commit 88bf56d04bc3564542049ec4ec168a8b60d0b48c upstream.
In kvm_mmu_notifier_invalidate_range_start(), tlbs_dirty is used as:
need_tlb_flush |= kvm->tlbs_dirty;
with need_tlb_flush's type being int and tlbs_dirty's type being long.
It means that tlbs_dirty is always used as int and the higher 32 bits
is useless. We need to check tlbs_dirty in a correct way and this
change checks it directly without propagating it to need_tlb_flush.
Note: it's _extremely_ unlikely this neglecting of higher 32 bits can
cause problems in practice. It would require encountering tlbs_dirty
on a 4 billion count boundary, and KVM would need to be using shadow
paging or be running a nested guest.
Cc: stable@vger.kernel.org
Fixes: a4ee1ca4a3 ("KVM: MMU: delay flush all tlbs on sync_page path")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20201217154118.16497-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39b4d43e6003cee51cd119596d3c33d0449eb44c upstream.
Get the so called "root" level from the low level shadow page table
walkers instead of manually attempting to calculate it higher up the
stack, e.g. in get_mmio_spte(). When KVM is using PAE shadow paging,
the starting level of the walk, from the callers perspective, is not
the CR3 root but rather the PDPTR "root". Checking for reserved bits
from the CR3 root causes get_mmio_spte() to consume uninitialized stack
data due to indexing into sptes[] for a level that was not filled by
get_walk(). This can result in false positives and/or negatives
depending on what garbage happens to be on the stack.
Opportunistically nuke a few extra newlines.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aa078932ff6c66bf10cc5b3144440dbfa7d813d upstream.
Return -1 from the get_walk() helpers if the shadow walk doesn't fill at
least one spte, which can theoretically happen if the walk hits a
not-present PDPTR. Returning the root level in such a case will cause
get_mmio_spte() to return garbage (uninitialized stack data). In
practice, such a scenario should be impossible as KVM shouldn't get a
reserved-bit page fault with a not-present PDPTR.
Note, using mmu->root_level in get_walk() is wrong for other reasons,
too, but that's now a moot point.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1c5246e08eb64991001d97a3bd119c93edbc79a upstream.
Commit
28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
introduced a new location where a pmd was released, but neglected to
run the pmd page destructor. In fact, this happened previously for a
different pmd release path and was fixed by commit:
c283610e44 ("x86, mm: do not leak page->ptl for pmd page tables").
This issue was hidden until recently because the failure mode is silent,
but commit:
b2b29d6d01 ("mm: account PMD tables like PTE tables")
turns the failure mode into this signature:
BUG: Bad page state in process lt-pmem-ns pfn:15943d
page:000000007262ed7b refcount:0 mapcount:-1024 mapping:0000000000000000 index:0x0 pfn:0x15943d
flags: 0xaffff800000000()
raw: 00affff800000000 dead000000000100 0000000000000000 0000000000000000
raw: 0000000000000000 ffff913a029bcc08 00000000fffffbff 0000000000000000
page dumped because: nonzero mapcount
[..]
dump_stack+0x8b/0xb0
bad_page.cold+0x63/0x94
free_pcp_prepare+0x224/0x270
free_unref_page+0x18/0xd0
pud_free_pmd_page+0x146/0x160
ioremap_pud_range+0xe3/0x350
ioremap_page_range+0x108/0x160
__ioremap_caller.constprop.0+0x174/0x2b0
? memremap+0x7a/0x110
memremap+0x7a/0x110
devm_memremap+0x53/0xa0
pmem_attach_disk+0x4ed/0x530 [nd_pmem]
? __devm_release_region+0x52/0x80
nvdimm_bus_probe+0x85/0x210 [libnvdimm]
Given this is a repeat occurrence it seemed prudent to look for other
places where this destructor might be missing and whether a better
helper is needed. try_to_free_pmd_page() looks like a candidate, but
testing with setting up and tearing down pmd mappings via the dax unit
tests is thus far not triggering the failure.
As for a better helper pmd_free() is close, but it is a messy fit
due to requiring an @mm arg. Also, ___pmd_free_tlb() wants to call
paravirt_tlb_remove_table() instead of free_page(), so open-coded
pgtable_pmd_page_dtor() seems the best way forward for now.
Debugged together with Matthew Wilcox <willy@infradead.org>.
Fixes: 28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/160697689204.605323.17629854984697045602.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2407cf7d22d0c0d94cf20342b3b8f06f1d904e7 upstream.
