The new FT232RL allows setting and getting the value of the latency
timer, like on the FT232BM. However, the driver will not create the
sysfs entries for the RL without this one-line patch.
I have tested it on two systems with successful results.
From: Stepan Moskovchenko <stevenm86@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro. It makes the
code look cleaner, and it's easier to turn the debugging on or off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as908) adds central protection in usbcore for the
prototypical race between opening and unregistering a char device.
The spinlock used to protect the minor-numbers array is replaced with
an rwsem, which can remain locked across a call to a driver's open()
method. This guarantees that open() and deregister() will be mutually
exclusive.
The private locks currently used in several individual drivers for
this purpose are no longer necessary, and the patch removes them. The
following USB drivers are affected: usblcd, idmouse, auerswald,
legousbtower, sisusbvga/sisusb, ldusb, adutux, iowarrior, and
usb-skeleton.
As a side effect of this change, usb_deregister_dev() must not be
called while holding a lock that is acquired by open(). Unfortunately
a number of drivers do this, but luckily the solution is simple: call
usb_deregister_dev() before acquiring the lock.
In addition to these changes (and their consequent code
simplifications), the patch fixes a use-after-free bug in adutux and a
race between open() and release() in iowarrior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, found it. The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.
The system works fine now with CONFIG_USB_SUSPEND=y in the .config.
Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control. Implement HUPCL. Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Mike Swift <mikes@digi.com>
Signed-off-by: Jeremy McBane <jmcbane@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as898) changes the port reset code in the hub driver. If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).
It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility. A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a class which allows for an easier integration with udev.
This code was originally written by Paolo Abeni, and arrived to my tree
as a part of big patch to add binary API on December 18. As I understand,
Paolo always meant the class to be a part of the whole thing. This is his
udev rule to go along with the patch:
KERNEL=="usbmon[0-9]*", NAME="usbmon%n", MODE="0440",OWNER="root",GROUP="bin"
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Last week I've been searching for a driver for the CA-42 cable (see usb
below) that fitted my kernel 2.6.20. I only found an abandoned version for a
driver on your website that indeed worked on 2.6.18 but wouldn't even
compile with a more recent 2.6.20 kernel.
I fiddled 2 evenings with the kernel code and have patched it up now to work
with the modifications in the 2.6.20 kernel. The patch is attached hereafter
and it works fine (at least for me :-) ).
Bus 2 Device 13: ID 0ea0:6858 Ours Technology, Inc.
I had to fiddle a little with the settings in .gnokiirc but that also
occurred with the older 2.6.18 kernel. Nevertheless, on one system with this
cable and my Nokia 6070 I had best results with :
model = 6510
connection = dku5
while on an other system with the same kernel, cable and phone it only worked
with :
model = AT
connection = serial
serial_write_usleep = 1
From: Kees Lemmens <C.W.J.Lemmens@ewi.tudelft.nl>
Cc: <pawel.kot@gmail.com>
Cc: <bozo@andrews.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as893c) improves the method used by the hub driver
to release its private data structure. The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed. The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state. This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection. For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically. For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.
Their old locations were not fully correct. For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:
echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind
to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub. Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.
The patch also makes a very slight change in the way devices with no
driver are handled during suspend. Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called. In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events. Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state. The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea. In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that accesses NULL pointer
when disconnected a cable while play music with usb-speaker.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that used SA_* flags.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to submit Renesas M66592 udc driver.
The M66592 is Renesas USB 2.0 peripheral controller.
This controller supports USB high-speed.
The driver has been tested Gadget Zero, Ethernet Gadget,
File-backed Storage Gadget, and passed usbtest script.
Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Keyspan adapters: USA-49WG and USA-28XG
Signed-off-by: Lucy P. McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes the format of unknown status values to be less verbose and
uses an array instead of several different snprintf calls. Since only
enum values are assigned to it, poll_state is changed from int to enum.
Use abs() for dB values instead of two almost identical return lines.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.
The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32. All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction". (This is the same approach used with OHCI.)
David fixed:
Whitespace fixes; refresh against ehci cpufreq patch; move glue
for that PPC driver to the patch adding it; fix free symbol
capture bugs in modified "constant" macros; and make "hc32" etc
be "le32" unless we really need the BE options, so "sparse" can
do some real good.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI controllers that don't cache enough microframes can get MMF errors
when CPU frequency changes occur between the start and completion of
split interrupt transactions, due to delays in reading main memory
(caused by CPU cache snoop delays).
This patch adds a cpufreq notifier to the EHCI driver that will
inactivate split interrupt transactions during frequency transitions.
It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI
controllers.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements generic support for suspend/resume for usb serial.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
The prev_state member of struct dev_pm_info (defined in include/linux/pm.h) is
only used during a resume to check if the device's state before the suspend was
'off', in which case the device is not resumed. However, in such cases the
decision whether or not to resume the device should be made on the driver level
and the resume callbacks from the device's bus and class should be executed
anyway (the may be needed for some things other than just powering on the
device).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.
- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 7d12e780e0 David Howells performed
this evolution:
"IRQ: Maintain regs pointer globally rather than passing to IRQ handlers"
He correctly updated many of the function definitions that were using this
extra regs pointer parameter but forgot to update some caller sites of
those functions. The reason the modifications was not properly done on all
drivers is that some drivers were rarely compiled because they are for
AMIGA, or that some code sites were inside #ifdefs where the option is not
set or inside #if 0.
Here is the semantic patch that found the occurences
and fixed the problem.
@ rule1 @
identifier fn;
identifier irq, dev_id;
typedef irqreturn_t;
@@
static irqreturn_t fn(int irq, void *dev_id)
{
...
}
@@
identifier rule1.fn;
expression E1, E2, E3;
@@
fn(E1, E2
- ,E3
)
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported by Grzegorz Chimosz <gchimi@gmail.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_unlink_urb() is asynchronous, therefore an URB's buffer may not
be freed without waiting for the completion handler. This patch switches
to usb_kill_urb(), which is synchronous.
