This patch adds the support for the L210/L220 (outer) cache
controller. The cache range operations are done by index/way since L2
cache controller only accepts physical addresses.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unconditionally disabling the PCKs (Programmable Clocks) is not a good
idea as it breaks boards that depend on those clocks being enabled by
bootloaders.
Therefore only disable unused clocks late in the init process, giving
the board init code the chance to claim the clock.
Patch from Steven Scholz.
Since the HCK clocks on SAM9261 are already being registered as a
independent clocks, we don't need the special case for HCK0 on the
SAM9261. Platform-init code and drivers should use the clock API to
enable/disable the clock.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Other platforms other than SMP may have an outer cache. For these, we
also need to mark the page table walks outer cacheable. Since marking
the walks always outer cacheable apparantly has no side effects, we
might as well always mark them so.
However, we continue to only mark PTWs shared if we have SMP enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In consistent_sync(), start + size can end up pointing one byte
beyond the end of the direct RAM mapping. We shouldn't BUG() when
this happens.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO pin setup should be handed by the platform-setup code, and not
directly by the driver.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an overrun in the AT91SAM9 gettimeoffset() function. This causes
the time value returned by gettimeofday() to jump "backwards".
Original patch from Michel Benoit.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the physically mapped flash on the Cogent CSB337 and CSB637
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the Timer/Counter Unit clocks on the AT91RM9200, AT91SAM9260 and
AT91SAM9261 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263-EK board.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263 processor. It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.
These changes are:
* The system peripheral I/O region we remap has increased from
0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
* The increased I/O region forces changes to entry-macro.S and
debug-macro.S due to ARM's limited immediate offset addressing
modes.
* Maximum number of GPIO banks increases to 5.
* 2 MMC controllers so the board-setup code needs to specify which
controller it wishes to use when calling at91_add_device_mmc().
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build failure of AT91SAM9260.
The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".
Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
#define eth_platform_data at91_eth_data
in board.h to keep the MACB driver happy.
Original patch by Jan Altenberg.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments. This leads to a little confusion
about what exactly they take. So, convert them to take const void *
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Memory allocated by the coherent memory allocators will be marked
uncacheable, which means it's pointless calling consistent_sync()
to perform cache maintainence on this memory; it's just a waste of
CPU cycles.
Moreover, with the (subsequent) merge of outer cache support, it
actually breaks things to call consistent_sync() on anything but
direct-mapped memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On newer architectures (ARMv6, ARMv7), the depth of the prefetch and
branch prediction is implementation defined and there is a small risk
of wrong ASID tagging when changing TTBR0 before setting the new
context id. The recommended solution is to set a reserved ASID during
TTBR changing. This patch reserves ASID 0.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up proc-xsc3:
- Correct a number of typos.
- Fix up indentation in a number of places.
- Change references to the various caches to be more clear about
whether we're talking about the L1 D, the L1 I or the unified L2
cache.
- Rename "drain write buffer" to "data write barrier", the official
name used in the Manzano manual.
- Change the xsc3 cpu name from "XScale-Core3" to "XScale-V3 based
processor".
Also, since a previously merged patch implements proper support for
using a MAC or iWMMXt coprocessor on xsc3 platforms, we no longer
need to enable access to CP0 on boot.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the setting of HWCAP_CRUNCH to kernel/crunch.c, where it belongs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bad_mode() currently prints the mode which caused the exception, and
then causes an oops dump to be printed which again displays this
information (since the CPSR in the struct pt_regs is correct.) This
leads to processor_modes[] being shared between traps.c and process.c
with a local declaration of it.