Ever since commit 2a9127fcf2 ("mm: rewrite wait_on_page_bit_common()
logic") we've had some very occasional reports of BUG_ON(PageWriteback)
in write_cache_pages(), which we thought we already fixed in commit
073861ed77 ("mm: fix VM_BUG_ON(PageTail) and BUG_ON(PageWriteback)").
But syzbot just reported another one, even with that commit in place.
And it turns out that there's a simpler way to trigger the BUG_ON() than
the one Hugh found with page re-use. It all boils down to the fact that
the page writeback is ostensibly serialized by the page lock, but that
isn't actually really true.
Yes, the people _setting_ writeback all do so under the page lock, but
the actual clearing of the bit - and waking up any waiters - happens
without any page lock.
This gives us this fairly simple race condition:
CPU1 = end previous writeback
CPU2 = start new writeback under page lock
CPU3 = write_cache_pages()
CPU1 CPU2 CPU3
---- ---- ----
end_page_writeback()
test_clear_page_writeback(page)
... delayed...
lock_page();
set_page_writeback()
unlock_page()
lock_page()
wait_on_page_writeback();
wake_up_page(page, PG_writeback);
.. wakes up CPU3 ..
BUG_ON(PageWriteback(page));
where the BUG_ON() happens because we woke up the PG_writeback bit
becasue of the _previous_ writeback, but a new one had already been
started because the clearing of the bit wasn't actually atomic wrt the
actual wakeup or serialized by the page lock.
The reason this didn't use to happen was that the old logic in waiting
on a page bit would just loop if it ever saw the bit set again.
The nice proper fix would probably be to get rid of the whole "wait for
writeback to clear, and then set it" logic in the writeback path, and
replace it with an atomic "wait-to-set" (ie the same as we have for page
locking: we set the page lock bit with a single "lock_page()", not with
"wait for lock bit to clear and then set it").
However, out current model for writeback is that the waiting for the
writeback bit is done by the generic VFS code (ie write_cache_pages()),
but the actual setting of the writeback bit is done much later by the
filesystem ".writepages()" function.
IOW, to make the writeback bit have that same kind of "wait-to-set"
behavior as we have for page locking, we'd have to change our roughly
~50 different writeback functions. Painful.
Instead, just make "wait_on_page_writeback()" loop on the very unlikely
situation that the PG_writeback bit is still set, basically re-instating
the old behavior. This is very non-optimal in case of contention, but
since we only ever set the bit under the page lock, that situation is
controlled.
Reported-by: syzbot+2fc0712f8f8b8b8fa0ef@syzkaller.appspotmail.com
Fixes: 2a9127fcf2 ("mm: rewrite wait_on_page_bit_common() logic")
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84e261553e6f919bf0b4d65244599ab2b41f1da5 upstream.
hwmon, specifically hwmon_num_channel_attrs, expects the config
array in the hwmon_channel_info structure to be terminated by
a zero entry. amd_energy does not honor this convention. As
result, a KASAN warning is possible. Fix this by adding an
additional entry and setting it to zero.
Fixes: 8abee9566b ("hwmon: Add amd_energy driver to report energy counters")
Signed-off-by: David Arcari <darcari@redhat.com>
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20210107144707.6927-1-darcari@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an unused variable which was mistakingly left by commit
37faf5061541 ("USB: serial: keyspan_pda: fix write-wakeup
use-after-free") and only removed by a later change.
This is needed to suppress a W=1 warning about the unused variable in
the stable trees that the build bots triggers.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64e6bbfff52db4bf6785fab9cffab850b2de6870 upstream.
There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.
Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL
Context 2:
gadget_dev_desc_UDC_show()-> access udc_name
Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38
Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cd0fe91387917be48e91385a572a69dfac2f3f7 upstream.
When binding the ConfigFS gadget to a UDC, the functions in each
configuration are added in list order. However, if usb_add_function()
fails, the failed function is put back on its configuration's
func_list and purge_configs_funcs() is called to further clean up.
purge_configs_funcs() iterates over the configurations and functions
in forward order, calling unbind() on each of the previously added
functions. But after doing so, each function gets moved to the
tail of the configuration's func_list. This results in reshuffling
the original order of the functions within a configuration such
that the failed function now appears first even though it may have
originally appeared in the middle or even end of the list. At this
point if the ConfigFS gadget is attempted to re-bind to the UDC,
the functions will be added in a different order than intended,
with the only recourse being to remove and relink the functions all
over again.
