is an octacore A7 divided in two clusters of 4 A7,
each cluster having its own regulator and clock.
The operating points were found in Allwinner BSP and fex files.
Note that there are a few OPPs that are missing:
1608000000Hz with 920000mV
1800000000Hz with 1000000mV
2016000000Hz with 1080000mV
These OPPs are pretty unstable but it might be due to the SoC quickly
overheating (till the board completely shuts down).
It seems impossible to reach those frequencies with none or passive
cooling, so better leave them out by default.
It's still possible to add those OPPs on a per-board basis though.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[maxime: Reordered the nodes alphabetically]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A83T is a SoC with two clusters of 4 A7, each cluster
having its own regulator and clock.
The regulators are board-specific, thus we need labels for cpu0 and
cpu100 so that we can use references to these nodes from the board
header file.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the i.MX 7Solo/Dual Application Processor Reference
Manual the ECSPI1/2/3, UART1/2/3 and SAI1/2/3 peripherals are
connected through the SPBA bus. Other similar SoCs such as i.MX 6UL
add this bus abstraction. This adds the bus also to the i.MX 7
device tree.
The i.MX SDMA driver uses this abstraction to configure watermark
levels slightly differently, so this might change behavior slightly.
There have no issues been observed before or after the patch.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Keypad Port module. Add it disabled by default since
only some boards use it. Boards which do need to specify
additional properties as documented in the device tree bindings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6UL(L) has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1,
04/2016, Table-2-3 AIPS-2 memory map, p. 166
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable support for ARM Performance Monitoring Units available
on the Cortex-A7 CPU. There is only a single interrupt for the
PMU in both variants of the family, i.MX 7Solo and 7Dual.
Tested with perf on a i.MX 7Dual:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit-adress to fix the following build warnings with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
There are cases where dts passes an empty memory node, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We can never idle the l3_main hwmod so mark the omap_l3_noc node
with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a phandle to point to both the pm-sram-code and pm-sram-data nodes
so that the pm code can locate the sram regions needed to copy low level
PM code.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am335x PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 9273083a15 ("usb: dwc2: Fix TxFIFOn sizes and total TxFIFO
size issues") we could use the OTG mode again.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add BCM43438 (bluetooth) as a serdev slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on patched userspace helpers (hciattach).
In order to keep a debug UART we need to switch to uart1.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PMIC node requires external interrupts for proper operation, but property
defining them was missing. This was probably caused by a limited support
for interrupts from more than one parent, which was not possible to define
when support for this board was added. Fix this by adding
'interrupt-extended' property and properly define interrupt lines for PMIC
node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Typo in unit address of PPMU ACP caused DTC warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dtb:
Warning (simple_bus_reg): Node /soc/ppmu_acp@10ae0000 simple-bus unit address format error, expected "106e0000"
PPMU ACP (under 0x10ae0000 address) is present only in Exynos4210 so
move this node to exynos4210.dtsi with fixing the reg address to proper
one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
The Ethernet switch has an embedded interrupt controller. Interrupts
from the embedded PHYs are part of this interrupt controller.
Explicitly list the MDIO bus the embedded PHYs are on, and wire up the
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch will add the chosen container to point stdout-path to serial2
and set the alias for spi0 to spi1 since the SPI NOR flash exists on SPI1.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now require all at24 users to use the "atmel,<model>" fallback in
device tree for different manufacturers.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a new node for reboot modes on LEGO MINDSTORMS EV3. The EV3's
bootloader looks for a magic number in the ARM local RAM and if found,
it will boot into a special firmware update mode where the flash memory
can be written via USB.