We can clean this up by moving processor_modes[] to process.c and
removing the duplication, resulting in processor_modes[] becoming
static.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the platform resources required to support the
ixp4xx-pata-cf libata driver on Avila Gateworks boards.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Gateworks Avila Network Platform in
a separate set of setup files to the IXDP425. This is necessary now
that a driver for the Avila CF card slot is available. It also adds
support for a minor variant on the Avila board known as the Loft,
which has a different number of maximum PCI devices.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes references to the Gateworks Avila Network
Platform in the ixdp425 setup code. Avila setup should occur
separately now that a CF ATA device driver is available.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the glue for ARM11 SMP oprofile support, which also supports the
performance monitor in the coherency unit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add oprofile glue for ARM11 (ARMv6) oprofile support. This
connects the ARM11 core profiling support to the oprofile code
for uniprocessor configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic support for the ARM11 profiling hardware. This is shared
between the ARM11 UP and ARM11 SMP oprofile support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 DMA selection code has the
arguments to writel() the wrong way around.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current lazy saving of the VFP registers is no longer possible
with thread migration on SMP. This patch implements a per-CPU
vfp-state pointer and the saving of the VFP registers at every context
switch. The registers restoring is still performed in a lazy way.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Supersections do not have a field for the domain and it is always
0. This patch prevents the creation of supersections during ioremap
when DOMAIN_IO is not zero (i.e. !defined(CONFIG_IO_36)).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchs allows the offset to the first page of
physical memory to be on any 2MB boundary
whereas the previous code could only handle psysical
offset to any 16MB boundary (0xNN000000) or any 1MB
boundary below 0x01000000 (e.g. 0x00N00000). The
problem is a consequence of the orr one-byte syntax,
so we fix this and we can place the first bank of
memory at 0x28e00000. I have also included an explicit
check that disallow compilation when PHYS_OFFSET is
not on a 2MiB boundary. head.S would be the proper place
to have this at since this is the first file that
attempts to use PHYS_OFFSET during compile.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cosmetic fix so iop333 is not reported as ixp46x
iop333 cpuid = 0x69054210
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
show_mem() was assuming incorrectly that the mem_map for any
node started at PFN 0. This is obviously wrong; fix it to
take account of node_start_pfn.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_gpio_getcfg() currently returns
a value which is dependant on the GPIO no
passed in. Now we have more generic constants
it is sensible to use those as return codes
so that any function dealing with >1 GPIO
does not need to do it's own number processing.
Since this function is only currently used in
pm.c, it is easy to fixup (and correct pm.c
to use the generic constants)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO bank A can only be output or a special
function, and the regs-gpio.h header has
mistakenly got this as input or output.
The mistake is carried on into the gpio.c
s3c2410_gpio_cfgpin() call which will set the
wrong value if S3C2410_GPIO_OUTPUT is passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The transition latency has to be defined and reasonably
small to allow on-demand and conservative governors.
The value has been defined according to manual.
The imx_set_target() protected against seen out of range
requests now.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup of at91 platform level gpio wake and suspend/resume logic.
The GPIO core now delegates wakeups to the parent AIC by refcounting,
and delegates clock management to the clock API. This makes these
system modules more independent of each other, which is cleaner and will
also help with the AT91SAM9263 (where some GPIO controllers share the
same irq and clock).
Original patch by David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements CPU and peripheral reset on AT91SAM9260 and
AT91SAM9261.
Original patch from Wojtek Kaniewski.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the legacy CONFIG_DEBUG_WAITQ from the SAM9260-EK and SAM9261-EK
default configuration files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current sched_clock() implementations on ARM cause unbootable kernels
with PRINTK_TIME support enabled. To avoid this, provide a basic
printk_clock() implementation which avoids sched_clock() being called
before the page tables have been set up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fuse does not work on ARM due to cache incoherency issues - fuse wants
to use get_user_pages() to copy data from the current process into
kernel space. However, since this accesses userspace via the kernel
mapping, the kernel mapping can be out of date wrt data written to
userspace.
This can lead to unpredictable behaviour (in the case of fuse) or data
corruption for direct-IO.