An example of this as follows:
ln -s functions/mass_storage.0 configs/c.1
ln -s functions/ncm.0 configs/c.1
ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd
echo "<udc device>" > UDC # fails
start adbd
echo "<udc device>" > UDC # now succeeds, but...
# bind order is
# "ADB", mass_storage, ncm
[30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30133.119974] using random self ethernet address
[30133.120002] using random host ethernet address
[30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26
[30133.140015] usb0: MAC 6e:28:7e:42:66:6a
[30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19
[30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200
[30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00
[30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19
[30136.661933] init: starting service 'adbd'...
[30136.700126] read descriptors
[30136.700413] read strings
[30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30138.575631] using random self ethernet address
[30138.575660] using random host ethernet address
[30138.595338] usb0: HOST MAC 2e:cf:43💿ca:c8
[30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0
[30138.791490] configfs-gadget gadget: super-speed config #1: c
Fix this by reversing the iteration order of the functions in
purge_config_funcs() when unbinding them, and adding them back to
the config's func_list at the head instead of the tail. This
ensures that we unbind and unwind back to the original list order.
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc35c224a80aa5a5a539510ef049faf0d6ed181 upstream.
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a88fa221ce911c331bf700d2214c5b2f77414d3 upstream.
Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.
Fixes: bba787a860 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cc332e4ee4febcbb685e2962ad323fe4b3b750a upstream.
When printer driver is loaded, the printer_func_bind function is called, in
this function, the interface descriptor be allocated memory, if after that,
the error occurred, the interface descriptor memory need to be free.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9389044f27081d6ec77730c36d5bf9a1288bcda2 upstream.
With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c318840fb2a42ce25febc95c4c19357acf1ae5ca upstream.
The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid. With URBs
sent from userspace via usbfs, that assumption can be violated.
In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests. Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits. Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.
This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings. It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c06ccf3ebb7503706ea49fd248e709287ef385a3 upstream.
The calculation of in_cables and out_cables bitmaps are done with the
bit shift by the value from the descriptor, which is an arbitrary
value, and can lead to UBSAN shift-out-of-bounds warnings.
Fix it by filtering the bad descriptor values with the check of the
upper bound 0x10 (the cable bitmaps are 16 bits).
Reported-by: syzbot+92e45ae45543f89e8c88@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223174557.10249-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 020a1f453449294926ca548d8d5ca970926e8dfd upstream.
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 372c93131998c0622304bed118322d2a04489e63 upstream.
Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.
Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.
Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54d0a3ab80f49f19ee916def62fe067596833403 upstream.
Stack-allocated buffers cannot be used for DMA (on all architectures) so
allocate the flush command buffer using kmalloc().
Fixes: 60a8fc0171 ("USB: add iuu_phoenix driver")
Cc: stable <stable@vger.kernel.org> # 2.6.25
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96ebc9c871d8a28fb22aa758dd9188a4732df482 upstream.
Here's another variant PNY Pro Elite USB 3.1 Gen 2 portable SSD that
hangs and doesn't respond to ATA_1x pass-through commands. If it doesn't
support these commands, it should respond properly to the host. Add it
to the unusual uas list to be able to move forward with other
operations.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2edc7af892d0913bf06f5b35e49ec463f03d5ed8.1609819418.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 718bf42b119de652ebcc93655a1f33a9c0d04b3c upstream.
Fix shift out-of-bounds in vhci_hcd.c:
UBSAN: shift-out-of-bounds in ../drivers/usb/usbip/vhci_hcd.c:399:41
shift exponent 768 is too large for 32-bit type 'int'
Fixes: 03cd00d538 ("usbip: vhci-hcd: Set the vhci structure up to work")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+297d20e437b79283bf6d@syzkaller.appspotmail.com
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201229071309.18418-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760 upstream.
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4ca3fce90a37b23a77bfcc86800d484a80514 upstream.
First of all the commit e0082698b6 ("usb: dwc3: ulpi: conditionally
resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression,
as by design of the fix any attempt to read/write from/to the PHY control
registers will completely disable the PHY suspension, which consequently
will increase the USB bus power consumption. Secondly the fix won't work
well for the very first attempt of the ULPI PHY control registers IO,
because after disabling the USB2.0 PHY suspension functionality it will
still take some time for the bus to resume from the sleep state if one has
been reached before it. So the very first PHY register read/write
operation will take more time than the busy-loop provides and the IO
timeout error might be returned anyway.
