v5 -> v6 (current):
-removed so far unused static functions
-corrected dev_addr_del_multiple to call del instead of add
v4 -> v5:
-added device address type (suggested by davem)
-removed refcounting (better to have simplier code then safe potentially few
bytes)
v3 -> v4:
-changed kzalloc to kmalloc in __hw_addr_add_ii()
-ASSERT_RTNL() avoided in dev_addr_flush() and dev_addr_init()
v2 -> v3:
-removed unnecessary rcu read locking
-moved dev_addr_flush() calling to ensure no null dereference of dev_addr
v1 -> v2:
-added forgotten ASSERT_RTNL to dev_addr_init and dev_addr_flush
-removed unnecessary rcu_read locking in dev_addr_init
-use compare_ether_addr_64bits instead of compare_ether_addr
-use L1_CACHE_BYTES as size for allocating struct netdev_hw_addr
-use call_rcu instead of rcu_synchronize
-moved is_etherdev_addr into __KERNEL__ ifdef
This patch introduces a new list in struct net_device and brings a set of
functions to handle the work with device address list. The list is a replacement
for the original dev_addr field and because in some situations there is need to
carry several device addresses with the net device. To be backward compatible,
dev_addr is made to point to the first member of the list so original drivers
sees no difference.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong message type that are triggered by
user updates, the following commands:
(term1)# conntrack -I -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state LISTEN
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_SENT
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_RECV
only trigger event message of type NEW, when only the first is NEW
while others should be UPDATE.
(term2)# conntrack -E
[NEW] tcp 6 10 LISTEN src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_SENT src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_RECV src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
This patch also removes IPCT_REFRESH from the bitmask since it is
not of any use.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a problem when you use 32 nodes in the cluster
match:
% iptables -I PREROUTING -t mangle -i eth0 -m cluster \
--cluster-total-nodes 32 --cluster-local-node 32 \
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables: Invalid argument. Run `dmesg' for more information.
% dmesg | tail -1
xt_cluster: this node mask cannot be higher than the total number of nodes
The problem is related to this checking:
if (info->node_mask >= (1 << info->total_nodes)) {
printk(KERN_ERR "xt_cluster: this node mask cannot be "
"higher than the total number of nodes\n");
return false;
}
(1 << 32) is 1. Thus, the checking fails.
BTW, I said this before but I insist: I have only tested the cluster
match with 2 nodes getting ~45% extra performance in an active-active setup.
The maximum limit of 32 nodes is still completely arbitrary. I'd really
appreciate if people that have more nodes in their setups let me know.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
As packets ending with NEXTHDR_NONE don't have a last extension header,
the check for the length needs to be after the check for NEXTHDR_NONE.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Due to a semantic changes in flush_workqueue() the current approach of
synchronizing the sysfs handling for connections doesn't work anymore. The
whole approach is actually fully broken and based on assumptions that are
no longer valid.
With the introduction of Simple Pairing support, the creation of low-level
ACL links got changed. This change invalidates the reason why in the past
two independent work queues have been used for adding/removing sysfs
devices. The adding of the actual sysfs device is now postponed until the
host controller successfully assigns an unique handle to that link. So
the real synchronization happens inside the controller and not the host.
The only left-over problem is that some internals of the sysfs device
handling are not initialized ahead of time. This leaves potential access
to invalid data and can cause various NULL pointer dereferences. To fix
this a new function makes sure that all sysfs details are initialized
when an connection attempt is made. The actual sysfs device is only
registered when the connection has been successfully established. To
avoid a race condition with the registration, the check if a device is
registered has been moved into the removal work.
As an extra protection two flush_work() calls are left in place to
make sure a previous add/del work has been completed first.
Based on a report by Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Roger Quadros <ext-roger.quadros@nokia.com>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
pid doesn't count with some band having more bitrates than the one
associated the first time.
Fix that by counting the maximal available bitrate count and allocate
big enough space.
Secondly, fix touching uninitialized memory which causes panics.
Index sucked from this random memory points to the hell.
The fix is to sort the rates on each band change.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
minstrel doesn't count max rate count in fact, since it doesn't use
a loop variable `i' and hence allocs space only for bitrates found in
the first band.