This resolves debian bug #402876
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the kernel attempts to execute a CP1 or CP2 instruction and it
aborts, and a FP emulator is not loaded, we try to return as if to
a user context, instead of the proper kernel context. Since the
fault came from kernel mode, we must use the kernel return paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include <asm/io.h> to fix the warning:
arch/arm/kernel/traps.c:647:6: warning: symbol '__readwrite_bug' was not declared. Should it be static?
Include <linux/mc146818rtc.h> to fix the warning:
arch/arm/kernel/time.c:42:1: warning: symbol 'rtc_lock' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we install the handlers for context switching, we must enable
VFP on all CPU cores, otherwise undefined (and random) effects
occur.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix apollon board compiler error
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix GPMC compiler errors on OMAP2
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If PG_dcache_dirty is set for a page, we need to flush the source page
before performing any copypage operation using a different virtual address.
This fixes the copypage implementations for XScale, StrongARM and ARMv6.
This patch fixes segmentation faults seen in the dynamic linker under
the usage patterns in glibc 2.4/2.5.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since iop13xx defines the PCI I/O spaces with physical resource addresses
the __io macro needs to perform the physical to virtual conversion. I
incorrectly assumed that this would be handled by ioremap, but drivers
(like e1000) directly dereference the address returned from __io.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit 505788cccb in linus kernel tree
introduced some printks (for debugging ?) which are flooding the logs on
my h1940. This patch replace them with pr_debug calls.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both CONFIG_MACH_OSIRIS and CONFIG_MACH_ANUBIS
should select CONFIG_PM_SIMTEC.
This patch moves the selection of CONFIG_PM_SIMTEC
to the machines that require it, as currently done
with other machines in the S3C2410 architecture.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the ep93xx, iop13xx, iop32x, iop33x, ixp2000, ixp23xx,
lpd270 and onearm defconfigs to 2.6.20-rc1.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Deepak Saxena has agreed to hand xsc3 maintainership over to me.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
LED 3 should have been registered with the
platform deviceid of 3, instead of 1 (which
was used for LED 1).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* use irq_chip
* use handle_level_irq
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch adds ifdefs around per cpu definitions. Otherwise, if
not all cpu types are selected, the kernel does not link.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The struct resource 'end' field is inclusive, the iop13xx flash
setup code got this wrong.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phys_io/io_pg_offst machine record variables were being set
to bogus values, causing problems when enabling DEBUG_LL.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add HWCAP_CRUNCH so that the dynamic linker knows whether it can
use Crunch-optimised libraries or not.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix up the CONFIG_PM mixups in arch/arm/mach-s3c2410/Kconfig
causing CONFIG_S3C2410_PM and CONFIG_PM_H1940 to get enabled
permanently.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move adjust_cr() into arch/arm/mm/mmu.c, and move irqflags.h to
a more appropriate place in the header file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean the includes in arch/arm/mach-s3c2410/s3c2440.c
and arch/arm/mach-s3c2410/s3c2442.c which should have
been pruned when these where split and updated.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove old changelog entries in arch/arm/mach-s3c2410
which should be available from the version control
system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the include/asm-arm/arch-s3c2410/regs-serial.h
platform data to use the prorper type (upf_t) for the
uart_flags.
Fix all the other parts of arch/arm/mach-s3c2410 to
include <linux/serial_core.h> and all other uses of
the include file.
mach-rx3715.c:101:18: warning: incorrect type in initializer (different base types)
mach-rx3715.c:101:18: expected unsigned long [unsigned] uart_flags
mach-rx3715.c:101:18: got restricted unsigned int [usertype] [force] <noident>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove warning from s3c2410_pm_resume() not being
declared by making it static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the following sparse errors in arch/arm/mach-s3c2410
by fixing the include paths and making un-exported items
static.
s3c2410-clock.c:206:12: warning: symbol 's3c2410_baseclk_add' was not declared. Should it be static?
s3c2412-clock.c:559:17: warning: symbol 'clks_src' was not declared. Should it be static?
s3c2412-clock.c:622:12: warning: symbol 'clks' was not declared. Should it be static?