Here we suggest to fix the denoted problems in the following way. First of
all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to
make the controller and the USB2.0 bus more power efficient. Secondly
instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms
sleep if the PHY suspension is enabled (1ms should be enough as by LPM
specification it is at most how long it takes for the USB2.0 bus to resume
from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension
functionality has been disabled on the DWC USB3 controller setup procedure
we'll compensate the USB bus resume process latency by extending the
busy-loop attempts counter.
Fixes: e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca3f138105727c3a22edda32d02f91ce1bf11c9 upstream.
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce722da66d3e9384aa2de9d33d584ee154e5e157 upstream.
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5c7682aaaa10e42928d73de1c9e1e02d2b14c2e upstream.
If an active transfer is dequeued, then the endpoint is freed to start a
new transfer. Make sure to clear the endpoint's transfer wait flag for
this case.
Fixes: e0d19563eb ("usb: dwc3: gadget: Wait for transfer completion")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b81cd5b5281cfbfdadb002c4bcf5c9be7c017cfd.1609828485.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1383b3537a7bea1c213baa7878ccc4ecf4413b5 upstream.
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f041b8592daaaea46e91a8ebb3b47e6e0171fd8 upstream.
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e5ff0b4b6bcb4d17b7a26ec8bcfc7dd4651684f upstream.
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ffc76539e6e8d28114f95ac25c167c37b5191b3 upstream.
This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2459108b5a0604c4b472cae2b3cb8d3444c77fb upstream.
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d887d6104adeb94d1b926936ea21f07367f0ff9f upstream.
If an error occurs after calling 'mtk_hsdma_init()', it must be undone by
a corresponding call to 'mtk_hsdma_uninit()' as already done in the
remove function.
Fixes: 0853c7a53e ("staging: mt7621-dma: ralink: add rt2880 dma engine")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201213153513.138723-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cab36da4bf1a35739b091b73714a39a1bbd02b05 upstream.
Return -EFAULT on error instead of the number of bytes remaining to be
copied.
Fixes: bac42fb212 ("comedi: get rid of compat_alloc_user_space() mess in COMEDI_CMD{,TEST} compat")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/X8c3pfwFy2jpy4BP@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce47d95b7346dcafd9bed3556a8d072cb2b8571 upstream.
Commit eff8728fe6 ("vmlinux.lds.h: Add PGO and AutoFDO input
sections") added ".text.unlikely.*" and ".text.hot.*" due to an LLVM
change [1].
After another LLVM change [2], these sections are seen in some PowerPC
builds, where there is a orphan section warning then build failure:
$ make -skj"$(nproc)" \
ARCH=powerpc CROSS_COMPILE=powerpc64le-linux-gnu- LLVM=1 O=out \
distclean powernv_defconfig zImage.epapr
ld.lld: warning: kernel/built-in.a(panic.o):(.text.unlikely.) is being placed in '.text.unlikely.'
...
ld.lld: warning: address (0xc000000000009314) of section .text is not a multiple of alignment (256)
...
ERROR: start_text address is c000000000009400, should be c000000000008000
ERROR: try to enable LD_HEAD_STUB_CATCH config option
ERROR: see comments in arch/powerpc/tools/head_check.sh
...
Explicitly handle these sections like in the main linker script so
there is no more build failure.
[1]: https://reviews.llvm.org/D79600
[2]: https://reviews.llvm.org/D92493
Fixes: 83a092cf95 ("powerpc: Link warning for orphan sections")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1218
Link: https://lore.kernel.org/r/20210104205952.1399409-1-natechancellor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f93274ef0fe972c120c96b3207f8fce376231a60 upstream.
The function derive_pub_key() should be calling memzero_explicit()
instead of memset() in case the complier decides to optimize away the
call to memset() because it "knows" no one is going to touch the memory
anymore.
Cc: stable <stable@vger.kernel.org>
Reported-by: Ilil Blum Shem-Tov <ilil.blum.shem-tov@intel.com>
Tested-by: Ilil Blum Shem-Tov <ilil.blum.shem-tov@intel.com>
Link: https://lore.kernel.org/r/X8ns4AfwjKudpyfe@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aa171e9b267ce7c52d3a3df7bc9c1fc0203dec5 upstream.
Pavel reports that commit 17858b140bf4 ("crypto: ecdh - avoid unaligned
accesses in ecdh_set_secret()") fixes one problem but introduces another:
the unconditional memcpy() introduced by that commit may overflow the
target buffer if the source data is invalid, which could be the result of
intentional tampering.
So check params.key_size explicitly against the size of the target buffer
before validating the key further.