Thanks to Alan for making me look at the remaining users of usb_unlink_urb()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usblcd currently has no way to limit memory consumption by fast writers.
This is a security problem, as it allows users with write access to this
device to drive the system into oom despite resource limits.
Here's the fix taken from the modern skeleton driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a classical memory leak in the ioctl handler. The buffer is simply
never freed. This fixes it the obvious way.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you are submitting an URB with GFP_KERNEL holding a spinlock.
In this case the spinlock can be dropped earlier.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New changes in the signal-handling code require compensating changes
in g_file_storage. This patch (as913) by Oleg Nesterov makes the
code use allow_signal() instead of sigprocmask().
From: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as901) fixes an oversight in ohci-hcd. The
hub_status_data routine must not try to access the controller's
memory-mapped registers if the controller is in a low-power state;
such attempts will cause a crash on some architectures (such as PPC).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as904) adds code to check for endpoint descriptor bInterval
values outside the legal limits. Illegal values are set to 32 ms, which
seems like a reasonable default.
This fixes Bugzilla #8432.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysfs adsl_status attribute ignores (aside from returning -EIO to the
user) any error sending a START/STOP command to the device and there is at
least one firmware which never sends a response but appears to work
regardless. Therefore atm_start should also continue if an error is received
so that such firmware is usable.
The official Conexant driver doesn't expect a reply either but this is for
another device (E2 router) and a commonly used firmware does respond.
Also, there is no point in changing -ECONNRESET to -ETIMEDOUT since nothing
ever checks for either of these values.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since usbatm doesn't set the usb_interface driver data until after calling
bind and heavy_init, it would be NULL when the sysfs attributes are read.
Reading the MAC address from atm_dev before atm_dev exists would have been
be possible too.
Calling create_device_file in atm_start will avoid this problem, and the
data is useless until the first status poll runs. However, it must be
ready before a status poll does a printk on line status change otherwise
userspace could react before the files exist.
For completeness I've moved remove_device_file to atm_stop so it's not
called in unbind when it's not needed. There's no point starting ADSL if
atm_start could still fail either.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UNUSUAL_DEV: Sync up some reported devices from Ubuntu
Various unusual dev entries accumulated from Ubuntu bug reports.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
It turns out that le16_to_cpup() and le32_to_cpup() aren't always safe
to call with pointers into packed structures, since those are inlined
functions and GCC may lose the "packed" attribute. So those references
can become unaligned kernel accesses, which are evil on some hardware.
This patch updates uses of those routines in the gadget stack. The
references into packed structures can just use leXX_to_cpu(*x), which
in most cases is more natural. Some other uses in RNDIS, mostly in
debug code, were wrong in the first place; those use get_unaligned().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as912) replaces a couple of calls to flush_workqueue()
with cancel_sync_work() and cancel_rearming_delayed_work(). Using a
more directed approach allows us to avoid some nasty deadlocks. The
prime example occurs when a first-level device (the parent is a root
hub) is removed while at the same time the root hub gets a remote
wakeup request. khubd would try to flush the autosuspend workqueue
while holding the root-hub's lock, and the remote-wakeup workqueue
routine would be waiting to lock the root hub.
The patch also reorganizes the power management portion of
usb_disconnect(), separating it out into its own routine. The
autosuspend workqueue entry is cancelled immediately instead of
waiting for the device's release routine. In addition,
synchronization with the autosuspend thread is carried out even for
root hubs (an oversight in the original code).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=7482.
It sets USB snooping on 4G space for PowerPC platforms without
CONFIG_NOT_COHERENT_CACHE defined.
Reported-by: Stefan Meyer <reyems@telkomsa.net>
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.
The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:
http://openocd.berlios.de/web/http://www.olimex.com/dev/arm-usb-ocd.html
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the newly released Aircard 595U EVDO
modem to the Sierra Wireless driver (sierra.c) in kernel 2.6.21.
I suspect that my mailer may be mangling patches so let me know and
I'll try to resend it.
From: Danny Budik <dbudik@ist-traffic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem reported with consecutive reads in the ldusb
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as910) fixes a ratelimit modification so that the
original error-handling path will be followed even when the log-rate
limitation kicks in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as906) improves the error handling for the USB power/level
attribute file. If an error occurs, the original power-level settings
will be restored.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as881b) makes the ksuspend_usb_wq workqueue freezable. We
don't want a rogue workqueue thread running around, unexpectedly
suspending or resuming USB devices in the middle of a system sleep
transition.
This fixes Bugzilla #8498.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bug in an OHCI quirk handler for Portege 4000; the
Subvendor is 0x1179 (PCI_VENDOR_ID_TOSHIBA)
not 0x102f (PCI_VENDOR_ID_TOSHIBA_2)
bugid 8510
00:02.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device [1179:0004]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like the error path had a copy-paste error. The normal exit path
uses correct URB already.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix debug output. Previously, it would output "0xFFFFFFB0" on 32-bit
archs (and probably "0xFFFFFFFFFFFFFFB0" on 64-bits), because buf is
taken as signed char, which is promoted to signed int, while %x always
expects an unsigned int.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Also, do not access input_dev->private directly, use helpers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as907) prevents us from trying to allocate 0 bytes
when an interface has no endpoint descriptors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as905) removes a micro-optimization from the hub port
initialization code. Previously we had been using a short timeout on
the first attempt the read the device descriptor; now we will use the
standard timeout length.
It's not clear that the short timeout ever provided any benefit. And
now we know of one case where it actually hurts: The device can't meet
the short timeout and then it gets terminally confused.
This fixes Bugzilla #8444.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I haven't personally run across an oops because of this, but I feel safer
with this fix in place.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If this down_interruptible() does fail due to signal_pending() then the state
of the driver will get trashed in interesting ways, because userspace cannot
and will not retry the close().
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change PORT_WIDTH bit for UMTI_WIDE mode and fix a compile warning
introduced in last revision.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as902) fixes a mistake I introduced into usb_bulk_msg().
usb_fill_int_urb() already does the bit-shifting calculation for
high-speed Interrupt intervals; it shouldn't be done twice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Hello,
I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.
