Root cause: When kernel crashes, On brocade 815/825 adapters,
bfa IOC state machine and FW doesn't get a notification and
hence are not cleanly shutdown. So registers holding driver/IOC
state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to fail
during kdump kernel boot.
Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Retry FDISC a max of 6 times. Introduce new events to handle vport
login fails due to max logins to fabric/switch.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On Xen kernels, if ATC (address translation cache) is enabled, the
first PCIe DMA read from the adapter fails with an error. This is due to
a bug ASIC, which leads to a failure of 1860 ports to be initialised.
This patch includes the fix to disable Invalidated Tag Match Enable
capability by setting the bit 26 of CHIP_MISC_PRG to 0, by default it is
set to 1.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update addl. fields in FDMI to confirm to FC-GS6 standard for RPA and
RHBA commands.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The WARN_ON condition check in IO completion path is wrong. IOtags
returned by the firmware is compared with driver/bfa iotag after masking
the retry count bits.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
D-Port is a new port type created with the intention of running link
level diagnostic tests like loopback, traffic test. In static D-port
mode, user configures the port to D-port mode and starts the test, but
in dynamic D-port, once the Brocade switch port is configured to
D-port, it will reject the regular FLOGI from HBA with reason that it is
in D-port mode. So based on the reason code HBA port will turn itself into
D-port and start diagnostic test.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes changes to get FC HBA feature Forward Error
Correction (FEC) (enabled at 16Gig speed) status from firmware and to
return to brocade HBA management utility.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes changes to 1) Enable/disable fc credit recovery on
Brocade FC adapter port operating at max supported speed. 2) Get credit
recovery status and stats related to credit loss and recovered credits
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The 'ctl' field of the 'struct ata_taskfile' is not really dual purpose, i.e.
it is not intended for storing the alternate status register (which is mapped
at the same address in the legacy IDE controllers) in the qc_fill_rtf() method.
No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status
register's value in the 'ctl' field of 'qc->result_tf', hence this driver should
not do this as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When enable lockdep, seeing "possible irq lock inversion dependency detected"
error. This patch fixes the issue.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 39c60a0948 '[SCSI] sd: fix array cache flushing bug causing
performance problems' added temp as a pointer to "temporary " and used
sizeof(temp) - 1 as its length. But sizeof(temp) is the size of the
pointer, not the size of the string constant. Change temp to a static
array so that sizeof() does what was intended.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes two cppcheck errors in drivers/scsi/bfa/bfad_im.c
[jejb: correct strlcpy fix]
Signed-off-by: Jakob Normark <jakobnormark@gmail.com>
Acked-by: Vijay Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to differentiate between iMR(no external memory) and MR(with
external memory) controllers.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MegaRAID older Firmware does not support uneven span configuration for PRL11.
E.g User wants to create 34 Driver PRL11 config, it was not possible using old
firmware, since it was not supported configuration in old firmware
Old Firmware expect even number of Drives in each span and same number of
physical drives at each span. Considering above design, 17 Drives at Span-0
and 17 drives at span-1 was not possible.
Now, using this new feature Firmware and Driver both required changes. New
Firmware can allow user to create 16 Drives at span-0 and 18 Drives at
span-1. This will allow user to create 34 Drives Uneven span PRL11.
RAID map is interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives. Since legacy RAID map consider
Even Span design, there was no place to keep Uneven span information in
existing Raid map. Because of this limitation, for Uneven span VD, driver can
not use RAID map.
This patch address the changes required in Driver to support Uneven span PRL11
support.
1. Driver will find if Firmware has UnevenSpanSupport or not by reading
Controller Info.
2. If Firmware has UnvenSpan PRL11 support, then Driver will inform about its
capability of handling UnevenSpan PRL11 to the firmware.
3. Driver will update its copy of span info on each time Raid map update is
called.
4. Follow different IO path if it is Uneven Span. (For Uneven Span, Driver
uses Span Set info to find relavent fields for that particular Virtual
Disk)
More verbose prints will be available by setting "SPAN_DEBUG" to 1 at
compilation time.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This Driver will use more than 8 MSI-x support provided by Invader/Fury max
upto 128 MSI-x.
[jejb: fix checkpatch warning]
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Free event detail memory from more common place, instead of doing it for
limited device types.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do not return SCSI_MLQUEUE_HOST_BUSY, but send DID_ERROR to SCSI mid-layer, if
adapter is in critical error state. "SCSI_MLQUEUE_HOST_BUSY" will keep same
SCSI command in loop and it is not a right return value, if controller is
hardware critical error.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make the driver return appropriate sense data when an unsupported
operation is queued. This will cause the SCSI layer to stop issuing the
offending command.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Not all disks fill out the VPD pages correctly. Add a blacklist flag
that allows us ignore the SBC-3 VPD pages for a given device. The
BLIST_SKIP_VPD_PAGES flag triggers our existing skip_vpd_pages
scsi_device parameter to bypass VPD scanning.
Also blacklist the offending Seagate drive model.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If CONFIG_SCSI_MPT2SAS_LOGGING is undefined, then these warnings are emitted
drivers/scsi/mpt2sas/mpt2sas_scsih.c: In function '_scsih_sas_broadcast_primitive_event'
drivers/scsi/mpt2sas/mpt2sas_scsih.c:5810:40: warning: unused variable 'event_data'
Use pr_info() function instead of dewtprintk().
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Modified device scan routine so each configuration page read breaks from the
while loop when the ioc_status is not equal to MPI2_IOCSTATUS_SUCCESS.
[jejb: checkpatch fixes]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated the mpt2sas driver code that issues hard reset to comply with the
timing requirements mentioned in MPI specifications rev V.
[jejb: checpatch fixes]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