Fix it by involving the `i' as an index so that it traverses all the
bands now and finds the real max bitrate count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to lock using the cfg80211_mutex in
wiphy_apply_custom_regulatory(). Without the lock
there is possible race between processing a reply from CRDA
and a driver calling wiphy_apply_custom_regulatory(). During
the processing of the reply from CRDA we free last_request and
wiphy_apply_custom_regulatory() eventually accesses an
element from last_request in the through freq_reg_info_regd().
This is very difficult to reproduce (I haven't), it takes us
3 hours and you need to be banging hard, but the race is obvious
by looking at the code.
This should only affect those who use this caller, which currently
is ath5k, ath9k, and ar9170.
EIP: 0060:[<f8ebec50>] EFLAGS: 00210282 CPU: 1
EIP is at freq_reg_info_regd+0x24/0x121 [cfg80211]
EAX: 00000000 EBX: f7ca0060 ECX: f5183d94 EDX: 0024cde0
ESI: f8f56edc EDI: 00000000 EBP: 00000000 ESP: f5183d44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 14617, ti=f5182000 task=f3934d10 task.ti=f5182000)
Stack: c0505300 f7ca0ab4 f5183d94 0024cde0 f8f403a6 f8f63160 f7ca0060 00000000
00000000 f8ebedf8 f5183d90 f8f56edc 00000000 00000004 00000f40 f8f56edc
f7ca0060 f7ca1234 00000000 00000000 00000000 f7ca14f0 f7ca0ab4 f7ca1289
Call Trace:
[<f8ebedf8>] wiphy_apply_custom_regulatory+0x8f/0x122 [cfg80211]
[<f8f3f798>] ath_attach+0x707/0x9e6 [ath9k]
[<f8f45e46>] ath_pci_probe+0x18d/0x29a [ath9k]
[<c023c7ba>] pci_device_probe+0xa3/0xe4
[<c02a860b>] really_probe+0xd7/0x1de
[<c02a87e7>] __driver_attach+0x37/0x55
[<c02a7eed>] bus_for_each_dev+0x31/0x57
[<c02a83bd>] driver_attach+0x16/0x18
[<c02a78e6>] bus_add_driver+0xec/0x21b
[<c02a8959>] driver_register+0x85/0xe2
[<c023c9bb>] __pci_register_driver+0x3c/0x69
[<f8e93043>] ath9k_init+0x43/0x68 [ath9k]
[<c010112b>] _stext+0x3b/0x116
[<c014a872>] sys_init_module+0x8a/0x19e
[<c01049ad>] sysenter_do_call+0x12/0x21
[<ffffe430>] 0xffffe430
=======================
Code: 0f 94 c0 c3 31 c0 c3 55 57 56 53 89 c3 83 ec 14 8b 74 24 2c 89 54 24 0c 89 4c 24 08 85 f6 75
06 8b 35 c8 bb ec f8 a1 cc bb ec f8 <8b> 40 04 83 f8 03 74 3a 48 74 37 8b 43 28 85 c0 74 30 89 c6
8b
EIP: [<f8ebec50>] freq_reg_info_regd+0x24/0x121 [cfg80211] SS:ESP 0068:f5183d44
Cc: stable@kernel.org
Reported-by: Nataraj Sadasivam <Nataraj.Sadasivam@Atheros.com>
Reported-by: Vivek Natarajan <Vivek.Natarajan@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another bug in the "cfg80211: do not replace BSS structs" patch,
a forgotten length update leads to bogus data being stored and
passed to userspace, often truncated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fragmentation threshold is defined to be including the
FCS, and the code that sets the TX_FRAGMENTED flag correctly
accounts for those four bytes. The code that verifies this
doesn't though, which could lead to spurious warnings and
frames being dropped although everything is ok. Correct the
code by accounting for the FCS.
(JWL -- The problem is described here:
http://article.gmane.org/gmane.linux.kernel.wireless.general/32205 )
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net_create() will be used by C/R to create fresh netns on restart.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_net_ns() doesn't copy anything, it creates fresh netns, so
get/put of old netns isn't needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_prequeue() refers to the constant value (TCP_RTO_MIN) regardless of
the actual value might be tuned. The following patches fix this and make
tcp_prequeue get the actual value returns from tcp_rto_min().
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.
The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.
Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based almost entirely upon a patch by Eric Dumazet.
The common case is to have num-tx-queues <= num_rx_queues
and even if num_tx_queues is larger it will not be significantly
larger.
Therefore, a subtraction loop is always going to be faster than
modulus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ba25ff4c6 ("br2684: convert to
net_device_ops") inadvertently deleted the initialization of the net_dev
pointer in the br2684_dev structure, leading to crashes. This patch
adds it back.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.
Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek wrote:
> Since 4fb6699481 ("net: Optimize memory
> usage when splicing from sockets.") I'm seeing this oops (e.g. in
> 2.6.30-rc3) when splicing from a TCP socket to /dev/null on a driver
> (mv643xx_eth) that uses LRO in the skb mode (lro_receive_skb) rather
> than the frag mode:
My patch incorrectly assumed skb->sk was always valid, but for
"frag_listed" skbs we can only use skb->sk of their parent.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Debugged-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- ieee80211_wep_init(), which is called with rtnl_lock held, blocks in
request_module() [waiting for modprobe to load a crypto module].
- modprobe blocks in a call to flush_workqueue(), when it closes a TTY
[presumably when it exits].
- The workqueue item linkwatch_event() blocks on rtnl_lock.
There's no reason for wep_init() to be called with rtnl_lock held, so
just move it outside the critical section.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.
This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bluetooth 2.1 specification introduced four different security modes
that can be mapped using Legacy Pairing and Simple Pairing. With the
usage of Simple Pairing it is required that all connections (except
the ones for SDP) are encrypted. So even the low security requirement
mandates an encrypted connection when using Simple Pairing. When using
Legacy Pairing (for Bluetooth 2.0 devices and older) this is not required
since it causes interoperability issues.
To support this properly the low security requirement translates into
different host controller transactions depending if Simple Pairing is
supported or not. However in case of Simple Pairing the command to
switch on encryption after a successful authentication is not triggered
for the low security mode. This patch fixes this and actually makes
the logic to differentiate between Simple Pairing and Legacy Pairing
a lot simpler.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing
When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.
If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These are later assigned to other values without being used meanwhile.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.25 we added UDP mem accounting.
This unfortunatly added a penalty when a frame is transmitted, since
we have at TX completion time to call sock_wfree() to perform necessary
memory accounting. This calls sock_def_write_space() and utimately
scheduler if any thread is waiting on the socket.
Thread(s) waiting for an incoming frame was scheduled, then had to sleep
again as event was meaningless.
(All threads waiting on a socket are using same sk_sleep anchor)
This adds lot of extra wakeups and increases latencies, as noted
by Christoph Lameter, and slows down softirq handler.
Reference : http://marc.info/?l=linux-netdev&m=124060437012283&w=2
Fortunatly, Davide Libenzi recently added concept of keyed wakeups
into kernel, and particularly for sockets (see commit
37e5540b3c
epoll keyed wakeups: make sockets use keyed wakeups)
Davide goal was to optimize epoll, but this new wakeup infrastructure
can help non epoll users as well, if they care to setup an appropriate
handler.
This patch introduces new DEFINE_WAIT_FUNC() helper and uses it
in wait_for_packet(), so that only relevant event can wakeup a thread
blocked in this function.
Trace of function calls from bnx2 TX completion bnx2_poll_work() is :
__kfree_skb()
skb_release_head_state()
sock_wfree()
sock_def_write_space()
__wake_up_sync_key()
__wake_up_common()
receiver_wake_function() : Stops here since thread is waiting for an INPUT
Reported-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is the sctp code to enable hardware crc32c offload for
adapters that support it.
Originally by: Vlad Yasevich <vladislav.yasevich@hp.com>
modified by Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a brand new GRO skb, we cannot call ip_hdr since the header
may lie in the non-linear area. This patch adds the helper
skb_gro_network_header to handle this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_gro_* code fails to handle the case where a header starts
in the linear area but ends in the frags area. Since the goal
of skb_gro_* is to optimise the case of completely non-linear
packets, we can simply bail out if we have anything in the linear
area.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now we have no upper limit on the size of the route cache hash table.
On a 128GB POWER6 box it ends up as 32MB:
IP route cache hash table entries: 4194304 (order: 9, 33554432 bytes)
It would be nice to cap this for memory consumption reasons, but a massive
hashtable also causes a significant spike when measuring OS jitter.