The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.
From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as883) removes an out-of-date WARN_ON from the main HCD
endpoint-disable routine. The warning is triggered whenever an
endpoint is disabled while the root hub is suspended. In the past
that may not have been legal, but it definitely is legal now. Merely
unbinding a USB driver will do it.
Furthermore, I've never seen any occurrences of this warning that
really did signal an actual bug or error condition. At this point it
has outlived its purpose.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch (as879) ties up some loose ends from an earlier patch.
These are things I didn't think to include at the time but which
clearly belonged there.
If an autosuspend fails because driver activity races with
the autosuspend call, restart the autosuspend timer.
When a device is resumed by an external request, it counts
as device activity and should update the last_busy time so
that the next autoresume won't occur immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as882) fixes a problem with the EHCI BIOS handoff. On my
machine, the BIOS configures the controller and the handoff fails,
leaving the controller configured. During resume-from-disk, this
confuses ehci-hcd into thinking that the controller has not been
tampered with.
The problem is fixed by turning off the Configured Flag whenever a
BIOS handoff is attempted, whether it succeeds or not.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial fix for bogosity in the ftdi-elan and u132-hcd drivers ... these
have no business including with the internals of other drivers, much less
doing so in a broken way!!
A previous patch resolved one build fix, this resolves another...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Sitecom WL-117 is another "driverless" ZD1211 device where the virtual
windows driver CD must be ejected before the WLAN device appears.
zd1211rw takes care of the ejecting, but usb-storage must be told not to claim
the device.
From: Matthew Davidson <mj.davidson@gmail.com>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the transfer of allocating the descriptor in attach and no longer in open
was incomplete resulting in a memory leak coverity spotted. This fix
is against the patch set you posted.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
sound: convert "sound" subdirectory to UTF-8
MAINTAINERS: Add cxacru website/mailing list
include files: convert "include" subdirectory to UTF-8
general: convert "kernel" subdirectory to UTF-8
documentation: convert the Documentation directory to UTF-8
Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
remove broken URLs from net drivers' output
Magic number prefix consistency change to Documentation/magic-number.txt
trivial: s/i_sem /i_mutex/
fix file specification in comments
drivers/base/platform.c: fix small typo in doc
misc doc and kconfig typos
Remove obsolete fat_cvf help text
Fix occurrences of "the the "
Fix minor typoes in kernel/module.c
Kconfig: Remove reference to external mqueue library
Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
Correct comments in genrtc.c to refer to correct /proc file.
Fix more "deprecated" spellos.
Fix "deprecated" typoes.
...
Fix trivial comment conflict in kernel/relay.c.
Fix the misspellings of "propogate", "writting" and (oh, the shame
:-) "kenrel" in the source tree.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: move USB miscellaneous devices under drivers/input/misc
Input: move USB mice under drivers/input/mouse
Input: move USB gamepads under drivers/input/joystick
Input: move USB touchscreens under drivers/input/touchscreen
Input: move USB tablets under drivers/input/tablet
Input: i8042 - fix AUX port detection with some chips
Input: aaed2000_kbd - convert to use polldev library
Input: drivers/usb/input - usb_buffer_free() cleanup
Input: synaptics - don't complain about failed resets
Input: pull input.h into uinpit.h
Input: drivers/usb/input - fix sparse warnings (signedness)
Input: evdev - fix some sparse warnings (signedness, shadowing)
Input: drivers/joystick - fix various sparse warnings
Input: force feedback - make sure effect is present before playing
drivers/usb/misc/sisusbvga/sisusb_con.c:1436: warning: initialization from incompatible pointer type
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This will allow concentrating all input devices in one place
in {menu|x|q}config.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
As seen on powerpc-cell et al:
CC [M] drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:941:
drivers/usb/host/ehci-ps3.c:79: error: conflicting types for 'dev_dbg'
include/linux/device.h:576: error: previous definition of 'dev_dbg' was here
make[4]: *** [drivers/usb/host/ehci-hcd.o] Error 1
CC [M] drivers/usb/host/ohci-hcd.o
In file included from drivers/usb/host/ohci-hcd.c:921:
drivers/usb/host/ohci-ps3.c:83: error: conflicting types for 'dev_dbg'
include/linux/device.h:576: error: previous definition of 'dev_dbg' was here
dev_dbg() will check format string for you in dummy case also, so remove
buggers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
Input: gpio_keys - add support for switches (EV_SW)
Input: cobalt_btns - convert to use polldev library
Input: add skeleton for simple polled devices
Input: update some documentation
Input: wistron - fix typo in keymap for Acer TM610
Input: add input_set_capability() helper
Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
Input: i8042 - add Panasonic CF-29 to nomux list
Input: lifebook - split into 2 devices
Input: lifebook - add signature of Panasonic CF-29
Input: lifebook - activate 6-byte protocol on select models
Input: lifebook - work properly on Panasonic CF-18
Input: cobalt buttons - separate device and driver registration
Input: ati_remote - make button repeat sensitivity configurable
Input: pxa27x - do not use deprecated SA_INTERRUPT flag
Input: ucb1400 - make delays configurable
Input: misc devices - switch to using input_dev->dev.parent
Input: joysticks - switch to using input_dev->dev.parent
Input: touchscreens - switch to using input_dev->dev.parent
Input: mice - switch to using input_dev->dev.parent
...
Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
USB HID: don't warn on idVendor == 0
USB HID: add 'quirks' module parameter
USB HID: add support for dynamically-created quirks
USB HID: clarify static quirk handling as squirks
USB HID: encapsulate quirk handling into hid-quirks.c
USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
HID: update copyright and authorship macro
HID: introduce proper zeroing of unused bits in output reports
USB HID: add support for WiseGroup MP-8800 Quad Joypad
USB HID: add FF support for Logitech Force 3D Pro Joystick
USB HID: numlock quirk for dell W7658 keyboard
USB HID: Logitech MX3000 keyboard needs report descriptor quirk
USB HID: extend quirk for Logitech S510 keyboard
USB HID: usbkbd/usbmouse - handle errors when registering devices
USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
HID: enable dead keys on a belkin wireless keyboard
USB HID: Thustmaster firestorm dual power v1 support
USB HID: specify explicit size for hid_blacklist.quirks
USB HID: fix retry & reset logic
USB HID: consolidate vendor/product ids
...