s3c2412-clock.c:630:12: warning: symbol 's3c2412_baseclk_add' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove old (and non-shared) VA addresses from the mappings
in arch/arm/mach-s3c2410/map.h and anywhere they are being
mapped in arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse errors in arch/arm/mach-s3c2410/s3c2442-clock.c
warning: symbol 'clk_h' shadows an earlier one
warning: symbol 'clk_p' shadows an earlier one
warning: symbol 'clk_upll' shadows an earlier one
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the sparse errors in arch/arm/mach-s3c2410/s3c2440-clock.c
warning: symbol 'clk_h' shadows an earlier one
warning: symbol 'clk_p' shadows an earlier one
warning: symbol 'clk_upll' shadows an earlier one
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the copyright messages in arch/arm/mach-s3c2410
to actually have `Copyright` in the line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to ensure that the area size is page aligned so that
remap_area_pte() doesn't increment the address past the end of
the desired area.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add:
sys_unshare
sys_set_robust_list
sys_get_robust_list
sys_splice
sys_arm_sync_file_range
sys_tee
sys_vmsplice
sys_move_pages
sys_getcpu
Special note about sys_arm_sync_file_range(), which is implemented as:
asmlinkage long sys_arm_sync_file_range(int fd, unsigned int flags,
loff_t offset, loff_t nbytes)
{
return sys_sync_file_range(fd, offset, nbytes, flags);
}
We can't export sys_sync_file_range() directly on ARM because the
argument list someone picked does not fit in the available registers.
Would be nice if... there was an arch maintainer review mechanism for
new syscalls before they hit the kernel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4017/1: [Jornada7xx] - Updating Jornada720.c
[ARM] 3992/1: i.MX/MX1 CPU Frequency scaling support
[ARM] Provide a method to alter the control register
[ARM] 4016/1: prefetch macro is wrong wrt gcc's "delete-null-pointer-checks"
[ARM] Remove empty fixup function
[ARM] 4014/1: include drivers/hid/Kconfig
[ARM] 4013/1: clocksource driver for netx
[ARM] 4012/1: Clocksource for pxa
[ARM] Clean up ioremap code
[ARM] Unuse another Linux PTE bit
[ARM] Clean up KERNEL_RAM_ADDR
[ARM] Add sys_*at syscalls
[ARM] 4004/1: S3C24XX: UDC remove implict addition of VA to regs
[ARM] Formalise the ARMv6 processor name string
[ARM] Handle HWCAP_VFP in VFP support code
[ARM] 4011/1: AT91SAM9260: Fix compilation with NAND driver
[ARM] 4010/1: AT91SAM9260-EK board: Prepare for MACB Ethernet support
* HP Jornada 720 uses epson 1356 chip for graphics. This chip is compatible with s1d13xxxfb driver.
* HP Jornada 720 uses a Microprocessor Control Unit to talk to various
hardware. We add it as a platform device in jornada720_init()
* We provide pm_suspend() to avoid unresolved symbols in apm.o. We are
unable to truly suspend now, hence the stub.
* Speaker/microphone enabling got removed because it will be placed in the alsa driver.
Signed-off-by: Filip Zyzniewski <(address hidden)>
Signed-off-by: Kristoffer Ericson <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support to change MX1 CPU frequency at runtime.
Tested on PiKRON's PiMX1 board and seems to be fully
stable up to 200 MHz end even as low as 8 MHz.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some of the header file rearrangements broke the build for board-osk.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
More fixes to build breakage from the work_struct changes ... this updates
the tps65010 driver. Plus, fix some dependencies related to the way it's
used on the OMAP OSK: force static linking there, since the resulting
kernel can't link.