This has been testing working using the command:
# systemctl reboot loader
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a description of the RPi3 GPIO expander that the VC4 firmware controls.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This allows adding devices for which the firmware exposes control interface
via the mailbox. An example of such device is the GPIO expander.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Device nodes in device tree should use generic names, so rename
all existing power domains to "power-domain". To keep readable domain
names in debug logs, use label property, which has been introduce by
commit b13b2330aa ("soc: samsung: pm_domains: Read domain name from
the new label property");
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This adds support for the MMS152 found on N710x boards.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdYgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWwyCACeLElOaIYbFWectAjRvpYhOBMwk4mk/qA+
R5MLVhYRBshyb7KcTG4aBuP/FjrY68BllkxR5ANSF0GZCvvxTGgW3/XCouTRtRjd
YLIMlVKZZPokXEYxN1lqwgJjPx0pHBmDjwWcmU1cJ0gr6z5+/lPwYQW1x43S/yqd
T01vP7TsltG7U5Ai+prQfnWkjcKbPZUEqxDtWIRHqNeudJbcIoiWCOC4H+kYbygN
/w9UvaqGdD97Zs//v3jSxxB9CDdX3EScbPPSLhwFjj5Zckm6GJBRSbO2TWnsPv/H
Ed83duV1eSfIePbRIu2Qk6XrUdFU37GKlNA9SNDE58nphYTW7y2R
=Rdqg
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix wrong dwmmc tuning clocks that may make probing HS cards fail to
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
* tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Fix DWMMC clocks
ARM: dts: rockchip: Remove 1.8 GHz operation point from phycore som
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
-----BEGIN PGP SIGNATURE-----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=cN4I
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.16-rc cycle
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
* tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix checking of no-reset-on-init quirk
ARM: dts: LogicPD SOM-LV: Fix I2C1 pinmux
ARM: dts: LogicPD Torpedo: Fix I2C1 pinmux
ARM: dts: OMAP5: uevm: Fix "debounce-interval" property misspelling
ARM: OMAP1: clock: Fix debugfs_create_*() usage
ARM: OMAP2+: Fix sar_base inititalization for HS omaps
ARM: OMAP3: Fix prm wake interrupt for resume
ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt
ARM: OMAP2+: hwmod_core: enable optional clocks before main clock
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DT node should be named after its functionality and not after the
IP it's defining.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TBS A711 has an AXP813 PMIC and a soldered battery, thus, we enable
the battery power supply subnode in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The X-Powers AXP81X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP81X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On both the ast2400 and ast2500 SoCs, the LPC reset controller is
required to bring the UARTs out of reset without waiting for the LPC
reset to be deasserted.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
"Midas" is the codename for a family of smartphones released by Samsung
Mobile. It includes the Galaxy S3 (GT-I9300/I9305) and the Galaxy
Note 2 (GT-N7100/N7105). The boards largely have the same peripherals:
the main differences are touchscreen, display panel and cellular modem.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Midas boards share a lot with Trats2. Split the common parts
out of Trats2 into a common Midas DTSI and a common "Galaxy S3" DTS.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the display pipeline and HDMI output for the Orange Pi mini
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
These hogs are for parts of the system that need to be in this state,
but do not yet have a driver associated with them but they must be
configured in order to successfully boot the host.
There are also some pinmux hogs, where the default mode of the IP block
is configured.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These describe the front panel LEDs that are present on a Palmetto
chassis, and the checkstop GPIO that comes from the Power8 CPU to
indicate a host error.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The LPC device uses LCLK.
Tested-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This addresses some differences between the G5 and G4 LPC nodes that
make them hard to compare. There is no functional change.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These BMC systems require this device to communicate with the host.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The IPMI BT device part of the LPC interface and is used for
communication with the host processor.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This allows the USB gadget framework to be used on Rock2 Square.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The recovery button is connected to ADC1. This is the same setup as the
Firefly board, but for Rock2 the power supply is connected on the module
and all of the inputs are wired up to the edge connector, so use of the
ADC depends on the carrier board.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the display pipeline and HDMI output
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, same stm32f746-pinctrl driver is used for stm32f746 and
stm32f769 MCU. As pin map is different between those 2 MCUs,
a stm32f769-pinctrl driver has been recently added.