Simplify pegasus carrier detection; rely only on the periodic MII
polling. Reverts pieces of c43c49bd61.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update gadget_chip.c, ether.c for newly added Freescale Highspeed USB
device driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freescale high-speed USB SOC can be found on some Freescale processors
among different architectures. It supports both host and device functions.
This driver adds its device support for Linux USB Gadget layer.
It is tested on MPC8349 and MPC8313, but should work on other platforms
with minor tweaks. The driver passed USBCV 1.3 compliance tests. Note
that this driver doesn't yet include OTG support.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jiang Bo <tanya.jiang@freescale.com>
Signed-off-by: Bruce Schmid <duck@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch which adds my device to the list.
This patch enables the broken suspend quirk for the PCI OHCI controller
present in the IT8152F/G RISC-to-PCI Companion Chip.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver uses usb_control_msg() for exchanging data with the device.
When the driver lived freeley _outside_ the kernel tree (pre 2.6.21) the
timeouts for these calls where set to 5*HZ for reading, 1HZ for writing.
(These timeouts seemed to work fine for all users of the driver, at
least nobody complained in the last 2 years.
The current code (2.6.21-rc5) removed the 'HZ' from the timeouts and
left the driver with 5 jiffies for reading and 1 jiffy for writing. My
new machine is fast, but not that fast.
The patch also removes a useless debug statement, which was left over
from testing a broken firmware version
From: Eberhard Fahle <e.fahle@wayoda.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Per the Rui Santos and the hardware manufacturers, this actually inhibits
useful parts of the hardware. The correct way to use this hardware is with the
software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers
are also planning on including Linux drivers/material in future revisions.
CC: Rui Santos <rsantos@grupopie.com>
CC: <johann.wilhelm@student.tugraz.at>
CC: <zihan@huawei.com>
CC: <wanganyu1983@huawei.com>
CC: <dingjianjian@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.
I'm told Axis has a new driver, and will be submitting it soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another workaround for the glitch in the network layer, whereby one call
ignores the (otherwise kernel-wide) convention that free() calls should
not oops when passed nulls. This code already handles that API glitch in
most other paths.
From: Erik Hovland <erik@hovland.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as903) adds a "busnum" sysfs attribute for USB devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device has commands to start/stop the ADSL function, so this adds a
sysfs attribute to allow it to be started/stopped/restarted. It also stops
polling the device for status when the ADSL function is disabled.
There are no problems with sending multiple start or stop commands, even
with a fast loop of them the device still works. There is no need to
protect the restart process from further user actions while it's waiting
for 1.5s.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect usb device shutdown and ignore failed urbs. This happens when the
driver is unloaded or the device is unplugged.
I'm not sure what other urb statuses should be ignored, and the warning
message doesn't need to be shown when the module is unloaded or the device
is removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate define of OHCI_QUIRK_ZFMICRO from ftdi-elan.c, its already
defined in drivers/ush/host/ohci.c
Signed-off-by: "S.Caglar Onur" <caglar@pardus.org.tr>
Cc: <tony.olech@elandigitalsystems.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the detection for the BandRich BandLuxe C100/C100S/C120 HSDPA Data
Card. With the vendor and product IDs are set properly, the data card can
be detected and works fine.
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
skb_push function may return a pointer which is not aligned as required
by struct rndis_packet_msg_type. Using attribute trick to fix this bug.
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add checking of driver registration status and release allocated resources
if it failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: "Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new ohci-pci quirk infrastructure to address the problem it was
created to address: a quirk specific to the Portege 4000, in buzilla as
http://bugzilla.kernel.org/show_bug.cgi?id=6723
Also fix a misuse of "__devinit" for the quirk functions. It must not
be used without first ensuring that the references from the quirk tables
are gone, and that the function using those quirk tables is also gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update "usbnet" so that ethtool reports the name of the minidriver in use
(e.g. asix, cdc_ether, dm9601, rndis_host) instead of "usbnet". This is a
better match to how other network drivers work, resolving a minor open issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanups to the rndis_host code, and a tweak that helps talking to
PXA hardware. Mostly from Ole André Vadla Ravnås <oleavr@gmail.com>
- Prevent SET_INTERFACE requests, they give PXA hardware bad indigestion
- For paranoia, null a pointer after freeing its data
- Wrap up ActiveSync oddities for RNDIS_QUERY in one routine
- Use that wrapper when getting the Ethernet address
- Whitespace fixes
Plus add a comment noting the open issues about some RNDIS clients still
needing TBD kinds of browbeating to accept non-jumbogram packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as897) changes the autosuspend timer code to use the
standard types and macros in dealing with jiffies values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the "bus zero" feature to the usbmon. If a user process specifies bus
with number zero, it receives events from all buses. This is useful when
we wish to see initial enumeration when a bus is created, typically after
a modprobe. Until now, an application had to loop until a new bus could
be open, then start capturing on it. This procedure was cumbersome and
could lose initial events. Also, often it's too bothersome to find exactly
to which bus a specific device is attached.
Paolo Albeni provided the original concept implementation. I added the
handling of "bus->monitored" flag and generally fixed it up.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some host controller drivers may need a PIO fallback when a DMA channel
is temporarily unavailable. This patch provides an address that such
drivers can use for PIO in those cases, and nulls that field out when
no such address is available (highmem) which should help usbmon.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver does
- ignore errors during open
- submit a running urb
- use down_interruptible not handling signals
- GFP_KERNEL with a spinlock held
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as877) adds a "last_busy" field to struct usb_device, for
use by the autosuspend framework. Now if an autosuspend call comes at
a time when the device isn't busy but hasn't yet been idle for long
enough, the timer can be set to exactly the desired value. And we
will be ready to handle things like HID drivers, which can't maintain
a useful usage count and must rely on the time-of-last-use to decide
when to autosuspend.