NOTE that until the i2c core gets fixed to work without SMBUS_QUICK,
kernels needing this driver must still use "tps65010.force=0,0x48" on the
command line.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HID drivers are in their own directory now, so we have to
include the Kconfig file for arm.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a clocksource driver for netx systems
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a clocksource driver for pxa2xx systems
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we're keeping the ioremap code, we might as well keep it as
close to the standard kernel as possible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
L_PTE_ASID is not really required to be stored in every PTE, since we
can identify it via the address passed to set_pte_at(). So, create
set_pte_ext() which takes the address of the PTE to set, the Linux
PTE value, and the additional CPU PTE bits which aren't encoded in
the Linux PTE value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Clean up the KERNEL_RAM_ADDR stuff in arch/arm/kernel/head.S to
make it clearer what's referring to what. In doing so, remove
the usage of __virt_to_phys(), which is not guaranteed to be
something that the assembler can parse.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the I2C bus found on the ARM Versatile and Realview
platforms. The I2C bus has a RTC and optionally some EEPROMs attached.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
New I2C bus driver for Philips ARM boards (Philips IP3204 I2C IP
block). This I2C controller can be found on (at least) PNX010x,
PNX52xx and PNX4008 Philips boards.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't set HWCAP_VFP in the processor support file; not only does it
depend on the processor features, but it also depends on the support
code being present. Therefore, only set it if the support code
detects that we have a VFP coprocessor attached.
Also, move the VFP handling of the coprocessor access register into
the VFP support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add missing include for NAND device support on AT91SAM9260.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add PHY IRQ pin definition for AT91SAM9260-EK board.
Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not bother masking/unmasking the parent IRQ
for the mulitplexed EINT irqs, as masking the
leaf seems to be fine.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that include/asm-arm/bug.h requires include/linux/stddef.h
for the definition of NULL. It seems that stddef.h was always included
indirectly in most cases, and that issue was properly fixed a while ago.
Then commit 5047f09b56 incorrectly reverted
change from commit ff10952a54 (bad dwmw2)
and the problem recently resurfaced.
Because the third argument to __bug() is never used anyway, RMK suggested
getting rid of it entirely instead of readding #include <linux/stddef.h>
which this patch does.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the mapping for the third S3C2440 serial
port into the default serial devices for the
Osiris.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RX3715 is similar to the H1940 in the way
that suspend to RAM works, so we can use most
of the extant support for the H1940 with only
a few modifictions
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the GPIO attached LEDs on the VR1000
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The iop348 processor integrates an Xscale (XSC3 512KB L2 Cache) core with a
Serial Attached SCSI (SAS) controller, multi-ported DDR2 memory
controller, 3 Application Direct Memory Access (DMA) controllers, a 133Mhz
PCI-X interface, a x8 PCI-Express interface, and other peripherals to form
a system-on-a-chip RAID subsystem engine.
The iop342 processor replaces the SAS controller with a second Xscale core
for dual core embedded applications.
The iop341 processor is the single core version of iop342.
This patch supports the two Intel customer reference platforms iq81340mc
for external storage and iq81340sc for direct attach (HBA) development.
The developer's manual is available here:
ftp://download.intel.com/design/iio/docs/31503701.pdf
Changelog:
* removed virtual addresses from resource definitions
* cleaned up some unnecessary #include's
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This creates a new RTC-framework driver for the RTC/calendar module found
in various OMAP1 chips. (OMAP2 and OMAP3 use external RTCs, like those in
TI's multifunction PM companion chips.) It's been in the Linux-OMAP tree
for several months now, and other trees before that, so it's quite stable.
The most notable issue is that the OMAP IRQ code doesn't yet support the
RTC IRQ as a wakeup event. Once that's fixed, a patch will be needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In light of the recent pagefault and filemap_copy_from_user work I've gone
through all the arch pagefault handlers to make sure the inc_preempt_count()
'feature' works as expected.