Fixes: 17858b140bf4 ("crypto: ecdh - avoid unaligned accesses in ecdh_set_secret()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52abca64fd9410ea6c9a3a74eab25663b403d7da ]
blk_queue_enter() accepts BLK_MQ_REQ_PM requests independent of the runtime
power management state. Now that SCSI domain validation no longer depends
on this behavior, modify the behavior of blk_queue_enter() as follows:
- Do not accept any requests while suspended.
- Only process power management requests while suspending or resuming.
Submitting BLK_MQ_REQ_PM requests to a device that is runtime suspended
causes runtime-suspended devices not to resume as they should. The request
which should cause a runtime resume instead gets issued directly, without
resuming the device first. Of course the device can't handle it properly,
the I/O fails, and the device remains suspended.
The problem is fixed by checking that the queue's runtime-PM status isn't
RPM_SUSPENDED before allowing a request to be issued, and queuing a
runtime-resume request if it is. In particular, the inline
blk_pm_request_resume() routine is renamed blk_pm_resume_queue() and the
code is unified by merging the surrounding checks into the routine. If the
queue isn't set up for runtime PM, or there currently is no restriction on
allowed requests, the request is allowed. Likewise if the BLK_MQ_REQ_PM
flag is set and the status isn't RPM_SUSPENDED. Otherwise a runtime resume
is queued and the request is blocked until conditions are more suitable.
[ bvanassche: modified commit message and removed Cc: stable because
without the previous patches from this series this patch would break
parallel SCSI domain validation + introduced queue_rpm_status() ]
Link: https://lore.kernel.org/r/20201209052951.16136-9-bvanassche@acm.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-and-tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4d34da715e3cb7e0741fe603dcd511bed067e00 ]
Remove flag RQF_PREEMPT and BLK_MQ_REQ_PREEMPT since these are no longer
used by any kernel code.
Link: https://lore.kernel.org/r/20201209052951.16136-8-bvanassche@acm.org
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5c3b5796866f85354a5ce76a28f8ffba0dcefc7e upstream.
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f427 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c87 ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 436e980e2ed526832de822cbf13c317a458b78e1 upstream.
depmod is not guaranteed to be in /sbin, just let make look for
it in the path like all the other invoked programs
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f3e900b628226011a5f71c19e53b175c014eb58 ]
In order to conduct FFU or RPMB operations, UFS needs to clear UNIT
ATTENTION condition. Clear it explicitly so that we get no failures during
initialization.
Link: https://lore.kernel.org/r/20201117165839.1643377-4-jaegeuk@kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cedd1862be7e666be87ec824dabc6a2b05618f36 ]
Commit 436e980e2ed5 ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36845663843fc59c5d794e3dc0641472e3e572da ]
Some graphic card has very big memory on chip, such as 32G bytes.
In the following case, it will cause overflow:
pool = gen_pool_create(PAGE_SHIFT, NUMA_NO_NODE);
ret = gen_pool_add(pool, 0x1000000, SZ_32G, NUMA_NO_NODE);
va = gen_pool_alloc(pool, SZ_4G);
The overflow occurs in gen_pool_alloc_algo_owner():
....
size = nbits << order;
....
The @nbits is "int" type, so it will overflow.
Then the gen_pool_avail() will return the wrong value.
This patch converts some "int" to "unsigned long", and
changes the compare code in while.
Link: https://lkml.kernel.org/r/20201229060657.3389-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reported-by: Shi Jiasheng <jiasheng.shi@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87dbc209ea04645fd2351981f09eff5d23f8e2e9 ]
Make <asm-generic/local64.h> mandatory in include/asm-generic/Kbuild and
remove all arch/*/include/asm/local64.h arch-specific files since they
only #include <asm-generic/local64.h>.
This fixes build errors on arch/c6x/ and arch/nios2/ for
block/blk-iocost.c.
Build-tested on 21 of 25 arch-es. (tools problems on the others)
Yes, we could even rename <asm-generic/local64.h> to
<linux/local64.h> and change all #includes to use
<linux/local64.h> instead.
Link: https://lkml.kernel.org/r/20201227024446.17018-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6044f714b256259df9611ff49af433e5411c5c8 ]
Instead of submitting all SCSI commands submitted with scsi_execute() to a
SCSI device if rpm_status != RPM_ACTIVE, only submit RQF_PM (power
management requests) if rpm_status != RPM_ACTIVE. This patch makes the SCSI
core handle the runtime power management status (rpm_status) as it should
be handled.
Link: https://lore.kernel.org/r/20201209052951.16136-7-bvanassche@acm.org
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