The patch also makes some related minor improvements:
Move the calls to the autosuspend condition-checking routine
into usb_suspend_both(), which is the only place where it
really matters.
If the autosuspend timer is already running, don't stop
and restart it.
Replace immediate returns with gotos so that the optional
debugging ouput won't be bypassed.
If autoresume is disabled but the device is already awake,
don't return an error for an autoresume call.
Don't try to autoresume a device if it isn't suspended.
(Yes, this undercuts the previous change -- so sue me.)
Don't duplicate existing code in the autosuspend work routine.
Fix the kerneldoc in usb_autopm_put_interface(): If an
autoresume call fails, the usage counter is left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
omninet kills all URBs in close. However write() returns as soon as
the URB has been submitted. Killing the last URB means a race that
can lose that date written in the last call to write().
As a fix this is moved to shutdown().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we report errors to the caller. THis patch adds error handling to the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- report errors
- cleanup in error case
- use of endianness macros
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver ignores errors while starting the transmit queue. It will
never be reported stopped as the completion handler won't run
and it will never be started again as it will be considered started.
This patch adds error handling.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver sets intfdata to NULL while it still can be read and happily followed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB ID of the ADS Tech USBX-707 USB IR blaster (that
comes with the ADS Tech PTV-305 grabber card), which has a ftdi232bm
inside hooked up to a pic.
With this it should be fairly straightforward to make at least lirc
receiving work with this device. I will submit a patch to lirc for that
as soon as I have one ready, I'm getting data with minicom with this
patch, but need to figure out some more details such as best/correct
baudrate.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this has the same race as the visor driver. The counter must be incremented
under the lock it is checked under.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- proper endianness macros
- scheduling in interrupt in error case
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com>
o The "real" usb-devices export now a device node which can
populate /dev/bus/usb.
o The usb_device class is optional now and can be disabled in the
kernel config. Major/minor of the "real" devices and class devices
are the same.
o The environment of the usb-device event contains DEVNUM and BUSNUM to
help udev and get rid of the ugly udev rule we need for the class
devices.
o The usb-devices and usb-interfaces share the same bus, so I used
the new "struct device_type" to let these devices identify
themselves. This also removes the current logic of using a magic
platform-pointer.
The name of the device_type is also added to the environment
which makes it easier to distinguish the different kinds of devices
on the same subsystem.
It looks like this:
add@/devices/pci0000:00/0000:00:1d.1/usb2/2-1
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:1d.1/usb2/2-1
SUBSYSTEM=usb
SEQNUM=1533
MAJOR=189
MINOR=131
DEVTYPE=usb_device
PRODUCT=46d/c03e/2000
TYPE=0/0/0
BUSNUM=002
DEVNUM=004
This udev rule works as a replacement for usb_device class devices:
SUBSYSTEM=="usb", ACTION=="add", ENV{DEVTYPE}=="usb_device", \
NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0644"
Updated patch, which needs the device_type patches in Greg's tree.
I also got a bugzilla assigned for this. :)
https://bugzilla.novell.com/show_bug.cgi?id=250659
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as874) adds another piece to the user-visible part of the
USB autosuspend interface. The new power/level sysfs attribute allows
users to force the device on (with autosuspend off), force the device
to sleep (with autoresume off), or return to normal automatic operation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add logical channel support for ATI Remote Wonder II
The ATI Remote Wonder II can be configured with one of 16 unique logical
channels. Allowing up to 16 remotes to be used independently within
range of each other. This change adds functionality to configure the
receiver and filter the input data to respond or exclude remotes
configured with different logical channels.
Signed-off-by: Peter Stokes <linux@dadeos.freeserve.co.uk>
Acked-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the sierra driver does not directly use usb_kill_urb(). It uses a wrapper.
This wrapper means that callbacks which are running are not killed during
close, resubmitting and illicitly pushing data into the tty layer.
The whole purpose of usb_kill_urb() is subverted. The wrapper must be removed.
The same problem as the option driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the option driver does not directly use usb_kill_urb(). It uses a wrapper.
This wrapper means that callbacks which are running are not killed during
close, resubmitting and illicitly pushing data into the tty layer.
The whole purpose of usb_kill_urb() is subverted. The wrapper must be removed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds some WARN_ON()s to various error checks which
are never supposed to fail. Unsettlingly, one of them has shown up in
a user's log! Maybe making the warning more visible and having the
call-stack information available will help pinpoint the source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NULL checks should be before the first dereference.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 19. 2007 10:25 schrieb Adrian Bunk:
> The Coverity checker spotted the following NULL dereference:
And this fixes an oops upon allocation failures.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes:
- breaking DMA rules about buffers
- usage of _global_ variables to save a single device's attributes
- racy access to urb->status
- smp monotonity issue with statistics
- use of one buffer for many simultaneous URBs
- error handling introduced
- several instances of following NULL pointers
- use after free
- unnecessary GFP_ATOMIC
- GFP_KERNEL in interrupt
- various cleanups
- write room granularity issue that bit cdc-acm
- race in shutdown
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
io_edgeport is using a global variable without locking.
This is _the_ classical race condition. This patch switches to atomic_t.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as870) adds a delay to ehci-hcd's bus_resume routine.
Apparently there are controllers and/or BIOSes out there which need
such a delay to get the ports back into their correct state. This
fixes Bugzilla #8190.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as867) adds an entry for the new power/autosuspend
attribute in Documentation/ABI/testing, and it changes the behavior of
the delay value. Now a delay of 0 means to autosuspend as soon as
possible, and negative values will prevent autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as866) adds new entry points for external USB device
suspend and resume requests, as opposed to internally-generated
autosuspend or autoresume. It also changes the existing
remote-wakeup code paths to use the new routines, since remote wakeup
is not the same as autoresume.