This patch
-allows to use stm32f769-pinctrl driver for stm32f769 boards
-reworks stm32 devicetree files to fit with stm32f746 / stm32f769
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
RK3288 Vyasa has eMMC, add dts node to support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Fixes: 187d7967a5 ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb95 ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BananaPi M3 includes HDMI connector, so add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all bits necessary for HDMI on A83T - mixer1, tcon1,
hdmi, hdmi phy and hdmi pinctrl entries.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 stores some magic flags in a portion of the secure SRAM. The
BROM jumps directly to the software entry point set by the SMP code
if the flags are set. This is required for CPU0 hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The PRCM is a collection of clock controls, reset controls, and various
power switches/gates. Some of these can be independently listed and
supported, while a number of CPU related ones are used in tandem with
CPUCFG for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
CPUCFG is a collection of registers that are mapped to the SoC's signals
from each individual processor core and associated peripherals, such as
resets for processors, L1/L2 cache and other things.
These registers are used for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A80 includes an ARM CCI-400 interconnect to support multi-cluster
CPU caches.
Also add the maximum clock frequency for the CPUs, as listed in the
A80 Optimus Board FEX file.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A20 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e346 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The phyCORE-RK3288 RDK could enable SD3.0 card but need vdd_io_sd to
support the voltage range from 1.8V to 3.3V.
And we have also to add relevant UHS modes to the sdmmc node.
Let's also turn off the vdd_io_sd regulator in suspend state.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The card is powered by the RK818 switch vdd_sd which is supplied
by VCC9 (VDD_3V3_IO).
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is
connected to an external power regulator (SY6280AAC).
With this commit we update the pmic binding properties to support
those features.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc1_pins node with bias-pull-up attribute is already defined in
the sunxi-h3-h5.dtsi file. Thus, we can remove it from here.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinctrl configuration for mmc0 and mmc1 so let's
drop the _a suffix from both of them.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the Droid 4 devicetree to properly describe the reset
GPIO. Also rename the node to touchscreen instead of tsp,
which seems to be commonly used for touchscreens.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PDU001 board from EETS GmbH.
The board is built around the byteENGINE module AM335X from
bytes at work AG which in turn is built around a Sitara SoC
from TI.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds dts support for magnetometer on Nokia N9.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: fix missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti) on
all gpio ports of stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds system config support for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti)
for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4412 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4210 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4 boards should use them
as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos5440 device tree is the only one left, which does not use
"soc" node. Add a "soc" node to exynos5440.dtsi in order to make it
consistent with other exynos DTS.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to use soc node, we need to reference soc child nodes by label
in exynos4412. Define pmu label in exynos4.dtsi. Use it in exynos4412
instead of redefining the node by full path.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos-syscon-restart.dtsi is already included by exynos5.dtsi
(through exynos54xx.dtsi).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Extend camera node by label, not by full path in Exynos
4412 Itop Elite. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and i2c1_isp nodes by labels, not by full path in Exynos
4412 Trats2. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 Odroid
boards. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 DTSI.
This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, fimc, mct and sysram nodes by labels, not by full path in
Exynos 4210 Universal C210 board. This avoids error-prone redefinition
of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and fimc nodes by labels, not by full path in Exynos
4210 Trats board. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, mixer and tmu nodes by labels, not by full path in Exynos
4210 DTSI. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define pinctrl labels in exynos4412.dtsi and use them in
exynos4412-pinctrl.dtsi, as it is done in other Exynos DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #v3.18
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node is referred to as a DAI from the sound node and should
therefore have a #sound-dai-cells property.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The lvds encoder chip was omitted by oversight. Add it.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The nattis currently relies on the cmdline to correctly configure the
MTD partition table, and the one given in the device tree is simply
ignored. Which is fortunate, since the device tree partition table is
bonkers and does not match reality.
So, in order to avoid confusion, fix the device tree partition table
to match what is expected (i.e. what is normally provided on the cmdline).
In particular, the rootfs partition should be mtd6.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The copyright holder for this work is Microchip (formerly Atmel)
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node name should be generic and must not contain the part number.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