With a 32MB hashtable and 4 million entries, rt_worker_func is taking
5 ms to complete. On another system with more memory it's taking 14 ms.
Even though rt_worker_func does call cond_sched() to limit its impact,
in an HPC environment we want to keep all sources of OS jitter to a minimum.
With the patch applied we limit the number of entries to 512k which
can still be overriden by using the rt_entries boot option:
IP route cache hash table entries: 524288 (order: 6, 4194304 bytes)
With this patch rt_worker_func now takes 0.460 ms on the same system.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I initially implemented this protocol, I disregarded the use of netlink
attribute headers, thinking for my purposes they weren't needed. I've come to
find out that, as I'm starting to work with sending down messages with
associated data (like config messages), the kernel code spits out warnings about
trailing data in a netlink skb that doesn't have an associated header on it. As
such, I'm going to start including attribute headers in my netlink transaction,
and so for completeness, I should likely include them on messages bound from the
kernel to user space. This patch adds that header to the kernel, and bumps the
protocol version accordingly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kernel inserts a temporary SA for IKE, it uses the wrong hash
value for dst list. Two hash values were calcultated before: one with
source address and one with a wildcard source address.
Bug hinted by Junwei Zhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP MIB (RFC 4293) defines stats for InOctets, OutOctets, InMcastOctets and
OutMcastOctets:
http://tools.ietf.org/html/rfc4293
But it seems we don't track those in any way that easy to separate from other
protocols. This patch adds those missing counters to the stats file. Tested
successfully by me
With help from Eric Dumazet.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VLAN event handler does not adjust the VLAN
device's carrier state when the real device or the VLAN device is set
administratively up or down.
The following patch adds a transfer of operating state from the
real device to the VLAN device when the real device is administratively
set up or down, and sets the carrier state up or down during init, open
and close of the VLAN device.
This permits observers above the VLAN device that care about the
carrier state (bonding's link monitor, for example) to receive updates
for administrative changes by more closely mimicing the behavior of real
devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Related-to: commit 325fb5b4d2
The compat path suffers from a similar problem. It only uses a __be32
when all of the recent code uses, and expects, an nf_inet_addr
everywhere. As a result, addresses stored by xt_recents were
filled with whatever other stuff was on the stack following the be32.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
With a minor compile fix from Roman.
Reported-and-tested-by: Roman Hoog Antink <rha@open.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds missing role attribute to the DCCP type, otherwise
the creation of entries is not of any use.
The attribute added is CTA_PROTOINFO_DCCP_ROLE which contains the
role of the conntrack original tuple.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit d0dba725 (netfilter: ctnetlink: add callbacks to the per-proto
nlattrs) changed the protocol registration function to abort if the
to-be registered protocol doesn't provide a new callback function.
The DCCP and UDP-Lite IPv6 protocols were missed in this conversion,
add the required callback pointer.
Reported-and-tested-by: Steven Jan Springl <steven@springl.ukfsn.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
From: Ursula Braun <ubraun@linux.vnet.ibm.com>
net/iucv/af_iucv.c in net-next-2.6 is almost correct. 4 lines should
still be deleted. These are the remaining changes:
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_MSGLIMIT socket option modifies the message limit for new
IUCV communication paths.
The message limit specifies the maximum number of outstanding messages
that are allowed for connections. This setting can be lowered by z/VM
when an IUCV connection is established.
Expects an integer value in the range of 1 to 65535.
The default value is 65535.
The message limit must be set before calling connect() or listen()
for sockets.
If sockets are already connected or in state listen, changing the message
limit is not supported.
For reading the message limit value, unconnected sockets return the limit
that has been set or the default limit. For connected sockets, the actual
message limit is returned. The actual message limit is assigned by z/VM
for each connection and it depends on IUCV MSGLIMIT authorizations
specified for the z/VM guest virtual machine.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb cannot be copied to user iovec, always return -EFAULT.
The skb is enqueued again, except MSG_PEEK flag is set, to allow user space
applications to correct its iovec pointer.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the socket type SOCK_SEQPACKET in addition to
SOCK_STREAM.