As part of the change, it turns out to be necessary to do remote
wakeup of root hubs from a workqueue. We had been using khubd, but it
does autoresume rather than an external resume. Using the
ksuspend_usb_wq workqueue for this purpose seemed a logical choice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver's help text incorrectly claims to support only single port
devices.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver has an interesting way of handling ENOMEM: complain and ignore.
If you decide to live with allocation failures, you must
1. guard against URBs without corresponding buffers
2. complete allocation failures
3. always test entries for NULL before you follow the pointers
This patch does so.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct the offsets of the SI_CTRL, PRI_CTRL registers according to
the Reference Manual errata sheet in order to prevent unwanted
settings regarding burst transactions and priority states.
Signed-off-by: Christian Engelmayer <Christian.Engelmayer@frequentis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as865) fixes a race in the HCD removal code discovered by
Milan Plzik. Arrival of an interrupt after the root hub was
unregistered could cause the root-hub status timer to start up, even
after it was supposed to have been shut down. The problem is fixed by
moving the del_timer_sync() call to after the HCD's stop() method, at
which time IRQ generation should be disabled.
Cc: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the device is polled for status there is a lot of useful status
information available that is ignored. This patch stores the device info
array when the status is polled and adds sysfs files to the usb device to
allow userspace to query it. Since the device updates its status
internally once a second the poll time is changed to this, and
round_jiffies_relative is used to avoid waking the cpu unnecessarily.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is currently no path from the ATM device in /sys to the USB device's
interface that the driver is using; this patch creates a "device" symlink. It
is then possible to get to the cxacru ADSL statistics
(http://lkml.org/lkml/2007/2/23/328):
/sys/class/atm/cxacru0/device $ ls *_rate *_margin *_attenuation
downstream_attenuation downstream_snr_margin upstream_rate
downstream_rate upstream_attenuation upstream_snr_margin
If this link is not appropriate I'd have to create device files in
/sys/class/atm/cxacru0 instead - which seems less appropriate since the ADSL
statistics are for the USB device not ATM (which is running over the ADSL).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as864) moves the work routine for USB autosuspend from one
source file to another. This permits the removal of one whole global
symbol (!) and should smooth the way for more changes in the future.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone changed the code to kthread and used his style instead of mine.
The problem with the block variables is that they provoke shadowing,
which is actually exactly what has happened in my other tree which
has the class patch.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch exports the attributes cdc-acm knows about a device through sysfs.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new text API, codenamed '1u', which captures more URB
fields than old '1t' interface did. Also the '1u' text API is compatible
with the future "bus zero" extension.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch removes usage of BKL from usblcd, which got it from the old
skeleton driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Iet's kill BKL where we can. This is relative to the last patch to the
skeleton driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
compilation of the skeleton driver is currently broken. It doesn't compile.
So while I am it:
- fix typo
- add comments to answer common questions
- actually allow autosuspend in the driver struct
- increase paralellism by restricting code under locks
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the pxa2xx_udc driver fetch its IRQ from platform resources
rather than using compile-time constants, so that it works properly
on IXP4xx systems not just PXA21x/25x/26x.
Other updates:
- Do that using platform_get_irq()
- Switch to platform_driver_probe()
- Handle device_add() errors
- Remove "function" sysfs attribute and its potential errors
- Whitespace cleanups
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I write a patch adding support "SHARP EMONE(S01SH)" device for ipaq.c.
EMONE is a PDA with built-in HSDPA function.
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Duplicate what Zach Brown did for pr_debug in commit
8b2a1fd1b3
[akpm@linux-foundation.org: fix a couple of things which broke]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver core stopped using the rwsem a long time ago, yet the USB
core still grabbed the lock, thinking it protected something. This
patch removes that useless use.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb-devel <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broken by 4a1728a28a which switched the
return semantics of read_mii_word() but didn't fix usage of
read_mii_word() to conform to the new semantics.
Setting carrier to off based on the NO_CARRIER flag is also incorrect as
that flag only triggers on TX failure and therefore isn't correct when
no frames are being transmitted. Since there is already a 2*HZ MII
carrier check going on, defer to that.
Add a TRUST_LINK_STATUS feature flag for adapters where the LINK_STATUS
flag is actually correct, and use that rather than the NO_CARRIER flag.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ati_remote causes repeats after only .23 seconds with my remote and
makes it hard to use comfortably. Make a precise way of setting the
repeat delay time in milliseconds and default it to 500ms. The old
behavior can be had by setting repeat_delay = 0.
Signed-off-by: Karl Pickett <karl.pickett@gmail.com>
Signed-off-by: Vincent Vanackere <vincent.vanackere@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
itmtoch, mtouchusb and touchkitusb have been replaced with
composite usbtouchscreen driver and can be removed now.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ATI Remote Wonder II can be configured with one of 16 unique logical
channels. Allowing up to 16 remotes to be used independently within
range of each other. This change adds functionality to configure the
receiver and filter the input data to respond or exclude remotes
configured with different logical channels.
Signed-off-by: Peter Stokes <linux@dadeos.freeserve.co.uk>
Acked-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
the Nikon D80 camera will not work without an UNUSUAL_DEV entry embodied
in the attached patch (made against 2.6.20.3). Hope you find it helpful,
or if not, pass it along to someone who does.
From: Emil Larsson <emil@swip.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one significant difference between the behavior of root hubs
(as embodied in host controller hardware) and external hubs: When a
remote-wakeup signal is received, an external hub sends an interrupt
message at the _end_ of the resume sequence but a root hub generates
and interrupt at the _beginning_ of the resume sequence. The host
system must poll for the end of the sequence.
When ehci-hcd was converted to interrupt-driven operation instead of
using polling, the remaining need for this particular poll was
overlooked. This patch (as894) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Separate usbhid code into dedicated drivers/hid/usbhid directory as
discussed previously with Greg, so that it eases maintaineance process.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to omap_udc, noted with some recent testing:
- Cope with some SMP-induced braindamage in ARM's dma_{alloc,free}_coherent()
implementation: alloc() can be called with IRQs blocked, but since late
last year that's no longer true for free(). This resolves really NASTY
problems with logspamming via WARN_ON(), indicating N-page leaks.