Several sections of code (including the new filemap_copy_from_user) rely on
the fact that faults do not take locks under increased preempt count.
arch/x86_64 - good
arch/powerpc - good
arch/cris - fixed
arch/i386 - good
arch/parisc - fixed
arch/sh - good
arch/sparc - good
arch/s390 - good
arch/m68k - fixed
arch/ppc - good
arch/alpha - fixed
arch/mips - good
arch/sparc64 - good
arch/ia64 - good
arch/arm - fixed
arch/um - good
arch/avr32 - good
arch/h8300 - NA
arch/m32r - good
arch/v850 - good
arch/frv - fixed
arch/m68knommu - NA
arch/arm26 - fixed
arch/sh64 - fixed
arch/xtensa - good
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For some reason, gcc was calculating meminfo.bank[meminfo.nr_banks]
repeatedly. Use a pointer to it instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enhanced resolution for time measurement functions.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The future high resolution support inclusion utilizes
imx_decode_pll() in timer base frequency computation.
This use requires more precise computation without
discarding 10 bits by shifting left.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support to suspend and resume, using the
H1940's bootloader
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using a device_initcall() for the clocksource initialization, just call the init from the sys_timer init function.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PCI master abort handling issue that affected ixp2000 also
affects ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here's a 63-bit implementation of shed_clock() for PXA2xx. The actual
period depends on the value of CLOCK_TICK_RATE and whether or not
reduced scaling factors were provided for it.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
period
This provides a 63 bit clock counter guaranteed to be monotonic over a
period of 35583 days instead of a clock wrap every 179 seconds, as long
as sched_clock() is called at least once every 89 seconds. This should
not be a problem in practice, although a kernel timer could be scheduled
every 80 seconds for example simply to call sched_clock() making sure
top bits are always synchronized if need be.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This provides a 63 bit clock counter guaranteed to be monotonic over a
period of 370 days instead of a clock wrap every 19.4 minutes, as long
as sched_clock() is called at least once every 9.7 minutes which
shouldn't be a problem in practice.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Cirrus Logic EDB9302A Evaluation Board. Confirmed
to work by Chase Douglas.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not assume that the ARM GCC toolchain defaults to building for the
32-bit ARM ISA (-marm) case. Instead, explicitly select -marm in CFLAGS
since the toolchain default can be for the 16-bit Thumb ISA (-mthumb) in
some odd/rare cases.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.
This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers. Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)
Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch. Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.
CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.
This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.' This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.
These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove BTB_ENABLE from proc-xsc3.S
On some early revisions of xsc3 enabling the branch target buffer can cause
crashes, see erratum #42.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge L_PTE_COHERENT with L_PTE_SHARED and free up a L_PTE_* bit.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create include/asm-arm/arch-ixp4xx/udc.h and
add platfrom device ixp4xx_udc_device into
arch/arm/mach-ixp4xx/common.c.
This allows us to use pxa2xx-udc on
the ixp4xx platfrom. Both pxa2xx and
ixp4xx use the same device controller.
Signed-off-by:Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains various updates the at91rm9200_devices.c file:
* Consistent naming of resources and platform_devices.
* PCMCIA/Compact Flash: Configuration of the memory controller
moved out of the driver and into this file.
* MMC: Enable the VCC pin (if one is configured)
* MMC: Enable the internal pullups on the I/O pins.
* NAND: Configuration of the memory controller moved out of the
driver and into this file.
* Added TWI/I2C resources.
* The names of some of the CONFIG_ variables were changed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Atmel AT91SAM9261-EK board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Atmel AT91SAM9260-EK board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The master abort check in ixp2000_pci_read_config() recently started
failing due to the compiler optimising out the read access following
the clearing of pci_master_aborts. Mark pci_master_aborts volatile to
force the compiler to reload it on every use.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add initial board support for the ADS Sphere board.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.
* Can only select support for one AT91 processor at a time.
* Remove most of the remaining static memory mapping for the
AT91RM9200.
* Reserve 1Mb of memory below the IO for mapping the internal SRAM
and any custom board-specific devices (ie, FPGA).
* The SAM9260 has more serial ports, so increase the maximum to 7.
