This adds a fastpath for the common workloads to the
MAC suspend flushing.
In common workloads the FIFO flush will take between 100 and
200 microseconds. So we want to avoid calling msleep() in the
common case, as it will waste over 800 microseconds + scheduler
overhead.
This fastpath will hit in workloads where only small chunks
of data are transmitted (downloading a file) or when a TX rate bigger
or equal to 24MBit/s is used when transmitting lots of stuff (iperf).
So in the commonly used workloads it will basically always hit.
In case the fastpath is not hit, there's no real performance or latency
disadvantage from that.
And yes, I measured this. So this is not one of these
bad Programmer Likeliness Assumptions that are always wrong. ;)
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not use workqueue for bss_info_changed post association work.
When driver is notified of association the upper layer will be notified
right after that the association is complete. Doing the post association
work in a workqueue introduces a race condition where the upper layer may
want to make use of the association, but it is not yet complete.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change CONFIG_IWLCORE_RFKILL to CONFIG_IWLWIFI_RFKILL to
be more consistent with other config variables.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix byte count table update. Table must be updated for each
fragment
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves security related functions to iwl-sta.c.
Note that iwl4965_mac_update_tkip_key is still in iwl4965-base.c since it
is a mac80211 handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix book keeping of key table in the driver
to be synchronized with uCode
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for HW encryption/decryption in 1X WEP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds HW encryption support in default WEP mode.
When no key mapping key/pairwise key is used. The key is broadcast key
is used as default/global/static key.
This code assumes that group cast key is added after pairwise key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declaration for static WEP host command. This command will
be used for default WEP group keys when no key mapping keys are used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The buffersize allocated is not accurate.
Writing to these buffers with scnprintf is safer.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates handlers to support
iwlwifi init flow for multiple HWs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows creating interfaces in WDS mode or switching
existing ones into WDS mode (both via cfg80211 and wext.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some timings for pre-TBTT and synthetic PU.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we add multiple todo entries, we rely on them being executed
mostly in the right order, especially when a key is being replaced.
But when a default key is replaced, the todo list order will differ
from the order when the key being replaced is not a default key, so
problems will happen. Hence, just move each todo item to the end of
the list when it is added so we can in the other code ensure that
hw accel for a key will be disabled before it is enabled for the
replacement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When STAs are expired, we need to hold the sta_lock. Using
the same lock for keys too would then mean we'd need another
key free function, and that'll just lead to confusion, so just
use a new spinlock for all key lists.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to send BSS changes to driver from beacons processed
during scanning. We are more interested in beacons from an AP with which
we are associated - these will still be used to send updates to driver as
the beacons are received without scanning.
This change·removes the requirement that bss_info_changed needs to be atomic.
The beacons received during scanning are processed from a tasklet, but if we
do not call bss_info_changed for these beacons there is no need for it to be
atomic. This function (bss_info_changed) is called either from workqueue or
ioctl in all other instances.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some command structs contain reserved or unused fields, which the driver
send uninitialized down to the card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (co-developed by Dan Williams and Holger Schurig) uses a kfifo
object for events and a swapping buffer scheme for the command response to
preserve the zero-copy semantics of the CF driver and keep memory usage low.
The main thread should only ever touch the buffer indexed by priv->resp_idx,
while the interface code is free to write to the second buffer, then swap
priv->resp_idx under the driver spinlock. The firmware specs only permit
one in-flight command, so there will only ever be one command response to
process at a time.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few more instances of sta_info_get calls not being
protected by RCU, fix them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2x00lib_intf_scheduled_iter() we use the hw->beacon_update()
callback function. This means that it should behave similarly as mac80211
when that uses the function.
This means that the skb should only be freed when beacon_update() has failed,
otherwise the driver is the owner and is responsible for freeing the buffer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous key locking patch left a small race: it would be possible
to add a key and take the interface down before the key todo is run so
that hwaccel for that key is enabled on an interface that is down. Avoid
this by running the todo list when an interface is brought up or down.
This patch also fixes a small bug: before this change, a few functions
used the key list without the lock that protects it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we fixed the TPS flag assignment in commit
b63009b456
we don't need the workaround for the bcm44xx chip anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This one got renamed, complicating the merge a bit...this should restore
it to its intended state.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change is necessary to allow cwnd to grow during persistent
reordering. Cwnd moderation is applied when in the disorder state
and an ack that fills the hole comes in. If the hole was greater
than 3 packets, but less than tp->reordering, cwnd will shrink when
it should not have.
Signed-off-by: John Heffner <jheffner@napa.(none)>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alloc_netdev_mq() tries to produce 32-bytes alignment for both
the net_device itself and its private data. The second alignment is
achieved by adding the NETDEV_ALIGN_CONST to the whole size of
the memory to be allocated.
However, for those devices that do not need the private area, this
addition just makes the net_device weight 1024 + 32 = 1068 bytes,
i.e. consume twice as much memory.
Since loopback device is such (sizeof_priv == 0 for it), and each
net namespace creates one, this can save a noticeable amount of
memory for kernel with net namespaces turned on.
After this set the lo device is actually allocated from a size-1024
kmem cache on i386 box even with NETPOLL and WIRELESS_EXT turned on.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_set_net is called for
- just allocated devices
- devices moving from one namespace to another
release_net has proper check inside to distinguish these cases.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol control sockets and netlink kernel sockets should not prevent the
namespace stop request. They are initialized and disposed in a special way by
sk_change_net/sk_release_kernel.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make release_net/hold_net noop for performance-hungry people. This is a debug
staff and should be used in the debug mode only.
Add check for net != NULL in hold/release calls. This will be required
later on.
[ Added minor simplifications suggested by Brian Haley. -DaveM ]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
And no need in some IPPROTO_XXX enabling, since ipv6 code
doesn't have any filtering.
So, just set proper net and mark device with NETNS_LOCAL.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the ip_route_output_key(), dev_get_by_...() and ipv6_chk_addr()
calls are now stubbed with init_net.
Fortunately, all the places already have where to get the proper
net from.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move hashes in the struct ip6_tnl_net, replace tnls_xxx[] with
ip6n->tnlx_xxx[] and handle init and exit appropriately.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the code, that reference it already has the ip6_tnl_net pointer,
so s/ip6_fb_tnl_dev/ip6n->fb_tnl_dev/ and move creation/releasing
code into net init/exit ops.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to ip6_tnl_lookup were stubbed with init_net - give them
a proper one.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hashes and fallback device used in them will be per-net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sit-generated traffic enter the namespace.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set proper net and mark a new device as NETNS_LOCAL before registering.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I.e. replace init_net stubs in ip_route_output_key() calls.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just move all the hashes on the sit_net structure and
patch the rest of the code appropriately.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and register one in sit_init_net, use sitn->fb_tunnel_dev
over the code and unregister one in sit_exit_net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace introduced in the previous patch init_net stubs
with the proper net pointer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
... to make them prepared for future hashes and fallback device
move on the struct sit_net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