- Be more correct in handling GET_STATUS request for RECIP_ENDPOINT ... the
previous code only handled RECIP_INTERFACE, this version should be correct
except for (sigh) bulk/interrupt endpoints.
- Provide a better name for the function reporting whether the board has
vbus sensing wired up.
GET_STATUS requests for endpoint status still acts strangely though, at least
given one flakey host doesn't always ack the first DATA packet, then the packet
that gets retransmitted doesn't have data!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves all of the Novatel device ids to the option driver, where
they belong.
Thanks to Novatel for providing a list of all supported devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was testing the berry_charge module with my Blackberry 8700c and had
great success, thanks. Looking at the code for my own learning I noticed
the following cut and paste error... just a nit.
Signed-off-by: Ken L Johnson <ken@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds a device table entry and a new quirk flag to
the usblp driver for the Seiko Epson Receipt printer. This printer
returns Vendor-Specific values for bInterfaceClass and
bInterfaceSubClass, but the bInterfaceProtocol value is valid and it
works with usblp. The new quirks flag tells the driver to ignore the
Class and SubClass values in the interface descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an ID to recognise the Novatel EV620 wireless adapter.
http://www.novatelwireless.com/products/expedite/ev620.html
It looks like a mini PCI-Express adapter. The mPCIE connector includes USB
pins... the card shows up to the system as a USB device, and powers itself
from the PCI bus.
The card I have isn't activated yet, so I can't get a PPP session up yet, but
I have tested basic serial communication successfully in both 2.6.18 and
2.6.20 kernels, once the product ID was added. (the driver changed quite a
bit between the two revs.) In both drivers, it responds to AT commands and
such.
Signed-off-by: Mark Glines <mark@glines.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these devices have a shared interrupt endpoint. For serialcore to pass
an interrupt endpoint to a subdriver, the subdriver must define and
_export_ a fitting callback. The mos7720 driver failed to do so. This led
invariably to an oops upon open. This patch fixes it. The driver is useless
without it. Please try to get this into 2.6.21 and the stable kernels that
have this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual_devs entry for the Motorola RAZR 3vi.
From: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the linux-usb-devel tree adds two more
product ids to the dm9601 driver. These ids were found on
rebadged dm9601 devices in the wild.
Signed-off-by: Jon Dowland <jon@alcopop.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts d9a7ecacac since it
breaks drivers that need to access the ->port[] array in shutdown
(most of them).
Signed-Off: Jim Radford <radford@blackbean.org>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit d2487cb425.
Russell King points out that it's obviously bogus, and I have to agree.
Not only does "irq" not even exist in that scope, but we obviously need
to free the irq that we actually requested, and that's IRQ_USB.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>,
Cc: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs. usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices. proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.
From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the driver struct used with at91_udc to prevent yet another
bogus warning from "modpost".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put all Code Mercenaries (VID 0x07c0) IOWarriors (PIDs 0x1500 to 0x15ff) on
the HID blacklist. The range of PIDs has been reserved for IOWarriors. Only
5 PIDs are really used yet.
Signed-off-by: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dongle shipped with Logitech DiNovo Edge (0x046d/0xc714) behaves in a weird
non-standard way - it contains multiple reports with the same usage, which
results in remapping of GenericDesktop.X and GenericDesktop.Y usages to
GenericDesktop.Z and GenericDesktop.RX respectively, thus rendering the
touchwheel unusable.
The commit 3506897691 solved this
in a way that it didn't remap certain usages. This however breaks
(at least) middle button of Logic3 / SpectraVideo (0x1267/0x0210),
which in contrary requires the remapping.
To make both of the harware work, allow remapping of these usages again,
and introduce a quirk for Logitech DiNovo Edge "touchwheel" instead - we
disable remapping for key, abs and rel events only for this hardware.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes extra keys (F1-F12 in special mode, zooming, rotate, shuffle)
on Logitech S510 keyboard work.
Logitech S510 keyboard sends in report no. 3 keys which are far above the
logical maximum described in descriptor for given report.
This patch introduces a HID quirk for this wireless USB receiver/keyboard
in order to fix the report descriptor before it's being parsed - the logical
maximum and the number of usages is bumped up to 0x104d). The values are in the
"Reserved" area of consumer HUT, so HID_MAX_USAGE had to be changed too.
In addition to proper extracting of the values from report descriptor, proper
HID-input mapping is introduced for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report descriptor should be output when CONFIG_HID_DEBUG is defined.
This also mitigates the need for DEBUG and DEBUG_DATA defines, so let's
remove them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as861) adds sysfs attributes to expose the autosuspend
delay value for each USB device. If the user changes the delay from 0
(no autosuspend) to a positive value, an autosuspend is attempted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as859) makes the default USB autosuspend delay a module
parameter of usbcore. By setting the delay value at boot time, users
will be able to prevent the system from autosuspending devices which
for some reason can't handle it.
The patch also stores the autosuspend delay as a per-device value. A
later patch will allow the user to change the value, tailoring the
delay for each individual device. A delay value of 0 will prevent
autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as858) makes some minor cleanups to sysfs.c in usbcore.
Unnecessary tests are removed and a few temp variables are added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.
Originally written by Oliver, but hacked up a lot by Greg.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I don't think the current code works with multiple iovecs.
The original would just copy the first part of priv->buf
over and over into multiple iovecs.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch proposes to use USB defines (defined in linux/hid.h)
instead of just plain numbers in the USB_INTERFACE_INFO statements.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as856) attempts to improve the performance of uhci-hcd by
removing the asynchronous skeleton Queue Headers. They don't contain
any useful information but the controller has to read through them at
least once every millisecond, incurring a non-zero DMA overhead.
