Change all the Zoran (ZR36050/ZR36060) drivers to use i2c_master_send instead
of i2c_transfer when possible. This simplifies the code by a few lines in
each driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop support for the ENCODER_DUMP command in the adv7175 driver. ENCODER_DUMP
was never actually defined as far as I can see, so the code was ifdef'd out,
and I suspect it was never used, not even once, as it includes an obvious
array overrun.
The register values of this specific chip can be dumped in a generic way using
the i2c-dev driver and the "i2cdump" user-space tool if it is ever really
needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drop the adv7175 register cache, as it is only written to and never read back
from. This saves 128 bytes of memory and slightly speeds up the register
writes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a (probably harmless) array overrun in the DECODER_DUMP command of the
saa7110 driver. No big deal as this command is not used anywhere anyway.
Also reformat the dump so that it displays nicely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The bt856 driver has a register cache much larger than needed. We really only
write to 3 registers, so a 32-byte cache is a bit too much. We can be just as
efficient with a 6-byte cache. We could even do with a 3-byte cache, but at
the cost of additional arithmetics arguably not worth the spared 3 bytes.
Also, 4 of the 6 other members of the bt856 data structure were not used
anywhere, so we can as well drop them for an additional 16 bytes of memory
spared.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When grabbing composite video with Iomega Buz, the stock driver will
prevent grabbing from the same input twice in a row, forcing the user to
switch inputs before anything useful can be grabbed again. It is caused by
some optimization code in the input selection parts, and triggered by the
saa7111_command() executing cmd 0. The attached patch will remedy this by
disabling cmd 0 altogether; a fix that has no found negative effects on the
rest of the code. In fact, saa7110.c does the exact same thing.
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanups to the zr36057 initialization:
* Drop intermediate local variables.
* Single error path.
Also drop a needless cast on kfree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
All callers of macio_register_driver() either ignore the return value or
return it as the return value of a module_init() function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/macintosh/via-pmu.c:164: warning: `sleep_in_progress' defined but not used
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the use of i2c headers in macintosh drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now powerpc uses the generic RTC stuff we should not enable the old RTC.
Doing so will result in hangs at boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerbook_sleep_grackle is only called inside via-pmu, from pmu_ioctl()
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 49 ++++---------------------------------------------
qeth_proc.c | 18 +++++++++---------
qeth_sys.c | 2 +-
3 files changed, 14 insertions(+), 55 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Bump driver version and reldate.
[TG3]: Skip phy power down on some devices
[TG3]: Fix SRAM access during tg3_init_one()
[X25]: dte facilities 32 64 ioctl conversion
[X25]: allow ITU-T DTE facilities for x25
[X25]: fix kernel error message 64 bit kernel
[X25]: ioctl conversion 32 bit user to 64 bit kernel
[NET]: socket timestamp 32 bit handler for 64 bit kernel
[NET]: allow 32 bit socket ioctl in 64 bit kernel
[BLUETOOTH]: Return negative error constant
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace. This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.
Move over to the preferred way, that is, using compound pages instead. This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away, define
dcdbas_driver and implement ->probe() and ->remove() functions so manual
binding and unbinding will work with this driver.
Also switch to using attribute_group when creating sysfs attributes and
make sure to check and handle errors; explicitely remove attributes when
detaching driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mv64x600_wdt: convert to the new platform device interface Do not use
platform_device_register_simple() as it is going away.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch does the following for v441xx seris drivers:
- stop using platform_device_register_simple() as it is going away
- mark ->probe() and ->remove() methods as __devinit and __devexit
respectively
- initialize "owner" field in driver structure so there is a link
from /sys/modules to the driver
- mark *_init() and *_exit() functions as __init and __exit
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