* Define the standard chipselect addresses, and define other
addresses relative to those.
* CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bits used to select the USB clocks are different on the SAM9's.
Add support for the HCK clocks on the AT91SAM9261.
Patch from Patrice Vilchez & Nicolas Ferre
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new
physmap API by creating a physmap platform device for the NOR flash
found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the Carmeva board support:
* Specify the MMC Write-protect and Detection pins.
* Add configuration of SPI devices.
Patch from Peer Georgi.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached is a patch for at91rm9200_time.c which removes
the 'BUG: soft lockup detected on CPU#0!' message when
exiting suspended states.
Patch from Savin Zlobec
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch includes the pin initialization, resource definition and
registration of the platform_devices for the SAM9260 and SAM9261
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the timer on the Atmel AT91SAM9261 and AT91SAM9260
processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the initial support for the newer Atmel AT91SAM9261 and
AT91SAM9260 processors. The code is based on, and makes use of, the
existing AT91RM9200 support.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The external interrupt sources are different on the various AT91
processors. This patch introduces the global 'at91_extern_irq' variable
that contains a bitset of the available external interrupt sources.
The processor reset mechanism also differs on the various AT91
processors. This patch also adds a global 'at91_arch_reset' callback
(from system.h) into the processor-specific code to perform the reset.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch renames the arch/arm/mach-at91rm9200/devices.c file to
at91rm9200_devices.c. The file contains AT91RM9200-specific code, so we
will need separate files for the SAM9 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point having the Versatile PB initialisation using an
arch_initcall() and then checking whether it's running on a
Versatile PB board - this is what the .init_machine function
pointer in the machine description is for. Use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove ARM local cache of 4 struct thread_info.
Can cause oops under certain circumstances.
Russell indicated the original optimization was
required on older kernels to avoid thread starvation
on memory fragmentation, but may no longer be
required. I've updated the patch to 19rc4 and
ensured no <config.h> dain-bramage slipped in this
time (sorry about that).
Original description follows:
I was given some test results which pointed to an
Oops in alloc_thread_info (happened 2x), and after
looking at the code, I see that ARM has its own
local cache of 4 struct thread_info. There wasn't
any clear (to me) synchronization between the
alloc_thread_info and the free_thread_info.
I looked over the other arch, and they all simply
allocate them on an as needed basis, so I simplified
the ARM to do the same, based on the other arch
(e.g. PPC) and the folks doing the testing have
indicated that this fixed the oops.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix warnings and errors in arch/arm/mm for nommu build.
Remove commented out function prototype in pgtable-nommu.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't reset OSCR to zero as this prevents us from having a contiguous
time source. The value returned by sched_clock() is reset to zero in the
middle of the boot process otherwise, making CONFIG_PRINTK_TIME rather
messed up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't reset OSCR to zero as this prevents us from having a contiguous
time source. The value returned by sched_clock() is reset to zero in the
middle of the boot process otherwise, making CONFIG_PRINTK_TIME rather
messed up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_WAITQ appears to have been removed by others, but no one
removed the configuration option from ARM. Remote it from both
Kconfig.debug and all default configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an apparant hang with the "apm -s" command. We omitted to wake up
this process once resume had completed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The APM emulation can sometimes cause suspend to fail to work due
to apparantly waiting for some process to acknowledge an event when
it actually has already done so. We re-jig the event handling to
work around this behaviour.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Eliminate two warnings:
kernel/power/pm.c:205: warning: 'pm_register' is deprecated (declared at kernel/power/pm.c:64)
kernel/power/pm.c:206: warning: 'pm_send_all' is deprecated (declared at kernel/power/pm.c:180)
by updating defconfig files to contain a sensible PM_LEGACY default.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/*
* Note: Drivers should NOT use this function directly, as it will break
* platforms with CONFIG_DMABOUNCE.