Now all the asynchronous queues are combined, along with the period-1
interrupt queue, into a single list with a single skeleton QH. The
start of the low-speed control, full-speed control, and bulk sublists
is determined by linear search. Since there should rarely be more
than a couple of QHs in the list, the searches should incur a much
smaller total load than keeping the skeleton QHs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as855) adds some convenience macros to uhci-hcd, to help
simplify the code for computing hardware DMA pointers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a driver for the Davicom DM9601 USB 1.1 10/100Mbps
ethernet adaptor using the usbnet framework.
See http://www.davicom.com.tw/eng/products/dm9601.htm for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the JVC-PRX1 port replicator. Additionally cleans up
the tabs on a few of other IDs in the list.
Reported by: Reuben Thomas <rrt@sc3d.org>
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mon_bin_exit() and mon_text_exit() are called from __init code, so don't mark
them as __exit.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds all of the known Option device ids to the driver.
Many thanks to some Option engineers for getting me this list.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have two tables with the same device ids in it.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Per device data such as brightness belongs to the indivdual device
and should therefore be separate from the the backlight operation
function pointers. This patch splits the two types of data and
allows simplifcation of some code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
backlight_device->sem has a very specific use as documented in the
header file. The external users of this are using it for a different
reason, to serialise access to the update_status() method.
backlight users were supposed to implement their own internal
serialisation of update_status() if needed but everyone is doing
things differently and incorrectly. Therefore add a global mutex to
take care of serialisation for everyone, once and for all.
Locking for get_brightness remains optional since most users don't
need it.
Also update the lcd class in a similar way.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Remove uneeded owner field from backlight_properties structure.
Nothing uses it and it is unlikely that it will ever be used. The
backlight class uses other means to ensure that nothing references
unloaded code.
Based on a patch from Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: remove obsolete setup parameters from input drivers
Input: HIL - fix improper call to release_region()
Input: hid-lgff - treat devices as joysticks unless told otherwise
Input: HID - add support for Logitech Formula Force EX
Input: gpio-keys - switch to common GPIO API
Input: do not lock device when showing name, phys and uniq
Input: i8042 - let serio bus suspend ports
Input: psmouse - properly reset mouse on shutdown/suspend
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
The AT91SAM9261 needs to activate an AHB clock (HCK0) to use the USB Host
controller. Previously clock.c would just enable it at startup, but now
all the unused clocks are automatically disabled.
Based on patch from Nicolas Ferre.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another usb id to the cp2101. It seems to work well.
Please apply, thanks.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a runtime codespace shrink: in most cases, platform devices should
put probe() should in the init section, and remove() in the exit section.
And I have no idea why the module init/exit routines were mismarked.
It also moves one function table into read-only data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, I noticed that support for one of the USB host-to-host cables
never got fully merged ... Kconfig wouldn't show it! Fixed.
Also, changed the CDC Subset default to 'y' so that more of these
cables will work out-of-the-box.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up some error handling paths in usbnet device probing;
one of them could cause oopsing, e.g. with some RNDIS devices.
It also removes some extraneous whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Sitecom CN-124 device IDs to ALI M5632 usb host-to-host cable;
device IDs from Francois Barre <francois.barre@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
from: Kevin Lloyd <linux@sierrawireless.com>
This patch removes the Airprime 5220 device (branded as Audiovox) from
the option.c driver. This device is already supported by the sierra.c
driver.
This was based off of the option.c driver found in kernel 2.6.20-git11.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ps3_system_bus_driver_register is PS3 platform specific function.
On other platforms, it triggers WARN_ON in kref_get.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes our GTCO CalComp Interwrite IPanels from the hid-core.c blacklist
because the HID Driver properly handles them.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB devices do have a configuration 0, in contravention of the
USB spec. Normally 0 is supposed to indicate that a device is
unconfigured.
While we can't change what the device is doing, we can change usbcore.
This patch (as852) allows usb_set_configuration() to accept a config
value of -1 as indicating that the device should be unconfigured. The
request actually sent to the device will still contain 0 as the value.
But even if the device does have a configuration 0, dev->actconfig
will be set to NULL and dev->state will be set to USB_STATE_ADDRESS.
Without some sort of special-case handling like this, there is no way
to unconfigure these non-compliant devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A SET_LINE_CODING control request should return a zero length packet
as an ACK to the host, during the status phase of a USB transaction.
The return value of gs_setup_class() is treated as the number of
bytes to write in the status phase of the control request, by
gs_setup(). For this case, the value returned by gs_setup_class should
be zero for SET_LINE_CODING but, right now, appears to be
sizeof(struct usb_cdc_line_coding).
However, if after doing the memcpy of the line coding descriptor we
set the variable "ret" to be zero, we should return the appropiate ZLP
to the host as an ACK in the status phase of the control request.
I've tested this out using Linux as both host and slave and confirmed
that the following small change fixes the spurious return of
sizeof(struct usb_cdc_line_coding)/wLength bytes in the status phase
of a USB_CDC_REQ_SET_LINE_CODING request. It's not a huge bug but, it
is worth fixing.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE.
I bought this mp3 player that takes SD cards here
http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=AS
I can provide the errors in dmesg, if necessary, but this flag was
determined as necessary by doing a quick google on the errors that were
shown in dmesg.
Signed-off-by: Dylan Taft <d13f00l@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the misspelling of "USBNET_MII" to "USB_USBNET_MII".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add CIDC USB device to HID blacklist since it is actually a USB token
and has its own driver.
Signed-off-by: Zheng XiaoJun <zhengxiaojun@hsic.com.cn>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_RTL8150 must select MII to avoid link errors.
Stolen from a patch by Randy Dunlap.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as the skeleton driver was made ready for autosuspend a race condition
was introduced. The reference to get device must be gotten before the
autosuspend counter is upped, as this operation may sleep, dropping BKL.
Dropping BKL means that the pointer to the device may become invalid.
Here's the fix.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes endian issues in asix_tx_fixup() that prevented
AX88772 and AX88178 devices from working on big-endian systems. With
the attached patch, all three chips are reported to work on big endian.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