AF_IUCV sockets of type SOCK_SEQPACKET supports an 1:1 mapping of
socket read or write operations to complete IUCV messages.
Socket data or IUCV message data is not fragmented as this is the
case for SOCK_STREAM sockets.
The intention is to help application developers who write
applications or device drivers using native IUCV interfaces
(Linux kernel or z/VM IUCV interfaces).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow 'classification' of socket data that is sent or received over
an af_iucv socket. For classification of data, the target class of an
(native) iucv message is used.
This patch provides the cmsg interface for iucv_sock_recvmsg() and
iucv_sock_sendmsg(). Applications can use the msg_control field of
struct msghdr to set or get the target class as a
"socket control message" (SCM/CMSG).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch allows to send and receive data in the parameter list of an
iucv message.
The parameter list is an arry of 8 bytes that are used by af_iucv as
follows:
0..6 7 bytes for socket data and
7 1 byte to store the data length.
Instead of storing the data length directly, the difference
between 0xFF and the data length is used.
This convention does not interfere with the existing use of PRM
messages for shutting down the send direction of an AF_IUCV socket
(shutdown() operation). Data lenghts greater than 7 (or PRM message
byte 8 is less than 0xF8) denotes to special messages.
Currently, the special SEND_SHUTDOWN message is supported only.
To use IPRM messages, both communicators must set the IUCV_IPRMDATA
flag during path negotiation, i.e. in iucv_connect() and
path_pending().
To be compatible to older af_iucv implementations, sending PRM
messages is controlled by the socket option SO_IPRMDATA_MSG.
Receiving PRM messages does not depend on the socket option (but
requires the IUCV_IPRMDATA path flag to be set).
Sending/Receiving data in the parameter list improves performance for
small amounts of data by reducing message_completion() interrupts and
memory copy operations.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide the socket operations getsocktopt() and setsockopt() to enable/disable
sending of data in the parameter list of IUCV messages.
The patch sets respective flag only.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the af_iucv communication partner quiesces the path to shutdown its
receive direction, provide a quiesce callback implementation to shutdown
the (local) send direction. This ensures that both sides are synchronized.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the IUCV commands can be invoked in interrupt context.
Those commands need a different per-cpu IUCV command parameter block,
otherwise they might overwrite an IUCV command parameter of a not yet
finished IUCV command invocation in process context.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum sleep interval, for powersave purposes, is
determined by the DTIM period (it may not be larger)
and the required networking latency (it must be small
enough to fulfil those constraints).
This makes mac80211 calculate the maximum sleep interval
based on those constraints, and pass it to the driver.
Then the driver should instruct the device to sleep at
most that long.
Note that the device is responsible for aligning the
maximum sleep interval between DTIMs, we make sure it's
not longer but it needs to make sure it's between them.
Also, group some powersave documentation together and
make it more explicit that we support managed mode only,
and no IBSS powersaving (yet).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just setting IEEE80211_CONF_CHANGE_PS should be sufficient
for changes in the power saving things. The driver already
tells us whether it wants notification of dynps via the
"have dynps support" hw flag.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen Rothwell reported these warnings from a 32-bit build:
net/mac80211/mlme.c:1771: warning: left shift count >= width of type
net/mac80211/mlme.c:1772: warning: left shift count >= width of type
net/mac80211/mlme.c:1773: warning: left shift count >= width of type
net/mac80211/mlme.c:1774: warning: left shift count >= width of type
net/mac80211/mlme.c:1775: warning: left shift count >= width of type
This shows a bug in my code -- BIT(X) uses just "1 << X" which means
a 32-bit integer on 32-bit platforms, but the code here needs a u64
on all platforms. Fix this by using "1ULL << X" instead of BIT(X).
Thanks Stephen!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the RCU locking here we sleep while in an atomic context,
since we can sleep just use mutex locking for the interface
list instead of RCU. Sorry, seems I didn't get that in my UML
test.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it and use the proper type. To ease that adjust
struct ieee80211_tim_ie to have a virtual bitmap of size
at least 1.
Also check that the TIM IE is actually present before trying
to parse it!
Because other people may need the function, make it a static
inline in ieee80211.h.