* Use the driver DMA support - see dma-mapping.h (dma_sync_*)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove two warnings:
drivers/serial/8250_early.c:136: warning: unused variable 'mapsize'
include/linux/io.h:47: warning: passing argument 1 of '__readb' discards qualifiers from pointer target type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM doesn't source drivers/Kconfig like most architectures do, so the
newly added drivers/ata is currently not made available on ARM. SATA
is used on some ARM machines, like the Thecus N2100, so we need to
source drivers/ata/Kconfig.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OP_MAX_COUNTER never referenced, and is a reminant of an earlier
oprofile implementation. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most ARM defconfigs don't actually need to have PM_LEGACY enabled.
Disable it for ATEB9200, Collie, IXP4xx, OMAP H2, S3C2410 and
Versatile.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds platform devices' registration for the devices which drivers
either have been added to the mainline or on the way to.
arch/arm/mach-pnx4008/core.c | 69 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
show_mem() was not correctly handling holes in the memory
map. It was treating the freed sections of the map as
though they contained valid struct page entries. This
could cause incorrect debugging output or even a kernel
panic.
This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory. show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: Ray Lehtiniemi <rayl@mail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The timer LED is unusable at HZ=large, since it's got
a hard-wired value of 100 ticks per cycle; when HZ=1024
(for example) it's essentially always-on. This patch
just makes that be HZ ticks per cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the new drivers, such as SPI, LED and RTC core,
to the s3c2410_defconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.irg>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the bast_defconfig, as it has not been updated
since 2.6.13. The s3c2410_defconfig should be a good
replacement.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the smdk2410_defconifg as it is out of data
and has not been touched since 2.6.11.
Use the s3c2410_defconfig instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a rework of the ixp4xx irq_chip implementation. The use of
two irq_chip structures and potentially switching between them is a
violation of the intended use of the IRQ framework. The current
implementation does not work with current in-kernel spinlock debugging
or lockdep due to lock recursion problems caused by calling
set_irq_chip/handler from within the chip's set_irq_type().
This patch goes back to using one irq_chip structure and handling the
differences between edge/level, normal/GPIO interrupts inside the
ack/mask/unmask routines themselves.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM patch 3756/1 added HWCAP_IWMMXT. This patch adds support
for broadcasting that info via /proc/cpuinfo and sets it for
the CPU features of the PXA270.
I've booted 19rc3 on a pxa270 and confirmed that the /proc/cpuinfo
shows "iwmmxt" in the Features.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s3c2410_gpio_getirq() holds for the S3C2412 build,
so ensure that it gets built for all the current
S3C24XX architectures
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_sync_single is no more (and to be removed in 2.7) so this export should be dma_sync_single_for_cpu.
Also export dma_sync_single_for_device.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"K4S281632b-1H" should read "K4S281632B-1H" (As it does everywhere
else). No more coffe!
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second ethernet port on the Thecus n2100 was incorrectly assigned
to XINT1 instead of the correct XINT3 (PCI INTB instead of INTD), which
caused that port to be non-functional.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for KBUILD_IMAGE on ARM. This takes the usual target
specifiers (zImage/Image/etc) in the same way that powerpc does
(iow, without the arch/arm/boot prefix).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SIGFPE signal should be generated if Division by Zero exception is detected.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The significand should be shifted until the value of bit [62] is 1
to normalize the denormal double number.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IRQ changes a while back broke the build for SMP machines.
Fix up the SMP code to use set_irq_regs/get_irq_regs as
appropriate. Also, fix a warning in arch/arm/kernel/time.c
where 'regs' becomes unused for SMP builds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HAS_TOUCHSCREEN_ADS7843_LH7 and HAS_TOUCHSCREEN_ADC_LH7 are referenced
but not defined in the LH7A40x configuration. Comment them out to
prevent them causing warnings.
Marc Singer said:
Feel free to remove the Kconfig lines. I'll add it back with
the rest of the config entries.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix one more compile breakage caused by the post -rc1 IRQ changes.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