(The original "mac80211: validate TIM IE length" was a minimal fix for
2.6.30. This purports to be the full, correct fix. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that these are exported is a technical detail
of the conversion period -- we don't want anybody to
start relying on these. Ultimately we want things to
use cfg80211 only, and once everything that is in wext
is converted to cfg80211 drivers will not need to touch
wext _at all_.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have ->deauth and ->disassoc we can support the
wext SIWMLME call directly without driver wext handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets IEEE80211_TX_CTL_CLEAR_PS_FILT for outgoing
frames for a half-wake station.
this is necessary if one wants to get ps-poll working properly with a p54 ap.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can allow scan requests in AP mode as long as the interface has not
yet been configured to send out Beacon frames (or if beaconing has
been disabled prior to the scan request). This makes it easier to scan
for neighboring BSSes during AP initialization and makes it possible
to run a scan without setting the interface down, if needed. Without
this change, the only available option would be to set the interface
down, move into station mode, and set the interface up, prior to
requesting the scan.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable PS by default (depending on Kconfig) -- rely on drivers
to control the level using pm_qos. Due to the previous patch
we turn off PS when necessary due to latency requirements.
This has a Kconfig symbol so people can, if they really want,
configure the default in their kernels. We may want to keep it
at "default y" only in wireless-testing for a while.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regardless of whether the hardware implements beacon filtering,
there's no need to process all beacons in software all the time
throughout the stack (mac80211 does a lot, then cfg80211, then
in the future possibly userspace).
This patch implements the "best possible" beacon filtering in
mac80211. "Best possible" means that it can look for changes in
all requested information elements, and distinguish vendor IEs
by their OUI.
In the future, we will add nl80211 API for userspace to request
information elements and vendor IE OUIs to watch -- drivers can
then implement the best they can do while software implements
it fully.
It is unclear whether or not this actually saves CPU time, but
the data is all in the cache already so it should be fairly
cheap. The additional _testing_, however, has great benefit;
Without this, and on hardware that doesn't implement beacon
filtering, wrong assumptions about, for example, scan result
updates could quickly creep into code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an application asks for a latency lower than the beacon interval
there's nothing we can do -- we need to stay awake and not have the
AP buffer frames for us. Add code to automatically calculate this
constraint in mac80211 so drivers need not concern themselves with it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When you have multiple virtual interfaces the current
implementation requires setting them up properly from
userspace, which is undesirable when we want to default
to power save mode. Keep track of powersave requested
from userspace per managed mode interface, and only
enable powersave globally when exactly one managed mode
interface is active and has powersave turned on.
Second, only start the dynPS timer when PS is turned
on, and properly turn it off when PS is turned off.
Third, fix the scan_sdata abuse in the dynps code.
Finally, also reorder the code and refactor the code
that enables PS or the dynps timer instead of having
it copied in two places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware defects may require the hardware to be re-initialised
completely from scratch. Drivers would need much information (for
instance the current MAC address, crypto keys, beaconing information,
etc.) stored duplicated from mac80211 to be able to do this, so let
mac80211 help them.
The new ieee80211_restart_hw() function requires the same code as
resuming, so move that code into a new ieee80211_reconfig() function
in util.c and leave only the suspend code in pm.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That will make the various cases where the WARN_ON
can happen distinguishable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill system fails to issue a LED trigger event when the rfkill state
changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the normal WPA or RSN case keys are only configured after
associating, so we should do that in that order when resuming
as well. It shouldn't really matter since we do not send any
data at either point, but iwlwifi prefers it this way and it
does seem more natural.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a netlink channel put helper, nl80211_msg_put_channel(),
which we will also make use of later for the beacon hints events.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of our documented API we always respect the orig_flag
settings on a channel. We forgot to follow this for the beacon
hints.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using nl80211 association, we need to send association response
with a failure code to user space SME instead of just internally
trying to send out the same (re)association request again couple of
times. This fixes problems in association process getting stuck on a
failure when user space is not notified in any way that something
actually failed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include the HT capabilities in the probe request frame.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added cfg80211_inform_bss() for full-mac devices to use.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It really belongs into that file since it is only relevant
for managed mode. Move 1:1, not even whitespace changes,
but make it static and remove from header file.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AUTH_TYPE is a required parameter for
NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to
open system authentication if the attribute is not specified. It is
better to just reject the invalid command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
